soc: xilinx: xlnx_vcu: Add Xilinx ZYNQMP VCU logicoreIP init driver

Xilinx ZYNQMP logicoreIP Init driver is based on the new
LogiCoreIP design created. This driver provides the processing system
and programmable logic isolation. Set the frequency based on the clock
information get from the logicoreIP register set.
Signed-off-by: NDhaval Shah <dshah@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

drivers/soc/xilinx/Kconfig

 # SPDX-License-Identifier: GPL-2.0
 menu "Xilinx SoC drivers"
 
+config XILINX_VCU
+        tristate "Xilinx VCU logicoreIP Init"
+        help
+          Provides the driver to enable and disable the isolation between the
+          processing system and programmable logic part by using the logicoreIP
+          register set. This driver also configures the frequency based on the
+          clock information from the logicoreIP register set.
+
+          If you say yes here you get support for the logicoreIP.
+
+          If unsure, say N.
+
+          To compile this driver as a module, choose M here: the
+          module will be called xlnx_vcu.
+
 endmenu

drivers/soc/xilinx/Makefile

 # SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_XILINX_VCU)	+= xlnx_vcu.o

drivers/soc/xilinx/xlnx_vcu.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx VCU Init
+ *
+ * Copyright (C) 2016 - 2017 Xilinx, Inc.
+ *
+ * Contacts   Dhaval Shah <dshah@xilinx.com>
+ */
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+/* Address map for different registers implemented in the VCU LogiCORE IP. */
+#define VCU_ECODER_ENABLE		0x00
+#define VCU_DECODER_ENABLE		0x04
+#define VCU_MEMORY_DEPTH		0x08
+#define VCU_ENC_COLOR_DEPTH		0x0c
+#define VCU_ENC_VERTICAL_RANGE		0x10
+#define VCU_ENC_FRAME_SIZE_X		0x14
+#define VCU_ENC_FRAME_SIZE_Y		0x18
+#define VCU_ENC_COLOR_FORMAT		0x1c
+#define VCU_ENC_FPS			0x20
+#define VCU_MCU_CLK			0x24
+#define VCU_CORE_CLK			0x28
+#define VCU_PLL_BYPASS			0x2c
+#define VCU_ENC_CLK			0x30
+#define VCU_PLL_CLK			0x34
+#define VCU_ENC_VIDEO_STANDARD		0x38
+#define VCU_STATUS			0x3c
+#define VCU_AXI_ENC_CLK			0x40
+#define VCU_AXI_DEC_CLK			0x44
+#define VCU_AXI_MCU_CLK			0x48
+#define VCU_DEC_VIDEO_STANDARD		0x4c
+#define VCU_DEC_FRAME_SIZE_X		0x50
+#define VCU_DEC_FRAME_SIZE_Y		0x54
+#define VCU_DEC_FPS			0x58
