ata_eh_suspend() was returning 0 regardless of failure.  This bug has
potential to lose data on suspend.  Fix it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ap->id is logcial port ID which is unique among all ATA ports and
doesn't have anything to do with hardware port index.  ap->port_no is
the hardware port index and thus should be used when clearing IRQ mask
in ahci_thaw().

This problem has been spotted by Jeff Garzik <jgarzik@pobox.com>.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

On the Maple board, the AMD8111 IDE is in legacy mode... except that it
appears on IRQ 20 instead of IRQ 15. For drivers/ide this was handled by
the architecture's "pci_get_legacy_ide_irq()" function, but in libata we
just hard-code the numbers 14 and 15.

This patch provides asm-powerpc/libata-portmap.h which maps the IRQ as
appropriate, having added a pci_dev argument to the
ATA_{PRIM,SECOND}ARY_IRQ macros.

There's probably a better way to do this -- especially if we observe
that the _only_ case in which this seemingly-generic
"pci_get_legacy_ide_irq()" function returns anything other than 14 and
15 for primary and secondary respectively is the case of the AMD8111 on
the Maple board -- couldn't we handle that with a special case in the
pata_amd driver, or perhaps with a PCI quirk for Maple to switch it into
native mode during early boot and assign resources properly?
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Before hardreset, ahci initialized stat part of received FIS area to
0xff to wait for the first D2H Reg FIS which would change the value to
device ready state.  This used to work but now libata considers status
value of 0xff as device not present making this wait prone to failure.

This patch makes ahci use 0x80 for the wait stat value instead of
0xff to fix the above problem.
Signed-off-by: NTejun Heo <htejun@gmail.com>

 drivers/ata/ahci.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Call ata_bmdma_irq_clear() directly instead of through
ap->ops->irq_clear() according to libata style guideline.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix endianness in spurious interrupt message.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fixes bogus accesses to ports 0-15 with a non DMA capable controller.
This I think should go in for 2.6.20
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Some uli controllers have stuck SIMPLEX bit which can't be cleared
with ata_pci_clear_simplex(), but the controller is capable of doing
DMAs on both channels simultaneously.  Implement ATA_FLAG_IGN_SIMPLEX
which makes libata ignore the simplex bit and use it in sata_uli.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

We're still seeing a lot of issues with NCQ implementation in drive
firmwares.  Sprious FISes during NCQ command phase occur on many
drives and some of them seem potentially dangerous (at least to me).
Until we find the solution, spurious messages can give us more info.
Improve and limit them such that more info can be reported while not
disturbing users too much.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

vt6420 completely loses its ability to raise IRQ for ATAPI devices if
ATA_NIEN is diddled with in ->freeze.  Further investigation is
necessary to determine whether this problem is shared on other
controllers but it doesn't seem to be at this point.

Make vt6420's ->freeze only clear IRQ to fix this problem.  This makes
vt6420 relatively more prone to IRQ storms but the controller is way
too braindamaged to worry about that anyway.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When set_mode() changed ->set_mode didn't adapt. This makes the needed
changes and removes the relevant FIXME case.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Rather than ending up with two layers of negation jut rename the variable
and lose one.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fixup the inialization of qc->n_elem. It currently gets
initialized to 1 for commands that do not transfer any data.
Fix this by initializing n_elem to 0 and only setting to 1
in ata_scsi_qc_new when there is data to transfer. This fixes
some problems seen with SATA devices attached to ipr adapters.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Some ATA/ATAPI devices act weirdly after the link is put into slumber
mode.  Some hang completely requiring physical power removal while
others fail to wake up till the link is hardreset a couple of times.

The addition of slumber on power down was never driven by real need.
It just followed what ahci spec said literally.  The spec itself seems
faulty in that it doesn't consider devices (not controllers) which
don't support link powersaving mode.

Theory never matches reality when it comes to dark allys of cheap
ATA/ATAPI world.  It's just unrealistic to expect vendors to test
rarely used link powersaving feature rigorously.  This patch makes
ahci more friendly to the coldness of reality.

This shouldn't have any negative effect - when suspend operation
succeeds, we power off the whole machine; otherwise, we wake up
everything.  I can't see any reason to be so elaborate with powering
down the link in the first place.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Several people reported issues with certain drive commands timing out on
sata_nv controllers running in ADMA mode. The commands in question were
non-DMA-mapped commands, usually FLUSH CACHE or FLUSH CACHE EXT.

