The rxdone_entry_desc structure contains 3 fields
which are always 1 or 0. We can safe 8 bytes by
replacing them with a single dev_flags fields which
contain the flags for those settings.

Additionally we can remove the OFDM flag since it
is no longer used since the introduction of the
SIGNAL_PLCP flag.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only rt2400pci can have the preamble bit set in the PLCP value,
for all other drivers it should not be cleared since that will
conflict with the plcp values for OFDM rates.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Version bump to 2.1.4
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After sampling hundreds of RX frame descriptors,
the results were conclusive:
- The Ralink documentation regarding the SIGNAL and RSSI are wrong.

It turns out that of the 5 BBR registers, we should not use BBR0 and BBR1
for SIGNAL and RSSI respectively, but actually BBR1 and BBR2.
BBR0 does show values, but the exact meaning remains unclear,
but they cannot be translated into a SIGNAL or RSSI field.
BBR3, BBR4 and BBR5 are always 0, so their meaning is unknown.

As it turns out, the reported SIGNAL is the PLCP value, this
in contradiction to what was expected looking at rt2500pci which
only reported the PLCP values for OFDM rates and bitrate values
for CCK rates.

This means we should let the driver raise the flag about the contents
of the SIGNAL field so rt2x00lib can always do the right thing based
on what the driver reports.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Due to a terrible typo the RX DMA base address
was initialized to the beacon base address.
Obviously bad things happen with bugs like that....
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The basic rate which is configured in the register
should not match all supported rates, but only the _basic_ rates.

Fix this by adding a new flag to the rt2x00_rate structure
and whenever the mode is changed, loop over all available rates
for that band to get the basic rate mask.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whatever mode we are in, according to the legacy drivers
we should always enable TSF ticking/counting.
We should also always enable the TBCN/TBTT field,
this field is only disabled during beacon regeneration.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00dev isn't interested in the rt2x00leds_register() value
anyway. So lets make it return void to even prevent people from
assuming there is anybody interested in the returnvalue.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rename config_preamble() to config_erp() and cleanup argument
list by putting it all into a single structure.
This will make the function more meaningful and easier to
expand later. This second option is mostly intended to make
the patch "mac80211: proper short-slot handling" from Johannes Berg
easier to apply for rt2x00.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When mac sets the IEEE80211_TXCTL_SEND_AFTER_DTIM flag, we should
check if the ATIM queue is available in the driver and put the
frame in that queue for proper behavior (send frame after beacon interval).
Unfortunately not all drivers have this ATIM queue, and will lack
this feature for now.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00lib should filter SW diversity out before sending any configuration
changes to the driver. When rt2x00lib fails to do this, it is important
that such events are reported because it _must_ be fixed.
So upgrading the error level to a BUG_ON() which will make sure
this bug gets noticed whenever it happens.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00lib depended on 2 crc algorithms because rt61/rt73
use a different algorithm then rt2800. This means that
even when only 1 algorithm was needed, the dependency was
still present for both.
By moving the checksum generation to the driver we can clean
up 2 annoying flags (which indicated which checksum was required)
and move the dependency to where it belongs: the driver.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The queue->lock could be grabbed from interrupt context,
which could lead to lockdep panic like this:

