Data sheet at:
http://www.sensirion.ch/en/pdf/product_information/Datasheet-humidity-sensor-SHT1x.pdf

These sensors communicate over a 2 wire bus running a device specific
protocol.  The complexity of the driver is mainly due to handling the
substantial delays between requesting a reading and the device pulling the
data line low to indicate that the data is available.  This is handled by
an interrupt that is disabled under all other conditions.

I wasn't terribly clear on the best way to handle this, so comments on
that aspect would be particularly welcome!

Interpretation of the temperature depends on knowing the supply voltage.
If configured in a board config as a regulator consumer this is obtained
from the regulator subsystem.  If not it should be provided in the
platform data.

I've placed this driver in the hwmon subsystem as it is definitely a
device that may be used for hardware monitoring and with it's relatively
slow response times (up to 120 millisecs to get a reading) a caching
strategy certainly seems to make sense!
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

efifb will attempt to ioremap a framebuffer even if its starting address
is 0, failing and causing an ugly backtrace in the process.  Exit before
probing if this is the case.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Acked-by: NPeter Jones <pjones@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

uvesafb incorrectly sets the length of the color fields to 6 bits for
PSEUDOCOLOR modes, even though 8 bits are always used per pixel.  Fix this
by setting the length to 8.

The switch of the DAC width from the default 6 bits to 8 bits is retained
and tracked internally in the driver, but never exposed to userspace.
Signed-off-by: NMichal Januszewski <spock@gentoo.org>
Acked-by: NKrzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <syrjala@sci.fi>
Cc: Geert Uytterhoeven <geert.uytterhoeven@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The documentation about the meaning of the color component bitfield
lengths in pseudocolor modes is inconsistent.  Fix it, so that it
indicates the correct interpretation everywhere, i.e.  that 1 << length is
the number of palette entries.
Signed-off-by: NMichal Januszewski <spock@gentoo.org>
Acked-by: NKrzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <syrjala@sci.fi>
Acked-by: NGeert Uytterhoeven <geert.uytterhoeven@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

fb_notifier_call_chain() is called with info->lock held, i.e.  in
do_fb_ioctl() => FBIOPUT_VSCREENINFO => fb_set_var() and the some
notifier callbacks, like fbcon_event_notify(), try to re-acquire
info->lock again.

Remove the lock/unlock_fb_info() in all the framebuffer notifier
callbacks' and be sure to always call fb_notifier_call_chain() with
info->lock held.
Reported-by: NPavel Roskin <proski@gnu.org>
Reported-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NAndrea Righi <righi.andrea@gmail.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove unused #include <version.h> in drivers/hwmon/hp_accel.c.
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There is a race between resume from hibernation and the asynchronous
scanning of SCSI devices and to prevent it from happening we need to
call scsi_complete_async_scans() during resume from hibernation.

In addition, if the resume from hibernation is userland-driven, it's
better to wait for all device probes in the kernel to complete before
attempting to open the resume device.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

While it isn't the way the standard device binding model works, it is
OK for new-style drivers to implement attach_adapter. It may help
convert the renaming legacy drivers to new style drivers faster.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>

Support for I2C/DDC was recently added to the tdfxfb driver, which
means that the i2c-voodoo3 driver can be deprecated.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>

A recent change broke debugging of pca_xfer(), fix it.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>

Also remove the now-useless debug printouts which are supposed to
tell us when the scan starts and ends.
Signed-off-by: NVegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Along with MCP65, MCP67 and 73 also don't set CAP_NCQ.  Force it.
Reported by zaceni@yandex.ru on bko#13014 and confirmed by Peer Chen.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NNightFox <zaceni2@yandex.ru>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Reported and initial patch by Marin Mitov.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This reverts commit 5d38258e, since the
underlying problem got fixed properly in the previous commit ("async:
Fix module loading async-work regression").

Cc: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If the BIOS does something obviously stupid, like claiming that the
registers for the IOMMU are at physical address zero, then print a nasty
message and abort, rather than trying to set up the IOMMU and then later
panicking.

It's becoming more and more obvious that trusting this stuff to the BIOS
was a mistake.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

MN10300 arch headers and place them instead in the same directories as contain
the .c files for the processor and unit implementations.

This permits the symlinks include/asm/proc and include/asm/unit to be
dispensed with.  This does, however, require that #include <asm/proc/xxx.h> be
converted to #include <proc/xxx.h> and similarly for asm/unit -> unit.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

If the thread calling dm_kcopyd_copy is delayed due to scheduling inside
split_job/segment_complete and the subjobs complete before the loop in
split_job completes, the kcopyd callback could be invoked from the
thread that called dm_kcopyd_copy instead of the kcopyd workqueue.

dm_kcopyd_copy -> split_job -> segment_complete -> job->fn()

Snapshots depend on the fact that callbacks are called from the singlethreaded
kcopyd workqueue and expect that there is no racing between individual
callbacks. The racing between callbacks can lead to corruption of exception
store and it can also mean that exception store callbacks are called twice
for the same exception - a likely reason for crashes reported inside
pending_complete() / remove_exception().

This patch fixes two problems:

1. job->fn being called from the thread that submitted the job (see above).

- Fix: hand over the completion callback to the kcopyd thread.