 From experimentation it appears that the NV_INT_DEV indication isn't
always set when a legitimate command completion interrupt is received on
a legacy-mode command, at least not on these controllers in ADMA mode.
When a command is pending on the port, force the flag on always in the
irq_stat value before calling nv_host_intr so that the drive busy state
is always checked by ata_host_intr.

This also fixes some questionable code in nv_host_intr which called
ata_check_status when a command was pending and ata_host_intr returned
"unhandled". If the device interrupted at just the wrong time this could
cause interrupts to be lost.
Signed-off-by: NRobert Hancock <hancockr@shaw.ca>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

As with JMicron controllers, ULi M5288 sets interface fatal error bit
on device error including ATAPI CC.  This makes libata hardreset the
port on ATAPI CC thus making it impossible to use.  Ignore interface
fatal error bit on ULi M5288.  This fixes bugzilla bug #7837.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

With the following patch, my HighPoint 2310 with a Marvell 88SX7042 on
it seems to work OK.

The controller only has 4 ports, with MV_FLAG_DUAL_HC it seems to init 8
ports and fails miserably at probe time. There are no other devices mapped
to that chip, maybe it was just incorrectly specified in the first place?
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

libata EH ignores port-wide actions in per-dev action mask.  However,
device resume requests EH_SOFTRESET using per-dev action mask.  Under
certain circumstances, this results in not resetting frozen port after
resuming which causes failure of all commands.

This patch allows port-wide actions to be requested in per-dev action
mask.  Before EH recovery starts, port-wide actions will be collected.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add PCI ID 0x5337 to supported PCI ID.  This is VT8237 in IDE mode.
Signed-off-by: NLuca Pedrielli <luca.pedrielli@barradev.it>
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The HPT37x driver very carefully handles DMA completions and the needed
fixups are done on pci registers 0x50 and 0x52.  This is unfortunate
because the actual registers are 0x50 and 0x54.  Fixing this offset cures
the second channel problems reported.

Secondly there are some problems with the HPT370 and certain ATA drives.
The filter code however only filters ATAPI devices due to a reversed type
check.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NAlan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is a slight variant on the patch I posted December 16th to fix
libata combined mode handling. The only real change is that we now
correctly also reserve BAR1,2,4. That is basically a neatness issue.

Jeff was unhappy about two things

1. That it didn't work in the case of one channel native one channel
legacy.

This is a silly complaint because the SFF layer in libata doesn't handle
this case yet anyway.

2. The case where combined mode is in use and IDE=n.

In this case the libata quirk code reserves the resources in question
correctly already.

Once the combined mode stuff is redone properly (2.6.21) then the entire
mess turns into a single pci_request_regions() for all cases and all the
ugly resource hackery goes away.

I'm sending this now rather than after running full test suites so that
it can get the maximal testing in a short time. I'll be running tests on
this after lunch.
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Acked-by: NAlessandro Suardi <alessandro.suardi@gmail.com>
Acked-by: NTheodore Tso <tytso@mit.edu>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Now that iomap merge is close to reality, and since the warnings and
issue have been around so long, we don't need a reminder on every build
that libata needs to be converted over to iomap.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

libata depended on SCSI command to have the correct length when
tranlating it into an ATA command.  This generally worked for commands
issued by SCSI HLD but user could issue arbitrary broken command using
sg interface.

Also, when building ATAPI command, full command size was always
copied.  Because some ATAPI devices needs bytes after CDB cleared, if
upper layer doesn't clear bytes after CDB, such devices will
malfunction.  This necessiated recent clear-garbage-after-CDB fix in
sg interfaces.  However, scsi_execute() isn't fixed yet and HL-DT-ST
DVD-RAM GSA-H30N malfunctions on initialization commands issued from
SCSI.

This patch makes xlat functions always consider SCSI cmd_len.  Each
translation function checks for proper cmd_len and ATAPI translaation
clears bytes after CDB.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Douglas Gilbert <dougg@torque.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

xlat function will be updated to consider qc->scsicmd->cmd_len and
many xlat functions deference qc->scsicmd already.  It doesn't make
sense to pass qc->scsicmd->cmnd as @cdb separately.  Kill the
argument.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Variable names in xlat functions are quite confusing now.  'scsicmd'
is used for CDB while qc->scsicmd points to struct scsi_cmnd while
'cmd' is used for struct scsi_cmnd.

