Make the indentation of the source code consistent. Detected by
smatch.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When FM is disabled, and the HFI port on the switch is
changed from MgmtAllowed=YES to MgmtAllowed=NO and the
link is bounced, FULL_MGMT_P_KEY doesn't get cleared
from the pkey table. This also occurs when the QSFP
cable is moved from a switch port with MgmtAllowed=YES
to a MgmtAllowed=NO port. Clear pkey entry properly.

Also, when the driver is loaded and the switch port is
set to MgmtAllowed=NO, FULL_MGMT_P_KEY shouldn't be added
to pkey table after FM is started. Only set FULL_MGMT_P_KEY
in the pkey table if switch port is configured to
MgmtAllowed=YES.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The TODO list for the hfi1 driver was completed during 4.6. In addition
other objections raised (which are far beyond what was in the TODO list)
have been addressed as well. It is now time to remove the driver from
staging and into the drivers/infiniband sub-tree.
Reviewed-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove "IB" keyword from log messages.
Correct comment for thermal sensor init function.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NJakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The RESET_N bit of the ASIC_QSFPn_OE register is not used by
the hardware.  Remove code that tries to use it - it does
nothing.
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The function level reset in init_chip() and subsequent write of all 1s
to the ASIC_QSFP registers effectively resets attached active and
optical QSFP modules that pay attention to the RESET_N pin.

We subsequently try to access the QSFP management interface to qualify
and tune the channel and fabric SerDes before enough time (2 seconds
per SFF 8679 spec for QSFP28 modules) has elapsed for the module to
finish initialization. This fails and causes the failure of the channel
tuning algorithm, preventing us from bringing the link up.

This patch checks the port type prior to beginning channel and SerDes
tuning, and if found to be QSFP, watches for the QSFP initialization
complete interrupt, with a maximum timeout of 2 seconds, to allow the
initialization to complete.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

QSFP modules can raise an interrupt to inform us of expected conditions
while the link is down, such as RX power low. Actively ignore these
conditions when the link is down as they only add reporting noise.
Continue reporting conditions that are valid at all times, such as
temperature alarms and warnings.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The code to save the link down reason for reporting to the SMA
was in a location before the actual reason was read.  Move the
SMA link down reason assignment to a better location.
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The 8051 uses a link down reason to inform the driver why the
link went down.  The neighbor planned link down reason code is
only valid when a link down idle message is received by the 8051.
Enhance the explanation on why the link went down.
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Versions of the 8051 firmware < 0.38 may report a link failure
as a link downgrade with a width of 0 followed by a link down
notification.  Ignore the zero width downgrade notification -
the driver should follow the link down path.
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add a receive side mapping rule to extract expected user packets with
the FECN bit set and place them in an eager buffer.  This will allow
user libraries to recognize that a FECN was sent when using header
suppression and respond appropriately.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Move the rule setting code into its own routine for improved
searchability and reuse.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The decision to use QOS affects other resource allocation.
Move the QOS decision logic into its own function so it can
be called by other interested parties.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Refactor the allocation, tracking, and writing of the RSM map table
into its own set of routines.  This will allow the map table to be
passed to multiple users to fill in as needed.  Start with the original
user, QOS.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The pio buffers were pooled evenly among all kernel contexts and
user contexts. However, the demand from kernel contexts is much
lower than user contexts. This patch reduces the allocation for
kernel contexts and thus makes more credits available for PSM,
helping performance. This is especially useful on high core-count
systems where large numbers of contexts are used.

A new context type SC_VL15 is added to distinguish the context used
for VL15 from other kernel contexts. The reason is that VL15 needs
to support 2KB sized packet while other kernel contexts need only
support packets up to the size determined by "piothreshold", which
has a default value of 256.

The new allocation method allows triple buffering of largest pio
packets configured for these contexts. This is sufficient to maintain
verbs performance. The largest pio packet size is 2048B for VL15
and "piothreshold" for other kernel contexts. A cap is applied to
"piothreshold" to avoid excessive buffer allocation.

The special case that SDMA is disable is handled differently. In
that case, the original pooling allocation is used to better
support the much higher pio traffic.

Notice that if adaptive pio is disabled (piothreshold==0), the pio
buffer size doesn't matter for non-VL15 kernel send contexts when
SDMA is enabled because pio is not used at all on these contexts
and thus the new allocation is still valid. If SDMA is disabled then
pooling allocation is used as mentioned in previous paragraph.

Adjustment is also made to the calculation of the credit return
threshold for the kernel contexts. Instead of purely based on
the MTU size, a percentage based threshold is also considered and
the smaller one of the two is chosen. This is necessary to ensure
that with the reduced buffer allocation credits are returned in
time to avoid unnecessary stall in the send path.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: NDean Luick <dean.luick@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NMark Debbage <mark.debbage@intel.com>
Reviewed-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NJianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Change the default number of user contexts to the number of real
(non-HT) cpu cores in order to reduce the division of hfi1 hardware
contexts in the case of high core counts with hyper-threading enabled.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The pre-LNI SerDes and channel tuning algorithm already checks for
module presence assertion for the relevant port types. The extraneous
check removed in this patch blocks link up for port types for which
the module presence assertion is not relevant.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Clock and data recovery mechanisms (CDRs) in active QSFP modules
can be turned on or off to improve the bit error rate observed on
the channel. Signal integrity and bit error rate requirements require
us to always turn on any CDRs present in low power cables (power
dissipation 2.5W or lower). However, we adhere to the platform
designer's settings (provided in the platform configuration) for
higher power cables (dissipation 3.5W or higher) if the platform
designer has determined that the platform requires the CDRs to be
turned on (or off) and is capable of supplying and cooling the higher
power modules.

