The KSZ8021 PHY was previously caught by KS8051, which is not correct.
This PHY needs additional setup if it is strapped for address 0. In such
case an reserved bit must be written in the 0x16, "Operation Mode Strap
Override" register. According to the KS8051 datasheet, that bit means
"PHY Address 0 in non-broadcast" and it indeed behaves as such on KSZ8021.
The issue where the ethernet controller (Freescale FEC) did not communicate
with network is fixed by writing this bit as 1.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If registering of one of them fails, all already registered drivers
of this module will be unregistered.

Use the new register/unregister functions in all drivers
registering more than one driver.

amd.c, realtek.c: Simplify: directly return registration result.

Tested with broadcom.c
All others compile-tested.
Signed-off-by: NChristian Hohnstaedt <chohnstaedt@innominate.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On a freescale imx6q platform, a hardware phy chip KSZ9021 is
recognized as a KS8001 chip by the current driver like this:
eth0: Freescale FEC PHY driver [Micrel KS8001 or KS8721]

KSZ9021 has phy_id 0x00221610, while KSZ8001 has phy_id
0x0022161a, the current phy_id_mask (0x00fffff0/0x00ffff10) can't
distinguish them. So change phy_id_mask to resolve this problem.

Although the micrel datasheet says that the 4 LSB of phyid2 register
contains the chip revision number and the current driver is designed
to follow this rule, in reality the chip implementation doesn't follow
it.

Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NHui Wang <jason77.wang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Platform code can now set the MICREL_PHY_50MHZ_CLK bit of dev_flags in a fixup
routine (registered with phy_register_fixup_for_uid()), to make the KZS8051RNL
PHY work with 50MHz RMII reference clock.

Cc: David J. Choi <david.choi@micrel.com>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MODULE_DEVICE_TABLE only expands to something if it's compiled
for a module.  So when building-in support for the phys, the
mdio_device_id tables are unused.  Marking them with __maybe_unused
fixes the following warnings:

	drivers/net/phy/bcm63xx.c:134: warning: 'bcm63xx_tbl' defined but not used
	drivers/net/phy/broadcom.c:933: warning: 'broadcom_tbl' defined but not used
	drivers/net/phy/cicada.c:162: warning: 'cicada_tbl' defined but not used
	drivers/net/phy/davicom.c:222: warning: 'davicom_tbl' defined but not used
	drivers/net/phy/et1011c.c:114: warning: 'et1011c_tbl' defined but not used
	drivers/net/phy/icplus.c:137: warning: 'icplus_tbl' defined but not used
	drivers/net/phy/lxt.c:226: warning: 'lxt_tbl' defined but not used
	drivers/net/phy/marvell.c:724: warning: 'marvell_tbl' defined but not used
	drivers/net/phy/micrel.c:234: warning: 'micrel_tbl' defined but not used
	drivers/net/phy/national.c:154: warning: 'ns_tbl' defined but not used
	drivers/net/phy/qsemi.c:141: warning: 'qs6612_tbl' defined but not used
	drivers/net/phy/realtek.c:82: warning: 'realtek_tbl' defined but not used
	drivers/net/phy/smsc.c:257: warning: 'smsc_tbl' defined but not used
	drivers/net/phy/ste10Xp.c:135: warning: 'ste10Xp_tbl' defined but not used
	drivers/net/phy/vitesse.c:195: warning: 'vitesse_tbl' defined but not used
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hello all:

This patch fixes what Ben mentioned, namely duplicated ids.

From: David J. Choi <david.choi@micrel.com>

Body of the explanation: This patch has changes as followings;
 -support the interrupt from phy devices from Micrel Inc.
 -support more phy devices, ks8737, ks8721, ks8041, ks8051 from Micrel.
 -remove vsc8201 because this device was used only internal test at Micrel.
Signed-off-by: NDavid J. Choi <david.choi@micrel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Missing name string in ks8001_driver, so we crash on register.
Reported-by: NIngo Molnar <mingo@elte.hu>
Tested-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the first version of phy driver from Micrel Inc.
Signed-off-by: NDavid J. Choi <david.choi@micrel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>