PTP hardware filter configuration performed by the driver for a given
user requested config is not correct for some of the PTP modes.
Following changes are needed for PTP config-filter implementation.
 1. NIG_REG_TX_PTP_EN register - Bits 0/1/2 respectively enables
    TimeSync/"V1 frame format support"/"V2 frame format support" on
    the TX side. Set the associated bits based on the user request.
 2. ptp4l application fails to operate in Peer Delay mode. Following
    changes are needed to fix this,
    a. Driver should enable (set to 0) DA #1-related bits for IPv4,
       IPv6 and MAC destination addresses in these registers:
         NIG_REG_TX_LLH_PTP_RULE_MASK
         NIG_REG_LLH_PTP_RULE_MASK
    b. NIG_REG_LLH_PTP_PARAM_MASK/NIG_REG_TX_LLH_PTP_PARAM_MASK should
       be set to 0x0 in all modes.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct timespec is not y2038 safe.
Audit timestamps are recorded in string format into
an audit buffer for a given context.
These mark the entry timestamps for the syscalls.
Use y2038 safe struct timespec64 to represent the times.
The log strings can handle this transition as strings can
hold upto 1024 characters.
Signed-off-by: NDeepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NPaul Moore <paul@paul-moore.com>
Acked-by: NRichard Guy Briggs <rgb@redhat.com>
Signed-off-by: NPaul Moore <paul@paul-moore.com>

We were setting the portid incorrectly in the netlink message headers,
fix that to always be 0 (nlmsg_pid = 0).
Signed-off-by: NPaul Moore <paul@paul-moore.com>
Reviewed-by: NRichard Guy Briggs <rgb@redhat.com>

This untangles the DM_MAPIO_* values returned from ->clone_and_map_rq
from the error codes used by the block layer.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

Instead of returning either a DM_ENDIO_* constant or an error code, add
a new DM_ENDIO_DONE value that means keep errno as is.  This allows us
to easily keep the existing error code in case where we can't push back,
and it also preparares for the new block level status codes with strict
type checking.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

By using smaller datatypes this (rather large) struct shrinks considerably
(80 -> 48 bytes on x86_64).

As this is embedded in other structs, this also rerduces size of several
others, e.g. cls_fl_head or nft_hash.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Output to the RDMA driver whether DPM mode is enabled or disabled in
the HW and if so what is the number of WIDs it supports
Signed-off-by: NRam Amrani <Ram.Amrani@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers usually have a number of restrictions for running XDP
- most common being buffer sizes, LRO and number of rings.
Even though some drivers try to be helpful and print error
messages experience shows that users don't often consult
kernel logs on netlink errors.  Try to use the new extended
ack mechanism to carry the message back to user space.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As we propagate extended ack reporting throughout various paths in
the kernel it may be that the same function is called with the
extended ack parameter passed as NULL.  One place where that happens
is in drivers which have a centralized reconfiguration function
called both from ndos and from ethtool_ops.  Add a new helper for
setting the error message in such conditions.

Existing helper is left as is to encourage propagating the ext act
fully wherever possible.  It also makes it clear in the code which
messages may be lost due to ext ack being NULL.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The x86 conversion to the generic GUP code included a small change which causes
crashes and data corruption in the pmem code - not good.

The root cause is that the /dev/pmem driver code implicitly relies on the x86
get_user_pages() implementation doing a get_page() on the page refcount, because
get_page() does a get_zone_device_page() which properly refcounts pmem's separate
page struct arrays that are not present in the regular page struct structures.
(The pmem driver does this because it can cover huge memory areas.)

But the x86 conversion to the generic GUP code changed the get_page() to
page_cache_get_speculative() which is faster but doesn't do the
get_zone_device_page() call the pmem code relies on.

One way to solve the regression would be to change the generic GUP code to use
get_page(), but that would slow things down a bit and punish other generic-GUP
using architectures for an x86-ism they did not care about. (Arguably the pmem
driver was probably not working reliably for them: but nvdimm is an Intel
feature, so non-x86 exposure is probably still limited.)

