Skip to content

K
kernel_linux

OpenHarmony / kernel_linux
上一次同步 3 年多

通知 13
Star 8
Fork 2
K
kernel_linux
切换分支/标签
  1. 10 2月, 2007 13 次提交
  3. 03 2月, 2007 1 次提交
  5. 30 1月, 2007 1 次提交
  7. 25 1月, 2007 1 次提交
  9. 16 12月, 2006 1 次提交
  11. 07 12月, 2006 2 次提交
  13. 03 12月, 2006 7 次提交
    • T
      [PATCH] libata: always use polling IDENTIFY · 800b3996
      由 Tejun Heo 提交于 
      libata switched to IRQ-driven IDENTIFY when IRQ-driven PIO was
introduced.  This has caused a lot of problems including device
misdetection and phantom device.

ATA_FLAG_DETECT_POLLING was added recently to selectively use polling
IDENTIFY on problemetic drivers but many controllers and devices are
affected by this problem and trying to adding ATA_FLAG_DETECT_POLLING
for each such case is diffcult and not very rewarding.

This patch makes libata always use polling IDENTIFY.  This is
consistent with libata's original behavior and drivers/ide's behavior.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
      800b3996
    • T
      [PATCH] libata: prepare ata_sg_clean() for invocation from EH · 70e6ad0c
      由 Tejun Heo 提交于 
      Make ata_sg_clean() global and don't allow NCQ for internal commands.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      70e6ad0c
    • T
      [PATCH] libata: separate out rw ATA taskfile building into ata_build_rw_tf() · bd056d7e
      由 Tejun Heo 提交于 
      Separate out rw ATA taskfile building from ata_scsi_rw_xlat() into
ata_build_rw_tf().  This will be used to improve media error handling.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      bd056d7e
    • T
      [PATCH] libata: implement ata_exec_internal_sg() · 2432697b
      由 Tejun Heo 提交于 
      Sg'ify ata_exec_internal() and call it ata_exec_internal_sg().
Wrapper function around ata_exec_internal_sg() is implemented to
provide ata_exec_internal() interface.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      2432697b
    • T
      [PATCH] libata: make sure IRQ is cleared after ata_bmdma_freeze() · 0f0a3ad3
      由 Tejun Heo 提交于 
      Now that BMDMA status is recorded in irq handler.  ata_bmdma_freeze()
is free to manipulate host status.  Under certain circumstances, some
controllers (ICH7 in enhanced mode w/ IRQ shared) raise IRQ when CTL
register is written to and ATA_NIEN doesn't mask it.

This patch makes ata_bmdma_freeze() clear all pending IRQs after
freezing a port.  This change makes explicit clearing in
ata_device_add() unnecessary and thus kills it.  The removed code was
SFF-specific and was in the wrong place.

Note that ->freeze() handler is always called under ap->lock held and
irq disabled.  Even if CTL manipulation causes stuck IRQ, it's cleared
immediately.  This should be safe (enough) even in SMP environment.
More correct solution is to mask the IRQ from IRQ controller but that
would be an overkill.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      0f0a3ad3
    • T
      [PATCH] libata: move BMDMA host status recording from EH to interrupt handler · ea54763f
      由 Tejun Heo 提交于 
      For certain errors, interrupt handler alter BMDMA host status before
entering EH (clears active and intr).  Thus altered BMDMA host status
value is recorded by BMDMA EH and reported to user.  Move BMDMA host
status recording from EH to interrupt handler.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      ea54763f
    • T
      [PATCH] libata: implement ATA_FLAG_SETXFER_POLLING and use it in pata_via, take #2 · 3d3cca37
      由 Tejun Heo 提交于 
      This patch implements ATA_FLAG_SETXFER_POLLING and use in pata_via.
If this flag is set, transfer mode setting performed by polling not by
interrupt.  This should help those controllers which raise interrupt
before the command is actually complete on SETXFER.

Rationale for this approach.

* uses existing facility and relatively simple
* no busy sleep in the interrupt handler
* updating drivers is easy

While at it, kill now unused flag ATA_FLAG_SRST in pata_via.
Signed-off-by: NTejun Heo <htejun@gmail.com>
      3d3cca37
  15. 02 12月, 2006 13 次提交
  17. 22 11月, 2006 1 次提交
    • D
      WorkStruct: Pass the work_struct pointer instead of context data · 65f27f38
      由 David Howells 提交于 
      Pass the work_struct pointer to the work function rather than context data.
The work function can use container_of() to work out the data.

For the cases where the container of the work_struct may go away the moment the
pending bit is cleared, it is made possible to defer the release of the
structure by deferring the clearing of the pending bit.

To make this work, an extra flag is introduced into the management side of the
work_struct.  This governs auto-release of the structure upon execution.

Ordinarily, the work queue executor would release the work_struct for further
scheduling or deallocation by clearing the pending bit prior to jumping to the
work function.  This means that, unless the driver makes some guarantee itself
that the work_struct won't go away, the work function may not access anything
else in the work_struct or its container lest they be deallocated..  This is a
problem if the auxiliary data is taken away (as done by the last patch).

However, if the pending bit is *not* cleared before jumping to the work
function, then the work function *may* access the work_struct and its container
with no problems.  But then the work function must itself release the
work_struct by calling work_release().

In most cases, automatic release is fine, so this is the default.  Special
initiators exist for the non-auto-release case (ending in _NAR).
Signed-Off-By: NDavid Howells <dhowells@redhat.com>
      65f27f38