Fix an Oops, triggering, if the DMA buffer allocation for the Rx channel in
sh-sci.c fails.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver.  This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.

This patch is a pretty mechanical change.  The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial.  This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NSean MacLennan <smaclennan@pikatech.com>

Use the resource_size function instead of manually calculating the
resource size. This actually fixes an off-by-one error.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add an UART driver for the UART component available as a SOPC (System on
Programmable Chip) component for Altera FPGAs.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add an UART driver for the JTAG UART component available as a SOPC
(System on Programmable Chip) component for Altera FPGAs.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix a problem in early versions of the FPGA IP.

In certain situations the IP reports that the FIFO is empty, but a byte is
still clocked out.  If a flush is done at that point the currently clocked
byte is canceled.

This causes incompatibilities with the upper layers when a port is closed,
it waits until the FIFO is empty and then closes the port.  During close
the FIFO is flushed -> the last byte is not sent properly.

Now the FIFO is only flushed if it is reported to be non-empty.  Which
makes the currently clocked out byte to finish.

[akpm@linux-foundation.org: fix build]
Signed-off-by: NRichard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

CTS is a read only bit and we are to stop signal RTS if modem line
TIOCM_RTS is not set.

Thanks for suggestions by Richard Röjfors.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NRichard Röjfors <richard.rojfors@pelagicore.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Byte accesses for I/O devices in Xilinx IP is going to be less
desired in the future such that the driver is being changed to
use 32 bit accesses.

This change facilitates using the uartlite IP over a PCIe bus
which only allows 32 bit accesses.
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Tested-by: NMichal Simek <monstr@monstr.eu>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The BF54xM procs imply the related BF54x define, so no need to check both.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Should be stable now ...
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now that the SPORT MMR defines have been unified, switch over to it.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Rather than always turn on the SPORT TX interrupt, only do it when we've
actually queued up data for transmission.  This avoids useless interrupt
processing.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

These were all copied over from the Blackfin UART driver, but they don't
make sense here because these bits are all specific to the Blackfin UART.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Need to initialize the SPORT state rather than using random memory.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Common serial API says we need to grab the port lock before modifying
the port state to prevent inconsistent state between threads.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some people need flow control on their ports, so now boards can support
that via any GPIOs.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Clarifies command line set up for devices between consoles and early
devices.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The driver doesn't care about this, but the common serial core wants it.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

All the resources are in the boards files now.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The waiting loop to stop SPORT TX from TX interrupt is too long.  This may
block the SPORT RX interrupts and cause the RX FIFO to overflow. So, do
stop sport TX only after the last char in TX FIFO is moved into the shift
register.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We cannot let a 32-bit RX FIFO read be interrupted otherwise a fake RX
underflow error might be generated.

URL: http://blackfin.uclinux.org/gf/tracker/5145Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The ekgdboc= differs from kgdboc= in that you can begin debuggin as
soon as the exceptions are setup and the kgdb I/O driver is available,
instead of waiting until the tty subsystem is available.

CC: kgdb-bugreport@lists.sourceforge.net
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

If kdb is open on a serial port that is not actually a console make
sure to call the poll routines to emit and receive characters.
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Acked-by: NMartin Hicks <mort@sgi.com>

This patch adds in the kdb PS/2 keyboard driver.  This was mostly a
direct port from the original kdb where I cleaned up the code against
checkpatch.pl and added the glue to stitch it into kgdb.

This patch also enables early kdb debug via kgdbwait and the keyboard.

All the access to configure kdb using either a serial console or the
keyboard is done via kgdboc.

If you want to use only the keyboard and want to break in early you
would add to your kernel command arguments:

    kgdboc=kbd kgdbwait

If you wanted serial and or the keyboard access you could use:

    kgdboc=kbd,ttyS0

You can also configure kgdboc as a kernel module or at run time with
the sysfs where you can activate and deactivate kgdb.

Turn it on:
    echo kbd,ttyS0 > /sys/module/kgdboc/parameters/kgdboc

Turn it off:
    echo "" > /sys/module/kgdboc/parameters/kgdboc
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Reviewed-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Allow kgdboc to work on sparc hardware with the Zilog serial chips.
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>

The sci_poll_get_char() needs to return immediately if there is no
input from the chip to process, and must return a value of
NO_POLL_CHAR.

