Add dev->ap which points back to the port the device belongs to.  This
makes it unnecessary to pass @ap for silly reasons (e.g. printks).
Also, this change is necessary to accomodate later PM support which
will introduce ATA link inbetween port and device.
Signed-off-by: NTejun Heo <htejun@gmail.com>

Kill now unused scr_{read|write|write_flush}() and sata_dev_present().
Signed-off-by: NTejun Heo <htejun@gmail.com>

Implement ata_scr_{valid|read|write|write_flush}() and
ata_port_{online|offline}().  These functions replace
scr_{read|write}() and sata_dev_present().

Major difference between between the new SCR functions and the old
ones is that the new ones have a way to signal error to the caller.
This makes handling SCR-available and SCR-unavailable cases in the
same path easier.  Also, it eases later PM implementation where SCR
access can fail due to various reasons.

ata_port_{online|offline}() functions return 1 only when they are
affirmitive of the condition.  e.g.  if SCR is unaccessible or
presence cannot be determined for other reasons, these functions
return 0.  So, ata_port_online() != !ata_port_offline().  This
distinction is useful in many exception handling cases.
Signed-off-by: NTejun Heo <htejun@gmail.com>

Add qc->result_tf and ATA_QCFLAG_RESULT_TF.  This moves the
responsibility of loading result TF from post-compltion path to qc
execution path.  qc->result_tf is loaded if explicitly requested or
the qc failsa.  This allows more efficient completion implementation
and correct handling of result TF for controllers which don't have
global TF representation such as sil3124/32.
Signed-off-by: NTejun Heo <htejun@gmail.com>

It's not a very good idea to allocate memory during EH.  Use
statically allocated buffer for dev->id[] and add 512byte buffer
ap->sector_buf.  This buffer is owned by EH (or probing) and to be
used as temporary buffer for various purposes (IDENTIFY, NCQ log page
10h, PM GSCR block).
Signed-off-by: NTejun Heo <htejun@gmail.com>

Kill duplicate prototypes for ata_eh_qc_complete/retry() in libata.h.
Signed-off-by: NTejun Heo <htejun@gmail.com>

Rename ata_down_sata_spd_limit() and friends to sata_down_spd_limit()
and likewise for simplicity & consistency.
Signed-off-by: NTejun Heo <htejun@gmail.com>

This will be used by LLDD hardreset implementation.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

As waiting for some register bits to change seems to be a common
operation shared by some controllers, implement helper function
ata_wait_register().  This function also takes care of register write
flushing.

Note that the condition is inverted, the wait is over when the masked
value does NOT match @val.  As we're waiting for bits to change, this
test is more powerful and allows the function to be used in more
places.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

@verbose was added to ata_reset_fn_t because AHCI complained during
probing if no device was attached to the port.  However, muting
failure message isn't the correct approach.  Reset methods are
responsible for detecting no device condition and finishing
successfully.  Now that AHCI softreset is fixed, kill @verbose.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Overriding the whole EH code is a per-transport, not per-host thing.
Move ->eh_strategy_handler to the transport class, same as
->eh_timed_out.

Downside is that scsi_host_alloc can't check for the total lack of EH
anymore, but the transition period from old EH where we needed it is
long gone already.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Convert the ATAPI_ENABLE_DMADIR compile time option needed
by some SATA-PATA bridge to runtime module parameter.
Signed-off-by: NAlbert Lee <albertcc@tw.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

A lot of EH codes are about to be added to libata.  Separate out
libata-eh.c.  ata_scsi_timed_out(), ata_scsi_error(),
ata_qc_timeout(), ata_eng_timeout(), ata_eh_qc_complete() and
ata_eh_qc_retry() are moved.  No code is changed by this patch.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add a new qc flag ATA_QCFLAG_IO.  This flag gets set for normal IO
commands originating from SCSI midlayer.  This information will be
used by EH to determine transfer speed reconfiguration.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_dev_configure() should not clear dynamic device flags determined
elsewhere.  Lower eight bits are reserved for feature flags, define
ATA_DFLAG_CFG_MASK and clear only those bits before configuring
device.  Without this patch, ATA_DFLAG_PIO gets turned off during
revalidation making PIO mode unuseable.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Rename ATA_FLAG_PORT_DISABLED to ATA_FLAG_DISABLED for consistency.
(ATA_FLAG_* are always about ports).
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* Reorder ATA_DFLAG_* such that feature flags determined by
  ata_dev_configure() are on lower bits.  Reserve lower eight bits
  for this purpose and allocate dynamic flags from bit 8.

* Reorder ATA_FLAG_* such that feature flags determined during driver
  initiailization are on bits 0:15, dynamic flags on 16:23 and LLDD
  specific flags on 24:31.

* Kill trailing white space and lower-case an one line comment for
  consistency.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Kill unused flag ATA_FLAG_IN_EH.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Improve ata_bus_probe() such that configuration failures are handled
better.  Each device is given ATA_PROBE_MAX_TRIES chances, but any
non-transient error (revalidation failure with -ENODEV, configuration
failure with -EINVAL...) disables the device directly.  Any IO error
results in SATA PHY speed down and ata_set_mode() failure lowers
transfer mode.  The last try always puts a device into PIO-0.

