* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  acpi-wmi: unsigned cannot be less than 0
  thinkpad-acpi: fix module autoloading for older models
  acer-wmi: Unmark as 'experimental'
  acpi-wmi: Unmark as 'experimental'
  acer-wmi: double free in acer_rfkill_exit()
  platform/x86: depends instead of select for laptop platform drivers
  asus-laptop: use select instead of depends on
  eeepc-laptop: restore acpi_generate_proc_event()
  asus-laptop: restore acpi_generate_proc_event()
  acpi: check for pxm_to_node_map overflow
  ACPI: remove doubled status checking
  ACPI suspend: Blacklist Toshiba Satellite L300 that requires to set SCI_EN directly on resume
  Revert "ACPI: make some IO ports off-limits to AML"
  suspend: switch the Asus Pundit P1-AH2 to old ACPI sleep ordering

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
  r8169: revert "r8169: read MAC address from EEPROM on init (2nd attempt)"
  r8169: use hardware auto-padding.
  igb: remove ASPM L0s workaround
  netxen: remove old flash check.
  mv643xx_eth: fix unicast address filter corruption on mtu change
  xfrm: Fix xfrm_state_find() wrt. wildcard source address.
  emac: Fix clock control for 405EX and 405EXr chips
  ixgbe: fix multiple unicast address support
  via-velocity: Fix DMA mapping length errors on transmit.
  qlge: bugfix: Pad outbound frames smaller than 60 bytes.
  qlge: bugfix: Move netif_napi_del() to common call point.
  qlge: bugfix: Tell hw to strip vlan header.
  qlge: bugfix: Increase filter on inbound csum.
  dnet: replace obsolete *netif_rx_* functions with *napi_*
  net: Add be2net driver.
  dnet: Fix warnings on 64-bit.
  dnet: Dave DNET ethernet controller driver (updated)
  ipv6:  Fix BUG when disabled ipv6 module is unloaded
  bnx2x: Using DMAE to initialize the chip
  bnx2x: Casting page alignment
  ...

Impact: help prevent extinction of species

The Tasmanian Devil is a shy iconic Australian creature named for its
spine-chilling screech.  It is threatened with extinction due to a
scientifically interesting but horrific transmissible facial cancer.

This one is standing in for Tux for one release using the far less-known
Devil Facial Tux Disguise.

	Save The Tasmanian Devil http://tassiedevil.com.auSigned-off-by: NLinux.conf.au Hobart Team <contact@marchsouth.org>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

filp->f_pos only get updated at the end of the function. Thus d_off of those
dirents who are in the middle will be 0, and this will cause a problem in
glibc's readdir implementation, specifically endless loop. Because when overflow
occurs, f_pos will be set to next dirent to read, however it will be 0, unless
the next one is the last one. So it will start over again and again.

There is a sample program in man 2 gendents. This is the output of the program
running on a multithread program's task dir before this patch is applied:

  $ ./a.out /proc/3807/task
  --------------- nread=128 ---------------
  i-node#  file type  d_reclen  d_off   d_name
    506442  directory    16          1  .
    506441  directory    16          0  ..
    506443  directory    16          0  3807
    506444  directory    16          0  3809
    506445  directory    16          0  3812
    506446  directory    16          0  3861
    506447  directory    16          0  3862
    506448  directory    16          8  3863

This is the output after this patch is applied

  $ ./a.out /proc/3807/task
  --------------- nread=128 ---------------
  i-node#  file type  d_reclen  d_off   d_name
    506442  directory    16          1  .
    506441  directory    16          2  ..
    506443  directory    16          3  3807
    506444  directory    16          4  3809
    506445  directory    16          5  3812
    506446  directory    16          6  3861
    506447  directory    16          7  3862
    506448  directory    16          8  3863
Signed-off-by: NZhang Le <r0bertz@gentoo.org>
Acked-by: NAl Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

include/linux/pci-acpi.h:74:

typedef u32                 acpi_status;

result is unsigned, so an error returned by acpi_bus_register_driver()
will not be noticed.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

Looking at the source, there seems to be a missing * to match my DMI
string.  I mean for newer IBM and Lenovo's laptops you match either one
of the following:
MODULE_ALIAS("dmi:bvnIBM:*:svnIBM:*:pvrThinkPad*:rvnIBM:*");
MODULE_ALIAS("dmi:bvnLENOVO:*:svnLENOVO:*:pvrThinkPad*:rvnLENOVO:*");

