* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: revert portions of "UNUSUAL_DEV: Sync up some reported devices from Ubuntu"
  usb: Remove broken optimisation in OHCI IRQ handler
  USB: at91_udc: correct hanging while disconnecting usb cable
  USB: use IRQF_DISABLED for HCD interrupt handlers
  USB: fix locking loop by avoiding flush_scheduled_work
  usb.h: fix kernel-doc warning
  USB: option: Bind to the correct interface of the Huawei E220
  USB: cp2101: new device id
  usb-storage: Fix devices that cannot handle 32k transfers
  USB: sierra: fix product id

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: fix ->io_32bit race in set_io_32bit()
  ide: remove stale changelog from ide-probe.c
  ide: remove stale changelog from ide-disk.c
  ide: remove dead code from __ide_dma_test_irq()
  hpt366: fix HPT37x PIO mode timings (take 2)
  pdc202xx_new: fix Promise TX4 support
  ide-cd: remove dead post_transform_command()
  ide: DMA reporting and validity checking fixes (take 3)
  ide: add /sys/bus/ide/devices/*/{model,firmware,serial} sysfs entries
  ide: coding style fixes for drivers/ide/setup-pci.c
  ide: fix ide_scan_pcibus() error message
  ide: deprecate CONFIG_BLK_DEV_OFFBOARD
  ide: add missing checks for control register existence
  ide-scsi: add ide_scsi_hex_dump() helper

This reverts one change from 67fa1062
that prevented userspace from seing the "driver disk" lun in a san disk
device.  The kernel shouldn't do this, it's up to userspace to handle
this properly, if it somehow wants to filter this away.


Cc: Ben Collins <bcollins@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The OHCI IRQ handler has an optimisation that avoids reading some
chip registers when the controller reports that the interrupt was
triggered *only* because completed requests were written into the
controller's "done list" and handed to the host.

This mechanism can't be used on some controllers.  Among others, it
fails for the SA1111 and the AMCC 440EP PowerPC processor.

This patch removes the optimisation and makes the code clearer.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Correct hanging while disconnecting the USB device cable.  Prevent a race
between vbus and UDP interrupts.  This bug was tracked on at91sam9260ek
boards.

A usb resume interrupt was firing after the vbus interrupt : the IP was
then already stoped and not able to deal with it (no more clock).  A simple
interrupt disabling is ok as the "end of bus reset" irq is non maskable and
ok to resume the USB device IP.
Signed-off-by: NNicolas Ferre <nicolas.ferre@rfo.atmel.com>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Host controller IRQs are supposed to be serviced with interrupts
disabled.  This patch (as1026) adds an IRQF_DISABLED flag to all the
controller drivers that lack it.  It also replaces the
spin_lock_irqsave() and spin_unlock_irqrestore() calls in uhci_irq()
with simple spin_lock() and spin_unlock().

This fixes Bugzilla #9335.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1027) replaces a call to flush_scheduled_work() -- a
dangerous routine to invoke, especially while holding any sort of lock
-- with calls to cancel_work_sync() and cancel_delayed_work_sync().

This fixes Bugzilla #9532.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix kernel-doc warning in usb.h:
Warning(linux-2.6.24-rc3-git7//include/linux/usb.h:166): No description found for parameter 'sysfs_files_created'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes a bunch of problems we are having with the Huawei devices...
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NJaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds a device ID for the Aerocomm Radio Modem, which uses the
cp2102.  I'm sure changing num_bulk_in/num_bulk_out to NUM_DONT_CARE
is the wrong fix, but this is the only device I have with a cp2102,
so I have no idea what a good global value would be, if there is one.
Zero didn't work with this device.

From: Jeff Long <JeffLong@mitre.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When a device cannot handle the smallest previously limited transfer
size (64 blocks) without stalling, limit the device to the amount of
packets that fit in a platform native page.

The lowest possible limit is PAGE_CACHE_SIZE, so if the device is ever
used on a platform that has larger than 8K pages, you lose unless you
can convince the device firmware folks to fix the issue.

Cc: Mathew Dharm <mdharm-scsi@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NDoug Maxey <dwm@austin.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Attached is a patch to fix the addition of the new product ids I sent.

It is against 2.6.24-rc4, as Linus included the broken version of the
patch I sent you in that tree. :(

Not sure if this is the right method to go about this, but hopefully I got
it right this time.
Signed-off-by: NAndrew Gilmore <agilmore@wirelessbeehive.com>
CC: Kevin Lloyd <klloyd@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (6820): s5h1409: QAM SNR related fixes
  V4L/DVB (6819): i2c: fix drivers/media/video/bt866.c
  V4L/DVB (6814): Makefile: always enter video/
  V4L/DVB (6798): saa7134: enable LNA in analog mode for Hauppauge WinTV HVR-1110
  V4L/DVB (6803): buf-core.c locking fixes