This patch also introduces the get_qsfp_power_class function to
centralize the bit twiddling required to determine the QSFP power class
across the code. Reusing this function improves the readability of code
that depends on knowing the power class of the cable, such as the
active and optical channel tuning algorithm.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add the P_KEY check for user-context mechanism for
both PIO and SDMA. For PIO, the
SendCtxtCheckEnable.DisallowKDETHPackets is set by
default. When the P_KEY is set,
SendCtxtCheckEnable.DisallowKDETHPackets is cleared.
For SDMA, a software check was included. This change
requires user processes to set the P_KEY before sending
any packets, otherwise, the sent packet will fail. The
original submission didn't have this check but it's
required.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NMikto Haralanov <mitko.haralanov@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Make init_qpmap_table() easier to understand by simplifying
the loop indexing and writing each register when it is "full",
removing the need for a follow-on register write.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The QOS RSM rule mappings are off by one, referencing a kernel receive
context that does not exist.

Correctly start the QOS RSM map entries at FIRST_KERNEL_CONTEXT rather
than MIN_KERNEL_KCTXTS.  Remove the cruft that hid this.

Change the QP map table so all traffic not caught by QOS RSM goes to
the control context rather than the first QOS context.

Correct comments to match the actual code operation and intent.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove an invalid compare of the number of QOS RSM map table entries
against the number of physical receive contexts.  The RSM map table
has its own size and has no relation to the number of physical receive
contexts.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The bit width for num_vls, n, needs to be calculated based on
the pow2 rounded up of the number of vls.  Otherwise num_vls of 3,
5, 6, and 7 will have misplaced QOS RSM map entries.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Host handshake timeout can occur during the verify capability
state. This is a LNI related failure and should be
handled in the same way as other LNI failures.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The flag HFI1_DO_INIT_ASIC flag is no longer used.  Remove
the flag and the code that sets it.
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Use the resource reservation system to flag that the ASIC
thermal has been initialized.
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove the mutex guarding each operation in favor the ASIC
resource acquire/release.  Push the resource acquire/release,
above each operation call to allow exclusive access across
multiple operations.
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The SBus resource includes SBUS, PCIE, and THERM registers.
Change SBus handling to use the new ASIC resource reservation system.
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The ASIC block is a shared hardware resource between two devices
on the chip.  Add functions to acquire and release these resources
in a way that is safe for both multiple users on the same OS
and multiple users on different OSes, while holding the hardware
mutex as little as possible.

Reservations are noted in a scratch register in the shared region.
There are two types of reservations: per-HFI dynamic and permanent.
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Create a shared structure to exist between devices that share the
same ASIC.
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The ASIC block is shared between two HFIs. Individual devices
should not initialize registers there. Retain the power-on values.
Individual users set registers as needed with one exception.
Clear sbus fast mode on "slow" calls.
Reviewed-by: NMitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Implement changes recommended by the Coccinelle tool to move constant to
the right in bitwise operations

-bash-4.2$ make coccicheck MODE=report M=drivers/infiniband/hw/hfi1/

drivers/infiniband/hw/hfi1/pio.c:765:4-16: Move constant to right.
drivers/infiniband/hw/hfi1/rc.c:2503:19-29: Move constant to right.
drivers/infiniband/hw/hfi1/chip.c:9813:11-22: Move constant to right.
drivers/infiniband/hw/hfi1/chip.c:14468:29-40: Move constant to right.
Reviewed-by: NJubin John <jubin.john@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NHarish Chegondi <harish.chegondi@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This patch removes unnecessary return variables and compresses the
return logic.

The coccinelle script that finds and fixes this issue is:

@@ type T; identifier i,f; constant C; @@
- T i;
...when != i
when strict
( return -C;
|
- i =
+ return
f(...);
- return i;
)
Signed-off-by: NBhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch tests the interrupt registers when the driver has no access to
its upstream component. In this case, it is highly likely that it is
running in a virtual machine (eg, Qemu-kvm guest). If the interrupt
registers are not mapped properly by the virtual machine monitor, an
error message will be printed and the probing will be terminated. This
will help the user identify the issue. On the other hand, if the driver
is running in a host or has access to its upstream component in some
other VM, it will do nothing.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NKaike Wan <kaike.wan@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

A cp or cat of /sys/kernel/debug/hfi1/hfi1_0/port1counters
produces the following message:

hfi1 0000:81:00.0: hfi1_0: index not supported
hfi1 0000:81:00.0: hfi1_0: read_cntrs does not support indexing

Fix by removing the file position logic and the associated messages
and make the file positioning the responsibility of the caller.

The port counter read function argument is changed to the per port
data structure since the counters are relative to the port and not
the device.
Reviewed-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This is a set of minor fixes including comment and log message cleanups
and improvements to the PHY layer code.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Count only the errors that apply to xmit discards.  Update
the comment to better explain the limitations of the count.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Fix the header by moving the copyright notice out of the license text
and to the top of the header. Also, update the copyright date.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add braces on all arms of statements to fix checkpatch check:
CHECK: braces {} should be used on all arms of this statement
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Fix code alignment to fix checkpatch check:
CHECK: Alignment should match open parenthesis
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>