+#define VCU_BUFFER_B_FRAME		0x5c
+#define VCU_WPP_EN			0x60
+#define VCU_PLL_CLK_DEC			0x64
+#define VCU_GASKET_INIT			0x74
+#define VCU_GASKET_VALUE		0x03
+
+/* vcu slcr registers, bitmask and shift */
+#define VCU_PLL_CTRL			0x24
+#define VCU_PLL_CTRL_RESET_MASK		0x01
+#define VCU_PLL_CTRL_RESET_SHIFT	0
+#define VCU_PLL_CTRL_BYPASS_MASK	0x01
+#define VCU_PLL_CTRL_BYPASS_SHIFT	3
+#define VCU_PLL_CTRL_FBDIV_MASK		0x7f
+#define VCU_PLL_CTRL_FBDIV_SHIFT	8
+#define VCU_PLL_CTRL_POR_IN_MASK	0x01
+#define VCU_PLL_CTRL_POR_IN_SHIFT	1
+#define VCU_PLL_CTRL_PWR_POR_MASK	0x01
+#define VCU_PLL_CTRL_PWR_POR_SHIFT	2
+#define VCU_PLL_CTRL_CLKOUTDIV_MASK	0x03
+#define VCU_PLL_CTRL_CLKOUTDIV_SHIFT	16
+#define VCU_PLL_CTRL_DEFAULT		0
+#define VCU_PLL_DIV2			2
+
+#define VCU_PLL_CFG			0x28
+#define VCU_PLL_CFG_RES_MASK		0x0f
+#define VCU_PLL_CFG_RES_SHIFT		0
+#define VCU_PLL_CFG_CP_MASK		0x0f
+#define VCU_PLL_CFG_CP_SHIFT		5
+#define VCU_PLL_CFG_LFHF_MASK		0x03
+#define VCU_PLL_CFG_LFHF_SHIFT		10
+#define VCU_PLL_CFG_LOCK_CNT_MASK	0x03ff
+#define VCU_PLL_CFG_LOCK_CNT_SHIFT	13
+#define VCU_PLL_CFG_LOCK_DLY_MASK	0x7f
+#define VCU_PLL_CFG_LOCK_DLY_SHIFT	25
+#define VCU_ENC_CORE_CTRL		0x30
+#define VCU_ENC_MCU_CTRL		0x34
+#define VCU_DEC_CORE_CTRL		0x38
+#define VCU_DEC_MCU_CTRL		0x3c
+#define VCU_PLL_DIVISOR_MASK		0x3f
+#define VCU_PLL_DIVISOR_SHIFT		4
+#define VCU_SRCSEL_MASK			0x01
+#define VCU_SRCSEL_SHIFT		0
+#define VCU_SRCSEL_PLL			1
+
+#define VCU_PLL_STATUS			0x60
+#define VCU_PLL_STATUS_LOCK_STATUS_MASK	0x01
+
+#define MHZ				1000000
+#define FVCO_MIN			(1500U * MHZ)
+#define FVCO_MAX			(3000U * MHZ)
+#define DIVISOR_MIN			0
+#define DIVISOR_MAX			63
+#define FRAC				100
+#define LIMIT				(10 * MHZ)
+
+/**
+ * struct xvcu_device - Xilinx VCU init device structure
+ * @dev: Platform device
+ * @pll_ref: pll ref clock source
+ * @aclk: axi clock source
+ * @logicore_reg_ba: logicore reg base address
+ * @vcu_slcr_ba: vcu_slcr Register base address
+ * @coreclk: core clock frequency
+ */
+struct xvcu_device {
+	struct device *dev;
+	struct clk *pll_ref;
+	struct clk *aclk;
+	void __iomem *logicore_reg_ba;
+	void __iomem *vcu_slcr_ba;
+	u32 coreclk;
+};
+
+/**
+ * struct xvcu_pll_cfg - Helper data
+ * @fbdiv: The integer portion of the feedback divider to the PLL
+ * @cp: PLL charge pump control
