This acts as a reversion of 1c6b2ca5 in
the case of UP SH-4, where we still have the risk of a multiple hit
between the slow and fast paths. As seen on SH7780.
Signed-off-by: NHideo Saito <saito@densan.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use generic_io_base to point out the pci io window, and make sure the
highest port address used is SH7751_PCI_IO_SIZE - 1.

This patch fixes pci io port access for the r2d boards - CONFIG_8139TOO_PIO
now works as expected. So does the alsa driver for CMI8738.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NKatsuya MATSUBARA <matsu@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch makes sure ctrl_inN/outN are used instead of inN/outN for on chip
pci registers. Without this patch addresses may be adjusted using the value
in generic_io_base. This patch makes it possible to set generic_io_base and
have pci without reading and writing all over the place.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NKatsuya MATSUBARA <matsu@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Reported-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

sh64 doesn't provide __uncached_start, so don't reference it
unconditionally.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

A number of cleanups to get the SH-5 cache management code in line with
the rest of the SH backend.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Reported-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Previously this took an explicit range, update this to use the same
behaviour as the rest of the SH parts where we simply flush out a line
from the start address.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

All SH-5 machines are little endian.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds sh7366 cpu supports. Just the most basic things like interrupt
controller, clocks and serial port are included at this point.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch removes the maskreg irq code since it is not in use anymore.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch makes the 32-bit ptrace code compile again.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch converts the highlander CF device from good old machvec readb/writeb
to the new shiny trapped io.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch converts the CF device on r2d boards from machvec readb/writeb
to trapped io.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The idea is that we want to get rid of the in/out/readb/writeb callbacks from
the machvec and replace that with simple inline read and write operations to
memory. Fast and simple for most hardware devices (think pci).

Some devices require special treatment though - like 16-bit only CF devices -
so we need to have some method to hook in callbacks.

This patch makes it possible to add a per-device trap generating filter. This
way we can get maximum performance of sane hardware - which doesn't need this
filter - and crappy hardware works but gets punished by a performance hit.

V2 changes things around a bit and replaces io access callbacks with a
simple minimum_bus_width value. In the future we can add stride as well.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Update the defconfigs for r2d-plus and r2d-1 since we now have new drivers
for sm501 usb, spi-over-sci and epson r9701 rtc in mainline.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch converts the unaligned access handling code to use opcode_t
instead of u16. While at it, enable unaligned access handling for sh2a.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds byte support to the sign extension code. Unaligned access
traps should never be generated on 8-bit io operations, but we will use this
code for trapped io and we do need byte support there.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

move update_process_times() out from under xtime_lock.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds basic support for the Migo-R board.

Only simple stuff provided by the cpu specific sh7722 code is in place now,
like serial console port, timers and usb gadget. There is also partial support
for the smc91c111 ethernet controller - unfortunately some driver header file
also needs patching (not included here) to make the driver get IRQ sense
information from the platform data.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Break out the sign extension code since it's used in multiple places.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds support for sh7722 devices with prr value 0xa1.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds the base address of SCIF0 in the case of sh7722.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

now that platform_device_register_simple() takes a "const chat *".
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch fixes the recently introduced declared coherent memory support.
Without this fix a cached memory area is returned by dma_alloc_coherent() -
unless dma_declare_coherent_memory() has setup a separate area.

This patch makes sure an uncached memory area is returned. With this patch
it is now possible to ping through an rtl8139 interface on r2d-plus.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Commit d3d74453 ("hrtimer: fixup the
HRTIMER_CB_IRQSAFE_NO_SOFTIRQ fallback") broke several archs, and since
only Russell bothered to merge the fix, and Greg to ACK his arch, I'm
sending this for merger.

I have confirmation that the Alpha bit results in a booting kernel.
That leaves: blackfin, frv, sh and sparc untested.

The deadlock in question was found by Russell:

  IRQ handle
    -> timer_tick() - xtime seqlock held for write
      -> update_process_times()
        -> run_local_timers()
          -> hrtimer_run_queues()
            -> hrtimer_get_softirq_time() - tries to get a read lock

Now, Thomas assures me the fix is trivial, only do_timer() needs to be
done under the xtime_lock, and update_process_times() can savely be
removed from under it.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
CC: Richard Henderson <rth@twiddle.net>
CC: Bryan Wu <bryan.wu@analog.com>
CC: David Howells <dhowells@redhat.com>
CC: Paul Mundt <lethal@linux-sh.org>
CC: William Irwin <wli@holomorphy.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

To allow flexible configuration of IDE introduce HAVE_IDE.
All archs except arm, um and s390 unconditionally select it.
For arm the actual configuration determine if IDE is supported.

This is a step towards introducing drivers/Kconfig for arm.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Acked-by: NRussell King - ARM Linux <linux@arm.linux.org.uk>
Acked-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Using "attr" twice is not OK, because it effectively prohibits such
container_of() on variables not named "attr".
Signed-off-by: NAlexey Dobriyan <adobriyan@sw.ru>
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Mark arches that support A.OUT format by including the following in their
master Kconfig files:

	config ARCH_SUPPORTS_AOUT
		def_bool y

This should also be set if the arch provides compatibility A.OUT support for
an older arch, for instance x86_64 for i386 or sparc64 for sparc.

I've guessed at which arches don't, based on comments in the code, however I'm
sure that some of the ones I've marked as 'yes' actually should be 'no'.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the BOOTMEM_EXCLUSIVE, introduced in the previous patch, to avoid
conflicts while reserving the memory for the kdump capture kernel
(crashkernel=).
Signed-off-by: NBernhard Walle <bwalle@suse.de>
Cc: <linux-arch@vger.kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patchset adds a flags variable to reserve_bootmem() and uses the
BOOTMEM_EXCLUSIVE flag in crashkernel reservation code to detect collisions
between crashkernel area and already used memory.

This patch:

Change the reserve_bootmem() function to accept a new flag BOOTMEM_EXCLUSIVE.
If that flag is set, the function returns with -EBUSY if the memory already
has been reserved in the past.  This is to avoid conflicts.

Because that code runs before SMP initialisation, there's no race condition
inside reserve_bootmem_core().

[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix powerpc build]
Signed-off-by: NBernhard Walle <bwalle@suse.de>
Cc: <linux-arch@vger.kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Cc: David Howells <dhowells@redhat.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After seeing the filename I'd have expected something about the
implementation of SMP in the Linux kernel - not some notes on kernel
configuration and building trivialities noone would search at this
place.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NAlan Cox <alan@redhat.com>