The bus reset handler really is a host reset, so move it to
eh_bus_reset_handler.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Acked-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

m68k_num_memory is unsuitable to test for the presence of FastRAM on
CT60 if the kernel is located in FastRAM: in arch/m68k/mm/motorola.c the
ST-RAM chunk is skipped and m68k_num_memory is decremented in this
case. m68k_realnum_memory still contains the actual number of RAM chunks
so use that.
Signed-off-by: NMichael Schmitz <schmitzmic@gmail.com>
Tested-by: NChristian T. Steigies <cts@debian.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The atari_scsi driver should not access Falcon DMA chip registers unless
it has acquired exclusive access to that chip. If the driver doesn't
have exclusive access then there's no need for a DMA reset as there are
no scsi commands in progress.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Avoid various warnings from "make C=1" by annotating a couple of
unlock-then-lock sequences, replacing a zero with NULL and correcting
some type casts.

Also avoid a warning from "make W=1" by adding braces.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove dead code inside #if 0 conditionals.

Remove the #ifdef __KERNEL__ test, since NCR5380.h has no definitions
that relate to userspace code.

Remove two redundant macro definitions which were overlooked in
commit e9db3198 ("sun3_scsi: Adopt NCR5380.c core driver").
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Apply prototypes to get consistent function signatures for the DMA
functions implemented in the board-specific drivers. To avoid using
macros to alter actual parameters, some of those functions are reworked
slightly.

This is a step toward the goal of passing the board-specific routines
to the core driver using an ops struct (as in a platform driver or
library module).

This also helps fix some inconsistent types: where the core driver uses
ints (cmd->SCp.this_residual and hostdata->dma_len) for keeping track of
transfers, certain board-specific routines used unsigned long.

While we are fixing these function signatures, pass the hostdata pointer
to DMA routines instead of a Scsi_Host pointer, for shorter and faster
code.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Avoid the call to NCR5380_poll_politely2() when possible. The call is
easily short-circuited on the PIO fast path, using the inline wrapper.
This requires that the NCR5380_read macro be made available before
any #include "NCR5380.h" so a few declarations have to be moved too.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For timeout values adopt unsigned long, which is the type of jiffies etc.

For chip register values and bit masks pass u8, which is the return type
of readb, inb etc.

For device register offsets adopt unsigned int, as it is suitable for
adding to base addresses.

Pass the NCR5380_hostdata pointer to the board-specific routines instead
of the Scsi_Host pointer. The board-specific code is concerned with
hardware and not with SCSI protocol or the mid-layer.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch fixes an old bug: accesses to device registers from the
interrupt handler (after reselection, DMA completion etc.) could mess
up a device register access elsewhere, if the latter takes place outside
of an irq lock (during selection etc.).
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The benefit of limiting can_queue to 1 is that atari_scsi shares the
ST DMA chip more fairly with other drivers (e.g. falcon-ide).

Unfortunately, this can limit SCSI bus utilization. On systems without
IDE, atari_scsi should issue SCSI commands whenever it can arbitrate for
the bus. Make that possible by making can_queue configurable.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This setting does not need to be conditional on Atari ST or TT.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Now that atari_scsi and sun3_scsi have been converted to use the NCR5380.c
core driver, remove atari_NCR5380.c. Also remove the last vestiges of its
Tagged Command Queueing implementation from the wrapper drivers.

The TCQ support in atari_NCR5380.c is abandoned by this patch. It is not
merged into the remaining core driver because,

1) atari_scsi defines SUPPORT_TAGS but leaves FLAG_TAGGED_QUEUING disabled
by default, which indicates that it is mostly undesirable.

2) I'm told that it doesn't work correctly when enabled.

3) The algorithm does not make use of block layer tags which it will have
to do because scmd->tag is deprecated.

4) sun3_scsi doesn't define SUPPORT_TAGS at all, yet the the SUPPORT_TAGS
macro interacts with the CONFIG_SUN3 macro in 'interesting' ways.

5) Compile-time configuration with macros like SUPPORT_TAGS caused the
configuration space to explode, leading to untestable and unmaintainable
code that is too hard to reason about.

The merge_contiguous_buffers() code is also abandoned. This was unused
by sun3_scsi. Only atari_scsi used it and then only on TT, because only TT
supports scatter/gather. I suspect that the TT would work fine with
ENABLE_CLUSTERING instead. If someone can benchmark the difference then
perhaps the merge_contiguous_buffers() code can be be justified. Until
then we are better off without the extra complexity.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add support for the Atari ST DMA chip to the NCR5380.c core driver.
This code is copied from atari_NCR5380.c.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Standardize the DMA setup hooks so that the DMA implementation in
atari_NCR5380.c can be reconciled with pseudo DMA implementation in
NCR5380.c.

Calls to NCR5380_dma_recv_setup() and NCR5380_dma_send_setup() return
a negative value on failure, zero on PDMA transfer success and a positive
byte count for DMA setup success.