After each failure, the whole port is reset to make sure that the
controller and all the devices are in a known and stable state.  The
reset also applies SATA SPD configuration if necessary.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ap->sata_spd_limit contrains SATA PHY speed of the port.  It is
initialized to the configured value prior to probing thus preserving
BIOS configured value.  hardreset is responsible for applying SPD
limit and sata_std_hardreset() is updated to do that.  SATA SPD limit
will be used to enhance failure handling during probing and later by
EH.

This patch also normalizes some comments around affected code.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

For the time being we cannot use ata_dev_present() as it was renamed
to ata_dev_enabled() but we still need presence test.  Implement
negation of the test.  Conveniently, the negated result is needed in
more places.  This is suggested by Jeff Garzik.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch renames ata_dev_present() to ata_dev_enabled() and adds
ata_dev_disabled().  This is to discern the state where a device is
present but disabled from not-present state.  This disctinction is
necessary when configuring transfer mode because device selection
timing must not be violated even if a device fails to configure.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add a field to the host_set called 'flags' (was host_set_flags changed
to suit Jeff)
Add a simplex_claimed field so we can remember who owns the DMA channel
Add a ->mode_filter() hook to allow drivers to filter modes
Add docs for mode_filter and set_mode
Filter according to simplex state
Filter cable in core

This provides the needed framework to support all the mode rules found
in the PATA world. The simplex filter deals with 'to spec' simplex DMA
systems found in older chips. The cable filter avoids duplicating the
same rules in each chip driver with PATA. Finally the mode filter is
neccessary because drive/chip combinations have errata that forbid
certain modes with some drives or types of ATA object.

Drive speed setup remains per channel for now and the filters now use
the framework Tejun put into place which cleans them up a lot from the
older libata-pata patches.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Some hardware doesn't want the usual mode setup logic running. This
allows the hardware driver to replace it for special cases in the least
invasive way possible.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This is the minimal patch set to enable the current code to be used with
a controller following SFF (ie any PATA and early SATA controllers)
safely without crashes if there is no BMDMA area or if BMDMA is not
assigned by the BIOS for some reason.

Simplex status is recorded but not acted upon in this change, this isn't
a problem with the current drivers as none of them are for simplex
hardware. A following diff will deal with that.

The flags in the probe structure remain ->host_set_flags although Jeff
asked me to rename them, simply because the rename would break the usual
Linux rules that old code should break when there are changes. not
compile and run and then blow up/eat your computer/etc. Renaming this
later is a trivial exercise once a better name is chosen.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

E.D.D. has no user in-tree and mostly useless.  Kill it.  For possible
out-of-tree users, add a nice warning message and error handling if
LLDD doesn't report any useable reset mechanism (and thus tries to use
E.D.D.).
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove some of the dependence on the host_set struct
in preparation for supporting SAS HBAs. Adds a struct device
pointer to the ata_port struct.
Signed-off-by: NBrian King <brking@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

At the moment libata doesn't pass pm_message_t down ata_device_suspend.
This causes drives to be powered down when we just want a freeze,
causing unnecessary wear and tear. This patch gets pm_message_t passed
down so that it can be used to determine whether to power down the
drive.
Signed-off-by: NNigel Cunningham <nigel@suspend2.net>

 drivers/scsi/libata-core.c |    5 +++--
 drivers/scsi/libata-scsi.c |    4 ++--
 drivers/scsi/scsi_sysfs.c  |    2 +-
 include/linux/libata.h     |    4 ++--
 include/scsi/scsi_host.h   |    2 +-
 5 files changed, 9 insertions(+), 8 deletions(-)
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add per-dev pio/mwdma/udma_mask.  All transfer mode limits used to be
applied to ap->*_mask which unnecessarily restricted other devices
sharing the port.  This change will also benefit later EH speed down
and hotplug.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add prototypes for stuff recently added by Alan.

Add some dummy noop functions for use by libata clients
that do not need to do anything. Future SAS patches will
utilize these functions.
Signed-off-by: NBrian King <brking@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

SCSI midlayer has moved hostt->eh_timed_out to transport template.  As
libata doesn't need full-blown transport support yet, implement
minimal transport for libata.  No transport class or whatsoever, just
empty transport template with ->eh_timed_out hook.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Add ATA_BITS_*, ATA_MASK_* macros and reorder xfer_mask fields such
that higher transfer mode is placed at higher order bit.  As thie
reordering breaks ata_mode_string(), this patch also rewrites
ata_mode_string().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Rename ATA_FLAG_FLUSH_PIO_TASK to ATA_FLAG_FLUSH_PORT_TASK.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Kill unused pio_task and packet_task.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Implement port_task.  LLDD's can schedule a function to be executed
with context after specified delay.  libata core takes care of
synchronization against EH.  This is generalized form of pio_task and
packet_task which are tied to PIO hsm implementation.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_dev_revalidate() re-reads IDENTIFY PAGE of the given device and
makes sure it's the same device as the configured one.  Once it's
verified that it's the same device, @dev is configured according to
newly read IDENTIFY PAGE.  Note that revalidation currently doesn't
invoke transfer mode reconfiguration.

Criteria for 'same device'

* same class (of course)
* same model string
* same serial string
* if ATA, same n_sectors (to catch geometry parameter changes)
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>