During hugepage map/unmap, TSB and TLB flushes are currently
issued at every PAGE_SIZE'd boundary which is unnecessary.
We now issue the flush at REAL_HPAGE_SIZE boundaries only.

Without this patch workloads which unmap a large hugepage
backed VMA region get CPU lockups due to excessive TLB
flush calls.

Orabug: 22365539, 22643230, 22995196
Signed-off-by: NNitin Gupta <nitin.m.gupta@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x).  This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.

Other use cases are for storing and retrieving data from the current
processors percpu area.  __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.

__get_cpu_var() is defined as :

#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))

__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.

this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.

This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset.  Thereby address calculations are avoided and less registers
are used when code is generated.

At the end of the patch set all uses of __get_cpu_var have been removed so
the macro is removed too.

The patch set includes passes over all arches as well. Once these operations
are used throughout then specialized macros can be defined in non -x86
arches as well in order to optimize per cpu access by f.e.  using a global
register that may be set to the per cpu base.

Transformations done to __get_cpu_var()

1. Determine the address of the percpu instance of the current processor.

	DEFINE_PER_CPU(int, y);
	int *x = &__get_cpu_var(y);

    Converts to

	int *x = this_cpu_ptr(&y);

2. Same as #1 but this time an array structure is involved.

	DEFINE_PER_CPU(int, y[20]);
	int *x = __get_cpu_var(y);

    Converts to

	int *x = this_cpu_ptr(y);

3. Retrieve the content of the current processors instance of a per cpu
variable.

	DEFINE_PER_CPU(int, y);
	int x = __get_cpu_var(y)

   Converts to

	int x = __this_cpu_read(y);

4. Retrieve the content of a percpu struct

	DEFINE_PER_CPU(struct mystruct, y);
	struct mystruct x = __get_cpu_var(y);

   Converts to

	memcpy(&x, this_cpu_ptr(&y), sizeof(x));

5. Assignment to a per cpu variable

	DEFINE_PER_CPU(int, y)
	__get_cpu_var(y) = x;

   Converts to

	__this_cpu_write(y, x);

6. Increment/Decrement etc of a per cpu variable

	DEFINE_PER_CPU(int, y);
	__get_cpu_var(y)++

   Converts to

	__this_cpu_inc(y)

Cc: sparclinux@vger.kernel.org
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NChristoph Lameter <cl@linux.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

On sparc64 "present" and "valid" are seperate PTE bits, this allows us to
naturally distinguish between the user explicitly asking for PROT_NONE
with mprotect() and other situations.

However we weren't handling this properly in the huge PMD paths.

First of all, the page table walker in the TSB miss path only checks
for _PAGE_PMD_HUGE.  So the generic pmdp_invalidate() would clear
_PAGE_PRESENT but the TLB miss paths would still load it into the TLB
as a valid huge PMD.

Fix this by clearing the valid bit in pmdp_invalidate(), and also
checking the valid bit in USER_PGTABLE_CHECK_PMD_HUGE using "brgez"
since _PAGE_VALID is bit 63 in both the sun4u and sun4v pte layouts.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This code was mistakenly using the exec bit from the PMD in all
cases, even when the PMD isn't a huge PMD.

If it's not a huge PMD, test the exec bit in the individual ptes down
in tlb_batch_pmd_scan().
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently mm->pmd_huge_pte protected by page table lock.  It will not
work with split lock.  We have to have per-pmd pmd_huge_pte for proper
access serialization.

For now, let's just introduce wrapper to access mm->pmd_huge_pte.
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Tested-by: NAlex Thorlton <athorlton@sgi.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Eric W . Biederman" <ebiederm@xmission.com>
Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Robin Holt <robinmholt@gmail.com>
Cc: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that we have 64-bits for PMDs we can stop using special encodings
for the huge PMD values, and just put real PTEs in there.

We allocate a _PAGE_PMD_HUGE bit to distinguish between plain PMDs and
huge ones.  It is the same for both 4U and 4V PTE layouts.

We also use _PAGE_SPECIAL to indicate the splitting state, since a
huge PMD cannot also be special.

All of the PMD --> PTE translation code disappears, and most of the
huge PMD bit modifications and tests just degenerate into the PTE
operations.  In particular USER_PGTABLE_CHECK_PMD_HUGE becomes
trivial.

As a side effect, normal PMDs don't shift the physical address around.
This also speeds up the page table walks in the TLB miss paths since
they don't have to do the shifts any more.

Another non-trivial aspect is that pte_modify() has to be changed
to preserve the _PAGE_PMD_HUGE bits as well as the page size field
of the pte.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The impetus for this is that we would like to move to 64-bit PMDs and
PGDs, but that would result in only supporting a 42-bit address space
with the current page table layout.  It'd be nice to support at least
43-bits.

The reason we'd end up with only 42-bits after making PMDs and PGDs
64-bit is that we only use half-page sized PTE tables in order to make
PMDs line up to 4MB, the hardware huge page size we use.

