Remove the open coded access to irq_desc which will fail on sparse irq
and use the proper wrappers.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Add new/changed base address definitions and resources for
OMAP3630 ISP.

The OMAP3430 CSI2PHY block is same as the OMAP3630 CSIPHY2
block. But the later name is chosen as it gives more symmetry
to the names.
Signed-off-by: NTuukka Toivonen <tuukkat76@gmail.com>
Signed-off-by: NVimarsh Zutshi <vimarsh.zutshi@gmail.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Commit db97eb7d
(omap: gpmc: enable irq mode in gpmc) enabled interrupts for
GPMC (General Purpose Memory Controller). However, looks like
this patch only works on omap3. Fix the issues to avoid warnings
on omap4 during the boot.

GPMC: number of chip select is 8, CS0 to CS7. One less IRQ
allocated throws below warning at boot:

[    0.429290] Trying to install type control for IRQ409
[    0.429290] Trying to set irq flags for IRQ409

Resolve following warning messages in boot when irq chip is not set:

[    0.429229] Trying to install interrupt handler for IRQ402
[    0.429229] Trying to install interrupt handler for IRQ403
[    0.429229] Trying to install interrupt handler for IRQ404
[    0.429260] Trying to install interrupt handler for IRQ405
[    0.429260] Trying to install interrupt handler for IRQ406
[    0.429260] Trying to install interrupt handler for IRQ407
[    0.429290] Trying to install interrupt handler for IRQ408

Resolve following warning in OMAP4:
[    0.429290] gpmc: irq-20 could not claim: err -22
Signed-off-by: NBalaji T K <balajitk@ti.com>
[tony@atomide.com: combined patches into one, updated comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adding display type HDMI in dss_features, overlay and the manager so that
HDMI type of display will be recognized.
Signed-off-by: NMythri P K <mythripk@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

request_mem_region() error exit will leak ioremapped memory. Fix this
by moving the ioremap() after request_mem_region(), which is the proper
order to do this anyway.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Currently IOVMM driver sets IOVMF_DA_FIXED/IOVMF_DA_ANON flags according
to input 'da' address when mapping memory:
da == 0: IOVMF_DA_ANON
da != 0: IOVMF_DA_FIXED

It prevents IOMMU to map first page with fixed 'da'. To avoid such
issue, IOVMM will not automatically set IOVMF_DA_FIXED. It should now
come from the user throught 'flags' parameter when mapping memory.
As IOVMF_DA_ANON and IOVMF_DA_FIXED are mutually exclusive, IOVMF_DA_ANON
can be removed. The driver will now check internally if IOVMF_DA_FIXED
is set or not.
Signed-off-by: NDavid Cohen <dacohen@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

commit c7f4ab26 allowed mapping the NULL
address if da_start==0, which would then not get unmapped. Disallow
this again if IOVMF_DA_ANON is set. And spell variable 'alignment'
correctly.
Signed-off-by: NMichael Jones <michael.jones@matrix-vision.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This avoids going through the list unnecessarily when
idling devices for runtime PM.

Based on an earlier patch by sricharan <r.sricharan@ti.com>.
Signed-off-by: Nsricharan <r.sricharan@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

New variable skip_initial_unlocking is added to the omap_onenand_platform_data.
This is used to inform the onenand driver to skip onenand unlocking when it
is initialized.
Signed-off-by: NRoman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Introduce functions which request and release VC's. This will be used in panel
drivers in their probes.

omap_dsi_request_vc() takes in the pointer to the omap_dss_device, the VC_ID
parameter which goes into the header of the DSI packets, and returns a Virtual
channel number (or virtual channel register set) which it can use.

omap_dsi_set_vc_id() takes the omap_dss_device pointer, the Virtual Channel
number and the VC_ID that needs to be set for the specifed Virtual Channel.

omap_dsi_release_vc() takes the omap_dss_device pointer and the Virtual Channel
number that needs to be made free.

Initialisation of VC parameters is done in dsi_init().
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSI PLL output clock names have been made more generic. The clock name
describes what the source of the clock and what clock is used for. Some of
DSI PLL parameters like dividers and DSI PLL source have also been made more
generic.

dsi1_pll_fclk and dsi2_pll_fclk have been changed as dsi_pll_hsdiv_dispc_clk
and dsi_pll_hsdiv_dsi_clk respectively. Also, the hsdividers are now named
regm_dispc and regm_dsi instead of regm3 and regm4.

