Remove unnecessary Kconfig entry. S5PC100 has exactly the same driver as
S3C6400/S3C6410/S5P6440.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

UARTs in the S3C2416 are almost same as in S3C2443 and can be handled by
s3c2440 serial driver.
Signed-off-by: NYauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

MFD_TIMBERDALE doesn't appear to be defined anywhere. However the code in
question can build happily without platform specifics so remove the check
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fit blackfin uart over sport driver into common uart inftrastructure.  It
is based on the early platform interfaces to get the platform data early
when the console is initilized.

1. Enable sport uart driver to change uart baud, data bit, stop bit at
   runtime.  Bind the index of uart device nodes to physical index of
   sports.

2. Move all platform data into arch specific board files.  Register
   and probe platform device data in both early and normal stages.

3. Console is registered in sport uart driver as well.

4. Remove 500 us block waiting in sport tx stop code by putting a
   dummy data into tx fifo to make sure the sport tx stops when all bytes
   are shifted out except for the dummy data.

5. clean up a bit and fix up coding style.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Bryan Wu <cooloney@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Support using DMA for sending and receiving data over SCI(F) interfaces of
various SH SoCs.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add platform driver support to the pmac-zilog driver, for m68k macs.
Place the powermac-specific code inside #ifdef CONFIG_PPC_PMAC.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

The recent changes in the UART code mean that we need to ensure that
the 4 UART case is only selected if S5PV210 is being compiled.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch adds UART serial port support for S5P6442.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support for ARM-based SH-Mobile CPUs to the sh-sci driver.

Also remove the SCLSR register that is missing on sh772x, sh7705 and
SH-Mobile.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

As part of the development process, it is hoped PLAT_S3C is either removed
from all of the PLAT_SAMSUNG derived platforms or removed entirely. It is
also better to use PLAT_SAMSUNG as this is the current base of all Samsung
devices.

Change the two places that use PLAT_S3C to use PLAT_SAMSUNG
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add SERIAL_SAMSUNG_UARTS_4 to mop up the number of cases currently using
four Samsung compatible UARTS.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch adds UART serial port support for S5PV210.
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch adds UART serial port support for S5P6440 CPU. Most of the
serial support of Samsung's 6400 CPU is reused for 6440 CPU.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The sh-sci code conditionalized the clock framework support in order to
give the other platforms a chance to catch up. sh64 supported this some
time ago and the forthcoming ARM changes handle this as well, this leaves
h8300 as the odd one out. H8300 has had since 2.5 to merge it's sh-sci
support upstream, and has yet to do so. At this point I will no longer be
holding back the driver to support an unreponsive architecture, 7 years
is quite enough of a grace period. Support is easily implemented on the
architecture if and when it ever decides to merge its changes upstream.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds support for the APBUART serial port from Aeroflex
Gaisler's IP library GRLIB. It is currently used in all LEON3 designs
(SPARC V8) but can be used on other platforms as well (which support OF).
Signed-off-by: NKristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some configurations of the Timberdale FPGA has the uartlite
included.
Signed-off-by: NRichard Röjfors <richard.rojfors@mocean-labs.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMaxime Bizon <mbizon@freebox.fr>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Serial driver of S5PC100 is the same as S3C6400, so S5PC100 shares the serial
driver with S3C6400. Uart driver is copied from plat-s3c64xx to plat-s5pc1xx,
as I do not use plat-s3c64xx directory.
Signed-off-by: NByungho Min <bhmin@samsung.com>
[ben-linux@fluff.org: title fixup]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The typo causes drivers/serial/s3c6400.c not being built for s3c6400 platform.
Signed-off-by: NRamax Lo <ramaxlo@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Signed-off-by: NBrian Swetland <swetland@google.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

for calculation of numerator and denominator
used in baud rate setting, use generic library function
for optimum settings.
Signed-off-by: NOskar Schirmer <os@emlix.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Driver for the UART found in the Timberdale FPGA
Signed-off-by: NRichard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Depend on KGDB_SERIAL_CONSOLE being set to N rather than !Y, since it can
be built as a module.
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Both software emulated and hardware based CTS and RTS are enabled in
serial driver.

The CTS RTS PIN connection on BF548 UART port is defined as a modem
device not as a host device.  In order to test it under Linux, please
nake a cross UART cable to exchange CTS and RTS signal.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

(akpm: queued pending confirmation of the new major number)

[randy.dunlap@oracle.com: select SERIAL_CORE]
Signed-off-by: NChristian Pellegrin <chripell@fsfe.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enable third UART on BF538/9
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMatt LaPlante <kernel1@cyberdogtech.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Reviewed-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NJohn Linn <john.linn@xilinx.com>
Acked-by: NStephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: NJohn Williams <john.williams@petalogix.com>
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

Enabled serial UART driver for PNX833X devices.
Signed-off-by: NIhar Hrachyshka <ihar.hrachyshka@gmail.com>
Signed-off-by: NAlan Cox <number6@the-village.bc.nu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Always set CONFIG_SERIAL_SAMSUNG_UARTS when building any
of the S3C platforms as even if the driver is not selected
there it is still the facility for the machine files to
register configuration data for the possibility of the
driver being built.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support for the nwp serial device which is connected to a DCR bus. It
uses the of_serial device driver to determine necessary properties from
the device tree.  The supported device is added as serial port number 85.

NWP stands for network processor and it is part of the QPACE - Quantum
Chromodynamics Parallel Computing on the Cell Broadband Engine project.
The implementation is a lightweight uart implementation with the focus
to consume as little resources as possible and it is connected to a
DCR bus.
Signed-off-by: NBenjamin Krill <ben@codiert.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Update the serial driver to handle the 4 ports of the
S3C2443 and S364XX series.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support to the Samsung serial driver for the S3C6400
and S3C6410 serial ports.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add serial support for S3C24A0, based on current S3C2410
UART driver. It adds necessary new defines in regs-serial.h
for S3C24A0 and the code to support this device in
drivers/serial/s3c24a0.c
Signed-off-by: NSandeep Patil <sandeep.patil@azingo.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Make the netX serial driver tristate (as the help text implied). Make the
serial driver build correctly if the netX serial console is disabled. Do not
allow the netX serial console if the netX serial driver is build as a module.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The SERIAL_SAMSUNG_DEBUG used printascii() to avoid debugging
through itself when selected as a console. Disable this option
when DEBUG_LL is not set (printascii is unavailable).
Signed-off-by: NBen Dooks <ben-linux@fluff.org>