+ * @res: PLL loop filter resistor control
+ * @lfhf: PLL loop filter high frequency capacitor control
+ * @lock_dly: Lock circuit configuration settings for lock windowsize
+ * @lock_cnt: Lock circuit counter setting
+ */
+struct xvcu_pll_cfg {
+	u32 fbdiv;
+	u32 cp;
+	u32 res;
+	u32 lfhf;
+	u32 lock_dly;
+	u32 lock_cnt;
+};
+
+static const struct xvcu_pll_cfg xvcu_pll_cfg[] = {
+	{ 25, 3, 10, 3, 63, 1000 },
+	{ 26, 3, 10, 3, 63, 1000 },
+	{ 27, 4, 6, 3, 63, 1000 },
+	{ 28, 4, 6, 3, 63, 1000 },
+	{ 29, 4, 6, 3, 63, 1000 },
+	{ 30, 4, 6, 3, 63, 1000 },
+	{ 31, 6, 1, 3, 63, 1000 },
+	{ 32, 6, 1, 3, 63, 1000 },
+	{ 33, 4, 10, 3, 63, 1000 },
+	{ 34, 5, 6, 3, 63, 1000 },
+	{ 35, 5, 6, 3, 63, 1000 },
+	{ 36, 5, 6, 3, 63, 1000 },
+	{ 37, 5, 6, 3, 63, 1000 },
+	{ 38, 5, 6, 3, 63, 975 },
+	{ 39, 3, 12, 3, 63, 950 },
+	{ 40, 3, 12, 3, 63, 925 },
+	{ 41, 3, 12, 3, 63, 900 },
+	{ 42, 3, 12, 3, 63, 875 },
+	{ 43, 3, 12, 3, 63, 850 },
+	{ 44, 3, 12, 3, 63, 850 },
+	{ 45, 3, 12, 3, 63, 825 },
+	{ 46, 3, 12, 3, 63, 800 },
+	{ 47, 3, 12, 3, 63, 775 },
+	{ 48, 3, 12, 3, 63, 775 },
+	{ 49, 3, 12, 3, 63, 750 },
+	{ 50, 3, 12, 3, 63, 750 },
+	{ 51, 3, 2, 3, 63, 725 },
+	{ 52, 3, 2, 3, 63, 700 },
+	{ 53, 3, 2, 3, 63, 700 },
+	{ 54, 3, 2, 3, 63, 675 },
+	{ 55, 3, 2, 3, 63, 675 },
+	{ 56, 3, 2, 3, 63, 650 },
+	{ 57, 3, 2, 3, 63, 650 },
+	{ 58, 3, 2, 3, 63, 625 },
+	{ 59, 3, 2, 3, 63, 625 },
+	{ 60, 3, 2, 3, 63, 625 },
+	{ 61, 3, 2, 3, 63, 600 },
+	{ 62, 3, 2, 3, 63, 600 },
+	{ 63, 3, 2, 3, 63, 600 },
+	{ 64, 3, 2, 3, 63, 600 },
+	{ 65, 3, 2, 3, 63, 600 },
+	{ 66, 3, 2, 3, 63, 600 },
+	{ 67, 3, 2, 3, 63, 600 },
+	{ 68, 3, 2, 3, 63, 600 },
+	{ 69, 3, 2, 3, 63, 600 },
+	{ 70, 3, 2, 3, 63, 600 },
+	{ 71, 3, 2, 3, 63, 600 },
+	{ 72, 3, 2, 3, 63, 600 },
+	{ 73, 3, 2, 3, 63, 600 },
+	{ 74, 3, 2, 3, 63, 600 },
+	{ 75, 3, 2, 3, 63, 600 },
+	{ 76, 3, 2, 3, 63, 600 },
+	{ 77, 3, 2, 3, 63, 600 },
+	{ 78, 3, 2, 3, 63, 600 },
+	{ 79, 3, 2, 3, 63, 600 },
+	{ 80, 3, 2, 3, 63, 600 },
+	{ 81, 3, 2, 3, 63, 600 },
+	{ 82, 3, 2, 3, 63, 600 },
+	{ 83, 4, 2, 3, 63, 600 },
+	{ 84, 4, 2, 3, 63, 600 },
+	{ 85, 4, 2, 3, 63, 600 },
+	{ 86, 4, 2, 3, 63, 600 },
+	{ 87, 4, 2, 3, 63, 600 },
+	{ 88, 4, 2, 3, 63, 600 },
+	{ 89, 4, 2, 3, 63, 600 },
+	{ 90, 4, 2, 3, 63, 600 },
+	{ 91, 4, 2, 3, 63, 600 },