So restructure the pmem code's interface with the MM instead: get rid of the
get/put_zone_device_page() distinction, integrate put_zone_device_page() into
__put_page() and and restructure the pmem completion-wait and teardown machinery:

Kirill points out that the calls to {get,put}_dev_pagemap() can be
removed from the mm fast path if we take a single get_dev_pagemap()
reference to signify that the page is alive and use the final put of the
page to drop that reference.

This does require some care to make sure that any waits for the
percpu_ref to drop to zero occur *after* devm_memremap_page_release(),
since it now maintains its own elevated reference.

This speeds up things while also making the pmem refcounting more robust going
forward.
Suggested-by: NKirill Shutemov <kirill.shutemov@linux.intel.com>
Tested-by: NKirill Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Reviewed-by: NLogan Gunthorpe <logang@deltatee.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/149339998297.24933.1129582806028305912.stgit@dwillia2-desk3.amr.corp.intel.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

When IP tunnel encapsulation rules are offloaded, the kernel can't see
the traffic of the offloaded flow. The neighbour for the IP tunnel
destination of the offloaded flow can mistakenly become STALE and
deleted by the kernel since its 'used' value wasn't changed.

To make sure that a neighbour which is used by the HW won't become
STALE, we proactively update the neighbour 'used' value every
DELAY_PROBE_TIME period, when packets were matched and counted by the HW
for one of the tunnel encap flows related to this neighbour.

The periodic task that updates the used neighbours is scheduled when a
tunnel encap rule is successfully offloaded into HW and keeps re-scheduling
itself as long as the representor's neighbours list isn't empty.

Add, remove, lookup and status change operations done over the
representor's neighbours list or the neighbour hash entry encaps list
are all serialized by RTNL lock.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

This was already disabled a while ago because it caused I/O errors,
and it's severly getting into the way of the discard / write zeroes
rework.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

The only difference between ->run_work and ->delay_work, is that
the latter is used to defer running a queue. This is done by
marking the queue stopped, and scheduling ->delay_work to run
sometime in the future. While the queue is stopped, direct runs
or runs through ->run_work will not run the queue.

If we combine the handlers, then we need to handle two things:

1) If a delayed/stopped run is scheduled, then we should not run
   the queue before that has been completed.
2) If a queue is delayed/stopped, the handler needs to restart
   the queue. Normally a run of a queue with the stopped bit set
   would be a no-op.

Case 1 is handled by modifying a currently pending queue run
to the deadline set by the caller of blk_mq_delay_queue().
Subsequent attempts to queue a queue run will find the work
item already pending, and direct runs will see a stopped queue
as before.

Case 2 is handled by adding a new bit, BLK_MQ_S_START_ON_RUN,
that tells the work handler that it should clear a stopped
queue and run the handler.
Reviewed-by: NBart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

This modifies (or adds, if not currently pending) an existing
delayed work item.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

They serve the exact same purpose. Get rid of the non-delayed
work variant, and just run it without delay for the normal case.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBart Van Assche <Bart.VanAssche@sandisk.com>
Reviewed-by: NMing Lei <ming.lei@redhat.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

Parse the BSS max idle period element and set the BSS configuration
accordingly so the driver can use this information to configure the
max idle period and to use protected management frames for keep alive
when required.

The BSS max idle period element is defined in IEEE802.11-2016,
section 9.4.2.79
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Introduce an enumeration type for the queue mode.  This patch does
not change any functionality but makes the DM code easier to read.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

Support for l2 multicast flood control was added in commit b6cb5ac8
("net: bridge: add per-port multicast flood flag"). It allows broadcast
as it was introduced specifically for unknown multicast flood control.
But as broadcast is a special case of multicast, this may also need to
be disabled. For this purpose, introduce a flag to disable the flooding
of received l2 broadcasts. This approach is backwards compatible and
provides flexibility in filtering for the desired packet types.

Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NMike Manning <mmanning@brocade.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the comment for netif_dormant() function to reflect
the intended usage.
Signed-off-by: NZhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When max_size is not set or if it set to a sufficiently large
value, the nelems counter can overflow.  This would cause havoc
with the automatic shrinking as it would then attempt to fit a
huge number of entries into a tiny hash table.

This patch fixes this by adding max_elems to struct rhashtable
to cap the number of elements.  This is set to 2^31 as nelems is
not a precise count.  This is sufficiently smaller than UINT_MAX
that it should be safe.

When max_size is set max_elems will be lowered to at most twice
max_size as is the status quo.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

AXP803 is a new PMIC chip produced by X-Powers, usually paired with A64
via RSB bus. The PMIC itself is like AXP288, but with RSB support and
dedicated VBUS and ACIN.

Add support for it in the axp20x mfd driver.

Currently only power key function is supported.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Pad retention should be controlled from pin control driver, so remove it
from Exynos LPASS driver. After this change, no more access to PMU regmap
is needed, so remove also the code for handling PMU regmap.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NKrzysztof Kozlowski <krzk@kernel.org>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: NRob Herring <robh@kernel.org>
Acked-for-MFD-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

MFD support for DA9061 is provided as part of the DA9062 device driver.

The registers header file adds two new chip variant IDs defined in DA9061
and DA9062 hardware. The core header file adds new software enumerations
for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
for distinguishing between DA9061/62 devices in software.

The core source code adds a new .compatible of_device_id entry. This is
extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
.data entry now holds a reference to the enumerated device type.

A new regmap_irq_chip model is added for DA9061 and this supports the new
list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
new sub system components for DA9061. Support is added for a new DA9061
regmap_config which lists the correct readable, writable and volatile
ranges for this chip.

The probe function uses the device tree compatible string to switch on the
da9062_compatible_types and configure the correct mfd cells, irq chip and
regmap config.

Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
Signed-off-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

All macros prefixed with AT91[SAM9]_SMC have been replaced by equivalent
definitions prefixed with ATMEL_SMC, and the at91sam9_smc_xxxx() helpers
are no longer used.
Drop these definitions before someone starts using them again.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

These new helpers + macro definitions are meant to replace the old ones
which are unpractical to use.

Note that the macros and function prefixes have been intentionally
changed to ATMEL_[H]SMC_XX and atmel_[h]smc_ to reflect the fact that
this IP is also embedded in avr32 SoCs (and not only in at91 ones).
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

For better understanding of relationship between headers and modules
rename:
	intel_bxtwc.h -> intel_soc_pmic_bxtwc.h

While here, remove file name from the file itself.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

There is no need to include intel_soc_pmic.h into header which doesn't
require it.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The registers 0x56 and 0x57 of AXP22X PMIC store the value of the
internal temperature of the PMIC.

This patch modifies the name of these registers from AXP22X_PMIC_ADC_H/L
to AXP22X_PMIC_TEMP_H/L so their purpose is clearer.
Signed-off-by: NQuentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

TI LMU (Lighting Management Unit) driver supports lighting devices below.

  LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.

LMU devices have common features.
  - I2C interface for accessing device registers
  - Hardware enable pin control
  - Backlight brightness control
  - Notifier for hardware fault monitoring
  - Regulators for LCD display bias

It contains fault monitor, backlight, LED and regulator driver.

LMU fault monitor
-----------------
  LM3633 and LM3697 provide hardware monitoring feature.
  It enables open or short circuit detection.
  After monitoring is done, each device should be re-initialized.
  Notifier is used for this case.
  Separate patch for 'ti-lmu-fault-monitor' will be sent later.

Backlight
---------
  It's handled by TI LMU backlight consolidated driver and
  chip dependent data. Separate patchset will be sent later.

LED indicator
-------------
  LM3633 has 6 indicator LEDs. Programmable dimming pattern is also
  supported. Separate patch for 'leds-lm3633' will be sent later.

