Now that qla2xxx uses the IRQ layer affinity assignment, affinity won't
change over the life time of a device and the notifiers are useless.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The first two or three vectors in qla2xxx adapter are global and not
associated with a specific queue.  They should not have IRQ affinity
assigned.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

- Fix race condition between dpc_thread accessing Multiqueue resources
  and qla2x00_remove_one thread trying to free resource.
- Fix out of order free for Multiqueue resources. Also, Multiqueue
  interrupts needs a workqueue. Interrupt needed to stop before
  the wq can be destroyed.
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Replaced existing multiple queue functionality with framework
that allows for the creation of pairs of request and response queues,
either at start of day or dynamically.

Queue pair creation depend on module parameter "ql2xmqsupport",
which need to be enabled to create queue pair.
Signed-off-by: NSawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: NMichael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Replaces the old pci_enable_msi[x]* and pci_disable_msi[x] calls.
Signed-off-by: NMichael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Change FC drivers to use 'struct bsg_job' from bsg-lib.h instead of
'struct fc_bsg_job' from scsi_transport_fc.h and remove 'struct
fc_bsg_job'.
Signed-off-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Acked-by: NTyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Instead of defining a local version of it.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

During hot swap of PCI device, there can be PCI error on device,
during normal driver unload. The race between normal driver unload and
driver unload due to PCI error, can lead to system crash.Fix is to check
if there is unload going on and allow that function to unload the driver.
Signed-off-by: NSawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Properly initialize IO statistics to avoid initial 0xFFFFFFF (-1) values.

Cleanup/simplify usage of pointer to statistics structure.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

 #cat  /sys/kernel/debug/qla2xxx/qla2xxx_31/tgt_sess
 qla2xxx_31
 Port ID   Port Name                Handle
 ff:fc:01  21:fd:00:05:33:c7:ec:16  0
 01:0e:00  21:00:00:24:ff:7b:8a:e4  1
 01:0f:00  21:00:00:24:ff:7b:8a:e5  2
 ....

(Drop ->check_initiator_node_acl() parameter usage - nab)
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NHarish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

set ATIO/Request/Response Queues and Default number
of outstanding command to 4k.
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

99% of the time the ATIOQ has SCSI command.  The other 1% of time
is something else.  Most of the time this interrupt does not need
to hold the hardware_lock.  We're moving the ATIO interrupt thread
to a different lock to reduce lock contention.
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Register to receive notification of when irq setting change
occured.
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Sessions management (add, deleted, modify) currently are serialized
through the hardware_lock.  Hardware_lock is a high traffic lock.
This lock is accessed by both the transmit & receive sides.

Sessions management is now moved off to another lock call sess_lock.
This is done to reduce lock contention and increase traffic throughput.
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Until now ack'ing of a new PLOGI has only been delayed if there
was an existing session for the same WWN. Ack was released when
the session deletion completed.

If there was another WWN session with the same fc_id/loop_id pair
(aka "conflicting session"), PLOGI was still ack'ed immediately.
This potentially caused a problem when old session deletion logged
fc_id/loop_id out of FW after new session has been established.

Two work-arounds were attempted before:
1. Dropping PLOGIs until conflicting session goes away.
2. Detecting initiator being logged out of FW and issuing LOGO
to force re-login.

This patch introduces proper solution to the problem where PLOGI
is held until either existing session with same WWN or any
conflicting session goes away. Mechanism supports one session holding
two PLOGI acks as well as one PLOGI ack being held by many sessions.
Signed-off-by: NAlexei Potashnik <alexei@purestorage.com>
Acked-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

1. Initiator A is logged in with fc_id(1)/loop_id(1)
2. Initiator A re-logs in with fc_id(2)/loop_id(2)
3. Part of old session deletion async logoout for 1/1 is queued
4. Initiator B logs in with fc_id(1)/loop_id(1), starts
   passing data and creates session.
5. Async logo from 3 is processed by DPC and sent to FW

Now initiator B has the session but is logged out from FW.

This condition is detected first with CTIO error 29 at which
point we should delete current session. During session
deletion we will send LOGO to initiator to force re-login.

Under rare circumstances initiator might be logged out of FW,
not have driver session, but still think it's logged in.
E.g. the above sequence plus session deletion due to re-config.
Incoming commands will fail to create local session because
initiator is not found in FW. In this case we also issue LOGO
to initiator to force him re-login.