This patch cleans up variable names in xlat functions such that 'scmd'
is used for struct scsi_cmnd and 'cdb' for CDB.  Also, 'scmd' local
variable is added if qc->scsicmd is used multiple times.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The content of memory map io of BAR5 have been change from MCP65 then
sata_nv can't work fine on the platform based on MCP65 and MCP67, so move
their IDs from sata_nv.c to ahci.c.
Signed-off-by: NPeer Chen <pchen@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make this array static so it doesn't have to be built at runtime.

Cc: Alan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

side-effectful-expression-within-assert give me the creeps.

Cc: Alan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The UDMA66 VIA hardware has no controller side cable detect bits we can
use. This patch minimally fixes the problem by reporting unknown in this
case and using drive side detection.

The old drivers/ide code does some additional tricks but those aren't
appropriate now we are in -rc.

Without this update UDMA66 via controllers run slowly. They don't fail so
it's a borderline call whether this is -rc material or not.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

> Thanks for clarifying Bill, and sorry Alan. ata_piix does indeed work
> correctly. The help text is a bit confusing:
>
> config ATA_PIIX
>         tristate "Intel PIIX/ICH SATA support"
>         depends on PCI
>         help
>           This option enables support for ICH5/6/7/8 Serial ATA.
>           If PATA support was enabled previously, this enables
>           support for select Intel PIIX/ICH PATA host controllers.

New help text
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This removes the extra definition of the .error_handler member
in the pata_rz1000 driver.
Signed-off-by: NIra W. Snyder <kernel@irasnyder.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The return value of platform_device_register_simple() should be checked
by IS_ERR().

Cc: Jeff Garzik <jgarzik@pobox.com>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Do not mangle with HOST_CAP while resetting controller.  The code is
there for a historical reason.  The mangling breaks controller feature
detection and 0 PORTS_IMPL workaround code.

This problem was spotted by Manoj Kasichainula.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Manoj Kasichainula <manoj@io.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Calling sg_init_one() with NULL buf causes oops on certain
configurations.  Don't initialize sg in ata_exec_internal() if
DMA_NONE and make the function complain if @buf is NULL when dma_dir
isn't DMA_NONE.  While at it, fix comment.

The problem is discovered and initial patch was submitted by Arnd
Bergmann.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Current Broadcom/Serverworks SATA boards (including Apple K2 SATA)
have problems with ATAPI DMA, so it is disabled.  ATAPI PIO, ATA PIO,
and ATA DMA continue to work just fine.
Acked-by: NAnantha Subramanyam <ananth@broadcom.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

We are inside spin_lock_irqsave().  quoth akpm's debug facility:

 [  231.948000] SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
 [  232.232000] ata1.00: configured for UDMA/33
 [  232.404000] WARNING (1) at arch/i386/mm/highmem.c:47 kmap_atomic()
 [  232.404000]  [<c01162e6>] kmap_atomic+0xa9/0x1ab
 [  232.404000]  [<c0242c81>] ata_scsi_rbuf_get+0x1c/0x30
 [  232.404000]  [<c0242caf>] ata_scsi_rbuf_fill+0x1a/0x87
 [  232.404000]  [<c0243ab2>] ata_scsiop_mode_sense+0x0/0x309
 [  232.404000]  [<c01729d5>] end_bio_bh_io_sync+0x0/0x37
 [  232.404000]  [<c02311c6>] scsi_done+0x0/0x16
 [  232.404000]  [<c02311c6>] scsi_done+0x0/0x16
 [  232.404000]  [<c0242dcc>] ata_scsi_simulate+0xb0/0x13f
[...]
Signed-off-by: NJeff Garzik <jeff@garzik.org>

piix_init_one() allocates host private data which should be freed by
piix_host_stop().  ich_pata_ops wasn't converted to piix_host_stop()
while merging, leaking 4 bytes on driver detach.  Fix it.

This was spotted using Kmemleak by Catalin Marinas.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Catalin Marinas <catalin.marinas@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This updated patch adds the Intel ICH9 IDE mode SATA controller DID's.
Signed-off-by: NJason Gaston <jason.d.gaston@intel.com>
Acked-by: NTejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>