#if defined(CONFIG_FOO) || defined(CONFIG_FOO_MODULE)

can be replaced by

#if IS_ENABLED(CONFIG_FOO)

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was picked up by sparse.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a driver for the FEC(MX6) that offers time
stamping and a PTP haderware clock. Because FEC\ENET(MX6)
hardware frequency adjustment is complex, we have implemented
this in software by changing the multiplication factor of the
timecounter.
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set GRP1 BIT21 ENET_CLK_SEL:
  Enet tx reference clk from internal clock from anatop
  (loopback through pad), this clock also sent out to external PHY
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ENET 1588 clock input pin
MX6Q_PAD_GPIO_16__ENET_ANATOP_ETHERNET_REF_OUT
and anatop PLL8 clock source for ENET
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A new file fec_ptp.c will use fec_enet_private to support 1588 PTP
move such structure to common header file fec.h
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch hooks into the CPTS code and adds support for the HWTSTAMP
ioctl. The patch includes code for the CPSW version found in the dm814x
even though the background device tree support for this board is still
missing.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a way to configure the CPTS input clock scaling factors
via the device tree.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because time stamping on both external ports of the switch simultaneously
is positively useless from the application's point of view, this patch
provides a DT configuration method to choose the active port.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a driver for the CPTS that offers time
stamping and a PTP hardware clock. Because some of the
CPTS hardware variants (like the am335x) do not support
frequency adjustment, we have implemented this in software
by changing the multiplication factor of the timecounter.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the cpsw driver to operate correctly with both the
dm814x and the am335x versions of the switch hardware.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch lets the CPSW driver remember the version number in order to
support the two different variants already in the wild.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code mixes up the CPSW_SS and the CPSW_WR register naming. This patch
changes the names to conform to the published Technical Reference Manual
from TI, in order to make working on the code less confusing.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding multicast address to ALE table via netdev ops to subscribe, transmit
or receive multicast frames to and from the network
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If no pinctrl available just report a warning as some architecture may not
need to do anything.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: adapt the error path, remove unneeded headers]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the ethernet frame payload word-aligned, possibly making the
memcpy into the skb a bit faster. This will be even more important
after we eliminate the copy altogether.

Also eliminate the redundant RX_OFFSET constant -- it has the same
definition and purpose as NET_IP_ALIGN.
Signed-off-by: NHavard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: adapt to newer kernel]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle all TX errors, not only underruns. TX error management is
deferred to a dedicated workqueue.
Reinitialize the TX ring after treating all remaining frames, and
restart the controller when everything has been cleaned up properly.
Napi is not stopped during this task as the driver only handles
napi for RX for now.
With this sequence, we do not need a special check during the xmit
method as the packets will be caught by TX disable during workqueue
execution.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add macb_get_regs() ethtool function and its helper function:
macb_get_regs_len().
The version field is deduced from the IP revision which gives the
"MACB or GEM" information. An additional version field is reserved.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of masking head and tail every time we increment them, just let them
wrap through UINT_MAX and mask them when subscripting. Add simple accessor
functions to do the subscripting properly to minimize the chances of messing
this up.

This makes the code slightly smaller, and hopefully faster as well.  Also,
doing the ring buffer management this way will simplify things a lot when
making the ring sizes configurable in the future.

Available number of descriptors in ring buffer function by David Laight.
Signed-off-by: NHavard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: split patch in topics, adapt to newer kernel]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some revision of GEM, TSR status register has more information.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function has little meaning so remove it altogether and
let ethtool core fill in the fields automatically.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert some noisy netdev_dbg() statements to netdev_vdbg(). Defining
DEBUG will no longer fill up the logs; VERBOSE_DEBUG still does.
Add one more verbose debug for ISR status.
Signed-off-by: NHavard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: split patch in topics, add ISR status]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove a couple of unneeded barriers and document the remaining ones.
Signed-off-by: NHavard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: split patch in topics]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add Gigabit Ethernet mode to GEM cadence IP and enable RGMII connection.
Signed-off-by: NPatrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the timecompare code from the kernel. The top five
reasons to do this are:

1. There are no more users of this code.
2. The original idea was a bit weak.
3. The original author has disappeared.
4. The code was not general purpose but tuned to a particular hardware,
5. There are better ways to accomplish clock synchronization.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Acked-by: NJohn Stultz <john.stultz@linaro.org>
Tested-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BF518 has a PTP time unit that works in a similar way to other MAC
based clocks, like gianfar, ixp46x, and igb. This patch adds support for
using the blackfin as a PHC. Although the blackfin hardware does offer a
few ancillary features, this patch implements only the basic operations.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces the sys time stamps and timecompare code with simple
raw hardware time stamps in nanosecond resolution. The only tricky bit is
to find a PTP Hardware Clock period slower than the input clock period
and a power of two.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware time stamping code is a compile time option for the blackfin.
When it is not enabled, the driver should fall back to the standard
ethtool reply to the get_ts_info query.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds an ioctl for PTP Hardware Clock (PHC) devices that allows
user space to measure the time offset between the PHC and the system
clock. Rather than hard coding any kind of estimation algorithm into the
kernel, this patch takes the more flexible approach of just delivering
an array of raw clock readings. In that way, the user space clock servo
may be adapted to new and different hardware clocks.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Acked-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Where a PTP clock driver is associated with a net or PHY driver, it
should be enabled automatically whenever that driver is enabled.
Therefore:

- Make PTP clock drivers select rather than depending on PTP_1588_CLOCK
- Remove separate boolean options for PTP clock drivers that are built
  as part of net driver modules.  (This also fixes cases where the PTP
  subsystem is wrongly forced to be built-in.)
- Set 'default y' for PTP clock drivers that depend on specific net
  drivers but are built separately
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PTP hardware clock drivers that select PTP_1588_CLOCK must currently
also select PPS.  For those drivers that don't, the user must enable
PPS, then enable PTP_1588_CLOCK, then the driver.  Simplify things for
developers and users by putting this selection in one place.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These are now established subsystems, and we want drivers to be able
to select PPS and PTP_1588_CLOCK without depending on EXPERIMENTAL.
Further, the use of EXPERIMENTAL is now deprecated in general.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.

There are two issues with getting filter back.

First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.

Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that

  reciprocal(user2_k) == reciprocal(user_k) == kernel_k

i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this

  user2_k = reciprocal(kernel_k)

with an exception, that if kernel_k == 0, then user2_k == 1.

The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.

changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements a simple multiqueue flow steering policy - tx follows rx
for tun/tap. The idea is simple, it just choose the txq based on which rxq it
comes. The flow were identified through the rxhash of a skb, and the hash to
queue mapping were recorded in a hlist with an ageing timer to retire the
mapping. The mapping were created when tun receives packet from userspace, and
was quired in .ndo_select_queue().

I run co-current TCP_CRR test and didn't see any mapping manipulation helpers in
perf top, so the overhead could be negelected.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sometimes usespace may need to active/deactive a queue, this could be done by
detaching and attaching a file from tuntap device.

This patch introduces a new ioctls - TUNSETQUEUE which could be used to do
this. Flag IFF_ATTACH_QUEUE were introduced to do attaching while
IFF_DETACH_QUEUE were introduced to do the detaching.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts tun/tap to a multiqueue devices and expose the multiqueue
queues as multiple file descriptors to userspace. Internally, each tun_file were
abstracted as a queue, and an array of pointers to tun_file structurs were
stored in tun_structure device, so multiple tun_files were allowed to be
attached to the device as multiple queues.

When choosing txq, we first try to identify a flow through its rxhash, if it
does not have such one, we could try recorded rxq and then use them to choose
the transmit queue. This policy may be changed in the future.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>