While for older Thinkpads, you do this (for instance):
IBM_BIOS_MODULE_ALIAS("1[0,3,6,8,A-G,I,K,M-P,S,T]");

with IBM_BIOS_MODULE_ALIAS being MODULE_ALIAS("dmi:bvnIBM:bvr" __type "ET??WW")

Note there's no * terminating the string.  As result, udev doesn't load
anything because modprobe cannot find anything matching this (my
machine actually):

udevtest: run: '/sbin/modprobe dmi:bvnIBM:bvr1IET71WW(2.10):bd06/16/2006:svnIBM:pn236621U:pvrNotAv
Signed-off-by: NMathieu Chouquet-Stringer <mchouque@free.fr>
Acked-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

This driver has been around and used long enough that we can drop the
'experimental'.
Signed-off-by: NCarlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: NLen Brown <len.brown@intel.com>

ACPI-WMI isn't experimental anymore, and there are other drivers that now
depend on it that aren't either.
Signed-off-by: NCarlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: NLen Brown <len.brown@intel.com>

This is acer_rfkill_exit() from drivers/platform/x86/acer-wmi.c.

The code frees wireless_rfkill->data again instead of
bluetooth_rfkill->data.

This was found using a code checker (http://repo.or.cz/w/smatch.git/).
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NCarlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: NLen Brown <len.brown@intel.com>

"I hate `select' and will gleefully leap on any s/select/depends/ patch,
whether it works or not :)"
  Andrew Morton

select INPUT is not needed here, because if someone doesn't want INPUT,
he won't want these drivers either.
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

Like thinkpad_acpi or eeepc-laptop, asus-laptop will
now use "select" instead of "depends on"
for LEDS_CLASS, NEW_LEDS and BACKLIGHT_CLASS_DEVICE
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

Restore acpi_generate_proc_event() for backward
compatibility with old acpi scripts.
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

Restore acpi_generate_proc_event() for backward
compatibility with old acpi scripts.
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

It is hardly (if ever) possible but in case of broken _PXM entry we could
reach out of pxm_to_node_map array bounds in acpi_map_pxm_to_node() call.
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

There was a misplaced status test (two consequent tests without a
statement in between) in acpi_bus_init for ages.  Remove it, since the
function which should be checked (acpi_os_initialize1) has BUG_ONs on
failure paths.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

This is a supplement of commit 65df7847.
http://bugzilla.kernel.org/show_bug.cgi?id=12798Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This reverts commit 5ec5d38a.
because it caused spurious dmesg warmings.
We'll implement the check for off-limit ports
in a more clever way in the future.

http://bugzilla.kernel.org/show_bug.cgi?id=12758Signed-off-by: NLen Brown <len.brown@intel.com>

Switch the Asus Pundit P1-AH2 (M2N8L motherboard) to the old ACPI 1.0
sleep ordering by default.  Without this it will not suspend/resume
correctly.
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Tested-by: NDustin Kirkland <kirkland@canonical.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

It fails on the following systems:
- RTL8169sc/8110sc (XID 18000000)
  reported by Tim Durack <tdurack@gmail.com> (x86)
- RTL8169sb/8110sb (XID 10000000)
  reported by Mikael Pettersson <mikpe@it.uu.se> (ARM)

The patch appeared to work on x86 for the following systems:
RTL8169sb/8110sb 10000000 PCI   (EXT)
RTL8110s         04000000 PCI   (EXT)
RTL8102e         24a00000 PCI-E (LOM)
RTL8168c/8111c   3c2000c0 PCI-E (LOM)
RTL8168b/8111b   38000000 PCI-E (LOM)
RTL8168b/8111b   38000000 PCI-E (EXT)

The patch exposes two problems:
1) while not completely wrong, mac addresses are not read correctly
   from the EEPROM
2) the MAC address registers are not correctly set
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Tested-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It shortens the code and fixes the current pci_unmap leak with
padded skb reported by Dave Jones.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CC      drivers/parisc/sba_iommu.o
drivers/parisc/sba_iommu.c:1373: error: expected identifier or '('
before '}' token
make[2]: *** [drivers/parisc/sba_iommu.o] Error 1
make[1]: *** [drivers/parisc] Error 2
make: *** [drivers] Error 2