+	{ 92, 4, 2, 3, 63, 600 },
+	{ 93, 4, 2, 3, 63, 600 },
+	{ 94, 4, 2, 3, 63, 600 },
+	{ 95, 4, 2, 3, 63, 600 },
+	{ 96, 4, 2, 3, 63, 600 },
+	{ 97, 4, 2, 3, 63, 600 },
+	{ 98, 4, 2, 3, 63, 600 },
+	{ 99, 4, 2, 3, 63, 600 },
+	{ 100, 4, 2, 3, 63, 600 },
+	{ 101, 4, 2, 3, 63, 600 },
+	{ 102, 4, 2, 3, 63, 600 },
+	{ 103, 5, 2, 3, 63, 600 },
+	{ 104, 5, 2, 3, 63, 600 },
+	{ 105, 5, 2, 3, 63, 600 },
+	{ 106, 5, 2, 3, 63, 600 },
+	{ 107, 3, 4, 3, 63, 600 },
+	{ 108, 3, 4, 3, 63, 600 },
+	{ 109, 3, 4, 3, 63, 600 },
+	{ 110, 3, 4, 3, 63, 600 },
+	{ 111, 3, 4, 3, 63, 600 },
+	{ 112, 3, 4, 3, 63, 600 },
+	{ 113, 3, 4, 3, 63, 600 },
+	{ 114, 3, 4, 3, 63, 600 },
+	{ 115, 3, 4, 3, 63, 600 },
+	{ 116, 3, 4, 3, 63, 600 },
+	{ 117, 3, 4, 3, 63, 600 },
+	{ 118, 3, 4, 3, 63, 600 },
+	{ 119, 3, 4, 3, 63, 600 },
+	{ 120, 3, 4, 3, 63, 600 },
+	{ 121, 3, 4, 3, 63, 600 },
+	{ 122, 3, 4, 3, 63, 600 },
+	{ 123, 3, 4, 3, 63, 600 },
+	{ 124, 3, 4, 3, 63, 600 },
+	{ 125, 3, 4, 3, 63, 600 },
+};
+
+/**
+ * xvcu_read - Read from the VCU register space
+ * @iomem:	vcu reg space base address
+ * @offset:	vcu reg offset from base
+ *
+ * Return:	Returns 32bit value from VCU register specified
+ *
+ */
+static inline u32 xvcu_read(void __iomem *iomem, u32 offset)
+{
+	return ioread32(iomem + offset);
+}
+
+/**
+ * xvcu_write - Write to the VCU register space
+ * @iomem:	vcu reg space base address
+ * @offset:	vcu reg offset from base
+ * @value:	Value to write
+ */
+static inline void xvcu_write(void __iomem *iomem, u32 offset, u32 value)
+{
+	iowrite32(value, iomem + offset);
+}
+
+/**
+ * xvcu_write_field_reg - Write to the vcu reg field
+ * @iomem:	vcu reg space base address
+ * @offset:	vcu reg offset from base
+ * @field:	vcu reg field to write to
+ * @mask:	vcu reg mask
+ * @shift:	vcu reg number of bits to shift the bitfield
+ */
+static void xvcu_write_field_reg(void __iomem *iomem, int offset,
+				 u32 field, u32 mask, int shift)
+{
+	u32 val = xvcu_read(iomem, offset);
+
+	val &= ~(mask << shift);
+	val |= (field & mask) << shift;
+
+	xvcu_write(iomem, offset, val);
+}
+
+/**
+ * xvcu_set_vcu_pll_info - Set the VCU PLL info
+ * @xvcu:	Pointer to the xvcu_device structure
+ *
+ * Programming the VCU PLL based on the user configuration
+ * (ref clock freq, core clock freq, mcu clock freq).