Functions and macros named on the basis of these clock names have also been
made generic.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Provide a function in pdata to allow dss submodules to check if a given
clock is available on a platform as an optional clock.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
(based on implementation from Senthil)
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Looks up the hwmod database for each of the given DSS HW IP and builds
omap_device which inturn does the platform device register for each of DSS HW IP
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This saves some power. OMAP4 version should check for GPT module ID, as
autoidle is only supported on a subset of these.
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Create a new API that forms a wrapper to _set_module_autoidle()
to modify the AUTOIDLE bit.

This API is intended to be used by drivers that requires direct
manipulation of the AUTOIDLE bits in SYSCONFIG register.
McBSP driver requires autoidle bit to be enabled/disabled while
using sidetone feature.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: restrict the hwmod states that the autoidle bit can be changed
 in; changed function name; dropped "int" from "unsigned int long"]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Some boards can't tolerate IP blocks being reset when they are initialized.
Michael Büsch cites a case with the Nokia N810:

    http://www.spinics.net/lists/linux-omap/msg47277.html

To allow such boards to continue working normally, allow board file
maintainers to mark IP blocks to prevent them from being reset upon
init.  This is done via a hwmod function, omap_hwmod_no_setup_reset().
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Michael Buesch <mb@bu3sch.de>

On OMAP2 and OMAP3 the reset ctrl shift doesn't match the
status bit, as it does on OMAP4, when handling the reset lines.

This patch adds a new member in the reset info structure, so now it
can be added as part of hwmod data, and checked accordingly for
OMAP2 or 3; otherwise, there could be cases when the shift masks
doesn't match both of the registers, and a successful reset might
throw an error message or vice versa.
Signed-off-by: NOmar Ramirez Luna <omar.ramirez@ti.com>
[paul@pwsan.com: added a warning if st_shift used on OMAP4; renamed 'r'
 variable; improved some documentation]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The documented name of the HWMOD_NO_OCP_AUTOIDLE flag was incorrect; fix it.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Now that omap_hwmod + omap_device is used for OMAP UART device and
driver code, we no longer need the UART physical addresses in
omap_globals.

Note that the #defines for the base addresses are still left in
<plat/serial.h> since they are used by DEBUG_LL and uncompress code.

Build tested for OMAP1 (omap1_defconfig) and OMAP2+ (omap2plus_defconfig)
Signed-off-by: NKevin Hilman <khilman@ti.com>

Add the address spaces, irqs of the l3 interconnect to the
hwmod data. The hwmod changes are aligned with Benoit Cousson.
Signed-off-by: Nsricharan <r.sricharan@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NBenoit Cousson <b-cousson@ti.com>

Remove the DPLL rate tolerance code that is called during rate
rounding.  As far as I know, this code is never used, since it's been
more important for callers of the DPLL round_rate()/set_rate()
functions to obtain an exact rate than it is to save a relatively
small amount of power.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Bail out before we take the clockfw_lock spinlock if the corresponding
OMAP1 or OMAP2+ clock function is not defined.  The intention is to
reduce and simplify the work that is done inside the spinlock.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

At this point in time, there's no reason for this header file to be in
plat-omap/include/plat/voltage.h.  It should not be included by device
drivers, and the code that uses it is currently all under mach-omap2/.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

There's no reason for this header file to be in
plat-omap/include/plat/smartreflex.h.  The hardware devices are in
OMAP2+ SoCs only.  Leaving this header file in plat-omap causes
problems due to cross-dependencies with other header files that should
live in mach-omap2/.

Thanks to Benoît Cousson <b-cousson@ti.com> for suggesting the removal
of the smartreflex.h include from the OMAP3xxx hwmod data.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

WARNING: arch/arm/plat-omap/built-in.o(.data+0x6d4): Section mismatch in reference from the variable omap_driver to the function .init.text:omap_cpu_init()
The variable omap_driver references
the function __init omap_cpu_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The _add_optional_clock_alias function expects an entry
already existing in the clkdev table in the form of
<dev-id=NULL, con-id=role> which might not be the case
always.

Instead, just check if an entry already exists in clkdev
in the <dev-id=dev_name, con-id=role> form, else go ahead
and add one.

Remove any assumption of an entry already existing in clkdev
table in any form.

Since this means, adding a new entry in clkdev if it does
not already exist, and not really adding an 'alias',
also rename the function name
(s/_add_optional_clock_alias/_add_optional_clock_clkdev)
to reflect this.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Reported-by: NSumit Semwal <sumit.semwal@ti.com>
Cc: Sumit Semwal <sumit.semwal@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Partha Basak <p-basak2@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

OMAP2420 platform consists of mmc block as in omap1 and not the
hsmmc block as present in omap2430, omap3, omap4 platforms.
Removing all base address macro defines except keeping one for OMAP2420 and
adapting only hsmmc device registration and driver to hwmod framework.