Don't know how this has gone missed for so long... clearly I need
to do builds on my C8000 more often.
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/home/rmk/linux-2.6-arm: (23 commits)
  [ARM] Fix virtual to physical translation macro corner cases
  [ARM] update mach-types
  [ARM] 5421/1: ftrace: fix crash due to tracing of __naked functions
  MX1 fix include
  [ARM] 5419/1: ep93xx: fix build warnings about struct i2c_board_info
  [ARM] 5418/1: restore lr before leaving mcount
  ARM: OMAP: board-omap3beagle: set i2c-3 to 100kHz
  ARM: OMAP: Allow I2C bus driver to be compiled as a module
  ARM: OMAP: sched_clock() corrected
  ARM: OMAP: Fix compile error if pm.h is included
  [ARM] orion5x: pass dram mbus data to xor driver
  [ARM] S3C64XX: Fix s3c64xx_setrate_clksrc
  [ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/irq.c
  [ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/s3c6400-clock.c
  [ARM] S3C64XX: Fix USB host clock mux list
  [ARM] S3C64XX: Fix name of USB host clock.
  [ARM] S3C64XX: Rename IRQ_UHOST to IRQ_USBH
  [ARM] S3C64XX: Do gpiolib configuration earlier
  [ARM] S3C64XX: Staticise s3c64xx_init_irq_eint()
  [ARM] SMDK6410: Declare iodesc table static
  ...

The L0s workaround should be moved into a pci quirk and so it is not
necessary in the driver.  This update removes the L0s workaround from the
igb driver.

This was the second half of the PCI quirk patch that Matthew Wilcox did
not pick up when he picked up the quirk patch.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  Fix Xilinx SystemACE driver to handle empty CF slot
  block: fix memory leak in bio_clone()
  block: Add gfp_mask parameter to bio_integrity_clone()

The SystemACE driver does not handle an empty CF slot gracefully. An
empty CF slot ends up hanging the system. This patch adds a check for
the CF state and stops trying to process requests if the slot is empty.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

If bio_integrity_clone() fails, bio_clone() returns NULL without freeing
the newly allocated bio.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Stricter gfp_mask might be required for clone allocation.
For example, request-based dm may clone bio in interrupt context
so it has to use GFP_ATOMIC.
Signed-off-by: NKiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: NMartin K. Petersen <martin.petersen@oracle.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Mark Eins: Fix configuration.
  MIPS: Fix TIF_32BIT undefined problem when seccomp is disabled

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (31 commits)
  [SCSI] qla2xxx: Update version number to 8.03.00-k4.
  [SCSI] qla2xxx: Correct overwrite of pre-assigned init-control-block structure size.
  [SCSI] qla2xxx: Correct truncation in return-code status checking.
  [SCSI] qla2xxx: Correct vport delete bug.
  [SCSI] qla2xxx: Use correct value for max vport in LOOP topology.
  [SCSI] qla2xxx: Correct address range checking for option-rom updates.
  [SCSI] fcoe: Change fcoe receive thread nice value from 19 (lowest priority) to -20
  [SCSI] fcoe: fix handling of pending queue, prevent out of order frames (v3)
  [SCSI] fcoe: Out of order tx frames was causing several check condition SCSI status
  [SCSI] fcoe: fix kfree(skb)
  [SCSI] fcoe: ETH_P_8021Q is already in if_ether and fcoe is not using it anyway
  [SCSI] libfc: do not change the fh_rx_id of a recevied frame
  [SCSI] fcoe: Correct fcoe_transports initialization vs. registration
  [SCSI] fcoe: Use setup_timer() and mod_timer()
  [SCSI] libfc, fcoe: Remove unnecessary cast by removing inline wrapper
  [SCSI] libfc, fcoe: Cleanup function formatting and minor typos
  [SCSI] libfc, fcoe: Fix kerneldoc comments
  [SCSI] libfc: Cleanup libfc_function_template comments
  [SCSI] libfc: check for err when recv and state is incorrect
  [SCSI] libfc: rename rp to rdata in fc_disc_new_target()
  ...

