We had several problems here.  First, a race condition on QP1 mac
handling between mlx4_ib_update_qps and mlx4_ib_modify_qp, which is
fixed by taking the qp mutex in mlx4_ib_update_qps.

Also, qp->pri.smac_port was not updated in mlx4_ib_update_qps.

Last, in __mlx4_ib_modify_qp we did not properly handle the case where
the mac is zero, but port is non-zero.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Automatic Path Migration is not supported under RoCE. Therefore,
return a "not-supported" error if the caller attempts to set an
alternate path in a QP context.

In addition, if there are no IB ports configured, do not report
APM capability in the device flags returned by mlx4_ib_query_device.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The source MAC is needed in RoCE when building the QP1 header.

Currently, this is obtained from the source net device. However, the net
device may not yet exist, or can be destroyed in parallel to this QP1 send
operation (e.g through the VPI port change flow) so accessing it may cause
a kernel crash.

To fix this, we maintain a source MAC cache per port for the net device in
struct mlx4_ib_roce.  This cached MAC is initialized to be the default MAC
address obtained during HCA initialization via QUERY_PORT. This cached MAC
is updated via the netdev event notifier handler.

Since the cached MAC is held in an atomic64 object, we do not need locking
when accessing it.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

We wrongly tested QP context bits without BE conversion
as was spotted by sparse...

drivers/infiniband/hw/mlx4/qp.c:1685:38: sparse: restricted __be32 degrades to integer

Fix that!

Fixes: d2fce8a9 ('mlx4: Set user-space raw Ethernet QPs to properly handle VXLAN traffic')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Raw Ethernet QPs opened from user-space lack the proper setup to
recieve/handle VXLAN traffic when VXLAN offloads are enabled.

Fix that by adding a tunnel steering rule on top of the normal unicast
steering rule and set the tunnel_type field in the QP context.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two kzalloc() calls which were not converted to use value of
gfp passed to create_qp_common() instead of using hardcoded GFP_KERNEL
in 40f2287b ("IB/mlx4: Implement IB_QP_CREATE_USE_GFP_NOIO").  Fix
this by passing gfp value down properly.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Modify the various routines used to allocate memory resources which
serve QPs in mlx4 to get an input GFP directive.  Have the Ethernet
driver to use GFP_KERNEL in it's QP allocations as done prior to this
commit, and the IB driver to use GFP_NOIO when the IB verbs
IB_QP_CREATE_USE_GFP_NOIO QP creation flag is provided.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This commit adds the infrastructure for enabling selected VFs to
operate SMI (QP0) MADs without restriction.

Additionally, for these enabled VFs, their QP0 proxy and tunnel QPs
are MLX QPs.  As such, they operate over VL15.  Therefore, they are
not affected by "credit" problems or changes in the VLArb table (which
may shut down VL0).

Non-enabled VFs may only create UD proxy QP0 qps (which are forced by
the hypervisor to send packets using the q-key it assigns and places
in the qp-context).  Thus, non-enabled VFs will not pose a security
risk.  The hypervisor discards any privileged MADs it receives from
these non-enabled VFs.

By default, all VFs are NOT enabled, and must explicitly be enabled
by the administrator.

The sysfs interface which operates the VF enablement infrastructure
is provided in the next commit.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Currently, VFs in SRIOV VFs are denied QP0 access.  The main reason
for this decision is security, since Subnet Management Datagrams
(SMPs) are not restricted by network partitioning and may affect the
physical network topology.  Moreover, even the SM may be denied access
from portions of the network by setting management keys unknown to the
SM.

However, it is desirable to grant SMI access to certain privileged
VFs, so that certain network management activities may be conducted
within virtual machines instead of the hypervisor.

This commit does the following:

1. Create QP0 tunnel QPs for all VFs.

2. Discard SMI mads sent-from/received-for non-privileged VFs in the
   hypervisor MAD multiplex/demultiplex logic.  SMI mads from/for
   privileged VFs are allowed to pass.

3. MAD_IFC wrapper changes/fixes.  For non-privileged VFs, only
   host-view MAD_IFC commands are allowed, and only for SMI LID-Routed
   GET mads.  For privileged VFs, there are no restrictions.

This commit does not allow privileged VFs as yet.  To determine if a VF
is privileged, it calls function mlx4_vf_smi_enabled().  This function
returns 0 unconditionally for now.

The next two commits allow defining and activating privileged VFs.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

When we receive a netdev event indicating a netdev change and/or
a netdev address change, we must change the MAC index used by the
proxy QP1 (in the QP context), otherwise RoCE CM packets sent by the
VF will not carry the same source MAC address as the non-CM packets.

We use the UPDATE_QP command to perform this change.

