When attaching an imx28 or imx53 in USB gadget mode to a Windows host and
starting a rndis connection we see this message every 4-10 seconds:

    g_ether gadget: high speed config #2: RNDIS

Analysis shows that each time this message is printed, the rndis connection is
re-establish due to a reset because of a stalled endpoint (ep 0, dir 1). The
endpoint is stalled because the reqeust complete bit on that endpoint is set,
but in isr_tr_complete_low() the endpoint request list (mEp->qh.queue) is
empty.

This patch removed this check, because the code doesn't take the following
situation into account:

The loop over all endpoints in isr_tr_complete_handler() will call ep_nuke() on
both ep0/dir0 and ep/dir1 in the first loop. Pending reqeusts will be flushed
and completed here. There seems to be a race condition, the request is nuked,
but the request complete bit will be set, too. The subsequent check (in
ep0/dir1's loop cycle) for endpoint request list (mEp->qh.queue) empty will
fail.

Both other mainline chipidea drivers (mv_udc_core.c and fsl_udc_core.c) don't
have this check.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If udc_start() fails the qh_pool dma-pool cannot be closed because
it's still in use. This patch factors out the dma_pool_free() loop
into destroy_eps() and calls it in the error path of udc_start(),
too.

Cc: stable <stable@vger.kernel.org>
Reviewed-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes the error path of udc_start(). Now NULL is used to
unset the peripheral with otg_set_peripheral().

Cc: stable <stable@vger.kernel.org>
Reviewed-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add function to physicaly enable or disable of pullup connection on the USB-D+
line. The uvc gaget will fail, if this function is not implemented.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch changes the setup of the endpoint maxpacket size. All non control
endpoints are initialized with an undefined ((unsigned short)~0) maxpacket
size. The maxpacket size of Endpoint 0 will be kept at CTRL_PAYLOAD_MAX.

Some gadget drivers check for the maxpacket size before they enable the
endpoint, which leads to a wrong state in these drivers.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit ff823c79 ("usb: move children
to struct usb_port") forgot to consider the hub_disconnect sequence,
which releases ports before quiescing the hub, which will lead to a
use-after-free, since hub_quiesce() will try to disconnect ports'
children, which are already deallocated. Simple modprobe dummy_hcd &&
rmmod dummy_hcd will illustrate the problem.

This patch moves deallocation of hub's ports after hub_quiesce() call
in hub_disconnect().

Cc: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As NOP device node is now added in am33xx tree so remove the call
which creates the NOP platform_device.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NSanthapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Added device tree support for dsps musb glue driver and updated the
Documentation with device tree binding information.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NSanthapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: NRavi Babu <ravibabu@ti.com>
[afzal@ti.com: use '-' instead of '_' for dt properties]
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

AM335x and TI81xx platform has dual musb controller so updating the
musb_dspc.c to support the same.

Changes:
        - Moved otg_workaround timer to glue structure
        - Moved static local variable last_timer to glue structure
        - PHY on/off related cleanups
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NSanthapuri, Damodar <damodar.santhapuri@ti.com>
[afzal@ti.com: remove control module related modifications]
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Moved global variable "musb_debugfs_root" and static variable
"old_state" to 'struct musb' to help support multi instance of
musb controller as present on AM335x platform.

Also removed the global variable "orig_dma_mask" and filled the
dev->dma_mask with parent device's dma_mask.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NSanthapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Added musb_ida in musb_core.c to manage the multi core ids.
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NSanthapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Added device tree support for omap musb driver and updated the
Documentation with device tree binding information.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The glue layer should directly write to mailbox register (present in
control module) instead of calling phy layer to write to mailbox
register. Writing to mailbox register notifies the core of events like
device connect/disconnect.

Currently writing to control module register is taken care in this
driver which will be removed once the control module driver is in place.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Because the IRQF_DISABLED as the flag is now a NOOP and has been
deprecated and in hardirq context the interrupt is disabled.

so in usb/host code:
Removing the usage of flag IRQF_DISABLED;
Removing the calling local_irq save/restore actions in irq
handler usb_hcd_irq();
Signed-off-by: Nliu chuansheng <chuansheng.liu@intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds two sysfs files for each usb hub port to allow userspace
to control the port power policy.

For an upcoming Intel xHCI roothub, this will translate into ACPI calls
to completely power off or power on the port.  As a reminder, when these
ports are completely powered off, the USB host and device will see a
physical disconnect.  All future USB device connections will be lost,
and the device will not be able to signal a remote wakeup.

