The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
  drivers/net/wireless/ath5k/base.c
  drivers/net/wireless/b43/main.c
  drivers/net/wireless/ipw2100.c
  drivers/net/wireless/ipw2200.c
  drivers/net/wireless/iwlwifi/iwl-3945.c
  drivers/net/wireless/iwlwifi/iwl-4965.c
  drivers/net/wireless/iwlwifi/iwl-5000.c
  drivers/net/wireless/iwlwifi/iwl-agn.c
  drivers/net/wireless/iwlwifi/iwl-core.c
  drivers/net/wireless/iwlwifi/iwl-eeprom.c
  drivers/net/wireless/iwlwifi/iwl-hcmd.c
  drivers/net/wireless/iwlwifi/iwl-power.c
  drivers/net/wireless/iwlwifi/iwl3945-base.c

This patch removes the said #include <version.h>.
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

txdone_entry_desc_flags is used with __set_bit and test_bit which
bit-shift the values, so don't bit-shift the flags in the enum.
Also make sure flags are initialized before being used.
Signed-off-by: NJochen Friedrich <jochen@scram.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In trying to help users on the Ubuntu Bugzilla, I discovered another
BCM4306 with the Bluetooth Coexistence programming error in the SPROM.

This patch is contingent on the one that added the Linksys device with
subdevice code of 0x0014.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

(Only important for USB V1 Adaptors)

If an incoming frame wasn't accepted by p54_rx function
the skb will be reused for new frames...

But, we must not forget to set the skb's data pointers into
the same state in which it was initialized by p54u_init_urbs.

Otherwise we either end up with 16 bytes less on every requeue,
or if a new frame is worthy enough to be accepted, the data is
in the wrong place (urb->transfer_buffer wasn't updated!) and mac80211
has a hard time to recognize it...
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

priv->tx_hdr_len is set by the driver _after_ it called p54_init_common.
While this isn't much a problem for any PCI or ISL3887 cards/sticks,
because they don't need any extra header and therefore tx_hdr_len is
zero for them...
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add newlines at printk outputs to not break dmesg.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the USB ID for a Netgear WG111v3.
Signed-off-by: Nmatthieu Barthélemy <bonsouere@gmail.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Linksys WMP54G (BCM4306/3) card in a PCI format has an SPROM coding
error and needs the fix found for several other cards.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>		[2.6.25.x, 2.6.26.x]
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 256b152b (ath5k: don't enable
MSI, we cannot handle it yet) has removed msi support, but overlooked
the suspend/resume code. This patch completes msi removal.

I don't consider this patch copyrightable, and thus put it into the
public domain. The result is of course a base.c file dual-licensed under
3-clause-BSD and GPL.
Signed-off-by: NMichael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit b19fa1fa, entitled "net: Delete NETDEVICES_MULTIQUEUE kconfig
option" breaks p54pci and p54usb.

Additionally, the old logic always tx'ed cts frames (if enabled)
with a short preamble when [rate > 3]. (i.e. with any 802.11g rate).
Of course this isn't that bad, but it's still wrong!

(This patch also clarifies the meanings of some of the fields in the tx
header for the hardware. -- JWL)
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: <stable@kernel.org>		[2.6.25.x, 2.6.26.x]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

(I missed the fact that the original post said to apply this patch
twice... -- JWL)

Original commit log message:

This patch works around an internal compiler error (gcc bug #37014) in
all gcc 4.2 compilers and the gcc 4.3 series up to at least 4.3.1
on at least powerpc and mips.

Many thanks to Andrew Pinski for analyzing the gcc bug.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use a single enum for managing modes, store supported modes by
the HW in a bitmask.
Register legacy rates with mac80211 only at init.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use ath9k_tx_queue_info which contains the same elements,
and merge get/set functions of tx queue properties.
Also, fix whitespace damage in struct ath_softc.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch works around an internal compiler error (gcc bug #37014) in
all gcc 4.2 compilers and the gcc 4.3 series up to at least 4.3.1
on at least powerpc and mips.

Many thanks to Andrew Pinski for analyzing the gcc bug.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds the new mac80211 11n ath9k Atheros driver. Only STA support
is currently enabled and tested.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove Atheros 11n devices from being claimed by ath5k as its
now handled by ath9k.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

these "magic" values must to be the other way round...
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It was possible for unsupported operating modes
to be accepted by the add_interface callback function.
This patch will block those modes until proper support
has been implemented for them.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Following "mac80211: fix TX sequence numbers", if a packet
has the IEEE80211_TX_CTL_ASSIGN_SEQ assigned, a sequence number must be
supplied, either by hardware or software. AFAIK, no such hardware exists
for the p54, thus it must be done in software. With this patch, a connection
qith p54usb is stable, whereas the interface went off-line in 2-3 hours
without this change. Note that this code will have to be reworked for proper
sequence numbers on beacons. In addition, the sequence number has been placed
in the hardware state, not the vif state.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up iwl_tx_skb function.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some hardware set promisc when they are requested to set IFF_ALLMULTI flag.
It's ok, but if drivers set IFF_PROMISC flag when they set promisc,
it will broken upper layer handle for promisc and allmulti.
In addition, drivers can use their own hardware programming to make it.
So do not allow drivers to set IFF_* flags.

This is a general driver fix, so I didn't split it to pieces and send
to specific driver maintainers.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We should allow packets transmission in monitor mode for 3945. The
patch fixes a merge error with 2.6.26 kernel.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We need to grap nic access before accessing periphery registers.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch decrements rx skb counter in scan abort handler.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes unhandled interrupt when HW rfkill is on during
devices start up. The behavior changes, now open is successful even
when rfkill is on. This is to align with the situation when rfkill
is set on after opening.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch implements rssi calculation for 5000 HW.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch optimizes memory allocation. The cmd member of
iwl_tx_queue was allocated previously as a continuous block
of memory. This patch allocates separate memory chunks for each command
and maps/unmaps these chunks in the run time.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds few HW bug fixes.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Experience with the rtl8187 driver has shown that mac80211 can make
calls to the config callback routine in rapid succession. This patch
creates a mutex that protects the private data in several of the routines
called by mac80211.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the legacy rt2570 driver the link tuner was never
really called. And now the reason has finally become
apparent: It breaks TX capabilities

As soon as the device has been associated all following
TX frames will be queued in the hardware and never transmitted
to the air. Disabling sections of the link tuner did not
have the expected result, but completely disabling the
link tuner did have the right result (Both of my rt2570 devices
came back to life).

This should fix Fedora bug: 411481

v2: Fix typos
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Having the buffer on the stack and even re-using it for all led devices is bad.
Not being able to resolve the name member of the led device structure to a
meaningful value leads to confusion during ad-hoc debugging and potential
breakage in the future, if we ever decide to access the name member outside of
the registration function. Move the buffer to our private per led device
structures so that it is accessible after registration.

A quick grep didn't yield any occurence of using the led device name parameter
outside of the led device registration function, so currently we should already
be safe for normal operation.
Signed-off-by: NSven Wegener <sven.wegener@stealer.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch renames driver name from 4965 to AGN
The driver supports both 4965AGN and 5000AGN family

The driver's original module name iwl4965.ko remains as an alias
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes errors reported by checkpatch in iwlwifi drivers
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch renames iwl4965-base.c to iwl-agn.c
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch uses dtim_period from association, and sets the listen_interval.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl-agn-rs.c: In function 'rs_clear':
iwl-agn-rs.c:2405: warning: unused variable 'priv
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>