we save the l2x0 registers at the first initialization, and platform codes
can get them to restore l2x0 status after wakeup.

Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Reviewed-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This adds probing for ARM L2x0 cache controllers via device tree. Support
includes the L210, L220, and PL310 controllers. The binding allows setting
up cache RAM latencies and filter addresses (PL310 only).
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NBarry Song <21cnbao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fighting unfixed U-Boots and other beasts that may the cache in
a locked-down state when starting the kernel, we make sure to
disable all cache lock-down when initializing the l2x0 so we
are in a known state.

Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Adrian Bunk <adrian.bunk@movial.com>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: NJan Rinze <janrinze@gmail.com>
Tested-by: NRobert Marklund <robert.marklund@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch fixes L2 Cache size calculations for L2C-210, L2C-310 and
PL310, by changing the L2X0_AUX_CTRL_WAY_SIZE_MASK from 2 bits to 3
bits.

The Auxiliary Control Register for L2C-210, L2C-310 and PL310 has 3bits
[19:17] for Way size, however the existing code only uses 2 bits to
get this value. This results in incorrect cachesize calculations.

It also results in performing operations on the whole cache when we
erroneously decide that the range is big enough (due to l2x0_size being
too small) and also prints incorrect cachesize.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Cc: stable@kernel.org
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rather than marking the mach/gpio.h header files which want to use the
trivial GPIOLIB implementation, mark those which do not want to use it
instead.  This means that by default, you get the trivial implementation
and only have to do something extra if you need to.  This should
encourage the use of the trivial default implementation.

As an additional bonus, several gpio.h header files become empty.
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Aside of the usual motivation for constification,  this function has a
history of being abused a hook for interrupt and other fixups so I turned
this function const ages ago in the MIPS code but it should be done
treewide.

Due to function pointer passing in varous places a few other functions
had to be constified as well.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
To: Anton Vorontsov <avorontsov@mvista.com>
To: Chris Metcalf <cmetcalf@tilera.com>
To: Colin Cross <ccross@android.com>
Acked-by: N"David S. Miller" <davem@davemloft.net>
To: Eric Miao <eric.y.miao@gmail.com>
To: Erik Gilling <konkers@android.com>
Acked-by: NGuan Xuetao <gxt@mprc.pku.edu.cn>
To: "H. Peter Anvin" <hpa@zytor.com>
To: Imre Kaloz <kaloz@openwrt.org>
To: Ingo Molnar <mingo@redhat.com>
To: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
To: Jesse Barnes <jbarnes@virtuousgeek.org>
To: Krzysztof Halasa <khc@pm.waw.pl>
To: Lennert Buytenhek <kernel@wantstofly.org>
To: Matt Turner <mattst88@gmail.com>
To: Nicolas Pitre <nico@fluxnic.net>
To: Olof Johansson <olof@lixom.net>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
To: Richard Henderson <rth@twiddle.net>
To: Russell King <linux@arm.linux.org.uk>
To: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-alpha@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-pci@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Since Samsung EXYNOS4210 cannot support register banking in GIC,
so needs to update CPU interface base address.
The 'gic_chip_data' is used for it, this patch moves gic_chip_data
structure declaraton to arch/arm/include/asm/hardware/gic.h to use
it.

Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NChanghwan Youn <chaos.youn@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

A pcmcia_init callback isn't used on any of the platforms. Drop it.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This allows platforms to specify the clcokevent name upon registration.
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This allows platforms to specify the clocksource name upon
registration, which is necessary should they wish to register more
than one sp804 clocksource.
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Few architectures combine the GIC with an external interrupt
controller. On such systems it may be necessary to update both
the GIC registers and the external controller's registers to control
IRQ behavior.

This can be addressed in couple of possible methods.
 1. Export common GIC routines along with 'struct irq_chip gic_chip'
    and allow architectures to have custom function by override.
 2. Provide architecture specific function pointer hooks
    within GIC library and leave platforms to add the necessary
    code as part of these hooks.

First one might be non-intrusive but have few shortcomings like arch
needs to have there own custom gic library. Locks used should be
common since it caters to same IRQs etc. Maintenance point of view
also it leads to multiple file fixes.

The second probably is cleaner and portable. It ensures that all the
common GIC infrastructure is not touched and also provides archs to
address their specific issue.

Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NColin Cross <ccross@android.com>
Tested-by: NColin Cross <ccross@android.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

In sysctl_soft_reset(), switch to slow mode before resetting the system
via the system controller.  This is required.
Reviewed-by: NStanley Miao <stanley.miao@windriver.com>
Signed-off-by: NShiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The effect of cache sync operation is to drain the store buffer and
wait for all internal buffers to be empty. In normal conditions, store
buffer is able to merge the normal memory writes within its 32-byte
data buffers.  Due to this erratum present in r3p0, the effect of cache
sync operation on the store buffer still remains when the operation
completes. This means that the store buffer is always asked to drain
and this prevents it from merging any further writes.

This can severely affect performance on the write traffic esp. on
Normal memory NC one.