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  ata_piix: add workaround for Samsung DB-P70
  libata: Keep shadow last_ctl up to date during resets
  sata_mv: fix MSI irq race condition

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  NFS: Fix the fix to Bugzilla #11061, when IPv6 isn't defined...
  SUNRPC: xprt_connect() don't abort the task if the transport isn't bound
  SUNRPC: Fix an Oops due to socket not set up yet...
  Bug 11061, NFS mounts dropped
  NFS: Handle -ESTALE error in access()
  NLM: Fix GRANT callback address comparison when IPv6 is enabled
  NLM: Shrink the IPv4-only version of nlm_cmp_addr()
  NFSv3: Fix posix ACL code
  NFS: Fix misparsing of nfsv4 fs_locations attribute (take 2)
  SUNRPC: Tighten up the task locking rules in __rpc_execute()

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
  ocfs2: Use xs->bucket to set xattr value outside
  ocfs2: Fix a bug found by sparse check.
  ocfs2: tweak to get the maximum inline data size with xattr
  ocfs2: reserve xattr block for new directory with inline data

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  V4L/DVB (10978): Report tuning algorith correctly
  V4L/DVB (10977): STB6100 init fix, the call to stb6100_set_bandwidth needs an argument
  V4L/DVB (10976): Bug fix: For legacy applications stv0899 performs search only first time after insmod.
  V4L/DVB (10975): Bug: Use signed types, Offsets and range can be negative
  V4L/DVB (10974): Use Diseqc 3/3 mode to send data
  V4L/DVB (10972): zl10353: i2c_gate_ctrl bug fix
  V4L/DVB (10834): zoran: auto-select bt866 for AverMedia 6 Eyes
  V4L/DVB (10832): tvaudio: Avoid breakage with tda9874a
  V4L/DVB (10789): m5602-s5k4aa: Split up the initial sensor probe in chunks.

* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6.29:
  parisc: update defconfigs
  parisc: define x->x mmio accessors
  parisc: dino: struct device - replace bus_id with dev_name(), dev_set_name()
  parisc: convert cpu_check_affinity to new cpumask api
  parisc: convert (read|write)bwlq to inlines
  parisc: fix use of new cpumask api in irq.c
  parisc: update parisc for new irq_desc
  parisc: update MAINTAINERS
  parisc: fix wrong assumption about bus->self
  parisc: fix 64bit build
  parisc: add braces around arguments in assembler macros
  parisc: fix dev_printk() compile warnings for accessing a device struct
  parisc: remove unused local out_putf label
  parisc: fix `struct pt_regs' declared inside parameter list warning
  parisc: fix section mismatch warnings
  parisc: remove klist iterators
  parisc: BUG_ON() cleanup

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: save the returned value of dma_map_sg
  ide-floppy: do not map dataless cmds to an sg

pgmoved should be cleared after updating recent_rotated.
Signed-off-by: NDaisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Rik van Riel <riel@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Acked-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

eCryptfs has file encryption keys (FEK), file encryption key encryption
keys (FEKEK), and filename encryption keys (FNEK).  The per-file FEK is
encrypted with one or more FEKEKs and stored in the header of the
encrypted file.  I noticed that the FEK is also being encrypted by the
FNEK.  This is a problem if a user wants to use a different FNEK than
their FEKEK, as their file contents will still be accessible with the
FNEK.

This is a minimalistic patch which prevents the FNEKs signatures from
being copied to the inode signatures list.  Ultimately, it keeps the FEK
from being encrypted with a FNEK.
Signed-off-by: NTyler Hicks <tyhicks@linux.vnet.ibm.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Acked-by: NDustin Kirkland <kirkland@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When a ramfs nommu mapping is expanded, contiguous pages are allocated
and added to the pagecache.  The caller's reference is then passed on
by moving whole pagevecs to the file lru list.

If the page cache adding fails, make sure that the error path also
moves the pagevec contents which might still contain up to PAGEVEC_SIZE
successfully added pages, of which we would leak references otherwise.
Signed-off-by: NJohannes Weiner <hannes@cmpxchg.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Enrik Berkhan <Enrik.Berkhan@ge.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The pages attached to a ramfs inode's pagecache by truncation from nothing
- as done by SYSV SHM for example - may get discarded under memory
pressure.

The problem is that the pages are not marked dirty.  Anything that creates
data in an MMU-based ramfs will cause the pages holding that data will
cause the set_page_dirty() aop to be called.

For the NOMMU-based mmap, set_page_dirty() may be called by write(), but
it won't be called by page-writing faults on writable mmaps, and it isn't
called by ramfs_nommu_expand_for_mapping() when a file is being truncated
from nothing to allocate a contiguous run.

The solution is to mark the pages dirty at the point of allocation by the
truncation code.
Signed-off-by: NEnrik Berkhan <Enrik.Berkhan@ge.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>