Add a pfc node to the sh73a0 device tree and remove manual pinmux
initialization from the corresponding board files.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The convention for Device Tree node names is <device>@<hex-address>, where
the part after '@' shouldn't contain the "0x" prefix. Fix the sh73a0.dtsi
DT names.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add DT nodes for the 4 irqpin interrupt controllers on sh73a0. We add them
to sh73a0.dtsi, which is also used by configurations, doing all their
device instantiation from board the .c code. We rely on the fact, that
such configurations don't instantiate devices from the device-tree.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Fix several device-tree bindings, that haven't been updated for newest
versions of respective drivers, and device names and pin numbers, left over
from non-DT and old pinctrl versions.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

To avoid having to repeat common DT node properties in all .dts files
move them to SoC's .dtsi file, setting their status to "disabled."
Individual boards will pick up devices, that they want to use and
change their DT node status to enabled.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Allow a minimal setup of the sh73a0 SoC using a flattened device tree.
In particular, Configure the i2c controllers using a flattened device tree.

SCI serial controller and CMT clock source, whose drivers do not yet
support configuration using a flattened device tree, are still configured
using C code in order to allow booting of a board with this SoC.

*** Please note that the clock initialisation scheme used in
    this patch does not currently work with SMP as there
    is a yet to be resolved lock-up in workqueue initialisation.

    CONFIG_SMP must be disabled when using this code. ***

Includes update from Thierry Reding to no longer use gic_handle_irq()

Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

fix

This allows the GIC interrupt controller of the sh73a0 SoC to be
initialised using a flattened device tree blob.

It does not allow the INTC interrupt controller which is also present on
the sh73a0 SoC to be enabled via device tree.  Nor does it handle sharing
of interrupts between the GIC and INTC interrupt controllers.

This limits the usefulness of this code to applications which only wish to
access devices which use interrupts that can be handled by the GIC
interrupt controller. Other applications should, for now, continue using
non-device tree initialisation of the sh72a0 interrupt controllers.

Includes update to use irqchip_init() by Thierry Reding

Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add generic DT board support for the r8a7740 SoC.

SCIF serial ports and timers are kept as regular
platform devices. Other on-chip and on-board devices
should be configured via the device tree.

At this point there is no interrupt controller support
in place but such code will be added over time when
proper IRQ domain support has been added to INTC.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Add generic DT board support for the sh7372 SoC V2.

SCIF serial ports and timers are kept as regular
platform devices. Other on-chip and on-board devices
should be configured via the device tree.

Tested on the mackerel board via kexec using a zImage
kernel with an appended dtb.

At this point there is no interrupt controller support
in place but such code will be added over time when
proper IRQ domain support has been added to INTC.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>