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] add Nano 7240 driver
  [WATCHDOG] ipmi: add the standard watchdog timeout ioctls
  [WATCHDOG] IT8212F watchdog driver
  [WATCHDOG] Sbus: cpwatchdog, remove SPIN_LOCK_UNLOCKED
  [WATCHDOG] bfin_wdt, remove SPIN_LOCK_UNLOCKED
  [WATCHDOG] Stop looking for device as soon as one is found
  [WATCHDOG] at32ap700x_wdt: add support for boot status and add fix for silicon errata

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/fix-kbuild:
  kbuild: re-enable Makefile generation in a new O=... directory

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/ehca: Fix lock flag variable location, bump version number
  IB/ehca: Serialize HCA-related hCalls if necessary
  IB/ehca: Return correct number of SGEs for SRQ

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 4694/1: IXP4xx: Update clockevent support for shutdown and resume
  [ARM] 4710/1: Fix coprocessor 14 usage for debug messages via ICEDCC
  [ARM] 4690/1: PXA: fix CKEN corruption in PXA27x AC97 cold reset code
  [ARM] 4667/1: CM-X270 fixes

Add proper support for CLOCK_EVT_MODE_RESUME and in the process fix
CLOCK_EVT_MODE_SHUTDOWN so that only the enable bits are toggled for both.
Signed-off-by: NKevin Hilman <khilman@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

According to ARM7TDMI Technical Reference Manual (ARM DDI 0210C) writing
to the DCC data write register coproc dest registers are 1 and 0, not 0
and 1.

ARM920T TRM (ARM DDI 0151C) agrees on that.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NUwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  [IRDA]: irda parameters warning fixes.
  [IRDA]: stir4200 fixes.
  [IRDA]: irlmp_unregister_link() needs to free lsaps.
  [IRDA]: mcs7780 needs to free allocated rx buffer.
  [IRDA]: Race between open and disconnect in irda-usb.
  [SCTP]: Flush fragment queue when exiting partial delivery.
  [AX25]: Locking dependencies fix in ax25_disconnect().
  [IPV4]: Make tcp_input_metrics() get minimum RTO via tcp_rto_min()
  [IPV6]: Fix the return value of ipv6_getsockopt
  [BRIDGE]: Assign random address.
  [IPV4]: Updates to nfsroot documentation
  [ATM]: Fix compiler warning noise with FORE200E driver
  [NETFILTER]: bridge: fix missing link layer headers on outgoing routed packets
  [SYNCPPP]: Endianness and 64bit fixes.
  [TIPC]: Fix semaphore handling.
  [NETFILTER]: xt_hashlimit should use time_after_eq()
  [XFRM]: Display the audited SPI value in host byte order.
  [NETFILTER]: ip_tables: fix compat copy race
  [NETFILTER]: ctnetlink: set expected bit for related conntracks

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC32]: Silence sparc32 warnings on missing syscalls.
  [SPARC64]: Fix two kernel linear mapping setup bugs.

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [S390] pud_present/pmd_present bug.

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] Make PS3_SYS_MANAGER default y, not m
  [POWERPC] Fix rounding bug in emulation for double float operating
  [POWERPC] iSeries: don't printk with HV spinlock held
  [POWERPC] 82xx: mpc8272ads, pq2fads: Update defconfig with CONFIG_FS_ENET_MDIO_FCC
  [POWRPC] CPM2: Eliminate section mismatch warning in cpm2_reset().
  [POWERPC] Kill non-existent symbols from ksyms and commproc.h
  [POWERPC] Fix typo #ifdef -> #ifndef

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Ensure that ST0_FR is never set on a 32 bit kernel
  [MIPS] time: Delete weak definition of plat_time_init() due to gcc bug.
  [MIPS] PCI: Make pcibios_fixup_device_resources ignore legacy resources.
  [MIPS] Atlas, Malta: Don't free firmware memory on free_initmem.
  [MIPS] Alchemy: fix off by two error in __fixup_bigphys_addr()
  [MIPS] Alchemy: fix PCI resource conflict
  [MIPS] time: Set up Cobalt's mips_hpt_frequency

Git commit 3610cce8 (yeah my own :-/)
introduced a bug in regard to pud/pmd table entries.
If the address of the page table refered to by a pud/pmd value happens
to have zeroes in the lower 32 bits, pud_present and pmd_present return
false. The obvious effect is that this triggers the BUG_ON in exit_mmap
because some ptes will not get released on process end.  Worse is that
the next fault for memory covered by that pud/pmd will allocate another
pmd/pte table and populate the pud/pmd entry. The old page table
entries hanging below this entry are lost!