In order to avoid modifying a QP context based on netdev event,
while the driver attempts to destroy this QP (e.g either the mlx4_ib
or ib_mad modules are unloaded), we use mutex locking in both flows.

Since the relevant mlx4 proxy GSI QP is created indirectly by the
mad module when they create their GSI QP, the mlx4 didn't need to
keep track on that QP prior to this change.

Now, when QP modifications are needed to this QP from within the
driver, we added refernece to it.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following warning for the mlx4 driver:

    $ make M=drivers/infiniband C=2 CF=-D__CHECK_ENDIAN__
    drivers/infiniband/hw/mlx4/qp.c:1885:31: warning: restricted __be16 degrades to integer
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,

This is achieved as follows:
Outgoing MADs:
    1. Source MAC: obtained from the CQ completion structure
       (struct ib_wc, smac field).
    2. Destination MAC: obtained from the tunnel header
    3. vlan_id: obtained from the tunnel header.
Incoming MADs
    1. The source (i.e., remote) MAC and vlan_id are passed in
       the tunnel header to the proxy QP1.

VST mode support:
     For outgoing MADs,  the vlan_id obtained from the header is
        discarded, and the vlan_id specified by the Hypervisor is used
        instead.
     For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
        "invalid" vlan (0xffff)  is substituted when forwarding to the slave.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IB side of RoCE requires the MAC table index of the
MAC address used by its QPs.

To obtain the real MAC index, the IB side registers the
MAC (increasing its ref count, and also returning the
real MAC index) during the modify-qp sequence.

This protects against the ETH side deleting or modifying
that MAC table entry while the QP is active.

Note that until the modify-qp command returns success,
the MAC and VLAN information only has "candidate" status.
If the modify-qp succeeds, the "candidate" info is promoted
to the operational MAC/VLAN info for the qp. If the modify fails,
the candidate MAC/VLAN is unregistered, and the old qp info
is preserved.

The patch is a bit complex, because there are multiple qp
transitions where the primary-path information may be
modified:  INIT-to-RTR, and SQD-to-SQD.

Similarly for the alternate path information.

Therefore the code must handle cases where path information
has already been entered into the QP context by previous
qp transitions.

For the MAC address, the success logic is as follows:
1. If there was no previous MAC, simply move the candidate
   MAC information to the operational information, and reset
   the candidate MAC info.
2. If there was a previous MAC, unregister it.  Then move
   the MAC information from candidate to operational, and
   reset the candidate info (as in 1. above).

The MAC address failure logic is the same for all cases:
 - Unregister the candidate MAC, and reset the candidate MAC info.

For Vlan registration, the logic is similar.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This requires the following modifications:
1. Fix build_mlx4_header to properly fill in the ETH fields
2. Adjust mux and demux QP1 flow to support RoCE.

This commit still assumes only one GID per slave for RoCE.
The commit enabling multiple GIDs is a subsequent commit, and
is done separately because of its complexity.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IP based RoCE gids don't store Ethernet L2 parameters, MAC and VLAN.

Therefore, we need to extract them from the CQE and place them in
struct ib_wc (to be used for cases were they were taken from the gid).

Also, when modifying a QP or building address handle, instead of
parsing the dgid to get the MAC and VLAN, take them from the address
handle attributes.
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This patch add the support for Ethernet L2 attributes in the
verbs/cm/cma structures.

When dealing with L2 Ethernet, we should use smac, dmac, vlan ID and priority
in a similar manner that the IB L2 (and the L4 PKEY) attributes are used.

Thus, those attributes were added to the following structures:

* ib_ah_attr - added dmac
* ib_qp_attr - added smac and vlan_id, (sl remains vlan priority)
* ib_wc - added smac, vlan_id
* ib_sa_path_rec - added smac, dmac, vlan_id
* cm_av - added smac and vlan_id

For the path record structure, extra care was taken to avoid the new
fields when packing it into wire format, so we don't break the IB CM
and SA wire protocol.

On the active side, the CM fills. its internal structures from the
path provided by the ULP.  We add there taking the ETH L2 attributes
and placing them into the CM Address Handle (struct cm_av).

On the passive side, the CM fills its internal structures from the WC
associated with the REQ message.  We add there taking the ETH L2
attributes from the WC.

When the HW driver provides the required ETH L2 attributes in the WC,
they set the IB_WC_WITH_SMAC and IB_WC_WITH_VLAN flags. The IB core
code checks for the presence of these flags, and in their absence does
address resolution from the ib_init_ah_from_wc() helper function.

ib_modify_qp_is_ok is also updated to consider the link layer. Some
parameters are mandatory for Ethernet link layer, while they are
irrelevant for IB.  Vendor drivers are modified to support the new
function signature.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This patch adds support for steerable (NETIF) QP creation.  When we
create the device, we allocate a range of steerable QPs.