The control sysfs file can be written to with two options:
"on" - port power must be on.
"off" - port must be off.

The state sysfs file reports usb port's power state:
"on" - powered on
"off" - powered off
"error" - can't get power state

For now, let userspace dictate the port power off policy.  Future
patches may add an in-kernel policy.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Alan Stern pointed out that a USB port could potentially get powered off
when the attached USB device is in the middle of enumerating, due to
race conditions:
	http://marc.info/?l=linux-usb&m=134130616707548&w=2

If that happens, we need to ensure the enumeration fails.  If a call to
usb_get_descriptor() fails for a reason other than a Stall, return an
error.  That should handle the case where the port is powered off.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Upcoming Intel systems will have an ACPI method to control whether a USB
port can be completely powered off.  The implication of powering off a
USB port is that the device and host sees a physical disconnect, and
subsequent port connections and remote wakeups will be lost.

Add a new function, usb_acpi_power_manageable(), that can be used to
find whether the usb port has ACPI power resources that can be used to
power on and off the port on these machines. Also add a new function
called usb_acpi_set_power_state() that controls the port power via these
ACPI methods.

When the USB core calls into the xHCI hub driver to power off a port,
check whether the port can be completely powered off via this new ACPI
mechanism.  If so, call into these new ACPI methods.  Also use the ACPI
methods when the USB core asks to power on a port.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes the xHCI roothub code handle the clear PORT_POWER
feature request.  Setting port power is already handled.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In the upcoming USB port power off patches, we need to know whether a
USB port can ever see a disconnect event.  Often USB ports are internal
to a system, and users can't disconnect USB devices from that port.
Sometimes those ports will remain empty, because the OEM chose not to
connect an internal USB device to that port.

According to ACPI Spec 9.13, PLD indicates whether USB port is
user visible and _UPC indicates whether a USB device can be connected to
the USB port (we'll call this "connectible").  Here's a matrix of the
possible combinations:

Visible Connectible
		Name		Example
-------------------------------------------------------------------------

Yes	No	Unknown		(Invalid state.)

Yes	Yes	Hot-plug	USB ports on the outside of a laptop.
				A user could freely connect and disconnect
				USB devices.

No	Yes	Hard-wired	A USB modem hard-wired to a port on the
				inside of a laptop.

No	No	Not used	The port is internal to the system and
				will remain empty.

Represent each of these four states with an enum usb_port_connect_type.
The four states are USB_PORT_CONNECT_TYPE_UNKNOWN,
USB_PORT_CONNECT_TYPE_HOT_PLUG, USB_PORT_CONNECT_TYPE_HARD_WIRED, and
USB_PORT_NOT_USED.  When we get the USB port's acpi_handle, store the
state in connect_type in struct usb_port.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In the ACPI DSDT table, only usb root hub and usb ports are ACPI device
nodes.  Originally, we bound the usb port's ACPI node to the usb device
attached to the port.  However, we want to access those ACPI port
methods when the port is empty, and there's no usb_device associated
with that port.

Now that the usb port is a real device, we can bind the port's ACPI node
to struct usb_port instead.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The usb_device structure contains an array of usb_device "children".
This array is only valid if the usb_device is a hub, so it makes no
sense to store it there.  Instead, store the usb_device child
in its parent usb_port structure.

Since usb_port is an internal USB core structure, add a new function to
get the USB device child, usb_hub_find_child().  Add a new macro,
usb_hub_get_each_child(), to iterate over all the children attached to a
particular USB hub.

Remove the printing the USB children array pointer from the usb-ip
driver, since it's really not necessary.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch turns each USB port on a hub into a new struct device.  This
new device has the USB hub interface device as its parent.  The port
devices are stored in a new structure (usb_port), and an array of
usb_ports are dynamically allocated once we know how many ports the USB
hub has.

Move the port_owner variable out of usb_hub and into this new structure.

A new file will be created in the hub interface sysfs directory, so
add documentation.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The kernel's version number is used as decimal in the bcdDevice field of
the RH descriptor. For kernel version v3.12 we would see 3.0c in lsusb.
I am not sure how important it is to stick with bcd values since this is
this way since we started git history and nobody complained (however back
then we reported only 2.6).
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Apps which deal with devices which also have a kernel driver, need to do
the following:
1) Check which driver is attached, so as to not detach the wrong driver
   (ie detaching usbfs while another instance of the app is using the device)
2) Detach the kernel driver
3) Claim the interface

Where moving from one step to the next for both 1-2 and 2-3 consists of
a (small) race window. So currently such apps are racy and people just live
with it.