So what we do here is we make huge pages 8MB, and fabricate them using
4MB hw TLB entries.

Facilitate this by providing a "REAL_HPAGE_SHIFT" which is used in
places that really need to operate on hardware 4MB pages.

Use full pages (512 entries) for PTE tables, and adjust PMD_SHIFT,
PGD_SHIFT, and the build time CPP test as needed.  Use a CPP test to
make sure REAL_HPAGE_SHIFT and the _PAGE_SZHUGE_* we use match up.

This makes the pgtable cache completely unused, so remove the code
managing it and the state used in mm_context_t.  Now we have less
spinlocks taken in the page table allocation path.

The technique we use to fabricate the 8MB pages is to transfer bit 22
from the missing virtual address into the PTEs physical address field.
That takes care of the transparent huge pages case.

For hugetlb, we fill things in at the PTE level and that code already
puts the sub huge page physical bits into the PTEs, based upon the
offset, so there is nothing special we need to do.  It all just works
out.

So, a small amount of complexity in the THP case, but this code is
about to get much simpler when we move the 64-bit PMDs as we can move
away from the fancy 32-bit huge PMD encoding and just put a real PTE
value in there.

With bug fixes and help from Bob Picco.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will be later used by powerpc THP support.  In powerpc we want to use
pgtable for storing the hash index values.  So instead of adding them to
mm_context list, we would like to store them in the second half of pmd
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: NAndrea Arcangeli <aarcange@redhat.com>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This fixes a race where a cpu may re-load a tlb from a stale tsb right
after it has been flushed by a remote function call.

I still see some instability when stressing the system with parallel
kernel builds while creating memory pressure by writing to
/proc/sys/vm/nr_hugepages, but this patch improves the stability
significantly.
Signed-off-by: NDave Kleikamp <dave.kleikamp@oracle.com>
Acked-by: NBob Picco <bob.picco@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Dave Kleikamp, when we emit cross calls to do batched
TLB flush processing we have a race because we do not synchronize on
the sibling cpus completing the cross call.

So meanwhile the TLB batch can be reset (tb->tlb_nr set to zero, etc.)
and either flushes are missed or flushes will flush the wrong
addresses.

Fix this by using generic infrastructure to synchonize on the
completion of the cross call.

This first required getting the flush_tlb_pending() call out from
switch_to() which operates with locks held and interrupts disabled.
The problem is that smp_call_function_many() cannot be invoked with
IRQs disabled and this is explicitly checked for with WARN_ON_ONCE().

We get the batch processing outside of locked IRQ disabled sections by
using some ideas from the powerpc port. Namely, we only batch inside
of arch_{enter,leave}_lazy_mmu_mode() calls.  If we're not in such a
region, we flush TLBs synchronously.

1) Get rid of xcall_flush_tlb_pending and per-cpu type
   implementations.

2) Do TLB batch cross calls instead via:

	smp_call_function_many()
		tlb_pending_func()
			__flush_tlb_pending()

3) Batch only in lazy mmu sequences:

	a) Add 'active' member to struct tlb_batch
	b) Define __HAVE_ARCH_ENTER_LAZY_MMU_MODE
	c) Set 'active' in arch_enter_lazy_mmu_mode()
	d) Run batch and clear 'active' in arch_leave_lazy_mmu_mode()
	e) Check 'active' in tlb_batch_add_one() and do a synchronous
           flush if it's clear.

4) Add infrastructure for synchronous TLB page flushes.

	a) Implement __flush_tlb_page and per-cpu variants, patch
	   as needed.
	b) Likewise for xcall_flush_tlb_page.
	c) Implement smp_flush_tlb_page() to invoke the cross-call.
	d) Wire up global_flush_tlb_page() to the right routine based
           upon CONFIG_SMP

5) It turns out that singleton batches are very common, 2 out of every
   3 batch flushes have only a single entry in them.

   The batch flush waiting is very expensive, both because of the poll
   on sibling cpu completeion, as well as because passing the tlb batch
   pointer to the sibling cpus invokes a shared memory dereference.

   Therefore, in flush_tlb_pending(), if there is only one entry in
   the batch perform a completely asynchronous global_flush_tlb_page()
   instead.
Reported-by: NDave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NDave Kleikamp <dave.kleikamp@oracle.com>

If our first THP installation for an MM is via the set_pmd_at() done
during khugepaged's collapsing we'll end up in tsb_grow() trying to do
a GFP_KERNEL allocation with several locks held.

Simply using GFP_ATOMIC in this situation is not the best option
because we really can't have this fail, so we'd really like to keep
this an order 0 GFP_KERNEL allocation if possible.

Also, doing the TSB allocation from khugepaged is a really bad idea
because we'll allocate it potentially from the wrong NUMA node in that
context.

So what we do is defer the hugepage TSB allocation until the first TLB
miss we take on a hugepage.  This is slightly tricky because we have
to handle two unusual cases:

1) Taking the first hugepage TLB miss in the window trap handler.
   We'll call the winfix_trampoline when that is detected.

