For GPIOs of gpio-lpc32xx, gpio_direction_output() ignores the value argument
(initial value of output). This patch fixes this by setting the level
accordingly.

Cc: stable@kernel.org
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Acked-by: NAlexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch helps mapping with gpio_to_irq for the GPIOs that are irq enabled.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Tested-by: NAlexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Since LPC32xx is now switched over to devicetree based GPIO, the unused
lpc32xx_gpio_init() can be removed.

Further, the driver title changed since it referred to the wrong file.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds device tree support for gpio-lpc32xx.c.

To register the various GPIO banks as (struct) gpio_chips via the same DT
gpio-controller, we utilize the adjusted of_xlate API to manipulate the
actually used struct gpio_chip.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The chip offers the function to detect the current state of output of the GPO
P3 pins. Useful for reading GPIO output state in Linux' GPIO API, e.g. via
sysfs.

Please note that this only reads back the currently programmed output state,
not the actual electrical level in terms of a GPI function. Finally, GPO3 is
still just an output.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add missing mask to pin bit selection in gpio-lpc32xx.c
(#define GPIO3_PIN_IN_SEL)
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

One of the GPIO names in drivers/gpio/gpio-lpc32xx.c
was bad. Renaming gpi000 -> gpio00
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.

Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Barry Song <bs14@csr.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As per example from the other ARM boards, push the LPC32XX
GPIO driver down to the GPIO subsystem so it can be consolidated.

Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Barry Song <bs14@csr.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Common drivers for the LPC32XX used on all platforms
Signed-off-by: NKevin Wells <wellsk40@gmail.com>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>