The convention for pci_driver.name entry in kernel drivers seem to be
the module name or equivalent ones.  But, so far, almost all PCI sound
drivers use more verbose name like "ABC Xyz (12)", and these are fairly
confusing when appearing as a file name.

This patch converts the all pci_driver.name entries in sound/pci/* to
use KBUILD_MODNAME for more unified appearance.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add a mixer control to switch between the optical and coaxial S/PDIF
inputs on the HT-Omega Claro and Claro halo cards.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Enable the X-Meridian's CD input and the X-Meridian 2G's potential
MIDI ports.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Instead of the generic Oxygen, use the actual card name, if known.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add a mixer control to select between the on-board and extension board
S/PDIF inputs for the X-Meridian (2G).
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Introduce the helper function snd_ctl_enum_info() to fill out the
elem_info fields for an enumerated control.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add experimental support for the Asus Xonar DG sound card.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add support for the AuzenTech X-Meridian 7.1 2G sound card.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add PCI IDs for some unknown models.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For the CSxxxx and AKxxxx DAC/ADC chips, the MCLK factor in double rate
modes (64-96 kHz) can be reduced to 128x without reducing sound quality.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Replace the get_i2s_mclk callback with tables of MCLK values.  This
simplifies the MCLK-handling code in both the framework and the model-
specific drivers.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For cards like the Xonar HDAV1.3, differentiate between the number of
PCM channels that can be played and the number of channels whose volume
can be adjusted.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Reformat and update the comments that describe the hardware connections
on the various models.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

To help with debugging, add the registers of the model-specific
codecs to the controller and AC97 register dump in the proc file.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add support for the TempoTec/MediaTek HiFier Serenade sound card.

The PCI ID was already there, but the driver handled it like the
Fantasia model, which resulted in a dummy recording device.  As
a stereo output-only card, this model is to be handled exactly
like the HG2PCI.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Sort the PCI IDs so that they make logical sense.  Also move the card
name comments into this list because the model symbols should be (more)
self-explanationary.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add support for the Kuroutoshikou CMI8787-HG2PCI sound card.

[replaced non-latin letters in the patch by tiwai]
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The snd-hifier driver contains more duplicated code than model-specific
code, so it does not make sense for it to be a separate driver.
Handling the two-channel output restriction can be easily done in the
generic driver.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This board has a strange PCI SSID 13f6:ffff.  Works as compabile as
MODEL_CMEDIA_REF.
Reported-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

There are more models without a CD input than with one, so handle this
explicitly with a device_config flag to avoid having to define a control
filter callback to filter it out.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

On the HT-Omega Claro halo card, the ADC data must be captured from the
second I2S input.  Using the default first input, which isn't connected
to anything, would result in silence.
Signed-off-by: NErik J. Staab <ejs@insightbb.com>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use DEFINE_PCI_DEVICE_TABLE() to make PCI device ids go to
.devinit.rodata section, so they can be discarded in some cases,
and make them const.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add a control that allows disabling the high-pass filter of the WM8785 ADC.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add a control to select between sharp and slow roll-of filter responses
of the DACs.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add a callback that allows model drivers to modify the default I2S MCLK
rate.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Keep a cache of codec registers to avoid unnecessary writes.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add some comments describing the hardware pin routing.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

On the HT-Omega Claro (halo) sound cards, the headphone amplifier must
be enabled explicitly by setting a GPIO bit.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The HT-Omega Claro halo's ADC is an AK5385 instead of a WM8785, so we
should handle the ADC parameters as we do with the X-Meridian.

Using the code for the wrong ADC does not seem to have any audible
effects, and the Windows driver does it, but it is nonetheless a good
idea to run the AK5385 with an oversampling ratio that is not outside
the documented limits.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Under as yet unknown circumstances, the first word of the sound card's
EEPROM gets overwritten.  When this has happened, we cannot rely on the
subsystem IDs that the kernel reads from the PCI configuration
registers.  Instead, we read the IDs directly from the EEPROM and do the
ID matching manually.

Because the model-specific driver cannot determine the model before
calling oxygen_pci_probe(), that function now gets a get_model()
callback as parameter.  The customizing of the model structure, which
was formerly done by the probe() callback, also has moved into
get_model().
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Move the owner field out of the oxygen_model structure and make it
a parameter of oxygen_pci_probe(), because the actual owner module does
not depend on the card model.  Furthermore, moving it out of the model
structure allows us to create the card structure before the actual model
is known.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add support for the HT-Omega Claro halo (XT).
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Introduce some trivial functions to better document the relationships of
the various model callbacks.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

To enable the MIDI port, model drivers must now set flags in
device_config, not only in misc_flags.  This allows model drivers to
enable the UART without creating an ALSA MIDI device.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Rename the pcm_dev_cfg field to device_config because there will be
additional flags that do not describe PCM devices.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Handle the differences between the X-Meridian and the other models in
the probe callback instead of using a second model structure.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Introduce symbols that indicate the two models handled by the snd-oxygen
driver, instead of using a magic number.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Add a probe callback to the model structure so that model-specific
drivers can refine their model detection before the card is initialized.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

When changing the sample rate, the CMI8788's master clock output becomes
unstable for a short time.  The AK4396 needs the master clock to do SPI
writes, so writing to an AK4396 control register directly after a sample
rate change will garble the value.  In our case, this leads to the DACs
being misconfigured to I2S sample format, which results in a wrong
output level and horrible distortions on samples louder than -6 dB.

To fix this, we need to wait until the new master clock signal has
become stable before doing SPI writes.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add suspend/resume support.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>