Changes involves:
1) Remove controller reset in devices.c which is taken care of
   by hwmod framework.
2) Using omap-device layer to register device and utilizing data from
   hwmod data file for base address, dma channel number, Irq_number,
   device attribute.
3) Update the driver to use dev_attr to find whether controller
   supports dual volt cards
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Reviewed-by: NBalaji T K <balajitk@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add a device attribute to hwmod data of omap2430, omap3, omap4.
Currently the device attribute holds information regarding dual volt MMC card
support by the controller which will be later passed to the host driver via
platform data.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The MMC controller on the OMAP2420 is different from those
on the OMAP2430, OMAP3 and OMAP4 families - all of the latter
are identical. The one on the OMAP2420 is closer to that
on OMAP1 chips.

Currently, the n8x0 is the only OMAP2420 platform supported
in mainline which registers the MMC controller. Upcoming
changes to register the controllers using hwmod data are
potentially invasive. To reduce the risk, separate out the
2420 controller registration from the common init function
and update its only user. Also seperating out mux settings
for OMAP2420.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The prototype and defination of functions usb_ehci_init and
usb_ohci_init are removed. The ehci and ohci devices are
removed since usbhs device contains both ehci and ohci details.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

A new usbhs platform device is defined;
this device will be the parent device of ehci and
ohci platform devices. the usbhs_init function
is defined which does the usbhs device initialization
and I/O mux of ehci and ohci.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

enabling and disabling the common clocks for ehci
and ohci is implemented. usbhs is a common parent
platform driver for EHCI and OHCI driver. This driver
receives the clock enable and disable requests
from ehci and ohci drivers.The UHH and TLL
initialization is also performed.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Create the ehci and ohci specific platform data structures.
The port enum values are made common for both ehci and ohci.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The patch below removes an extra "l" in the word.
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

On non-OMAP2 and non-OMAP3 kernel configs, turn omap2_sdrc_init() into
a no-op.  Otherwise, compilation breaks on an OMAP4-only config with
the current omap-for-linus branch:

arch/arm/mach-omap2/built-in.o: In function `omap2_init_common_devices':
../mach-omap2/io.c:421: undefined reference to `omap2_sdrc_init'

Thanks to Sergei Shtylyov <sshtylyov@mvista.com> for suggesting the use
of a empty static inline function rather than a macro.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
[tony@atomide.com: updated not to use __init for inline omap2_sdrc_init]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add omap_hwmod_setup_one(), which is intended for use early in boot to
selectively setup the hwmods needed for system clocksources and
clockevents, and any other hwmod that is needed in early boot.
omap_hwmod_setup_all() can then be called later in the boot process.
The point is to minimize the amount of code that needs to be run
early.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

Rename omap_hwmod_init() to omap_hwmod_register().  Rename
omap_hwmod_late_init() to omap_hwmod_setup_all().  Also change all of
the callers to reflect the new names.  While here, update some
copyrights.

Suggested by Tony Lindgren <tony@atomide.com>.

N.B. The comment in mach-omap2/serial.c may no longer be correct, given
     recent changes in init order.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

Add dmtimer data.
Signed-off-by: NThara Gopinath <thara@ti.com>
Signed-off-by: NTarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: NBenoit Cousson <b-cousson@ti.com>

On OMAP4, the dpll post divider outputs (MX outputs)
along with clockout_x2 output provide a way to allow/deny
hardware level autogating.
Allowing autoidle would mean that the hw would autogate
this clock when there is no dependency for it.
Denying idle would mean that this clock output will be
forced to stay enabled.

Add dpll api's to read/allow/deny idle control
for these dpll mx postdividers.

NOTE: The gatectrl bit set to 0 allows gatectrl,
and the bit set to 1 denies gatectrl.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: moved OMAP4-specific DPLL control code to
 mach-omap2/dpll44xx.c; added some documentation for CLOCK_CLKOUTX2]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Attempt to enable autoidle for as many clocks as possible in the
OMAP2+-common CONFIG_OMAP_RESET_CLOCKS code.  Currently, this only
enables DPLL autoidle for OMAP3/4 DPLLs; but future patches will
enable autoidle for other clocks and the OMAP2 DPLL/APLLs.

In the long run, we should probably get rid of
CONFIG_OMAP_RESET_CLOCKS, and unconditionally run the code that it
selects.  Otherwise, the state of the clock tree won't match the
hardware state - this could result in clocks being enabled or disabled
unpredictably.

Based on a patch by Rajendra Nayak <rnayak@ti.com> that did this in
the pm34xx.c/pm44xx.c code.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>