2. job->fn(read_err, write_err, job->context); in segment_complete
reports the error of the last subjob, not the union of all errors.

- Fix: pass job->write_err to the callback to report all error bits
  (it is done already in run_complete_job)

Cc: stable@kernel.org
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Use a variable in segment_complete() to point to the dm_kcopyd_client
struct and only release job->pages in run_complete_job() if any are
defined.  These changes are needed by the next patch.

Cc: stable@kernel.org
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Barriers are submitted to a worker thread that issues them in-order.

The thread is modified so that when it sees a barrier request it waits
for all pending IO before the request then submits the barrier and
waits for it.  (We must wait, otherwise it could be intermixed with
following requests.)

Errors from the barrier request are recorded in a per-device barrier_error
variable. There may be only one barrier request in progress at once.

For now, the barrier request is converted to a non-barrier request when
sending it to the underlying device.

This patch guarantees correct barrier behavior if the underlying device
doesn't perform write-back caching. The same requirement existed before
barriers were supported in dm.

Bottom layer barrier support (sending barriers by target drivers) and
handling devices with write-back caches will be done in further patches.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Remove queue_io return value and a loop in dm_request.

IO may be submitted to a worker thread with queue_io().  queue_io() sets
DMF_QUEUE_IO_TO_THREAD so that all further IO is queued for the thread. When
the thread finishes its work, it clears DMF_QUEUE_IO_TO_THREAD and from this
point on, requests are submitted from dm_request again. This will be used
for processing barriers.

Remove the loop in dm_request. queue_io() can submit I/Os to the worker thread
even if DMF_QUEUE_IO_TO_THREAD was not set.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Rework shutting down on suspend and document the associated rules.

Drop write lock in __split_and_process_bio to allow more processing
concurrency.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Refactor the code in dm_request().

Require the new DMF_BLOCK_FOR_SUSPEND flag on readahead bios we will
discard so we don't drop such bios while processing a barrier.
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Split the DMF_BLOCK_IO flag into two.

DMF_BLOCK_IO_FOR_SUSPEND is set when I/O must be blocked while suspending a
device.  DMF_QUEUE_IO_TO_THREAD is set when I/O must be queued to a
worker thread for later processing.
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Refactor dm_wq_work() to make later patch more readable.
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Prepare for full barrier implementation: first remove the restricted support.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

This patch provides support for data integrity passthrough in the device
mapper.

 - If one or more component devices support integrity an integrity
   profile is preallocated for the DM device.

 - If all component devices have compatible profiles the DM device is
   flagged as capable.

 - Handle integrity metadata when splitting and cloning bios.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

This patch removes the sysfs entry num_vfs which was added to support
enabling pci virtual functions for 82576.

To prevent VFs from loading automatically a module parameter "max_vfs" was
added so that the number of VFs per PF can be limited.  This is especially
useful when 4 or more 82576 ports are on the system because otherwise to
load all VFs would result in 8 interface per physical port.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds an igbvf driver to handle virtual functions provided by the
igb driver when SR-IOV has been enabled.  A virtual function is a
lightweight pci-e function that supports a single queue and shares
resources with the 82576 physical function contained within the igb
driver.

To spawn virtual functions from the igb driver all that is needed is to
enable CONFIG_PCI_IOV and have an 82576 Ethernet adapter on a system that
supports SR-IOV in the BIOS.  The virtual functions will appear after the
interface is loaded.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After dev_get_by_name(), we should follow a dev_put().
Signed-off-by: NYang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't strain gcc's tiny mind.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch sets MODULE_VERSION in order to help users track
changes to this module.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mips identifier is reserved by gcc on mips plattforms. Don't use it
in the code.
Signed-off-by: NBastian Blank <waldi@debian.org>
Tested-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

platform_device_register_simple() returns ERR_PTR(), not NULL, if an error 
occurs.

Found by smatch (http://repo.or.cz/w/smatch.git).  Compile tested.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move SDMA configuration from interface up to port probe, to prevent
overwriting the receive coalescing timer value on interface up.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the warning printed when a mii READ times out currently says "Timed out
waiting for MII write to finish".  This patch corrects this.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ethoc indirectly uses crc32_le() and bitrev32(), so select
those library functions to be built.

drivers/built-in.o: In function `ethoc_set_multicast_list':
ethoc.c:(.text+0x6226f): undefined reference to `crc32_le'
ethoc.c:(.text+0x62276): undefined reference to `bitrev32'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Thou shalt remember to use 'git add' or errors shall be visited on your
downloads and there shall be wrath from on list and much gnashing of teeth.

Thou shalt remember to use git status or there shall be catcalls and much
embarrasment shall come to pass.
Signed-off-by: NAlan "I'm hiding" Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add new register settings for new SFP+ PHY/firmware.
Add new PHY to to nes_netdev_get/set_settings.
Signed-off-by: NChien Tung <chien.tin.tung@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

We have observed unstable link with a new BNT switch.

Add wide_ppm_offset parameter to allow the user to control the clock
ppm offset on the CX4 interface for better compatibility.  Default is
100ppm, setting it to 1 will increase it to 300ppm.  Change default
SerDes1 reference clock to external source.
Signed-off-by: NChien Tung <chien.tin.tung@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>