Regulator
---------
  LM3631 has 5 regulators for the display bias.
  LM3632 supports 3 regulators. One consolidated driver enables it.
  The lm363x regulator driver is already upstreamed.
Signed-off-by: NMilo Kim <milo.kim@ti.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch installs an ACPI GPE handler for LID0 ACPI device to indicate
ACPI core that this GPE should stay enabled for lid to work in suspend
to idle path.
Signed-off-by: NArchana Patni <archana.patni@intel.com>
Signed-off-by: NThierry Escande <thierry.escande@collabora.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Some of the enum definitions are unnamed but there's still
an attempt at documenting them - that doesn't work. Name
them to make that work.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add the definition for FT-8021.1X AKM selector as defined in
IEEE Std 802.11-2016, table 9-133.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add the definitions for SUITE_B and SUITE_B_192 AKM selectors as
defined in IEEE802.11REVmc_D5.0, table 9-132.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This new callback function will be used in the next patch to show
more information about SCSI requests.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NOmar Sandoval <osandov@fb.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

Some devices or distributions use HZ=100 or HZ=250

TCP receive buffer autotuning has poor behavior caused by this choice.
Since autotuning happens after 4 ms or 10 ms, short distance flows
get their receive buffer tuned to a very high value, but after an initial
period where it was frozen to (too small) initial value.

With tp->tcp_mstamp introduction, we can switch to high resolution
timestamps almost for free (at the expense of 8 additional bytes per
TCP structure)

Note that some TCP stacks use usec TCP timestamps where this
patch makes even more sense : Many TCP flows have < 500 usec RTT.
Hopefully this finer TS option can be standardized soon.

Tested:
 HZ=100 kernel
 ./netperf -H lpaa24 -t TCP_RR -l 1000 -- -r 10000,10000 &

 Peer without patch :
 lpaa24:~# ss -tmi dst lpaa23
 ...
 skmem:(r0,rb8388608,...)
 rcv_rtt:10 rcv_space:3210000 minrtt:0.017

 Peer with the patch :
 lpaa23:~# ss -tmi dst lpaa24
 ...
 skmem:(r0,rb428800,...)
 rcv_rtt:0.069 rcv_space:30000 minrtt:0.017

We can see saner RCVBUF, and more precise rcv_rtt information.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We want to use precise timestamps in TCP stack, but we do not
want to call possibly expensive kernel time services too often.

tp->tcp_mstamp is guaranteed to be updated once per incoming packet.

We will use it in the following patches, removing specific
skb_mstamp_get() calls, and removing ack_time from
struct tcp_sacktag_state.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

no users in the tree, insecure_max_entries is always set to
ht->p.max_size * 2 in rhtashtable_init().

Replace only spot that uses it with a ht->p.max_size check.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Ethernet link on an interrupt driven PHY was not coming up if the Ethernet
cable was plugged before the Ethernet interface was brought up.

The patch trigger PHY state machine to update link state if PHY was requested to
do auto-negotiation and auto-negotiation complete flag already set.

During power-up cycle the PHY do auto-negotiation, generate interrupt and set
auto-negotiation complete flag. Interrupt is handled by PHY state machine but
doesn't update link state because PHY is in PHY_READY state. After some time
MAC bring up, start and request PHY to do auto-negotiation. If there are no new
settings to advertise genphy_config_aneg() doesn't start PHY auto-negotiation.
PHY continue to stay in auto-negotiation complete state and doesn't fire
interrupt. At the same time PHY state machine expect that PHY started
auto-negotiation and is waiting for interrupt from PHY and it won't get it.

Fixes: 321beec5 ("net: phy: Use interrupts when available in NOLINK state")
Signed-off-by: NAlexander Kochetkov <al.kochet@gmail.com>
Cc: stable <stable@vger.kernel.org> # v4.9+
Tested-by: NRoger Quadros <rogerq@ti.com>
Tested-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

all architectures converted
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Similar to ip_register_table, pass nf_hook_ops to ebt_register_table().
This allows to handle hook registration also via pernet_ops and allows
us to avoid use of legacy register_hook api.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>