Afterward when a QP is created with the NETIF flag, it's allocated
from this range.  Allocation is managed by bitmap allocator.

Internal steering rules for those QPs is automatically generated on
their creation.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

When the link type is Ethernet, setting the link type in the QP
context will enable TCP/IP stateless offloads (checksum, LSO, RSS) for
RAW PACKET Ethernet QPs.  For IB UD QPs this worked OK since the value
assumed by the firmware for IB link layer is zero.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Fix the asymmetric behavior w.r.t VLAN insertion/stripping for RAW
PACKET QPs -- we don't insert on send and need not strip on receive.
Signed-off-by: NDotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

* Implement memory windows binding in mlx4_ib_post_send.

* Implement mlx4_ib_bind_mw by deferring to mlx4_ib_post_send.

* Rename MLX4_WQE_FMR_PERM_* flags to MLX4_WQE_FMR_AND_BIND_PERM_*,
  indicating that they are used both for fast registration work
  requests, and for memory window bind work requests.
Signed-off-by: NHaggai Eran <haggaie@mellanox.com>
Signed-off-by: NShani Michaeli <shanim@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Building qp.o triggers this gcc warning:

    drivers/infiniband/hw/mlx4/qp.c: In function ‘mlx4_ib_post_send’:
    drivers/infiniband/hw/mlx4/qp.c:1862:62: warning: ‘vlan’ may be used uninitialized in this function [-Wmaybe-uninitialized]
    drivers/infiniband/hw/mlx4/qp.c:1752:6: note: ‘vlan’ was declared here

Looking at the code it is clear 'vlan' is only set and used if 'is_eth'
is non-zero. But by initializing 'vlan' to 0xffff, on

    gcc (Ubuntu 4.7.2-22ubuntu1) 4.7.2

on x86-64 at least, we fix the warning, and the compiler was already
setting 'vlan' to 0 in the generated code, so there's no real downside.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>

[ Get rid of unnecessary move of 'is_vlan' initialization.  - Roland ]
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Matches the way they're used, and actually lets at least x86-64 generate
better code:

    add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-38 (-38)
    function                                     old     new   delta
    mlx4_ib_post_send                           4416    4378     -38
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Remove unused fields from the local invalidate WQE segment structure.
Signed-off-by: NHaggai Eran <haggaie@mellanox.com>
Signed-off-by: NShani Michaeli <shanim@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Previously, the structure of a guest's proxy QPs followed the
structure of the PPF special qps (qp0 port 1, qp0 port 2, qp1 port 1,
qp1 port 2, ...).  The guest then did offset calculations on the
sqp_base qp number that the PPF passed to it in QUERY_FUNC_CAP().

This is now changed so that the guest does no offset calculations
regarding proxy or tunnel QPs to use.  This change frees the PPF from
needing to adhere to a specific order in allocating proxy and tunnel
QPs.

Now QUERY_FUNC_CAP provides each port individually with its proxy
qp0, proxy qp1, tunnel qp0, and tunnel qp1 QP numbers, and these are
used directly where required (with no offset calculations).

To accomplish this change, several fields were added to the phys_caps
structure for use by the PPF and by non-SR-IOV mode:

    base_sqpn -- in non-sriov mode, this was formerly sqp_start.
    base_proxy_sqpn -- the first physical proxy qp number -- used by PPF
    base_tunnel_sqpn -- the first physical tunnel qp number -- used by PPF.

The current code in the PPF still adheres to the previous layout of
sqps, proxy-sqps and tunnel-sqps.  However, the PPF can change this
layout without affecting VF or (paravirtualized) PF code.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

1. Introduce the basic SR-IOV parvirtualization context objects for
   multiplexing and demultiplexing MADs.
2. Introduce support for the new proxy and tunnel QP types.

This patch introduces the objects required by the master for managing
QP paravirtualization for guests.

struct mlx4_ib_sriov is created by the master only.
It is a container for the following:

1. All the info required by the PPF to multiplex and de-multiplex MADs
   (including those from the PF). (struct mlx4_ib_demux_ctx demux)
2. All the info required to manage alias GUIDs (i.e., the GUID at
   index 0 that each guest perceives.  In fact, this is not the GUID
   which is actually at index 0, but is, in fact, the GUID which is at
   index[<VF number>] in the physical table.
3. structures which are used to manage CM paravirtualization
4. structures for managing the real special QPs when running in SR-IOV
   mode.  The real SQPs are controlled by the PPF in this case.  All
   SQPs created and controlled by the ib core layer are proxy SQP.

struct mlx4_ib_demux_ctx contains the information per port needed
to manage paravirtualization:

1. All multicast paravirt info
2. All tunnel-qp paravirt info for the port.
3. GUID-table and GUID-prefix for the port
4. work queues.

struct mlx4_ib_demux_pv_ctx contains all the info for managing the
paravirtualized QPs for one slave/port.

struct mlx4_ib_demux_pv_qp contains the info need to run an individual
QP (either tunnel qp or real SQP).