This convention is not entirely new, but is now applied consistently.

Also remove a pointless Status Register access: the *phase assignment is
redundant because after NCR5380_transfer_dma() returns control to
NCR5380_information_transfer(), that routine then returns control
to NCR5380_main(), which means *phase is dead.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Only the atari_scsi and sun3_scsi drivers define DMA_MIN_SIZE.
Both drivers also define NCR5380_dma_xfer_len, which means
DMA_MIN_SIZE can be removed from the core driver.

This removes another discrepancy between the two core drivers.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For the NCR5380.c core driver, these macros are never used.
If REAL_DMA were to be defined, compilation would fail.

For the atari_NCR5380.c core driver, REAL_DMA is always defined.

Hence these macros are pointless.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This refactoring removes two global Scsi_Host pointers. This
improves consistency with other ncr5380 drivers. Adopting the same
conventions as the other drivers makes them easier to read.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The NCR5380 drivers have a home-spun linked list implementation for
scsi_cmnd structs that uses cmd->host_scribble as a 'next' pointer. Adopt
the standard list_head data structure and list operations instead. Remove
the eh_abort_handler rather than convert it. Doing the conversion would
only be churn because the existing EH handlers don't work and get replaced
in a subsequent patch.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Some NCR5380 hosts offer a .show_info method to access the contents of
the various command list data structures from a procfs file. When NDEBUG
is set, the same information is sent to the console during EH.

The two core drivers, atari_NCR5380.c and NCR5380.c differ here. Because
it is just for debugging, the easiest way to fix the discrepancy is
simply remove this code.

The only remaining users of NCR5380_show_info() and NCR5380_write_info()
are drivers that define PSEUDO_DMA. The others have no use for the
.show_info method, so don't initialize it.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add missing .module initializer. Use distinct .proc_name values for the
g_NCR5380 and g_NCR5380_mmio modules. Remove pointless CAN_QUEUE and
CMD_PER_LUN override macros. Cleanup whitespace and code style.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove unused includes (stat.h, signal.h, proc_fs.h) and move includes
needed by the core drivers into the common header (delay.h etc).
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Allocate a work queue that will permit busy waiting and sleeping. This
means NCR5380_init() can potentially fail, so add this error path.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The atari_NCR5380.c core driver now takes care of bus reset upon driver
initialization if required (same as NCR5380.c). Move the Toshiba CD-ROM
support into the core driver, enabled with a host flag, so that all
NCR5380 drivers can make use of it.

Drop the RESET_BOOT macros and the ATARI_SCSI_RESET_BOOT and
ATARI_SCSI_TOSHIBA_DELAY Kconfig symbols, which are now redundant.

Remove the atari_scsi_reset_boot(), mac_scsi_reset_boot() and
sun3_scsi_reset_boot() routines. None of this duplicated code is needed
now that all drivers can use NCR5380_maybe_reset_bus().

This brings atari_scsi, mac_scsi and sun3_scsi into line with all of the
other NCR5380 drivers.

The bus reset may raise an interrupt. That would be new behaviour for
atari_scsi only when CONFIG_ATARI_SCSI_RESET_BOOT=n. The ST DMA interrupt
is not assigned to atari_scsi at this stage, so
CONFIG_ATARI_SCSI_RESET_BOOT=y may well be problematic already.
Regardless, do_reset() now raises and clears the interrupt within
local_irq_save/restore which should avoid problems.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The NVRAM location of this byte is 16, as documented in
http://toshyp.atari.org/en/004009.html

This was confirmed by Michael Schmitz, by setting the SCSI host ID
under EmuTOS and then checking the value in /proc/driver/nvram and
/dev/nvram under Linux.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This platform_driver does not need to set an owner, it will be populated by
the driver core.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Unlike NCR5380.c, the atari_NCR5380.c core driver is limited to a single
instance because co-routine state is stored globally.

Fix this by removing the static scsi host pointer. For the co-routine,
obtain this pointer from the work_struct pointer instead. For the interrupt
handler, obtain it from the dev_id argument.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The static variable setup_use_tagged_queuing is declared in mac_scsi.c,
sun3_scsi.c and atari_scsi.c and doesn't belong in the core driver.
None of the other NCR5380 drivers suffer from this layering issue which
makes merging the core drivers more difficult and will likely hinder plans
for future use of platform data to configure the driver.

Replace the static variable with a host flag. This way it can be reported
along with the other flags.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

There is very little difference between the sun3_NCR5380.c core driver
and atari_NCR5380.c. The former is a fork of the latter.

Merge the sun3_NCR5380.c core driver into atari_NCR5380.c so that
sun3_scsi.c can adopt the latter and the former can be deleted.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Simplify falcon_release_lock_if_possible() by making callers responsible for
disabling local IRQ's, which they must do anyway to correctly synchronize
the ST DMA "lock" with core driver data structures. Move this
synchronization logic to the core driver with which it is tightly coupled.