kernel: ======================================================
kernel: [ INFO: soft-safe -> soft-unsafe lock order detected ]
kernel: 2.6.25-0.95.rc4.fc9 #1
kernel: ------------------------------------------------------
kernel: rt2500pci/1251 [HC0[0]:SC0[1]:HE1:SE0] is trying to acquire:
kernel:  (&queue->lock){--..}, at: [<ffffffff88213339>] rt2x00queue_get_entry+0x5a/0x81 [rt2x00lib]
kernel:
kernel: and this task is already holding:
kernel:  (_xmit_IEEE80211){-...}, at: [<ffffffff8122e9a3>] __qdisc_run+0x84/0x1a9
kernel: which would create a new lock dependency:
kernel:  (_xmit_IEEE80211){-...} -> (&queue->lock){--..}
kernel:
kernel: but this new dependency connects a soft-irq-safe lock:
kernel:  (_xmit_ETHER){-+..}
kernel: ... which became soft-irq-safe at:
kernel:   [<ffffffffffffffff>] 0xffffffffffffffff
kernel:
kernel: to a soft-irq-unsafe lock:
kernel:  (&queue->lock){--..}
kernel: ... which became soft-irq-unsafe at:
kernel: ...  [<ffffffff810545a2>] __lock_acquire+0x62d/0xd63
kernel:   [<ffffffff81054d36>] lock_acquire+0x5e/0x78
kernel:   [<ffffffff812a1497>] _spin_lock+0x26/0x53
kernel:   [<ffffffff88212f98>] rt2x00queue_reset+0x16/0x40 [rt2x00lib]
kernel:   [<ffffffff88212fd4>] rt2x00queue_alloc_entries+0x12/0xab [rt2x00lib]
kernel:   [<ffffffff88213091>] rt2x00queue_initialize+0x24/0xf2 [rt2x00lib]
kernel:   [<ffffffff88212036>] rt2x00lib_start+0x3b/0xd4 [rt2x00lib]
kernel:   [<ffffffff88212609>] rt2x00mac_start+0x18/0x1a [rt2x00lib]
kernel:   [<ffffffff881b9a4b>] ieee80211_open+0x1f3/0x46d [mac80211]
kernel:   [<ffffffff8121d980>] dev_open+0x4d/0x8b
kernel:   [<ffffffff8121d41e>] dev_change_flags+0xaf/0x172
kernel:   [<ffffffff81224fc2>] do_setlink+0x276/0x338
kernel:   [<ffffffff81225198>] rtnl_setlink+0x114/0x116
kernel:   [<ffffffff812262fc>] rtnetlink_rcv_msg+0x1d8/0x1f9
kernel:   [<ffffffff8123649a>] netlink_rcv_skb+0x3e/0xac
kernel:   [<ffffffff8122611a>] rtnetlink_rcv+0x29/0x33
kernel:   [<ffffffff81235eed>] netlink_unicast+0x1fe/0x26b
kernel:   [<ffffffff81236224>] netlink_sendmsg+0x2ca/0x2dd
kernel:   [<ffffffff812103b3>] sock_sendmsg+0xfd/0x120
kernel:   [<ffffffff812105a8>] sys_sendmsg+0x1d2/0x23c
kernel:   [<ffffffff8100c1c7>] tracesys+0xdc/0xe1
kernel:   [<ffffffffffffffff>] 0xffffffffffffffff

This can be fixed by using the irqsave/irqrestore versions
during the queue->lock handling.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix trivial log message.
Signed-off-by: NLuis Correia <luis.f.correia@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When fixing up the packet alignment, if we had to add 2 bytes to the front of
the skb we need to remember to take them off the end afterwards. This fixes
reception of encrypted packets which were otherwise failing with an invalid
ICV.
Signed-off-by: NAdam Baker <linux@baker-net.org.uk>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We should not write 0 to the beacon sync register during
config_intf() since that will clear out the beacon interval
and forces the beacon to be send out at the lowest interval.
(reported by Mattias Nissler).

The side effect of the same bug was that while working with
multiple virtual AP interfaces a change for any of those
interfaces would disable beaconing untill an beacon update
was provided.

This is resolved by only updating the TSF_SYNC value during
config_intf(). In update_beacon() we disable beaconing
temporarily to prevent fake beacons to be transmitted.
Finally kick_tx_queue() will enable beaconing again.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In rt2x00lib_write_tx_desc() the skb->data and skb->len fields
were incorrectly used. For USB drivers both of those values
contain invalid data (skb->data points to the device descriptor,
skb->len contains the frame _and_ descriptor length).

Instead of using the skbuffer fields we should use the skbdesc
fields which are correctly initialized and contain all the data
that we need.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rxdesc->size is unitialized before the desriptor has been read.
Move the truncation of the sk buffer to the moment all variables
have been initialized.
Signed-off-by: NMattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

skbdesc->desc_len is uninitialized at the start
of the function. So it is a _bad_ idea to use it...
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The sizeof() operator was incorrectly applied to the pointer, not the struct.
Signed-off-by: NMattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the TX path, the driver didn't copy the TX control data structure. Thus, it
was invalid in the TX done handler, causing serious trouble and misbehaviour.
Signed-off-by: NMattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some architectures give problems when reading
RX frame descriptor words when the descriptor
is not aligned on a 4 byte boundrary.

Due to optimalizations for the ieee80211 payload
4 byte alignment, it is no longer guarenteed
that the descriptor is placed on the 4 byte
boundrary (In fact, for rt73usb it is absolutely
never aligned to 4 bytes, for rt2500usb it depends
on the length of the payload).

This will copy the descriptor to a 4 byte aligned
location before it is read for the first time.
This will also move the payload data alignment
in rt2x00usb (instead of inside the driver) where
it has always belonged.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add suspend/resume handlers to rt2x00rfkill to have it stop
the input-polldev and prevent it from calling rt2x00 during
suspend period. This could lead to a NULL pointer fault when
rt2x00 suspended, but polldev send a request, because
the csr_addr is NULL.