Note:  We made use of the 2 most significant bits in enum
mlx4_ib_qp_flags (based on enum ib_qp_create_flags in ib_verbs.h).
We need these bits in the low-level driver for internal purposes.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NDotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Unlike other parts of the mlx4_ib code, the function build_mlx_header()
doesn't check if the iboe netdev of the given port is valid before
dereferencing it, which can cause a crash if the ethernet interface
has already been taken down.

Fix this by checking for a valid netdev pointer before using it to get
the port MAC address.
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Define pr_fmt and add some pr_debug prints.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The driver is modified to support three operation modes.

If supported by firmware use the device managed flow steering
API, that which we call device managed steering mode. Else, if
the firmware supports the B0 steering mode use it, and finally,
if none of the above, use the A0 steering mode.

When the steering mode is device managed, the code is modified
such that L2 based rules set by the mlx4_en driver for Ethernet
unicast and multicast, and the IB stack multicast attach calls
done through the mlx4_ib driver are all routed to use the device
managed API.

When attaching rule using device managed flow steering API,
the firmware returns a 64 bit registration id, which is to be
provided during detach.

Currently the firmware is always programmed during HCA initialization
to use standard L2 hashing. Future work should be done to allow
configuring the flow-steering hash function with common, non
proprietary means.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Limit the max number of WQEs per QP reported when querying the
   device, so that ib_create_qp() will not fail for a QP size that the
   device claimed to support due to additional headroom WQEs being
   allocated.

2. Limit qp resources accepted for ib_create_qp() to the limits
   reported in ib_query_device().  In kernel space, make sure that the
   limits returned to the caller following qp creation also lie within
   the reported device limits. For userspace, report as before, and do
   adjustment in libmlx4 (so as not to break ABI).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NSagi Grimberg <sagig@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NShlomo Pongratz <shlomop@mellanox.com>

[ Replace one more printk_once() with pr_info_once().  - Roland ]
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Otherwise CM packets going over MLX QP1 get fixed scheduling priority 0.
We want CM packets to get the same scheduling priority, and therefore
map to the same SQ (Schedule Queue) and eventually TC (Traffic Class),
as the application requested for the actual QP used for the connection.
Signed-off-by: NOren Duer <oren@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Implement raw packet QPs for Ethernet ports using the MLX transport (as
done by the mlx4_en Ethernet netdevice driver).
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

If the opcode of a work request exceeds the range of valid opcodes,
return the pointer to the offending work request.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

For IBoE, SLs 0-7 are mapped to Ethernet 802.1Q user priority bits
(pbits) which are part of the VLAN tag, SLs 8-15 are reserved.

Under Ethernet, the ConnectX firmware treats (decode/encode) the four
bit SL field in various constructs such as QPC / UD WQE / CQE as PPP0
and not as 0PPP. This correlates well to the fact that within the
vlan tag the pbits are located in bits 15-13 and not 12-14.

The current code wasn't consistent around that area - the
encoding was correct for the IBoE QPC.path.schedule_queue field,
but was wrong for IBoE CQEs and when MLX header was built.

These inconsistencies resulted in wrong SL <--> wire 802.1Q pbits
mapping, which is fixed by using SL <--> PPP0 all around the place.
Signed-off-by: NOren Duer <oren@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

There's no need to set the vlan-related fields in an IBoE send WQE
control segment:

 - the vlan to be used by a UD QP is set in the datagram segment.
 - for GSI (CM) QP, all the headers down to 8021q and MAC are built by
   the software anyway.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Support the creation of XRC INI and TGT QPs.  To handle the case where
a CQ or PD is not provided, we allocate them internally with the xrcd.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Allocate flow counter per Ethernet/IBoE port, and attach this counter
to all the QPs created on that port.  Based on patch by Eli Cohen
<eli@mellanox.co.il>.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

We must fully update the control segment before marking it as valid,
so that hardware doesn't start executing it before we're ready.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>

[ Move VLAN control bit setting to before wmb().  - Roland ]
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch allows IBoE traffic to be encapsulated in 802.1Q tagged
VLAN frames.  The VLAN tag is encoded in the GID and derived from it
by a simple computation.

The netdev notifier callback is modified to catch VLAN device
addition/removal and the port's GID table is updated to reflect the
change, so that for each netdevice there is an entry in the GID table.
When the port's GID table is exhausted, GID entries will not be added.
Only children of the main interfaces can add to the GID table; if a
VLAN interface is added on another VLAN interface (e.g. "vconfig add
eth2.6 8"), then that interfaces will not add an entry to the GID
table.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>