The fix is simple, properly check against 0. The check is added for
pud_none/pmd_none as well even if these two functions work because
the invalid bit is in the lower 32 bits.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch fixes:
  CHECK   /home/kernel/src/net/irda/parameters.c
/home/kernel/src/net/irda/parameters.c:466:2: warning: Using plain integer as NULL pointer
/home/kernel/src/net/irda/parameters.c:520:2: warning: Using plain integer as NULL pointer
/home/kernel/src/net/irda/parameters.c:573:2: warning: Using plain integer as NULL pointer
Signed-off-by: NRichard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Olaf Hartmann <olaf.hartmann@s1998.tu-chemnitz.de>

The attached patch observes the stir4200 fifo size and will clear the
fifo, if the size is increasing, while it should be transmitting bytes
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While testing the mcs7780 based IrDA USB dongle I've stumbled upon
memory leak in irlmp_unregister_link(). Hashbin for lsaps is created in
irlmp_register_link and should probably be freed in irlmp_unregister_link().
Signed-off-by: NHinko Kocevar <hinko.kocevar@cetrtapot.si>
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While testing the mcs7780 based IrDA USB dongle I've stumbled upon
memory leak in mcs_net_close(). Patch below fixes it.
Signed-off-by: NHinko Kocevar <hinko.kocevar@cetrtapot.si>
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems to me that irda_usb_net_open() must set self->netopen
under spinlock or disconnect() may fail to kill all URBs, if it is called
while an interface is opened.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At the end of partial delivery, we may have complete messages
sitting on the fragment queue.  These messages are stuck there
until a new fragment arrives.  This can comletely stall a
given association.  When clearing partial delivery state, flush
any complete messages from the fragment queue and send them on
their way up.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bernard Pidoux reported these lockdep warnings:

[ INFO: possible irq lock inversion dependency detected ]
2.6.23.1 #1
---------------------------------------------------------
fpac/4933 just changed the state of lock:
 (slock-AF_AX25){--..}, at: [<d8be3312>] ax25_disconnect+0x46/0xaf
 [ax25]
 but this lock was taken by another, soft-irq-safe lock in the past:
  (ax25_list_lock){-+..}

  and interrupts could create inverse lock ordering between them.
  [...]

[ INFO: inconsistent lock state ]
2.6.23.1 #1
---------------------------------
inconsistent {in-softirq-W} -> {softirq-on-W} usage.
ax25_call/4005 [HC0[0]:SC0[0]:HE1:SE1] takes:
 (slock-AF_AX25){-+..}, at: [<d8b79312>] ax25_disconnect+0x46/0xaf [ax25]
 [...]

This means slock-AF_AX25 could be taken both from softirq and process
context with softirqs enabled, so it's endangered itself, but also makes
ax25_list_lock vulnerable. It was not 100% verified if the real lockup
can happen, but this fix isn't very costly and looks safe anyway.
(It was tested by Bernard with 2.6.23.9 and 2.6.24-rc5 kernels.)


Reported_by: Bernard Pidoux <pidoux@ccr.jussieu.fr>
Tested_by: Bernard Pidoux <pidoux@ccr.jussieu.fr>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp_input_metrics() refers to the built-time constant TCP_RTO_MIN
regardless of configured minimum RTO with iproute2.
Signed-off-by: NSatoru SATOH <satoru.satoh@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If CONFIG_NETFILTER if not selected when compile the kernel source code, 
ipv6_getsockopt will returen an EINVAL error if optname is not supported by
the kernel. But if CONFIG_NETFILTER is selected, ENOPROTOOPT error will 
be return.

This patch fix to always return ENOPROTOOPT error if optname argument of 
ipv6_getsockopt is not supported by the kernel.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Assigning a valid random address to bridge device solves problems
when bridge device is brought up before adding real device to bridge.
When the first real device is added to the bridge, it's address
will overide the bridges random address.

Note: any device added to a bridge must already have a valid
ethernet address.
 br_add_if -> br_fdb_insert -> fdb_insert -> is_valid_ether_addr
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The difference between ip=off and ip=::::::off has been a cause of much
confusion.  Document how each behaves, and do not contradict ourselves by
saying that "off" is the default when in fact "any" is the default and is
descibed as being so lower in the file.
Signed-off-by: NAmos Waterland <apw@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc throws these warnings with:

CONFIG_ATM_FORE200E=m
# CONFIG_ATM_FORE200E_PCA is not set

drivers/atm/fore200e.c:2695: warning: 'fore200e_pca_detect' defined but
not used
drivers/atm/fore200e.c:2748: warning: 'fore200e_pca_remove_one' defined
but not used

By moving the #ifdef CONFIG_ATM_FORE200E_PCA around those two functions,
the compiler warnings are silenced.
Signed-off-by: NTom "spot" Callaway <tcallawa@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Damien Thebault, the double POSTROUTING hook invocation
fix caused outgoing packets routed between two bridges to appear without
a link-layer header. The reason for this is that we're skipping the
br_nf_post_routing hook for routed packets now and don't save the
original link layer header, but nevertheless tries to restore it on
output, causing corruption.

The root cause for this is that skb->nf_bridge has no clearly defined
lifetime and is used to indicate all kind of things, but that is
quite complicated to fix. For now simply don't touch these packets
and handle them like packets from any other device.
Tested-by: NDamien Thebault <damien.thebault@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

	* trivial annotations
	* long != 32bit, use __be32
	* wrong endianness in sending CISCO_ADDR_REPLY
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As noted by Kevin, tipc's release() does down_interruptible() and
ignores the return value.  So if signal_pending() we'll end up doing
up() on a non-downed semaphore.  Fix.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>