+ * Core clock frequency has higher priority than mcu clock frequency
+ * Errors in following cases
+ *    - When mcu or clock clock get from logicoreIP is 0
+ *    - When VCU PLL DIV related bits value other than 1
+ *    - When proper data not found for given data
+ *    - When sis570_1 clocksource related operation failed
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+static int xvcu_set_vcu_pll_info(struct xvcu_device *xvcu)
+{
+	u32 refclk, coreclk, mcuclk, inte, deci;
+	u32 divisor_mcu, divisor_core, fvco;
+	u32 clkoutdiv, vcu_pll_ctrl, pll_clk;
+	u32 cfg_val, mod, ctrl;
+	int ret, i;
+	const struct xvcu_pll_cfg *found = NULL;
+
+	inte = xvcu_read(xvcu->logicore_reg_ba, VCU_PLL_CLK);
+	deci = xvcu_read(xvcu->logicore_reg_ba, VCU_PLL_CLK_DEC);
+	coreclk = xvcu_read(xvcu->logicore_reg_ba, VCU_CORE_CLK) * MHZ;
+	mcuclk = xvcu_read(xvcu->logicore_reg_ba, VCU_MCU_CLK) * MHZ;
+	if (!mcuclk || !coreclk) {
+		dev_err(xvcu->dev, "Invalid mcu and core clock data\n");
+		return -EINVAL;
+	}
+
+	refclk = (inte * MHZ) + (deci * (MHZ / FRAC));
+	dev_dbg(xvcu->dev, "Ref clock from logicoreIP is %uHz\n", refclk);
+	dev_dbg(xvcu->dev, "Core clock from logicoreIP is %uHz\n", coreclk);
+	dev_dbg(xvcu->dev, "Mcu clock from logicoreIP is %uHz\n", mcuclk);
+
+	clk_disable_unprepare(xvcu->pll_ref);
+	ret = clk_set_rate(xvcu->pll_ref, refclk);
+	if (ret)
+		dev_warn(xvcu->dev, "failed to set logicoreIP refclk rate\n");
+
+	ret = clk_prepare_enable(xvcu->pll_ref);
+	if (ret) {
+		dev_err(xvcu->dev, "failed to enable pll_ref clock source\n");
+		return ret;
+	}
+
+	refclk = clk_get_rate(xvcu->pll_ref);
+
+	/*
+	 * The divide-by-2 should be always enabled (==1)
+	 * to meet the timing in the design.
+	 * Otherwise, it's an error
+	 */
+	vcu_pll_ctrl = xvcu_read(xvcu->vcu_slcr_ba, VCU_PLL_CTRL);
+	clkoutdiv = vcu_pll_ctrl >> VCU_PLL_CTRL_CLKOUTDIV_SHIFT;
+	clkoutdiv = clkoutdiv && VCU_PLL_CTRL_CLKOUTDIV_MASK;
+	if (clkoutdiv != 1) {
+		dev_err(xvcu->dev, "clkoutdiv value is invalid\n");
+		return -EINVAL;
+	}
+
+	for (i = ARRAY_SIZE(xvcu_pll_cfg) - 1; i >= 0; i--) {
+		const struct xvcu_pll_cfg *cfg = &xvcu_pll_cfg[i];
+
+		fvco = cfg->fbdiv * refclk;
+		if (fvco >= FVCO_MIN && fvco <= FVCO_MAX) {
+			pll_clk = fvco / VCU_PLL_DIV2;
+			if (fvco % VCU_PLL_DIV2 != 0)
+				pll_clk++;
+			mod = pll_clk % coreclk;
+			if (mod < LIMIT) {
+				divisor_core = pll_clk / coreclk;
+			} else if (coreclk - mod < LIMIT) {
+				divisor_core = pll_clk / coreclk;
+				divisor_core++;
+			} else {
+				continue;
+			}
+			if (divisor_core >= DIVISOR_MIN &&
+			    divisor_core <= DIVISOR_MAX) {
+				found = cfg;
+				divisor_mcu = pll_clk / mcuclk;
+				mod = pll_clk % mcuclk;
+				if (mcuclk - mod < LIMIT)
+					divisor_mcu++;
+				break;
+			}
+		}
+	}
+
+	if (!found) {
+		dev_err(xvcu->dev, "Invalid clock combination.\n");
+		return -EINVAL;
+	}
+
+	xvcu->coreclk = pll_clk / divisor_core;
+	mcuclk = pll_clk / divisor_mcu;