Also don't let the rfkill allocation/registration block
the initialization of the entire device. Just print a warning
and continue as if nothing happened.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On rt73 and rt61 disabling reception of multicast packets also disables
broadcast traffic which we never want to do. Therefore we should never
disable multicast.
Signed-off-by: NAdam Baker <linux@baker-net.org.uk>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a typo in the link tuner where accidently the
2GHz band was checked instead of the 5GHz band.
This forced the link tuner to work in an invalid
range for the currently active band.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The MAC address offset defines were incorrect because
the byte offset was used instead of word index. This
bug had no affect on normal operations since these
defines weren't used. (EEPROM_MAC_ADDR_0 was used
to read 6 bytes from).
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The supported_bands field of struct hw_mode_spec now represents a bitfield,
so bitfield operators need to be tested with when setting the band data.

The current code generates the following warning:

[176624.986244] WARNING: at /usr/local/src/incoming/compat-wireless-2.6/net/wireless/core.c:269 wiphy_register()
[176624.986249] Pid: 12548, comm: modprobe Tainted: P        2.6.24.2#4
[176624.986251]
[176624.986251] Call Trace:
[176624.986277]  [<ffffffff881c56bf>] :cfg80211:wiphy_register+0x17f/0x1a0
[176624.986282]  [<ffffffff881ddf80>] :rt61pci:rt61pci_eepromregister_write+0x0/0x80
[176624.986302]  [<ffffffff88b7e4bc>] :mac80211:ieee80211_register_hw+0x2c/0x2b0
[176624.986310]  [<ffffffff881cdc80>] :rt2x00lib:rt2x00lib_probe_dev+0x350/0x3f0
[176624.986318]  [<ffffffff881d74b9>] :rt2x00pci:rt2x00pci_probe+0x149/0x200
[176624.986325]  [<ffffffff8030c858>] pci_device_probe+0xf8/0x170
[176624.986331]  [<ffffffff803594fc>] driver_probe_device+0x9c/0x1c0
[176624.986335]  [<ffffffff80359700>] __driver_attach+0x0/0xb0
[176624.986337]  [<ffffffff803597a5>] __driver_attach+0xa5/0xb0
[176624.986341]  [<ffffffff8035877d>] bus_for_each_dev+0x4d/0x80
[176624.986347]  [<ffffffff80358b8c>] bus_add_driver+0xac/0x210
[176624.986351]  [<ffffffff8030cad3>] __pci_register_driver+0x73/0xc0
[176624.986357]  [<ffffffff8025689e>] sys_init_module+0x18e/0x1a20
[176624.986374]  [<ffffffff8020c42e>] system_call+0x7e/0x83
Signed-off-by: NGertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The async vendor requests are a ugly hack which is not working correctly.
The proper fix for the scheduling while atomic issue is finding out why
we can't use led classes for USB drivers and fix that.

Just replace all async calls with the regular ones and print an
error for the disallowed LED configuration attempts. That will
help in determining which led class is causing the problem.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't wildly pass any number for num_rates to rt2x00lib,
instead pass which type of rates are supported (CCK, OFDM).
Same for num_modes but then for the 2GHZ and 5GHZ band.

This makes the interface look much nicer and makes
extending it later easier.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The dscape stack was renamed to mac80211 a long time ago,
we are long overdue with fixing all comments to reflect this.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Specifications indicate the TSF registers are read-only,
so there is no point in writing 0 to those registers.

As far as I know there isn't another way to reset the
TSF registers. So removing these callbacks will notify
mac80211 about the lack of support.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As Adam Baker reported the DMA address for the
descriptor base was incorrectly initialized in
the PCI drivers.

Instead of the DMA base for the descriptor, the
DMA base for the data was passed resulting in a
broken TX/RX state for PCI drivers.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ACK_CTS frame is a control frame, this means
dropping the frame depends on the FIF_CONTROL flag
for filtering.

This also fixes an obvious typo in register definition.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds a new flag for the skb_frame_desc structure which is used to tag
rts/cts frames that are generated by the driver. Through the tag we can
recognize frames we have generated ourselves, so we don't report their tx
status to mac80211.

This patch is based on the original patch by
Mattias Nissler <mattias.nissler@gmx.de>.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 sends the txpower to use during config(),
we already store it in the rt2x00_dev structure.
When writing the descriptor correctly initialize
the txpower field with this value to make sure
all frames are send out with the correct tx power.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>