Skip to content

K
kernel_linux

OpenHarmony / kernel_linux
上一次同步 4 年多

通知 15
Star 8
Fork 2
K
kernel_linux
提交 909eacd7 编写于 作者: G Greg Kroah-Hartman
浏览文件
操作

Merge 4.1-rc4 into usb-next 

We want the fixes in here as well.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
上级 aa519be3 e2608180
展开全部 隐藏空白更改
内联 并排
Showing with 6079 addition and 4847 deletion
CREDITS
浏览文件 @ 909eacd7
......@@ -3709,6 +3709,13 @@ N: Dirk Verworner
D: Co-author of German book ``Linux-Kernel-Programmierung''
D: Co-founder of Berlin Linux User Group
N: Andrew Victor
E: linux@maxim.org.za
W: http://maxim.org.za/at91_26.html
D: First maintainer of Atmel ARM-based SoC, aka AT91
D: Introduced support for at91rm9200, the first chip of AT91 family
S: South Africa
N: Riku Voipio
E: riku.voipio@iki.fi
D: Author of PCA9532 LED and Fintek f75375s hwmon driver
......
Documentation/IPMI.txt
浏览文件 @ 909eacd7
......@@ -505,7 +505,10 @@ at module load time (for a module) with:
The addresses are normal I2C addresses. The adapter is the string
name of the adapter, as shown in /sys/class/i2c-adapter/i2c-<n>/name.
It is *NOT* i2c-<n> itself.
It is *NOT* i2c-<n> itself. Also, the comparison is done ignoring
spaces, so if the name is "This is an I2C chip" you can say
adapter_name=ThisisanI2cchip. This is because it's hard to pass in
spaces in kernel parameters.
The debug flags are bit flags for each BMC found, they are:
IPMI messages: 1, driver state: 2, timing: 4, I2C probe: 8
......
Documentation/acpi/enumeration.txt
浏览文件 @ 909eacd7
......@@ -253,7 +253,7 @@ input driver:
GPIO support
~~~~~~~~~~~~
ACPI 5 introduced two new resources to describe GPIO connections: GpioIo
and GpioInt. These resources are used be used to pass GPIO numbers used by
and GpioInt. These resources can be used to pass GPIO numbers used by
the device to the driver. ACPI 5.1 extended this with _DSD (Device
Specific Data) which made it possible to name the GPIOs among other things.
......
Documentation/acpi/gpio-properties.txt
浏览文件 @ 909eacd7
_DSD Device Properties Related to GPIO
--------------------------------------
With the release of ACPI 5.1 and the _DSD configuration objecte names
can finally be given to GPIOs (and other things as well) returned by
_CRS. Previously, we were only able to use an integer index to find
With the release of ACPI 5.1, the _DSD configuration object finally
allows names to be given to GPIOs (and other things as well) returned
by _CRS. Previously, we were only able to use an integer index to find
the corresponding GPIO, which is pretty error prone (it depends on
the _CRS output ordering, for example).
......
Documentation/devicetree/bindings/arm/omap/l3-noc.txt
浏览文件 @ 909eacd7
......@@ -6,6 +6,7 @@ provided by Arteris.
Required properties:
- compatible : Should be "ti,omap3-l3-smx" for OMAP3 family
Should be "ti,omap4-l3-noc" for OMAP4 family
Should be "ti,omap5-l3-noc" for OMAP5 family
Should be "ti,dra7-l3-noc" for DRA7 family
Should be "ti,am4372-l3-noc" for AM43 family
- reg: Contains L3 register address range for each noc domain.
......
Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt
浏览文件 @ 909eacd7
......@@ -38,7 +38,7 @@ dma_apbx: dma-apbx@80024000 {
80 81 68 69
70 71 72 73
74 75 76 77>;
interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty",
interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty",
"saif0", "saif1", "i2c0", "i2c1",
"auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx",
"auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx";
......
Documentation/devicetree/bindings/mtd/m25p80.txt → Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt
浏览文件 @ 909eacd7
......@@ -8,8 +8,8 @@ Required properties:
is not Linux-only, but in case of Linux, see the "m25p_ids"
table in drivers/mtd/devices/m25p80.c for the list of supported
chips.
Must also include "nor-jedec" for any SPI NOR flash that can be
identified by the JEDEC READ ID opcode (0x9F).
Must also include "jedec,spi-nor" for any SPI NOR flash that can
be identified by the JEDEC READ ID opcode (0x9F).