+	dev_dbg(xvcu->dev, "Actual Ref clock freq is %uHz\n", refclk);
+	dev_dbg(xvcu->dev, "Actual Core clock freq is %uHz\n", xvcu->coreclk);
+	dev_dbg(xvcu->dev, "Actual Mcu clock freq is %uHz\n", mcuclk);
+
+	vcu_pll_ctrl &= ~(VCU_PLL_CTRL_FBDIV_MASK << VCU_PLL_CTRL_FBDIV_SHIFT);
+	vcu_pll_ctrl |= (found->fbdiv & VCU_PLL_CTRL_FBDIV_MASK) <<
+			 VCU_PLL_CTRL_FBDIV_SHIFT;
+	vcu_pll_ctrl &= ~(VCU_PLL_CTRL_POR_IN_MASK <<
+			  VCU_PLL_CTRL_POR_IN_SHIFT);
+	vcu_pll_ctrl |= (VCU_PLL_CTRL_DEFAULT & VCU_PLL_CTRL_POR_IN_MASK) <<
+			 VCU_PLL_CTRL_POR_IN_SHIFT;
+	vcu_pll_ctrl &= ~(VCU_PLL_CTRL_PWR_POR_MASK <<
+			  VCU_PLL_CTRL_PWR_POR_SHIFT);
+	vcu_pll_ctrl |= (VCU_PLL_CTRL_DEFAULT & VCU_PLL_CTRL_PWR_POR_MASK) <<
+			 VCU_PLL_CTRL_PWR_POR_SHIFT;
+	xvcu_write(xvcu->vcu_slcr_ba, VCU_PLL_CTRL, vcu_pll_ctrl);
+
+	/* Set divisor for the core and mcu clock */
+	ctrl = xvcu_read(xvcu->vcu_slcr_ba, VCU_ENC_CORE_CTRL);
+	ctrl &= ~(VCU_PLL_DIVISOR_MASK << VCU_PLL_DIVISOR_SHIFT);
+	ctrl |= (divisor_core & VCU_PLL_DIVISOR_MASK) <<
+		 VCU_PLL_DIVISOR_SHIFT;
+	ctrl &= ~(VCU_SRCSEL_MASK << VCU_SRCSEL_SHIFT);
+	ctrl |= (VCU_SRCSEL_PLL & VCU_SRCSEL_MASK) << VCU_SRCSEL_SHIFT;
+	xvcu_write(xvcu->vcu_slcr_ba, VCU_ENC_CORE_CTRL, ctrl);
+
+	ctrl = xvcu_read(xvcu->vcu_slcr_ba, VCU_DEC_CORE_CTRL);
+	ctrl &= ~(VCU_PLL_DIVISOR_MASK << VCU_PLL_DIVISOR_SHIFT);
+	ctrl |= (divisor_core & VCU_PLL_DIVISOR_MASK) <<
+		 VCU_PLL_DIVISOR_SHIFT;
+	ctrl &= ~(VCU_SRCSEL_MASK << VCU_SRCSEL_SHIFT);
+	ctrl |= (VCU_SRCSEL_PLL & VCU_SRCSEL_MASK) << VCU_SRCSEL_SHIFT;
+	xvcu_write(xvcu->vcu_slcr_ba, VCU_DEC_CORE_CTRL, ctrl);
+
+	ctrl = xvcu_read(xvcu->vcu_slcr_ba, VCU_ENC_MCU_CTRL);
+	ctrl &= ~(VCU_PLL_DIVISOR_MASK << VCU_PLL_DIVISOR_SHIFT);
+	ctrl |= (divisor_mcu & VCU_PLL_DIVISOR_MASK) << VCU_PLL_DIVISOR_SHIFT;
+	ctrl &= ~(VCU_SRCSEL_MASK << VCU_SRCSEL_SHIFT);
+	ctrl |= (VCU_SRCSEL_PLL & VCU_SRCSEL_MASK) << VCU_SRCSEL_SHIFT;
+	xvcu_write(xvcu->vcu_slcr_ba, VCU_ENC_MCU_CTRL, ctrl);
+
+	ctrl = xvcu_read(xvcu->vcu_slcr_ba, VCU_DEC_MCU_CTRL);
+	ctrl &= ~(VCU_PLL_DIVISOR_MASK << VCU_PLL_DIVISOR_SHIFT);
+	ctrl |= (divisor_mcu & VCU_PLL_DIVISOR_MASK) << VCU_PLL_DIVISOR_SHIFT;
+	ctrl &= ~(VCU_SRCSEL_MASK << VCU_SRCSEL_SHIFT);
+	ctrl |= (VCU_SRCSEL_PLL & VCU_SRCSEL_MASK) << VCU_SRCSEL_SHIFT;
+	xvcu_write(xvcu->vcu_slcr_ba, VCU_DEC_MCU_CTRL, ctrl);
+
+	/* Set RES, CP, LFHF, LOCK_CNT and LOCK_DLY cfg values */
+	cfg_val = (found->res << VCU_PLL_CFG_RES_SHIFT) |
+		   (found->cp << VCU_PLL_CFG_CP_SHIFT) |
+		   (found->lfhf << VCU_PLL_CFG_LFHF_SHIFT) |
+		   (found->lock_cnt << VCU_PLL_CFG_LOCK_CNT_SHIFT) |
+		   (found->lock_dly << VCU_PLL_CFG_LOCK_DLY_SHIFT);
+	xvcu_write(xvcu->vcu_slcr_ba, VCU_PLL_CFG, cfg_val);
+
+	return 0;
+}
+
+/**
+ * xvcu_set_pll - PLL init sequence
+ * @xvcu:	Pointer to the xvcu_device structure
+ *
+ * Call the api to set the PLL info and once that is done then
+ * init the PLL sequence to make the PLL stable.