The proposed workaround is to replace the normal offset of cache sync
operation(0x730) by another offset targeting an unmapped PL310
register 0x740.
Signed-off-by: Nsrinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Timers on Versatile Express mainboard are used as system clock/event
sources. Driver assumes that they are clocked with 1MHz signal.
Old V2M firmware apparently configured it by default, but on newer
boards one can observe that "sleep 1" command takes over 30 seconds
to finish, as the timers are fed with 32kHz instead...

This patch performs required magic and also removes code clearing
timer's control registers, as exactly the same operations are
performed by the timer driver few jiffies later.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Tested-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The commit 6ac6b817 (ARM: pxa: encode
IRQ number into .nr_irqs) removed definition of ITE_LAST_IRQ which
caused the following build error:

CC      arch/arm/common/it8152.o
arch/arm/common/it8152.c: In function 'it8152_init_irq':
arch/arm/common/it8152.c:86: error: 'IT8152_LAST_IRQ' undeclared (first use in this function)
arch/arm/common/it8152.c:86: error: (Each undeclared identifier is reported only once
arch/arm/common/it8152.c:86: error: for each function it appears in.)
make[2]: *** [arch/arm/common/it8152.o] Error 1

Defining the IT8152_LAST_IRQ in the arch/arm/include/hardware/it8152.c
fixes the build.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch adds the PL310 Auxiliary Control Register bitfields
so that SOC's can use these bit fields to construct the AUXCTRL
value to be passed/programmed instead of hardcoding it.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Avoid adding nasty genirq-specific code to local timers to enable PPI
interrupts.  Instead, provide a gic function to do this.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Provide a standard get_irqnr_preamble assembler macro for platforms
to use, which retrieves the base address of the GIC CPU interface
from gic_cpu_base_addr.  Allow platforms to override this by defining
HAVE_GET_IRQNR_PREAMBLE.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Tested-by: NAbhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Every architecture using the GIC has a gic_cpu_base_addr pointer for
GIC 0 for their entry assembly code to use to decode the cause of the
current interrupt.  Move this into the common GIC code.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Tested-by: NAbhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We don't need to re-pass the base address for the CPU interfaces to the
GIC for secondary CPUs, as it will never be different from the boot CPU
- and even if it was, we'd overwrite the boot CPU's base address.

Get rid of this argument, and rename to gic_secondary_init().
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Tested-by: NAbhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Provide gic_init() which initializes the GIC distributor and current
CPU's GIC interface for the boot (or single) CPU.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Tested-by: NAbhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch is the identical GIC demux implementation
merge V3. Instead of implementing same code over and
over simply share it in entry-macro-gic.S. The shared
code is based on the realview implementation.

Each GIC demux instance still has to setup the base address
of the controller using the get_irqnr_preamble macro. The
rest of the GIC specific code can be shared.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

From: Rob Herring <rob.herring@smooth-stone.com>

The timer-sp h/w used on versatile platforms can also be used for other
platforms, so move it to a common location.
Signed-off-by: NRob Herring <rob.herring@smooth-stone.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Mike Rapoport <mike@compulab.co.il>

The cache size is needed for to optimise range based
maintainance operations
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>

Replace tab with space after #define to be consisten with other
define in the file. Also move the bit mask below the register offsets.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>

This patch adds L2X0 Prefetch and Power control register.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The patch below updates broken web addresses in the arch directory.
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Reviewed-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Use BIT() macro whenever it is sensible to do so.

Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAlexander Shishkin <virtuoso@slind.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is done so as to be able to make use of the coresight components'
registers in assembler code (like omap sleep code). Also, there shouldn't
be any users of this structure outside the etm driver.

Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAlexander Shishkin <virtuoso@slind.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This PL008 among all other variables named PL080 doesn't seem
right. Fix it. Also add some missing defined that I use in the
new PL08x driver.
Acked-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add notion of ETM OS lock, save and restore registers.

Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAlexander Shishkin <virtuoso@slind.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add bit definitions of the CPR register of the SCOOP chip into scoop.h. Also,
cleanup the GPCR definitions to match coding style.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

PL330 is a configurable DMA controller PrimeCell device.
The register map of the device is well defined.
The configuration of a particular implementation can be
read from the six configuration registers CR0-4,Dn.

This patch implements a driver for the specification:-
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0424a/DDI0424A_dmac_pl330_r0p0_trm.pdf

The exported interface should be sufficient to implement
a driver for any DMA API.
Signed-off-by: NJassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The L310 cache controller's interface is almost identical
to the L210. One major difference is that the PL310 can
have up to 16 ways.

This change uses the cache's part ID and the Associativity
bits in the AUX_CTRL register to determine the number of ways.

Also, this version prints out the CACHE_ID and AUX_CTRL registers.
Acked-by: NWill Deacon <will.deacon@arm.com>
Acked-by: NAcked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NJason S. McMullan <jason.mcmullan@netronome.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The only difference between ICST307 and ICST525 are the two arrays
for calculating the S parameter; the code is now identical.  Merge
the two files and kill the duplicated code.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This makes the ICST support fit more nicely with the clk API,
eliminating the need to *1000 and /1000 in places.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>