Finally this patch fixes exchange leak when commands where
received in logged out state. In this case loop_id must be
set to FFFF when corresponding exchange is terminated. The
patch modifies exchange termination to always use FFFF,
since in certain scenarios it's impossible to tell whether
command was received in logged in or logged out state.
Signed-off-by: NAlexei Potashnik <alexei@purestorage.com>
Acked-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds interface to send explicit LOGO
explicit LOGO using using ELS commands from driver.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

DebugFS now will show fw_resource_count node.

FW Resource count

Original TGT exchg count[0]
current TGT exchg count[0]
original Initiator Exchange count[2048]
Current Initiator Exchange count[2048]
Original IOCB count[2078]
Current IOCB count[2067]
MAX VP count[254]
MAX FCF count[0]
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Following counters are added in target mode to help debugging efforts.

Target Counters

qla_core_sbt_cmd = 0
qla_core_ret_sta_ctio = 0
qla_core_ret_ctio = 0
core_qla_que_buf = 0
core_qla_snd_status = 0
core_qla_free_cmd = 0
num alloc iocb failed = 0
num term exchange sent = 0
num Q full sent = 0
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch enables Exchange offload support in Qlogic ISP.
To enable exchange offload with Qlogic ISP24XX/25XX/26XX,
set module parameter ql2xexchoffld to any non-zero number.
This will alow ISP firmware to store exchange data structures
used by firmware to host memory provided by driver. ISP firmware
can supports upto 32k total active exchanges.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch enables Extended Logins support in Qlogic ISP.
To enable extended login with Qlogic ISP24XX/25XX/26XX,
set module parameter ql2xexlogins to any non-zero number.
This will alow ISP firmware to store port database structure
information of remote login sessions to host memory provided
by driver. ISP firmware supports upto 16k total logins.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NSawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

This patch removes 21 casts between an __iomem pointer type and
another data type but also introduces five new casts (see also
the casts with "__force"). Although this patch does not change
any functionality, IMHO the code with __force casts needs further
review.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Acked-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

RSCN processing in qla2xxx driver can run in parallel with ELS/IO
processing. As such the decision to remove disappeared fc port's
session could be stale, because a new login sequence has occurred
since and created a brand new session.

Previous mechanism of dealing with this by delaying deletion request
was prone to erroneous deletions if the event that was supposed to
cancel the deletion never arrived or has been delayed in processing.

New mechanism relies on a time-like generation counter to serialize
RSCN updates relative to ELS/IO updates.

Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: NAlexei Potashnik <alexei@purestorage.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

- keep qla_tgt_sess object on the session list until it's freed

- modify use of sess->deleted flag to differentiate delayed
  session deletion that can be cancelled from irreversible one:
  QLA_SESS_DELETION_PENDING vs QLA_SESS_DELETION_IN_PROGRESS

- during IN_PROGRESS deletion all newly arrived commands and TMRs will
  be rejected, existing commands and TMRs will be terminated when
  given by the core to the fabric or simply dropped if session logout
  has already happened (logout terminates all existing exchanges)

- new PLOGI will initiate deletion of the following sessions
  (unless deletion is already IN_PROGRESS):
  - with the same port_name (with logout)
  - different port_name, different loop_id but the same port_id
    (with logout)
  - different port_name, different port_id, but the same loop_id
    (without logout)

- additionally each new PLOGI will store imm notify iocb in the
  same port_name session being deleted. When deletion process
  completes this iocb will be acked. Only the most recent PLOGI
  iocb is stored. The older ones will be terminated when replaced.

- new PRLI will initiate deletion of the following sessions
  (unless deletion is already IN_PROGRESS):
  - different port_name, different port_id, but the same loop_id
   (without logout)

Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: NAlexei Potashnik <alexei@purestorage.com>
Acked-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Since cmds go into qla_tgt_wq and TMRs don't, it's possible that TMR
like TASK_ABORT can be queued over the cmd for which it was meant.
To avoid this race, use a per-port list to keep track of cmds that
are enqueued to qla_tgt_wq but not yet processed. When a TMR arrives,
iterate through this list and remove any cmds that match the TMR.
This patch supports TASK_ABORT and LUN_RESET.

Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: NSwapnil Nagle <swapnil.nagle@purestorage.com>
Signed-off-by: NAlexei Potashnik <alexei@purestorage.com>
Acked-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: NNicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

On some vendor switches, when switch port is toggled (down /up),
then in some condition driver tries to configure virtual port,
before FW is actually in ready state to process any commands on wire.
At this time, configuring virtual port can fail. Add fix in driver
to make driver wait, for FW to be ready state before
Signed-off-by: NSawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>