+ *
+ * Return:	Returns status, either success or error+reason
+ */
+static int xvcu_set_pll(struct xvcu_device *xvcu)
+{
+	u32 lock_status;
+	unsigned long timeout;
+	int ret;
+
+	ret = xvcu_set_vcu_pll_info(xvcu);
+	if (ret) {
+		dev_err(xvcu->dev, "failed to set pll info\n");
+		return ret;
+	}
+
+	xvcu_write_field_reg(xvcu->vcu_slcr_ba, VCU_PLL_CTRL,
+			     1, VCU_PLL_CTRL_BYPASS_MASK,
+			     VCU_PLL_CTRL_BYPASS_SHIFT);
+	xvcu_write_field_reg(xvcu->vcu_slcr_ba, VCU_PLL_CTRL,
+			     1, VCU_PLL_CTRL_RESET_MASK,
+			     VCU_PLL_CTRL_RESET_SHIFT);
+	xvcu_write_field_reg(xvcu->vcu_slcr_ba, VCU_PLL_CTRL,
+			     0, VCU_PLL_CTRL_RESET_MASK,
+			     VCU_PLL_CTRL_RESET_SHIFT);
+	/*
+	 * Defined the timeout for the max time to wait the
+	 * PLL_STATUS to be locked.
+	 */
+	timeout = jiffies + msecs_to_jiffies(2000);
+	do {
+		lock_status = xvcu_read(xvcu->vcu_slcr_ba, VCU_PLL_STATUS);
+		if (lock_status & VCU_PLL_STATUS_LOCK_STATUS_MASK) {
+			xvcu_write_field_reg(xvcu->vcu_slcr_ba, VCU_PLL_CTRL,
+					     0, VCU_PLL_CTRL_BYPASS_MASK,
+					     VCU_PLL_CTRL_BYPASS_SHIFT);
+			return 0;
+		}
+	} while (!time_after(jiffies, timeout));
+
+	/* PLL is not locked even after the timeout of the 2sec */
+	dev_err(xvcu->dev, "PLL is not locked\n");
+	return -ETIMEDOUT;
+}
+
+/**
+ * xvcu_probe - Probe existence of the logicoreIP
+ *			and initialize PLL
+ *
+ * @pdev:	Pointer to the platform_device structure
+ *
+ * Return:	Returns 0 on success
+ *		Negative error code otherwise
+ */
+static int xvcu_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	struct xvcu_device *xvcu;
+	int ret;
+
+	xvcu = devm_kzalloc(&pdev->dev, sizeof(*xvcu), GFP_KERNEL);
+	if (!xvcu)
+		return -ENOMEM;
+
+	xvcu->dev = &pdev->dev;
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "vcu_slcr");
+	if (!res) {
+		dev_err(&pdev->dev, "get vcu_slcr memory resource failed.\n");
+		return -ENODEV;
+	}
+
+	xvcu->vcu_slcr_ba = devm_ioremap_nocache(&pdev->dev, res->start,
+						 resource_size(res));
+	if (!xvcu->vcu_slcr_ba) {
+		dev_err(&pdev->dev, "vcu_slcr register mapping failed.\n");
+		return -ENOMEM;
+	}
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "logicore");
+	if (!res) {
+		dev_err(&pdev->dev, "get logicore memory resource failed.\n");
+		return -ENODEV;
+	}
+
+	xvcu->logicore_reg_ba = devm_ioremap_nocache(&pdev->dev, res->start,
+						     resource_size(res));
+	if (!xvcu->logicore_reg_ba) {
+		dev_err(&pdev->dev, "logicore register mapping failed.\n");
