replace au_read/write/sync with __raw_read/write and wmb.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7465/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch changes the static memory controller registers to offsets
from base, prefixes them with AU1000_ to avoid silent failures due to
changed addresses and introduces helpers to access them.

No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7463/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch changes all absolute SYS_XY registers to offsets from the
SYS block base, prefixes them with AU1000 to avoid silent failures due
to changed addresses, and introduces helper functions to read/write
them.

No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7464/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move the C-code after all macros:  A follow-on patch which
introduces helpers to access the SYS_* registers needs this to build.

Just code shuffling, no functional changes.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7461/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move the register offsets and bit descriptions from the au1000.h header
to their only user, the au1000_eth.c driver.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: netdev@vger.kernel.org
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7460/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove the unused SSI I2S and AC97C register definitions.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7462/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The UART register names are identical to the ones in uapi/linux/serial_reg.h,
which causes build failures in various drivers when they indirectly pull in
the au1000.h header, for example via gpio.h:

In file included from arch/mips/include/asm/mach-au1x00/gpio.h:13:0,
                 from arch/mips/include/asm/gpio.h:4,
                 from include/linux/gpio.h:48,
                 from include/linux/ssb/ssb.h:9,
                 from drivers/ssb/driver_mipscore.c:11:
arch/mips/include/asm/mach-au1x00/au1000.h:1171:0: note: this is the location of the previous definition
 #define UART_LSR 0x1C /* Line Status Register */

Get rid of the altogether, nothing in the core Alchemy code depends
on them any more.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6664/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Replace hardcoded CP0 PRId and CP1 FPIR register access masks throughout.
The change does not touch places that use shifted or partial masks.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5838/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Moderate driver cleanup:
convert to platform driver, get rid of board-specific code.

Driver loads and runs on a DB1100 board.  But since I have no other
IrDA hardware to exchange data with I can't say whether it really sends
and receives.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: netdev@vger.kernel.org
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2877/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add basic support for the Au1300 variant(s):
- New GPIO/Interrupt controller
- DBDMA ids
- USB setup
- MMC support
- enable various PSC drivers
- detection code.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2866/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Now that no driver any longer depends on the CONFIG_SOC_AU1???  symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files.  Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

- Rewrite Alchemy PCI support as a platform driver.
- Fixup boards which have PCI.

Run-tested on DB1500 and DB1550.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2706/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 delete mode 100644 arch/mips/alchemy/common/pci.c
 delete mode 100644 arch/mips/pci/fixup-au1000.c
 delete mode 100644 arch/mips/pci/ops-au1000.c
 create mode 100644 arch/mips/pci/pci-alchemy.c

remove all redundant peripheral base address defines, fix
all affected boards and drivers.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2700/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use runtime CPU detection to setup all USB parts.
Remove the Au1200 OTG and UDC platform devices since there are no
drivers for them anyway.
Clean up the USB address mess in the au1000 header.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2703/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Alchemy chips have one or more registers which control access
to the usb blocks as well as PHY configuration.  I don't want
the OHCI/EHCI glues to know about the different registers and bits;
new code hides the gory details of USB configuration from them.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-usb@vger.kernel.org
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Patchwork: https://patchwork.linux-mips.org/patch/2709/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 create mode 100644 drivers/usb/host/alchemy-common.c

remove au_readl/au_writel, remove the predefined GPIO1/2 KSEG1 register
addresses and fix the fallout in all boards and drivers.

This also fixes a bug in the mtx-1_wdt driver which was introduced by
commit 6ea8115b
("Convert mtx1 wdt to be a platform device and use generic GPIO API")
before this patch mtx-1_wdt only modified GPIO215, the patch then
used the gpio resource information as bit index into the GPIO2 register
but the conversion to the GPIO API didn't realize that.
With this patch the drivers original behaviour is restored and GPIO15
is left alone.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
Cc: Florian Fainelli <florian@openwrt.org>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-watchdog@vger.kernel.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Patchwork: https://patchwork.linux-mips.org/patch/2381/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org

According to the databooks, the Au1000 DMA engine must be programmed with
the physical FIFO addresses.  This patch does that; furthermore this
opened the possibility to get rid of a lot of now unnecessary address
defines.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2348/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org

Rewrite ethernet setup to use runtime cpu detection, and also clean up
the ethernet base address mess as far as possible.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2353/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org

Detect CPU type at runtime and setup uarts accordingly; also clean up the
uart base address mess in the process as far as possible.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2352/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org

Convert the PM sysdev to syscore_ops and clean up the ddma addresses a bit.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2351/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

replace au_readl/au_writel with __raw_readl/__raw_writel,
and clean up IC-related stuff from the headers.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2354/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Split the low-level sleepcode into per-cpu functions instead of
relying on compile-time-defined cpu type.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1281/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use a sysdev to implement PM methods for the Au1000 interrupt controllers.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1114/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

On Alchemy the PCMCIA area lies at the end of the chips 36bit system bus
area.  Currently, addresses at the far end of the 32bit area are assumed
to belong to the PCMCIA area and fixed up to the real 36bit address before
being passed to ioremap().