This allows kgdboc to process multiple polled devices while kgdb is
active.
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>

The design of the kdb shell requires that every device that can
provide input to kdb have a polling routine that exits immediately if
there is no character available.  This is required in order to get the
page scrolling mechanism working.

Changing the kernel debugger I/O API to require all polling character
routines to exit immediately if there is no data allows the kernel
debugger to process multiple input channels.

NO_POLL_CHAR will be the return code to the polling routine when ever
there is no character available.

CC: linux-serial@vger.kernel.org
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

Remove unnecessary Kconfig entry. S5PC100 has exactly the same driver as
S3C6400/S3C6410/S5P6440.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated.  This patch
makes all readers of these elements use device.of_node instead.

(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This adds an argument to the DMAengine control function, so that
we can later provide control commands that need some external data
passed in through an argument akin to the ioctl() operation
prototype.

[dan.j.williams@intel.com: fix up some missed conversions]
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The imx CTS trigger level is left at its reset value that is 32
chars. Since the RX FIFO has 32 entries, when CTS is raised, the
FIFO already is full. However, some serial port devices first empty
their TX FIFO before stopping when CTS is raised, resulting in lost
chars.

This patch sets the trigger level lower so that other chars arrive
after CTS is raised, there is still room for 16 of them.

Signed-off-by: Valentin Longchamp<valentin.longchamp@epfl.ch>
Tested-by: Philippe Rétornaz<philippe.retornaz@epfl.ch>
Acked-by: Wolfram Sang<w.sang@pengutronix.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 6acc6833
introduced NULL pointer dereference and kernel crash
on ppc32 machines while booting. Fix this bug now.
Reported-by: NLeonardo Chiquitto <leonardo.lists@gmail.com>
Tested-by: NLeonardo Chiquitto <leonardo.lists@gmail.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

dev_node_t was only used to transport some minor/major numbers
from the PCMCIA device drivers to deprecated userspace helpers.
However, only a few drivers made use of it, and the userspace
helpers are deprecated anyways. Therefore, get rid of dev_node_t .

As a first step, remove any usage of dev_node_t from drivers which
only wrote to this typedef/struct, but did not make use of it.

CC: linux-bluetooth@vger.kernel.org
CC: Harald Welte <laforge@gnumonks.org>
CC: linux-mtd@lists.infradead.org
CC: linux-wireless@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: alsa-devel@alsa-project.org
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Instead of the old pcmcia_request_irq() interface, drivers may now
choose between:

- calling request_irq/free_irq directly. Use the IRQ from *p_dev->irq.

- use pcmcia_request_irq(p_dev, handler_t); the PCMCIA core will
  clean up automatically on calls to pcmcia_disable_device() or
  device ejection.

- drivers still not capable of IRQF_SHARED (or not telling us so) may
  use the deprecated pcmcia_request_exclusive_irq() for the time
  being; they might receive a shared IRQ nonetheless.

CC: linux-bluetooth@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: linux-usb@vger.kernel.org
CC: linux-ide@vger.kernel.org
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

UARTs in the S3C2416 are almost same as in S3C2443 and can be handled by
s3c2440 serial driver.
Signed-off-by: NYauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Final version of the patch that adds support for RS485 communications to the atmel_serial driver.

The patch has been already sent and discussed on both linux-kernel and linux-arm-kernel mailing lists several times.

Many people collaborated to improve and test the code:
Tested-by: NSebastian Heutling <Sebastian.Heutling@who-ing.de>
Tested-by: NBernhard Roth <br@pwrnet.de>
Reviewed-by: NRyan Mallon <ryan@bluewatersys.com>
Signed-off-by: NClaudio Scordino <claudio@evidence.eu.com>
Signed-off-by: NMichael Trimarchi <michael@evidence.eu.com>
Signed-off-by: NRick Bronson <rick@efn.org>
Signed-off-by: NSebastian Heutling <Sebastian.Heutling@who-ing.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

In an error handling case the lock is not unlocked.

A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression E1;
identifier f;
@@

f (...) { <+...
* spin_lock_irqsave (E1,...);
... when != E1
* return ...;
...+> }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add Fujitsu Wacom 1FGT Tablet PC device
Signed-off-by: NPing Cheng <pingc@wacom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Most things mentioned are either obsolete (platform-support) or wrong (device
numbering, DCD spport) these days. The remaining rest is obvious.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add add_preferred_console() to ks8695_console_init() to
enable the console
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>