+		return -ENOMEM;
+	}
+
+	xvcu->aclk = devm_clk_get(&pdev->dev, "aclk");
+	if (IS_ERR(xvcu->aclk)) {
+		dev_err(&pdev->dev, "Could not get aclk clock\n");
+		return PTR_ERR(xvcu->aclk);
+	}
+
+	xvcu->pll_ref = devm_clk_get(&pdev->dev, "pll_ref");
+	if (IS_ERR(xvcu->pll_ref)) {
+		dev_err(&pdev->dev, "Could not get pll_ref clock\n");
+		return PTR_ERR(xvcu->pll_ref);
+	}
+
+	ret = clk_prepare_enable(xvcu->aclk);
+	if (ret) {
+		dev_err(&pdev->dev, "aclk clock enable failed\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(xvcu->pll_ref);
+	if (ret) {
+		dev_err(&pdev->dev, "pll_ref clock enable failed\n");
+		goto error_aclk;
+	}
+
+	/*
+	 * Do the Gasket isolation and put the VCU out of reset
+	 * Bit 0 : Gasket isolation
+	 * Bit 1 : put VCU out of reset
+	 */
+	xvcu_write(xvcu->logicore_reg_ba, VCU_GASKET_INIT, VCU_GASKET_VALUE);
+
+	/* Do the PLL Settings based on the ref clk,core and mcu clk freq */
+	ret = xvcu_set_pll(xvcu);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to set the pll\n");
+		goto error_pll_ref;
+	}
+
+	dev_set_drvdata(&pdev->dev, xvcu);
+
+	dev_info(&pdev->dev, "%s: Probed successfully\n", __func__);
+
+	return 0;
+
+error_pll_ref:
+	clk_disable_unprepare(xvcu->pll_ref);
+error_aclk:
+	clk_disable_unprepare(xvcu->aclk);
+	return ret;
+}
+
+/**
+ * xvcu_remove - Insert gasket isolation
+ *			and disable the clock
+ * @pdev:	Pointer to the platform_device structure
+ *
+ * Return:	Returns 0 on success
+ *		Negative error code otherwise
+ */
+static int xvcu_remove(struct platform_device *pdev)
+{
+	struct xvcu_device *xvcu;
+
+	xvcu = platform_get_drvdata(pdev);
+	if (!xvcu)
+		return -ENODEV;
+
+	/* Add the the Gasket isolation and put the VCU in reset. */
+	xvcu_write(xvcu->logicore_reg_ba, VCU_GASKET_INIT, 0);
+
+	clk_disable_unprepare(xvcu->pll_ref);
+	clk_disable_unprepare(xvcu->aclk);
+
+	return 0;
+}
+
+static const struct of_device_id xvcu_of_id_table[] = {
+	{ .compatible = "xlnx,vcu" },
+	{ .compatible = "xlnx,vcu-logicoreip-1.0" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, xvcu_of_id_table);
+
+static struct platform_driver xvcu_driver = {
+	.driver = {
+		.name           = "xilinx-vcu",
+		.of_match_table = xvcu_of_id_table,
+	},
+	.probe                  = xvcu_probe,
+	.remove                 = xvcu_remove,
+};
+
+module_platform_driver(xvcu_driver);
+
+MODULE_AUTHOR("Dhaval Shah <dshah@xilinx.com>");
+MODULE_DESCRIPTION("Xilinx VCU init Driver");
+MODULE_LICENSE("GPL v2");