ALC861-VD lenovo model causes overflow of spec->init_verbs entries due to
the recent changes.  Simply increase the array size to avoid the overflow.
Reported-by: NLuca Tettamanti <kronos.it@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since patch_alc268() doesn't call set_capture_mixer() (due to its h/w
design different from other siblings), it needs to call fixup_automic_adc()
explicitly to set up the auto-mic routing.  Otherwise the indices for
int/ext mics aren't set properly.

Reference: Novell bnc#544899
	http://bugzilla.novell.com/show_bug.cgi?id=544899Signed-off-by: NTakashi Iwai <tiwai@suse.de>

alc_subsystem_id() tries to pick up a headphone pin if not configured,
but this caused side-effects as the problem in commit
15870f05.

This patch fixes the driver behavior to pick up invalid HP pins; at least,
the pins that are listed as the primary outputs aren't taken any more.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ASUS A7K needs additional GPIO1 bit setup; it has to be cleared.
Added a new fixup hook for this laptop so that it works as is.

Refernece: Novell bnc#494309
	http://bugzilla.novell.com/show_bug.cgi?id=494309Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The recent auto-parser doesn't work for machines with a single output
with ALC861, such as Toshiba laptops, because alc_subsystem_id() sets
the hp_pins[0] while it's listed in line_outs[0].
This ends up with the doubled initialization of the same mixer widget,
and it mutes the DAC route because hp_pins has no DAC assigned.

To fix this problem, just check spec->autocfg.hp_outs and speaker_outs
so that they are really detected pins.

Reference: Novell bnc#544161
	http://bugzilla.novell.com/show_bug.cgi?id=544161Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The auto-parser for ALC662/663/272 codecs doesn't work properly when
a speaker is connected to mono NID 0x17, and doesn't handle the dynamic
DAC assignment properly.

This patch fixes the issues and also improves the assignment of DACs
so that HP and speakers can have independent volume controls.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Patch was tested on Toshiba NB200 and is found to enable sound.
Signed-off-by: NManoj Iyer <manoj.iyer@canonical.com>
Cc: stable@kernel.org
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In the commit fdbc6626, I mistakenly
replaced the capture mixer array for ALC268_ACER to nosrc version
although this should be kept to alt_mixer.  Now fixed back.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The headphone and speaker mixer elements aren't properly set for
MSI GX620 with targa-8ch-dig quirk.
Also fixed the speaker volume control for other ALC883-targa quirks,
too.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The HP laptops with ALC268 codec seem working better with model=auto
than model=toshiba; e.g. the auto model fixes missing digital outputs.
Let's fix quirk entry to choose auto model explicitly.
Tested-by: NJens Jorgensen <jbj1@ultraemail.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The model clevo-m540r was created with 6-channel and digital support. All
functions verified except spdif. Tested with a VIT D2000 laptop which has:

[lspci extract]
 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio
Controller [8086:284b] (rev 03)
        Subsystem: CLEVO/KAPOK Computer Device [1558:5409]

[/proc/asound/card0/codec\#0 header]
Codec: Realtek ALC883
Address: 0
Function Id: 0x1
Vendor Id: 0x10ec0883
Subsystem Id: 0x15585409
Revision Id: 0x100002

[Added a comment about HP mute and the model description by tiwai]
Signed-off-by: NDhionel Diaz <ddiaz@cenditel.gob.ve>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix the headphone pin routing of ALC268/ALC269 codecs.  Using alc882
routine doesn't work because alc268/alc269 parser assumes the
independent DACs for both HP and speaker outputs.  Need to assign the
DAC depending on the pin.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch fixes the wrong headphone output routing for MacBookPro 3,1/4,1
quirk with ALC889A codec, which caused the silent headphone output.
Also, this gives the individual Headphone and Speaker volume controls.

Reference: kernel bug#14078
	http://bugzilla.kernel.org/show_bug.cgi?id=14078Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>

1) Added support of internal subwoofer (it sounds!!!)
2) Auto muting front speakers and internal subwoofer on headphones plug.
3) Internal mic works.
4) 3 channel mods (jack maps):
       black  pink         blue
2ch: front   ext mic     line in
4ch: front   ext mic     surround
6ch: front   CLFE        surround
  Can be changed in mixer.
5) Sound can be recorded from:
 Internal mic
 Ext mic
 Cd
 Line in
6) 2 separate capture channels.
Signed-off-by: NDenis Kuplyakov <dener.kup@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The last patch in this series is for ALC662; pretty similar as the
previous patch for ALC861-VD.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

One more patch to give a better name for the primary output controls,
this time for ALC861-VD codec.  The change is simple, just checking the
pin connection whether it's a speaker-out.  When both speaker and HP
are assigned, we name the volume as "PCM" as this influences on both
outputs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Similar improvements for ALC262 codec like previous two commits:
assign a better name, either Master or Speaker, for the primary output
controls.

However, in the case of ALC262 codec, the necessary changes are larger
than others because we need to check the possibility of different mixer
amps depending on the pins.  The pin 0x16 is mono, and bound with the
dedicated mixer 0x0e while other pins are bound with 0x0c.  Thus, there
are two possible volumes.