This patch adds a new ioctl which makes it possible for apps to do this
in a race free manner. For flexibility apps can choose to:
1) Specify the driver to disconnect
2) Specify to disconnect any driver except for the one named by the app
3) Disconnect any driver

Note that if there is no driver attached, the ioctl will just act like the
regular claim-interface ioctl, this is by design, as returning an error for
this condition would open a new bag of race-conditions.

Changes in v2:
-Fix indentation of if blocks where the condition spans multiple lines
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fengguang Wu reported:
|drivers/usb/gadget/serial.c:89:22: sparse: cast truncates bits from
|constant value (24000000 becomes 0)

I obviously let the version number shift away. Since the version is a
16bit number it can be applied as it.

Cc: fengguang.wu@intel.com
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Currently mx23 fails to enumerate a USB device:

[ 1.300000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1.520000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1.740000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1.960000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 2.180000] hub 1-0:1.0: unable to enumerate USB device on port 1

Use a kernel workqueue to asynchronously delay the setting of
ENHOSTDISCONDETECT bit until after higher level hub connect/reset processing
is complete.  Prematurely setting the bit prevents the connection
processing from completing and not setting it prevents disconnect from being
detected. No delay is needed for clearing of ENHOSTDISCONDETECT.

Successfully tested on mx23-olinuxino (micro, mini and maxi variants) and mx28evk.

Cc: stable@vger.kernel.org # v3.6
Signed-off-by: NMike Thompson <mpthompson@gmail.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this will let us control PHYs on platforms which
need them.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.

For those which don't provide controllable transceivers
we will register nop transceivers.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.

For those which don't provide controllable transceivers
we will register nop transceivers.

Note that once OMAP's transceiver drivers reach mainline,
this glue layer will change accordingly.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.

For those which don't provide controllable transceivers
we will register nop transceivers.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The dereference should be moved below the NULL test.

spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Spotted by Fengguang Wu:
|In file included from drivers/usb/gadget/ether.c:110:0:
|drivers/usb/gadget/u_ether.c:87:21: error: expected ')' before 'uint'
|drivers/usb/gadget/u_ether.c:88:25: error: expected ')' before string constant

This is because u_ether.c relied on having module.h included somewhere.
This isn't the case since composite.c is no longer included.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The bcdDevice field is defined as
|Device release number in binary-coded decimal
in the USB 2.0 specification. We use this field to distinguish the UDCs
from each other. In theory this could be used on the host side to apply
certain quirks if the "special" UDC in combination with this gadget is
used. This hasn't been done as far as I am aware. In practice it would
be better to fix the UDC driver before shipping since a later release
might not need this quirk anymore.

There are some driver in tree (on the host side) which use the bcdDevice
field to figure out special workarounds for a given firmware revision.
This seems to make sense. Therefore this patch converts all gadgets
(except a few) to use the kernel version instead a random 2 or 3 plus
the UDC number. The few that don't report kernel's version are:
- webcam
  This one reports always a version 0x10 so allow it to do so in future.
- nokia
  This one reports always 0x211. The comment says that this gadget works
  only if the UDC supports altsettings so I added a check for this.
- serial
  This one reports 0x2400 + UDC number. Since the gadget version is 2.4
  this could make sense. Therefore bcdDevice is 0x2400 here.

I also remove various gadget_is_<name> macros which are unused. The
remaining few macros should be moved to feature / bug bitfield.
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Don't fail the initialization check for the platform_data
if there is avaiable an associated device tree node.
Signed-off-by: NFabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The dereference should be moved below the NULL test.

spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

MODULE_VERSION and AUTHOR looks better in composite.c than in
usbstrings.c so I move it there.
I put David Brownell as the module Author as I belive he wrote most of
it.
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This moves composite.c into libcomposite and updates all gadgets.
Finally!
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some gadgets provide custom entry here. Some may override it with an
etntry that is also created by composite if there was no value sumbitted
at all.
This patch removes all "custom manufacturer" strings which are the same
as these which are created by composite. Then it moves the creation of
the default manufacturer string to usb_composite_overwrite_options() in
case no command line argument has been used and the entry is still an
empty string.
By doing this we get rid of the global variable "composite_manufacturer"
in composite.
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>