There is no good reason for the asymmetry in the parameters of
eth_port_uc_addr_get() and eth_port_uc_addr_set().  Make them
symmetric.  Remove some gratuitous block comments while we're here.
Signed-off-by: NGabriel Paubert <paubert@iram.es>
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This PHY support patch was written by Benjamin Li.
Signed-off-by: NBenjamin Li <benjamin.li@qlogic.com>
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The baycom_ser_fdx driver did not allow i/o ports >= 0x1000.  Now that
there are pci cards (with rs232 ports) which use for example 0xb800 this
limit should not exists.

Also, for non kernel coders find the cause of problems was challenging so I
added extra logging.
Signed-off-by: NFolkert van Heusden <folkert@vanheusden.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

strlcpy already accounts for the trailing zero in its length
computation, so there is no need to substract one to the buffer size.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Cc: Thomas Klein <osstklei@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Tested by TiCPU on irc

zd1211 chip 13b1:001e v4802 high 00-14-bf AL2230_RF pa0 g---
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using monitor mode, Johannes Berg observed out that lots of corrupted
and otherwise invalid frames were being passed to the host.

When in monitor mode we were disabling the hardware filtering here, but
this is not how monitor mode should work.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a backport of Helge Deller's recent patch for wireless-dev.git
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After 13 years of use, it looks like my email address is finally going
to disappear. While this is likely to drop the amount of incoming spam
greatly ;-), it may also affect more appropriate messages, so let's
update my email address in various places. In addition, Host AP mailing
list is subscribers-only and linux-wireless can also be used for
discussing issues related to this driver which is now shown in
MAINTAINERS.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch includes:

- code cleanup related to resource management
- extended error data gathering for resource management
- removing trailing whitespaces
Signed-off-by: NJan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The patch fixes bugs related to the probe / remove adapter
functionality (handling of OFDT nodes)
Signed-off-by: NJan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

NETPOLL support for Sibyte MAC
Signed-off-by: NManish Lachwani <mlachwani@mvista.com>
Signed-off-by: NDeepak Saxena <dsaxena@mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Remove unused variables from s2io_nic structure

- Changed the memory failure printk messages to print only in debug mode

- Updated the copyright messages

(Resending; due to patch being corrupted)
Signed-off-by: NSantosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

New version to track changes.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Do some minor rearrangement of data structures to try and optimize
cache usage.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Don't need to lock when processing transmit complete unless queue fills.
Modeled after tg3.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The following hardware error bits only show up on Genesis chipset
and are handled elsewhere, so they can be masked off.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Document that all fields must be little endian.  Use annotated types
even in the comments.  Consistently use shorter type names (u8, s8).
Realign the comments.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cleanup drivers/net/wireless/libertas/debugfs.c to use standard kernel
macros and functions.
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The way airo.c keeps track of all its devices is complicated and buggy
as well (del_airo_dev forgets to free the memory add_airo_dev allocates).
It's cleaner to use the standard list primitives.
While we're at it, it's not necessary to put PCI cards in the list, because
the kernel already keeps track of them. We can take advantage of it and
use the .remove callback as it was meant to be.
This makes /sys/bus/pci/drivers/airo/{,un}bind work.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's unnecessary to check for NULL before calling kfree().
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In code manipulating the TM State Low register of 802.11 cores, two
different magic numbers are used to reference the 'G Mode Enable' bit.
One of these, 0x20000000, is clear, but the other, (0x800 << 18), is not.
This patch replaces both types with a defined constant. In addition, two
bits in the TM State High registers are given definitions to help in
following the code.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ASUS A9Rp
Tested by Serge
zd1211b chip 0b05:171b v4802 high 00-17-31 AL2230_RF pa0 g--

ZyXEL G-202
Tested by Marcus D. Hanwell
zd1211b chip 0586:3410 v4810 high 00-13-49 AL2230_RF pa0 g---

US Robotics USR805423
Tested by Pascal S. de Kloe
FCC ID: RAXWN4501H
zd1211b chip 0baf:0121 v4810 high 00-14-c1 AL2230_RF pa0 g--N
Julien Pinon reports this also comes in AL2230S form
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ZD1211 appears to be back in production: a number of new devices have
been appearing! Some of them are using new radios.

This patch adds support for the next generation AL2230 RF chip which has
been spotted in a few new devices.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Suggested by Maxime Austruy, based on mac80211 changes from Stephen
Hemminger
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rev tulip version... things have changed since 2002!
Signed-off-by: NValerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix an annoying typo - SytemError -> SystemError
Signed-off-by: NValerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix a problem with Tulip 21142 HP branded PCI cards (PN#: B5509-66001),
which feature a NatSemi DP83840A PHY.

Without that patch, it is impossible to properly initialize the card's PHY,
and it's thus impossible to monitor/configure it.

[VAL: I'm happy with the 1.5 ms max delay; it doesn't seem excessive.]
Signed-off-by: NThibaut VARENE <varenet@parisc-linux.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Acked-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NValerie Henson <val_henson@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

From: Jim Gifford <maillist@jg555.com>, Grant Grundler <grundler@parisc-linux.org>, Peter Horton <pdh@colonel-panic.org>

With Grant's help I was able to get the tulip driver to work with 64 bit
MIPS.

[VAL: I'm happy with the 1.5 ms max delay; it doesn't seem excessive.]
Signed-off-by: NValerie Henson <val_henson@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The tc35815 driver lacks a call to pci_dma_sync_single_for_device() on
receiving.  Recent fix of MIPS dma_sync_single_for_cpu() reveal this
bug.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

use netdev_priv() instead of dev->priv
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NDon Fry <pcnet32@verizon.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The patch below moves the init_block out of the private struct and
only allocates init block with pci_alloc_consistent.

This has two effects:

1. Performance increase for non cache coherent machines, because the
   CPU only data in the private struct are now cached

2. locks are working now for platforms, which need to have locks
   in cached memory
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: NDon Fry <pcnet32@verizon.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAhmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Save/Restore unused buffer mappings in 2/3 buffer mode to avoid
frequent mapping

- Save/Restore adapter reset count during adapter reset

  (Resending; forgot to cc netdev)
Signed-off-by: NSantosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Replace kmalloc+memsetout the driver. Slightly modified by Auke Kok.
Signed-off-by: NYan Burman <burman.yan@gmail.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>