- reg : Chip-Select number
- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
......@@ -25,7 +25,7 @@ Example:
flash: m25p80@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "spansion,m25p80", "nor-jedec";
compatible = "spansion,m25p80", "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <40000000>;
m25p,fast-read;
......
Documentation/devicetree/bindings/rtc/abracon,abx80x.txt 0 → 100644
浏览文件 @ 909eacd7
Abracon ABX80X I2C ultra low power RTC/Alarm chip
The Abracon ABX80X family consist of the ab0801, ab0803, ab0804, ab0805, ab1801,
ab1803, ab1804 and ab1805. The ab0805 is the superset of ab080x and the ab1805
is the superset of ab180x.
Required properties:
- "compatible": should one of:
"abracon,abx80x"
"abracon,ab0801"
"abracon,ab0803"
"abracon,ab0804"
"abracon,ab0805"
"abracon,ab1801"
"abracon,ab1803"
"abracon,ab1804"
"abracon,ab1805"
Using "abracon,abx80x" will enable chip autodetection.
- "reg": I2C bus address of the device
Optional properties:
The abx804 and abx805 have a trickle charger that is able to charge the
connected battery or supercap. Both the following properties have to be defined
and valid to enable charging:
- "abracon,tc-diode": should be "standard" (0.6V) or "schottky" (0.3V)
- "abracon,tc-resistor": should be <0>, <3>, <6> or <11>. 0 disables the output
resistor, the other values are in ohm.
Documentation/kasan.txt
浏览文件 @ 909eacd7
......@@ -9,7 +9,9 @@ a fast and comprehensive solution for finding use-after-free and out-of-bounds
bugs.
KASan uses compile-time instrumentation for checking every memory access,
therefore you will need a certain version of GCC > 4.9.2
therefore you will need a gcc version of 4.9.2 or later. KASan could detect out
of bounds accesses to stack or global variables, but only if gcc 5.0 or later was
used to built the kernel.
Currently KASan is supported only for x86_64 architecture and requires that the
kernel be built with the SLUB allocator.
......@@ -23,8 +25,8 @@ To enable KASAN configure kernel with:
and choose between CONFIG_KASAN_OUTLINE and CONFIG_KASAN_INLINE. Outline/inline
is compiler instrumentation types. The former produces smaller binary the
latter is 1.1 - 2 times faster. Inline instrumentation requires GCC 5.0 or
latter.
latter is 1.1 - 2 times faster. Inline instrumentation requires a gcc version
of 5.0 or later.
Currently KASAN works only with the SLUB memory allocator.
For better bug detection and nicer report, enable CONFIG_STACKTRACE and put
......
Documentation/serial/tty.txt
浏览文件 @ 909eacd7
......@@ -198,6 +198,9 @@ TTY_IO_ERROR If set, causes all subsequent userspace read/write
TTY_OTHER_CLOSED Device is a pty and the other side has closed.
TTY_OTHER_DONE Device is a pty and the other side has closed and
all pending input processing has been completed.
TTY_NO_WRITE_SPLIT Prevent driver from splitting up writes into
smaller chunks.
......
MAINTAINERS
浏览文件 @ 909eacd7
......@@ -892,11 +892,10 @@ S: Maintained
F: arch/arm/mach-alpine/
ARM/ATMEL AT91RM9200 AND AT91SAM ARM ARCHITECTURES
M: Andrew Victor <linux@maxim.org.za>
M: Nicolas Ferre <nicolas.ferre@atmel.com>
M: Alexandre Belloni <alexandre.belloni@free-electrons.com>
M: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
W: http://maxim.org.za/at91_26.html
W: http://www.linux4sam.org
S: Supported
F: arch/arm/mach-at91/
......@@ -975,7 +974,7 @@ S: Maintained
ARM/CORTINA SYSTEMS GEMINI ARM ARCHITECTURE
M: Hans Ulli Kroll <ulli.kroll@googlemail.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
T: git git://git.berlios.de/gemini-board
T: git git://github.com/ulli-kroll/linux.git
S: Maintained
F: arch/arm/mach-gemini/
......@@ -990,6 +989,12 @@ F: drivers/clocksource/timer-prima2.c
F: drivers/clocksource/timer-atlas7.c
N: [^a-z]sirf
ARM/CONEXANT DIGICOLOR MACHINE SUPPORT
M: Baruch Siach <baruch@tkos.co.il>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
N: digicolor
ARM/EBSA110 MACHINE SUPPORT
M: Russell King <linux@arm.linux.org.uk>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
