When doing key selection for software decryption, mac80211 gets
a few things wrong: it always uses pairwise keys if configured,
even if the frame is addressed to a multicast address. Also, it
doesn't allow using a key index of zero if a pairwise key has
also been found.

This patch changes the key selection code to be (more) in line
with the 802.11 specification. I have confirmed that with this,
multicast frames are correctly decrypted and I've tested with
WEP as well.

While at it, I've cleaned up the semantics of the hardware flags
IEEE80211_HW_WEP_INCLUDE_IV and IEEE80211_HW_DEVICE_HIDES_WEP
and clarified them in the mac80211.h header; it is also now
allowed to set the IEEE80211_HW_DEVICE_HIDES_WEP option even if
it only applies to frames that have been decrypted by the hw,
unencrypted frames must be dropped but encrypted frames that
the hardware couldn't handle can be passed up unmodified.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Neither hostapd nor wpa_supplicant really use it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Many if not all of these messages can be triggered by sending
a few rogue frames which is trivially done and then we overflow
our logs.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David Woodhouse noticed that under some circumstances the number of slab
allocations kept growing. After looking a bit, this seemed to happen
when you had a management mode interface that was *down*.

The reason for this is that when the device is down, all management
frames get queued to the in-kernel MLME (via ieee80211_sta_rx_mgmt) but
then the sta work is invoked but doesn't run when the netif is down.
When you then bring the interface up, all such frames are freed, but if
you change the mode all of them are lost because the skb queue is
reinitialised as soon as you go back to managed mode. The skb queue is
correctly cleared when the interface is brought down, but the code
doesn't account for the fact that it may be filled while it is not up.

This patch should fix the issue by simply ignoring all interfaces that
are down when going through the RX handlers.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some more outdenting to make the code more readable.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

pre_rx handlers can't really touch sta since for IBSS it might not be
assigned yet, it can create sta info structs on-the-fly.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The really indented part that does the huge switch on the interface
type is a nuisance. Put it into an own function 'prepare_for_handlers'.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ieee80211_rx_h_check handler really does two things, it's
a lot easier to understand if it's split into ieee80211_rx_h_check
and ieee80211_rx_h_load_key, and it may be possible in the future
to optimise the key loading to not do it for each interface.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make some really indented code more readable by outdenting.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves the QoS handlers into rx.c making it possible
to compile wme.c only when NET_SCHED is defined.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>