A previous commit enabled 64 bit physical size for the resource datatype on
Alchemy and this allows to use the correct 36bit addresses when registering
the PCMCIA sockets.

This patch removes the 32-to-36bit address fixup and registers the Alchemy
demo board pcmcia socket with the correct 36bit physical addresses.

Tested on DB1200, with a CF card (ide-cs driver) and a 3c589 PCMCIA ethernet
card.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/994/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

I believe these changes are needed on Alchemy SoCs in order to
use iomem above 4G with the usual platform_device machinery:

- Set CONFIG_ARCH_PHYS_ADDR_T_64BIT to make resource_size_t 64-bit.
- Increase IOMEM_RESOURCE_END so that platforms can register resources.

To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/814/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Nothing in-tree uses it, so get rid of it.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove unused uart bit definitions and base macros.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch replaces the general alchemy prom_putchar() implementation
in favor of board-specific versions:  The UART where the output of
prom_putchar is directed to really depends on the board, the current
implementation hardcodes this on a per-SoC basis which is just wrong.

So a generic uart tx function is provided in the alchemy headers,
and the boards can provide their own prom_putchar with custom
destination uart, and all in-kernel alchemy boards support
early printk.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Eliminate the sharing of IRQ names among the differenct Alchemy
variants.  IRQ numbers need no longer be hidden behind a
CONFIG_SOC_AU1XXX symbol: step 1 in my quest to make the Alchemy
code less reliant on a hardcoded subtype.

This patch also renames the GPIO irq number constants. It's really
an interrupt line, NOT a GPIO number!

Code which relied on certain irq numbers to have the same name
across all supported cpu subtypes is changed to determine current
cpu subtype at runtime; in some places this isn't possible so
a "compat" symbol is used.

Run-tested on DB1200.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Extract the alchemy chip variant from c0_prid register.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/14/
Patchwork: http://patchwork.linux-mips.org/patch/707/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

New PCMCIA socket driver for all Db/Pb1xxx boards (except Pb1000),
which replaces au1000_db1x00.c and (most of) au1000_pb1x00.c.
Notable improvements:
        - supports Db1000, DB/PB1100/1500/1550/1200.
        - support for carddetect and statuschange IRQs.
        - pcmcia socket mem/io/attr areas and irqs passed through
          platform resource information.
        - doesn't freeze system during card insertion/ejection like
          the one it replaces.
        - boardtype is automatically detected using BCSR ID register.

Run-tested on the DB1200.

Cc: Linux-PCMCIA <linux-pcmcia@lists.infradead.org>
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

remove board_init_irq():  On all in-kernel boards it is sufficient to
initialize board interrupts in an arch_initcall by using the default
linux irq functions.

Some small irqmap.c files have been folded into board_setup files.

Run-tested on DB1200; compile-tested on all other affected boards.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Replace the current sysctl-based suspend interface with a new sysfs-
based one which also uses the Linux-2.6 suspend model.

To configure wakeup sources, a subtree for the demoboards is created
under /sys/power/db1x:

sys/
`-- power
    `-- db1x
        |-- gpio0
        |-- gpio1
        |-- gpio2
        |-- gpio3
        |-- gpio4
        |-- gpio5
        |-- gpio6
        |-- gpio7
        |-- timer
        |-- timer_timeout
        |-- wakemsk
        `-- wakesrc

The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2
bits of the SYS_WAKEMSK (wakeup source enable) register.  Writing '1'
enables a wakesource, 0 disables it.

The 'timer_timeout' node holds the timeout in seconds after which the
TOYMATCH2 event should wake the system.

The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex),
the 'wakemsk' node can be used to get/set the wakeup mask directly.

For example, to have the timer wake the system after 10 seconds of sleep,
the following must be done in userspace:

echo 10 > /sys/power/db1x/timer_timeout
echo 1 > /sys/power/db1x/timer
echo mem > /sys/power/sleep

This patch also removes the homebrew CPU frequency switching code.  I don't
understand how it could have ever worked reliably; it does not communicate
the clock changes to peripheral devices other than uarts.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 create mode 100644 arch/mips/alchemy/devboards/pm.c

Au1550/Au1200 have a different memory controller which requires additi-
onal code to properly put memory to sleep (code taken from AMD/RMI's
Linux-2.6.11 source package).

Also fix up the remaining pm-related paths to compile on Au1200/Au1550
platforms.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Now that nothing in time.c depends on calc_clock, it can
be moved to clocks.c where it belongs.
While at it, give it a better non-generic name and call it
as soon as possible in plat_mem_init.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove the cpu_table:
- move detection of whether c0_config[OD] is read-only and should be set
  to fix various chip errata to au1000 headers.
- move detection of write-only sys_cpupll to au1000 headers.
- remove the BCLK switching code:  Activation of this features should be
  left to the boards using the chips since it also affects external devices
  tied to BCLK, and only the board designers know whether it is safe to
  enable.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 delete mode 100644 arch/mips/alchemy/common/cputable.c

There are no in-tree users, so remove them.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>