ARM: dts: dra7: Use sdhci-omap programming model

Use sdhci-omap programming model based on the generic sdhci
library for programming the eMMC/SD/SDIO controller.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi

@@ -444,8 +444,8 @@
 	vmmc-supply = <&vdd_3v3>;
 	vqmmc-supply = <&vdd_3v3>;
 	bus-width = <8>;
-	ti,non-removable;
-	cap-mmc-dual-data-rate;
+	non-removable;
+	no-1-8-v;
 };
 
 &sata {

arch/arm/boot/dts/am57xx-beagle-x15.dts

@@ -25,6 +25,7 @@
 	pinctrl-1 = <&mmc1_pins_hs>;
 
 	vmmc-supply = <&ldo1_reg>;
+	no-1-8-v;
 };
 
 &mmc2 {

arch/arm/boot/dts/am57xx-idk-common.dtsi

@@ -412,8 +412,9 @@
 	vmmc-supply = <&v3_3d>;
 	vqmmc-supply = <&v3_3d>;
 	bus-width = <8>;
-	ti,non-removable;
+	non-removable;
 	max-frequency = <96000000>;
+	no-1-8-v;
 };
 
 &dcan1 {

arch/arm/boot/dts/dra7-evm.dts

@@ -377,6 +377,7 @@
 	vmmc-supply = <&evm_1v8_sw>;
 	vqmmc-supply = <&evm_1v8_sw>;
 	bus-width = <8>;
+	non-removable;
 	pinctrl-names = "default", "hs", "ddr_1_8v-rev11", "ddr_1_8v", "hs200_1_8v-rev11", "hs200_1_8v";
 	pinctrl-0 = <&mmc2_pins_default>;
 	pinctrl-1 = <&mmc2_pins_hs>;

arch/arm/boot/dts/dra7.dtsi

@@ -1079,14 +1079,10 @@
 		};
 
 		mmc1: mmc@4809c000 {
-			compatible = "ti,omap4-hsmmc";
+			compatible = "ti,dra7-sdhci";
 			reg = <0x4809c000 0x400>;
 			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmc1";
-			ti,dual-volt;
-			ti,needs-special-reset;
-			dmas = <&sdma_xbar 61>, <&sdma_xbar 62>;
-			dma-names = "tx", "rx";
 			status = "disabled";
 			pbias-supply = <&pbias_mmc_reg>;
 			max-frequency = <192000000>;
@@ -1100,40 +1096,37 @@
 		};
 
 		mmc2: mmc@480b4000 {
-			compatible = "ti,omap4-hsmmc";
+			compatible = "ti,dra7-sdhci";
 			reg = <0x480b4000 0x400>;
 			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmc2";
-			ti,needs-special-reset;
-			dmas = <&sdma_xbar 47>, <&sdma_xbar 48>;
-			dma-names = "tx", "rx";
 			status = "disabled";
 			max-frequency = <192000000>;
+			/* SDR104/DDR50/SDR50 bits in CAPA2 is not supported */
+			sdhci-caps-mask = <0x7 0x0>;
 		};
 
 		mmc3: mmc@480ad000 {
-			compatible = "ti,omap4-hsmmc";
+			compatible = "ti,dra7-sdhci";
 			reg = <0x480ad000 0x400>;
 			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmc3";
-			ti,needs-special-reset;
-			dmas = <&sdma_xbar 77>, <&sdma_xbar 78>;
-			dma-names = "tx", "rx";
 			status = "disabled";
 			/* Errata i887 limits max-frequency of MMC3 to 64 MHz */
 			max-frequency = <64000000>;
+			/* SDMA is not supported */
+			sdhci-caps-mask = <0x0 0x400000>;
 		};
 
 		mmc4: mmc@480d1000 {
-			compatible = "ti,omap4-hsmmc";
+			compatible = "ti,dra7-sdhci";
 			reg = <0x480d1000 0x400>;
 			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmc4";
-			ti,needs-special-reset;
-			dmas = <&sdma_xbar 57>, <&sdma_xbar 58>;
-			dma-names = "tx", "rx";
 			status = "disabled";
 			max-frequency = <192000000>;
+			/* SDMA is not supported */
+			sdhci-caps-mask = <0x0 0x400000>;
 		};
 
 		mmu0_dsp1: mmu@40d01000 {

arch/arm/boot/dts/dra72-evm-common.dtsi

@@ -413,7 +413,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins_default>;
 	bus-width = <8>;
-	ti,non-removable;
+	non-removable;
 	max-frequency = <192000000>;
 };
 

arch/arm/boot/dts/dra76-evm.dts

@@ -327,7 +327,7 @@
 &mmc1 {
 	status = "okay";
 	vmmc-supply = <&vio_3v3_sd>;
-	vmmc_aux-supply = <&ldo4_reg>;
+	vqmmc-supply = <&ldo4_reg>;
 	bus-width = <4>;
 	/*
 	 * SDCD signal is not being used here - using the fact that GPIO mode
@@ -344,6 +344,7 @@
 	vmmc-supply = <&vio_1v8>;
 	vqmmc-supply = <&vio_1v8>;
 	bus-width = <8>;
+	non-removable;
 	pinctrl-names = "default", "hs", "ddr_1_8v", "hs200_1_8v";
 	pinctrl-0 = <&mmc2_pins_default>;
 	pinctrl-1 = <&mmc2_pins_default>;