dump_firm_type_and_int_freq() can become static.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There's no need to load SCode table for FM.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Try to load non-MTS firmware instead.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If we are selecting the S-Code firmware to load by name, then we must mask
off the HAS_IF bit during the search.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

xc2028_attach was returning an integer when disabled from the build, where it
should instead be returning NULL.  Declare xc2028_attach as type dvb_frontend *
instead of void *.

The prototype declaration must be marked as extern in the header.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

In my testing yesterday, I was using a scan file tailored specifically
for a unique test situation -- As it turns out, this scan file was bad,
and I will use the one included inside dvb-apps for testing for now on.

I've tested with other ATSC tuners just to confirm, using:

us-ATSC-center-frequencies-8VSB

Anyhow, as it turns out, the tuner-xc2028 *does* require a tuning offset
for ATSC.  Even though the linux-dvb api passes in center frequencies
from userspace, apparantly the xceive firmware is already factoring in
the tuning offset to center.

In order to make the device function using the same scan files /
channels.conf configurations as other atsc devices, we must offset by
1.75 MHz.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

ATSC works with offset=0
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

It seems that the DTV78 firmware is intended for use in locations where
VHF channels have 7MHz bandwidth and UHF channels have 8MHz bandwidth.
If we switch to DTV78 firmware when we detect this condition, we can
avoid firmware reloads when switching between VHF and UHF transponders.

Place the state for this in the control structure so that card drivers
can hint to us to use DTV78 firmware from the first tuning attempt.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

We have been inserting a mystery 500kHz offset for tuning 7MHz channels,
however some experimentation reveals it is only needed under certain
conditions with specific firmware combinations.  Document these and only
apply the offset when we know it is required.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When searching for the right S-Code table to load, check the HAS_IF flag
against the firmware we are checking instead of against the the "type"
requested.  We already ignore the scode type requested if the caller passed
an int_freq; this makes the search by frequency consistent with that behaviour.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Don't modify the control structure that was provided at attach when applying
an offset to the S-Code, otherwise it will be incorrect on subsequent tunes.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add "int_freq" to the debugging output when selecting firmware and the
HAS_IF flag when dumping firmware during load.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

ATSC standard-specific firmware is D2633 on both v2.5 and v2.7. Better to
auto-select this firmware, overriding ctrl.d2633.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

DVB-S is not supported. Also, there are some QAM6 firmwares for xc3028, but it
is reported that this doesn't work fine.

Thanks to Manu Abraham, Michael Krufky and Patrick Boettcher for their
insights.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

A previous patch implemented support for non-OFDM digital TV. However, the
previous bandwidth ofdm parameter were left at the code by mistake.

Thanks to Michael Krufky and Patrick Boettcher for noticing this mistake.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

s-code tables are related to IF frequency used for video demodulation.

The s-codes for analog are automatically loaded, according with video standard.
However, for digital, they will depend on the IF of the demoduler chip. IF of
the demoduler.

Before this patch, only a few IF's where possible to use. This patch allows
selecting any IF defined at firmware file.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Since check_firmware is called via analog or digital set freq routines, move
type selection to those routines. This avoids having several if's at the code,
and simplifies the source code.

A sideback effect is that implementing radio and other dvb types will become
simpler.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Not all 8MHz firmware are marked with F8MHz.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

On some cases, xc2028/xc3028 wents into "turn off" mode. It seems that this
happens when very weak signals are tuned. To solve this, specific standard
reaload were done previously. Christopher patches changed this behavior to a
complete firmware reload.

This patch removes the hack. A much cleaner solution for this trouble is just
to sent a xc2028/3028 software reset.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

xc3028 can be used on some DTV only designs (for example, DVB-S boards). Before
this patch, a DTV only board would need to call set_tuner_config callback.

This patch allows to optionally pass a xc3028_ctrl parameter, via xc3028_config
struct, fully initializing the driver for DTV.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Xc2028.3028 has two type of firmwares: audio-standard specific ones and
baseband MTS firmwares. MTS firmwares provide stereo decoding for 6 MHz
BTSC/EIAJ and for monoaural audio decoding on 8 MHz firmwares.

It seems that the option to use MTS or a standard-specific audio decoding
depends on the way xc2028/3028 is connected.

Instead of wasting 32 (or 64 bits) to signalize if the driver needs to use MTS
firmware, this patch converts it to a bitfield that can be shared with other
proprieties of xc2028/3028.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Some drivers call set_frequency before selecting the video standard. Before
this patch, an invalid standard ID could be assumed.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Those standards use 6 MHz firmware.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When loading init1 firmware, there may not be an 8MHz specific version.
Load the non-8MHz version if it exists.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When searching for standard-specific analog firmware, only certain
type bits are valid, much like for DTV.  Mask them off when finding
the firmware to load.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When loading BASE firmware, we must use std = 0.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add sleep method to enable putting the tuner into standby mode.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

In practice, the tuner occasionally fails to respond correctly after a
firmware load.  Retry the firmware load if the firmware/hardware version
we read back from the tuner after programming does not match what we
expect.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Define a list of valid "firmware types" for each combination of BASE,
DTV and SCODEs.  By masking the appropriate firmware bits off we can
just use one "type" for the firmware searching and also flag when we
are looking for a BASE, DTV or SCODE type firmware.  This makes it
much easier to track if we need to change device modes or flash an
individual firmware part.

Add a structure to remember what firmware properties we have.  This
contains the currently loaded/wanted  base firmware (type), video std
(id), video std requested (std_req), scode file and number in use.

Incorporate said structure into the tuner private data.

When checking whether the current firmware needs to be reloaded, first
figure out exactly what "type" of firmware we want (base, std and
scode), and then proceed to load the appropriate matching base,
std-specific and scode records iff there are any changes required.
This removes guesswork from the process because we no longer need to
individually code a check for every tuning parameter's interactions.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add a bit to select D2633 DTV firmware to struct xc2028_ctrl, so that it can
be enabled via .set_config.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When validating and loading SCODE firmware we need to take into account the
two-byte size header before each entry.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Rather than picking the first video standard firmware that supports any of
the standards that the user has requested, try to select one that supports
as many of them as possible.  This improves the likelihood that the firmware
we select will support the user's desired TV standard.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There is no need to duplicate the max_len field from the ctrl structure
in the private data.  If we use it directly from priv->ctrl, we can memcpy
the structure (apart from strings) to reduce maintenance as it grows.

Enforce a minimum max_len length of 8 data bytes (+ 1 address byte) as seems
to be required by the tuner.

Also, use kstrdup instead of open coding the string duplication.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

7MHz bandwidth DVB-T needs an adjusted offset at the PLL to ensure the IF
output is correctly centered.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

We were using priv->bandwidth to select the base firmware to load, not the
requested bandwidth value, oops.  Also, 7MHz Digital TV needs 8MHz base
firmware loaded.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The frequency divisor should only be four bytes long.  Also, display the
frequency and divisor correctly in the debug output.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Hold the private lock over set_config and set priv->firm_size to 0 after a
failed firmware load to prevent firmware accidentally being freed on us.

Clean up the firmware load/error messages somewhat and rename priv->version
to priv->firm_version to make it clear which "version" it is.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>