Other LLD's like sun3_scsi and mac_scsi that can make use of this core
driver can just stub out the NCR5380_acquire_dma_irq() and
NCR5380_release_dma_irq() calls so the compiler will eliminate the
ST DMA code.

Remove a redundant local_irq_save/restore pair (irq's are disabled for
interrupt handlers these days). Revise the locking for
atari_scsi_bus_reset(): use local_irq_save/restore() instead of
atari_turnoff/turnon_irq(). There is no guarantee that atari_scsi still
holds the ST DMA lock during EH, so atari_turnoff/turnon_irq() could
end up dropping an IDE or floppy interrupt.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Make the atari_NCR5380.c core driver usable by sun3_scsi, mac_scsi and
others by moving some of the Falcon-specific code out of the core driver:
!IS_A_TT, atari_read_overruns and falcon_dont_release. Replace these with
hostdata variables and flags. FLAG_CHECK_LAST_BYTE_SENT is unused in
atari_NCR5380.c so don't set it.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

atari_NCR5380.c enables its IRQ when it is already enabled. Sun3 doesn't
use the ENABLE_IRQ/DISABLE_IRQ cruft. Remove it.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The #defines in atari_scsi.h are intended to influence subsequent #includes
in atari_scsi.c. IMHO, that's too convoluted.

Remove atari_scsi.h by moving those macro definitions to atari_scsi.c,
consistent with other NCR5380 drivers.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Convert atari_scsi to platform device and eliminate scsi_register().

Validate __setup options later on so that module options are checked as well.

Remove the comment about the scsi mid-layer disabling the host irq as it
is no longer true (AFAICT). Also remove the obsolete slow interrupt stuff
(IRQ_TYPE_SLOW == 0 anyway).
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Don't disable irqs when waiting for the ST DMA "lock"; its release may
require an interrupt.

Introduce stdma_try_lock() for use in soft irq context. atari_scsi now tells
the SCSI mid-layer to defer queueing a command if the ST DMA lock is not
available, as per Michael's patch:
http://marc.info/?l=linux-m68k&m=139095335824863&w=2

The falcon_got_lock variable is race prone: we can't disable IRQs while
waiting to acquire the lock, so after acquiring it there must be some
interval during which falcon_got_lock remains false. Introduce
stdma_is_locked_by() to replace falcon_got_lock.

The falcon_got_lock tests in the EH handlers are incorrect these days. It
can happen that an EH handler is called after a command completes normally.
Remove these checks along with falcon_got_lock.

Also remove the complicated and racy fairness wait queues. If fairness is an
issue (when SCSI competes with IDE for the ST DMA interrupt), the solution
is likely to be a lower value for host->can_queue.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Convert Scsi_Cmnd to struct scsi_cmnd and drop the #include "scsi.h".
The sun3_NCR5380.c core driver already uses struct scsi_cmnd so converting
the other core drivers reduces the diff which makes them easier to unify.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Compile-time override of scsi host defaults is pointless for drivers that
provide module parameters and __setup options for that. Too many macros make
the code hard to read so remove them.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

If the host->info() method is not set, then host->name is used by default.
For atari_scsi, that is exactly the same text. So remove the redundant
info() method. Keep sun3_scsi.c in line with atari_scsi.

Some NCR5380 drivers return an empty string from the info() method
(arm/cumana_1.c arm/oak.c mac_scsi.c) while other drivers use the default
(dmx3191d dtc.c g_NCR5380.c pas16.c t128.c).

Implement a common info() method to replace a lot of duplicated code which
the various drivers use to announce the same information.

This replaces most of the (deprecated) show_info() output and all of the
NCR5380_print_info() output. This also eliminates a bunch of code in
g_NCR5380 which just duplicates functionality in the core driver.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Every NCR5380 driver sets AUTOSENSE so it need not be optional (and the
mid-layer expects it). Remove this redundant macro to improve readability.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Make use of the host template static initializer instead of assigning
handlers at run-time. Move __maybe_unused qualifiers from declarations
to definitions. Move the atari_scsi_bus_reset() wrapper after the
definition of NCR5380_bus_reset(). All of the host template handler
prototypes are now redundant so remove them.

The write_info() handler is only relevant to drivers using PSEUDO_DMA so
this patch fixes the compiler warning in atari_NCR5380.c and sun3_NCR5380.c:

  CC      drivers/scsi/atari_scsi.o
  drivers/scsi/NCR5380.h:329: warning: 'NCR5380_write_info' declared 'static' but never defined
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Add missing static qualifiers and remove the now pointless prototypes. The
NCR5380_* prototypes are all declared in NCR5380.h and renamed using macros.
Further declarations are redundant (some are completely unused). Remove
them.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>