2) An initial TSB allocation via TLB miss races with a hugetlb
   fault on another cpu running the same MM.  We handle this by
   unconditionally loading the TSB we see into the current cpu
   even if it's non-NULL at hugetlb_setup time.
Reported-by: NMeelis Roos <mroos@ut.ee>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is relatively easy since PMD's now cover exactly 4MB of memory.

Our PMD entries are 32-bits each, so we use a special encoding.  The
lowest bit, PMD_ISHUGE, determines the interpretation.  This is possible
because sparc64's page tables are purely software entities so we can use
whatever encoding scheme we want.  We just have to make the TLB miss
assembler page table walkers aware of the layout.

set_pmd_at() works much like set_pte_at() but it has to operate in two
page from a table of non-huge PTEs, so we have to queue up TLB flushes
based upon what mappings are valid in the PTE table.  In the second regime
we are going from huge-page to non-huge-page, and in that case we need
only queue up a single TLB flush to push out the huge page mapping.

We still have 5 bits remaining in the huge PMD encoding so we can very
likely support any new pieces of THP state tracking that might get added
in the future.

With lots of help from Johannes Weiner.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Rework the sparc mmu_gather usage to conform to the new world order :-)

Sparc mmu_gather does two things:
 - tracks vaddrs to unhash
 - tracks pages to free

Split these two things like powerpc has done and keep the vaddrs
in per-cpu data structures and flush them on context switch.

The remaining bits can then use the generic mmu_gather.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: NDavid Miller <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Tony Luck <tony.luck@intel.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- move all sparc64/mm/ files to arch/sparc/mm/
- commonly named files are named _64.c
- add files to sparc/mm/Makefile preserving link order
- delete now unused sparc64/mm/Makefile
- sparc64 now finds mm/ in sparc
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was just needed to work around an ancient gcc bug that
we don't care about any more.

It was also causing a sparse warnings:

arch/sparc64/mm/tlb.c:22:52: warning: Using plain integer as NULL pointer
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Noticed by Andrew Morton.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported by Mariusz Kozlowski.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A context switch will force a call to flush_tlb_pending() (via
switch_to()), so if we test tlb_nr to be non-zero, then sleep, it
would become zero and later back at the original context we'll pass
zero down into the TLB flushing code which should never see a nr
argument of zero.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is totally wasted work, since we have no D-cache aliasing
issues on sun4v.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We now use the TSB hardware assist features of the UltraSPARC
MMUs.

SMP is currently knowingly broken, we need to find another place
to store the per-cpu base pointers.  We hid them away in the TSB
base register, and that obviously will not work any more :-)

Another known broken case is non-8KB base page size.

Also noticed that flush_tlb_all() is not referenced anywhere, only
the internal __flush_tlb_all() (local cpu only) is used by the
sparc64 port, so we can get rid of flush_tlb_all().

The kernel gets it's own 8KB TSB (swapper_tsb) and each address space
gets it's own private 8K TSB.  Later we can add code to dynamically
increase the size of per-process TSB as the RSS grows.  An 8KB TSB is
good enough for up to about a 4MB RSS, after which the TSB starts to
incur many capacity and conflict misses.

We even accumulate OBP translations into the kernel TSB.

Another area for refinement is large page size support.  We could use
a secondary address space TSB to handle those.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

zap_pte_range has been counting the pages it frees in tlb->freed, then
tlb_finish_mmu has used that to update the mm's rss.  That got stranger when I
added anon_rss, yet updated it by a different route; and stranger when rss and
anon_rss became mm_counters with special access macros.  And it would no
longer be viable if we're relying on page_table_lock to stabilize the
mm_counter, but calling tlb_finish_mmu outside that lock.

Remove the mmu_gather's freed field, let tlb_finish_mmu stick to its own
business, just decrement the rss mm_counter in zap_pte_range (yes, there was
some point to batching the update, and a subsequent patch restores that).  And
forget the anal paranoia of first reading the counter to avoid going negative
- if rss does go negative, just fix that bug.

Remove the mmu_gather's flushes and avoided_flushes from arm and arm26: no use
was being made of them.  But arm26 alone was actually using the freed, in the
way some others use need_flush: give it a need_flush.  arm26 seems to prefer
spaces to tabs here: respect that.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

tlb_is_full_mm?  What does that mean?  The TLB is full?  No, it means that the
mm's last user has gone and the whole mm is being torn down.  And it's an
inline function because sparc64 uses a different (slightly better)
"tlb_frozen" name for the flag others call "fullmm".

And now the ptep_get_and_clear_full macro used in zap_pte_range refers
directly to tlb->fullmm, which would be wrong for sparc64.  Rather than
correct that, I'd prefer to scrap tlb_is_full_mm altogether, and change
sparc64 to just use the same poor name as everyone else - is that okay?
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!