Current address translation methods can produce wrong results, because
virt_to_bus and vice versa may not produce correct offsets on dma-allocated
memory. The right way is, while tracking both phys and virt address of the
window that has been allocated for boffer descriptors, and use those
numbers to compute the offset and make translation properly.
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This is intended to make the driver code more generic and flexible,
to get rid of board-specific layouts within driver, and generic rehaul,
yet keeping compatibility with the existing stuff utilizing it, being
compatible with legacy behavior (but with complaints that legacy mode
used).
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This replaces old direct usage of tty->flip stuff with relative flip API
calls.
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Convert usage of SERIAL_IO_* to UPIO_*.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

while using SCC as uart and as serial console at same time I got this:

[  138.214258] Oops: kernel access of bad area, sig: 11 [#1]
[  138.218832] PREEMPT
[  138.221021] NIP: C0105C48 LR: C0105E60 SP: C03D5D10 REGS: c03d5c60 TRAP: 0300    Not tainted
[  138.229280] MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
[  138.234713] DAR: 00000000, DSISR: C0000000
[  138.238745] TASK = c0349420[693] 'sh' THREAD: c03d4000
[  138.243754] Last syscall: 6
[  138.246402] GPR00: FEFFFFFF C03D5D10 C0349420 C01FB094 00000011 00000000 C1ECFBBC C01F24B0
[  138.254602] GPR08: FF002820 00000000 FF0028C0 00000000 19133615 A0CBCD5E 02000300 00000000
[  138.262804] GPR16: 00000000 01FF9E4C 00000000 7FA9A770 00000000 00000000 1003E2A8 00000000
[  138.271003] GPR24: 100562F4 7F9B6EF4 C0210000 C02A5338 C01FB094 00000000 C01FB094 C1F14574
[  138.279376] NIP [c0105c48] cpm_uart_tx_pump+0x4c/0x22c
[  138.284419] LR [c0105e60] cpm_uart_start_tx+0x38/0xb0
[  138.289361] Call trace:
[  138.291762]  [c0105e60] cpm_uart_start_tx+0x38/0xb0
[  138.296547]  [c010277c] uart_send_xchar+0x88/0x118
[  138.301244]  [c01029a0] uart_unthrottle+0x6c/0x138
[  138.305942]  [c00ece10] check_unthrottle+0x60/0x64
[  138.310641]  [c00ecec4] reset_buffer_flags+0xb0/0x138
[  138.315595]  [c00ecf64] n_tty_flush_buffer+0x18/0x78
[  138.320465]  [c00e81b0] tty_ldisc_flush+0x64/0x7c
[  138.325078]  [c010410c] uart_close+0xf0/0x2c8
[  138.329348]  [c00e9c48] release_dev+0x724/0x8d4
[  138.333790]  [c00e9e18] tty_release+0x20/0x3c
[  138.338061]  [c006e544] __fput+0x178/0x1e0
[  138.342076]  [c006c43c] filp_close+0x54/0xac
[  138.346261]  [c0002d90] ret_from_syscall+0x0/0x44
[  138.352386] note: sh[693] exited with preempt_count 2

a easy way to reproduce it is log into the system using ssh and do:
	cat >/dev/ttyCPM0
then, switch to minicom and write some stuff on it back to ssh, a control C
produce the oops

this happens because uart_close calls uart_shutdown which frees xmit.buf,
currently used by xchar sending in cpm_uart_tx_pump(), which seems wrong.

the attached patch fixes the oops and also fixes xchar sending.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Changed jobs and the Freescale address is no longer valid.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Base addess register for SMC 1 and 2 are never initialized.  This means
that they will not work unless a bootloader already configured them.

The DPRAM already have space reserved, this patch just makes sure the base
addess register is updated correctly on initialization.
Signed-off-by: NRune Torgersen <runet@innovsys.com>
Signed-off-by: NKumar Gala <kumar.gala@freescale.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

use schedule_timeout instead of direct call to schedule
Signed-off-by: NMarcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: NKumar Gala <kumar.gala@freescale.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The 2nd serial port on the MPC8560 ADS was not being configured correctly
and thus could not be used as a console.  Updated the defconfig for the
board to configure the proper SCC channel for the 2nd serial port.
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NKumar Gala <kumar.gala@freescale.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fixed problems so we can build with gcc-4.0.1
Signed-off-by: NPeter Schaefer-Hutter <peter.schaefer-hutter@tfk-racoms.com>
Signed-off-by: NKumar Gala <kumar.gala@freescale.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

* Makes dpram allocations work
* Makes non-console UART work on both 8xx and 82xx
* Fixed whitespace in files that were touched
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: NPantelis Antoniou <panto@intracom.gr>
Signed-off-by: NKumar Gala <kumar.gala@freescale.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

m8xx_cpm_hostalloc() can't rely on using the coherent DMA allocator early
on boot because the VM is not fully up yet.  Change it to use the on-board
DPRAM instead.

The current code relies on the "bootmem_page" allocated by
m8xx_cpm_reset(), which must be killed.

This is done in v2.4 but has never been forward ported to v2.6.
Signed-off-by: NMarcelo Tosatti <marcelo.tosatti@cyclades.com>
Cc: Pantelis Antoniou <panto@intracom.gr>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch adds the Freescale MPC86xADS board support.  The supported
devices are SMC UART and 10Mbit ethernet on SCC1.

The manual for the board says that it "is compatible with the MPC8xxFADS
for software point of view".  That's why this patch extends FADS instead of
introducing a new platform.

FEC is not supported as the "combined FCC/FEC ethernet driver" driver by
Pantelis Antoniou should replace the current FEC driver.
Signed-off-by: NGennadiy Kurtsman <gkurtsman@ru.mvista.com>
Signed-off-by: NAndrei Konovalov <akonovalov@ru.mvista.com>
Acked-by: NTom Rini <trini@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Adds SCC2 pin routing specific to the GP3 board.
Signed-off-by: NMatt Porter <mporter@kernel.crashing.org>
Signed-off-by: NKumar Gala <kumar.gala@freescale.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!