When only one of them is used, we can name it as "Master".  OTOH, when
both are used at the same time, they have to be named uniquely.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Instead of fixed "Front" mixer name, try to assign a better name, e.g.
"Master" or "Speaker" fot the primary output volume controls of ALC260
codec.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When there is only one DAC is used for ALC880, try to assign a better
name, either Speaker or Front, depending on the output pin type.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Provide a standard parser for input pins to create the input mixer
and input source controls instead of having a difference one for each
Realtek codec.  The new helper parses the codec connections dynamically
isntead of fixed indicies.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Reuse a part of the code of ALC268 parser for ALC269.
This will change the default output volume either to Front or Speaker
depending on the pin configuration.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

There are many variants of Toshiba laptops with ALC268 codec, and
it seems that a few of them don't work with model=toshiba preset
since they have the secondary ALC268 codec just for HDMI output.
This is a regression due to the previous clean-up work to merge all
Toshiba quirk entries into a single check.

This patch adds the identification of such laptops to apply the
standard BIOS-probing method.  Unfortunately, Toshiba laptops have
all the same PCI SSID, so we need to check the codec SSID to identify
each device.
Tested-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The auto-mic clean-up patches caused regressions on some ALC268 models
that have no proper input_mux but with "Input Source" mixer elements.
Such a combination results in Oops when accessed.

[A reason why set_capture_mixer() isn't used in patch_alc268() is that
ALC268 codec have HDA_OUTPUT direction for capture volumes unlike other
codecs.  Thus it needs own definitions of capture elements.]

This patch fixes the issues:
- Add a capture mixer definition without input-source
- Use the new capture mixer appropriately
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

With auto config model of alc268 realtek codec, it allows to select any
of possible available digital microphone inputs when only one is
available. For example, when only digital mic in nid 0x12 is available,
on second input source it will allow you to select unavailable digital
mic in nid 0x13. The problem is that selecting unavailable digital mic
creates a source of noise when recording (I'm not sure if this happens
on all machines with alc268 and only one digital mic input, but testing
on a quanta uw1 netbook a lot of noise is introduced in recording from
digital mic 0x12/first input source, when you select the unavailable
digital mic 0x13 for capture source 0x24 in the second input source in
mixer).

Then to avoid noise when recording from digital mic with auto model in
this case, prevent a digital mic input source to be selected if
microphone is not available.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Move static codes to setup from init_hook for each model.

Also, use the common auto-mic selection helper for devices that support
auto-mic selection.  They just need to set up ext_mic, int_mic and
auto_mic flag in the setup section.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added setup hook to ALC preset struct to be called at in the parser
but not at each init callback.
This can be used for setting up the static pins, etc, while the
init hook should be used for updating the status again.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some Realtek codecs don't provide the full connections for certain pins
from each ADC; e.g. ACL662/ALC272 gives only one of two digital-mic pins
for each ADC.  Thus, depending on the digital mic pin, the ADC/MUX to be
used has to be chosen properly.

This patch adds the check of the connectivity of pins at auto-mic mode.
If no proper connectivity is found, auto_mic flag is turned off to be
sure.

Also the mux_idx is determined during this check so it won't be checked
in the unsol event any more.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ALC269 and ALC861-VD parsers override the ADC definitions
unconditionally without checking the spec definition.  This causes
the problem when any inconsistent ADC is set up in the device quirk
(like ALC272 with digital-mic).

This patch avoids the overriding by adding the proper checks.

Reference: Novell bnc#529467
	https://bugzilla.novell.com/show_bug.cgi?id=529467Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the auto-mic feature is enabled, we should support only one
capture stream.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added the support for automatic mic selection via plugging for
Realtek codecs (in auto-probing mode).  The auto-mic mode is enabled
only when one internal mic and one external mic are present.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Without the initialization of vmaster NID, the dB information got
confused for ALC269 codec.

Reference: Novell bnc#527361
	https://bugzilla.novell.com/show_bug.cgi?id=527361Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>

Check whether index is within bounds before testing the element.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use model=lenovo instead of model=dallas for Toshiba Satellite A135-S4527
with ALC861-VD codec.

Reference: Novell bnc#526325
	https://bugzilla.novell.com/show_bug.cgi?id=526325Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The name buf with size 16 is too short for some codec names, e.g.
truncated like "ALC861-VD Analo".  Now the size is doubled.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

It auto mutes all 8-channel outputs at rear panel when
the front panel headphone is connected.
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This 2-channel mode is useful in that it will broadcast
a 2-channel audio stream to all front/side/... ports.
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The sentense "Unknown model for xxx, ..." makes people too nervous
and drives them to a direction to a wrong "fix" by giving any
mismatching model option.

Let's rephrase the messages to be more nice and easy (at least that
won't make people suspect conspiracies).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add a helper macro to retrieve the widget type from wiget cap bits.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The master mute switch is wrongly implemented as checking the pointer
instead of its value, thus it can be never muted.  This patch fixes
the issue.

Reference: Novell bnc#404873
	https://bugzilla.novell.com/show_bug.cgi?id=404873Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>