......@@ -1188,7 +1193,7 @@ ARM/MAGICIAN MACHINE SUPPORT
M: Philipp Zabel <philipp.zabel@gmail.com>
S: Maintained
ARM/Marvell Armada 370 and Armada XP SOC support
ARM/Marvell Kirkwood and Armada 370, 375, 38x, XP SOC support
M: Jason Cooper <jason@lakedaemon.net>
M: Andrew Lunn <andrew@lunn.ch>
M: Gregory Clement <gregory.clement@free-electrons.com>
......@@ -1197,12 +1202,17 @@ L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
F: arch/arm/mach-mvebu/
F: drivers/rtc/rtc-armada38x.c
F: arch/arm/boot/dts/armada*
F: arch/arm/boot/dts/kirkwood*
ARM/Marvell Berlin SoC support
M: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
F: arch/arm/mach-berlin/
F: arch/arm/boot/dts/berlin*
ARM/Marvell Dove/MV78xx0/Orion SOC support
M: Jason Cooper <jason@lakedaemon.net>
......@@ -1215,6 +1225,9 @@ F: arch/arm/mach-dove/
F: arch/arm/mach-mv78xx0/
F: arch/arm/mach-orion5x/
F: arch/arm/plat-orion/
F: arch/arm/boot/dts/dove*
F: arch/arm/boot/dts/orion5x*
ARM/Orion SoC/Technologic Systems TS-78xx platform support
M: Alexander Clouter <alex@digriz.org.uk>
......@@ -1366,6 +1379,7 @@ N: rockchip
ARM/SAMSUNG EXYNOS ARM ARCHITECTURES
M: Kukjin Kim <kgene@kernel.org>
M: Krzysztof Kozlowski <k.kozlowski@samsung.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
L: linux-samsung-soc@vger.kernel.org (moderated for non-subscribers)
S: Maintained
......@@ -1439,9 +1453,10 @@ ARM/SOCFPGA ARCHITECTURE
M: Dinh Nguyen <dinguyen@opensource.altera.com>
S: Maintained
F: arch/arm/mach-socfpga/
F: arch/arm/boot/dts/socfpga*
F: arch/arm/configs/socfpga_defconfig
W: http://www.rocketboards.org
T: git://git.rocketboards.org/linux-socfpga.git
T: git://git.rocketboards.org/linux-socfpga-next.git
T: git git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux.git
ARM/SOCFPGA CLOCK FRAMEWORK SUPPORT
M: Dinh Nguyen <dinguyen@opensource.altera.com>
......@@ -1929,7 +1944,7 @@ S: Maintained
F: drivers/net/wireless/b43legacy/
BACKLIGHT CLASS/SUBSYSTEM
M: Jingoo Han <jg1.han@samsung.com>
M: Jingoo Han <jingoohan1@gmail.com>
M: Lee Jones <lee.jones@linaro.org>
S: Maintained
F: drivers/video/backlight/
......@@ -2116,8 +2131,9 @@ S: Supported
F: drivers/net/ethernet/broadcom/bnx2x/
BROADCOM BCM281XX/BCM11XXX/BCM216XX ARM ARCHITECTURE
M: Christian Daudt <bcm@fixthebug.org>
M: Florian Fainelli <f.fainelli@gmail.com>
M: Ray Jui <rjui@broadcom.com>
M: Scott Branden <sbranden@broadcom.com>
L: bcm-kernel-feedback-list@broadcom.com
T: git git://github.com/broadcom/mach-bcm
S: Maintained
......@@ -2168,7 +2184,6 @@ S: Maintained
F: drivers/usb/gadget/udc/bcm63xx_udc.*
BROADCOM BCM7XXX ARM ARCHITECTURE
M: Marc Carino <marc.ceeeee@gmail.com>
M: Brian Norris <computersforpeace@gmail.com>
M: Gregory Fong <gregory.0xf0@gmail.com>
M: Florian Fainelli <f.fainelli@gmail.com>
......@@ -3912,7 +3927,7 @@ F: drivers/extcon/
F: Documentation/extcon/
EXYNOS DP DRIVER
M: Jingoo Han <jg1.han@samsung.com>
M: Jingoo Han <jingoohan1@gmail.com>
L: dri-devel@lists.freedesktop.org
S: Maintained
F: drivers/gpu/drm/exynos/exynos_dp*
......@@ -4371,11 +4386,10 @@ F: fs/gfs2/
F: include/uapi/linux/gfs2_ondisk.h
GIGASET ISDN DRIVERS
M: Hansjoerg Lipp <hjlipp@web.de>
M: Tilman Schmidt <tilman@imap.cc>
M: Paul Bolle <pebolle@tiscali.nl>
L: gigaset307x-common@lists.sourceforge.net
W: http://gigaset307x.sourceforge.net/
S: Maintained
S: Odd Fixes
F: Documentation/isdn/README.gigaset
F: drivers/isdn/gigaset/
F: include/uapi/linux/gigaset_dev.h
......@@ -5042,17 +5056,19 @@ S: Orphan
F: drivers/video/fbdev/imsttfb.c
INFINIBAND SUBSYSTEM
M: Roland Dreier <roland@kernel.org>
M: Doug Ledford <dledford@redhat.com>
M: Sean Hefty <sean.hefty@intel.com>
M: Hal Rosenstock <hal.rosenstock@gmail.com>
L: linux-rdma@vger.kernel.org
W: http://www.openfabrics.org/
Q: http://patchwork.kernel.org/project/linux-rdma/list/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband.git
T: git git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma.git
S: Supported
F: Documentation/infiniband/
F: drivers/infiniband/
F: include/uapi/linux/if_infiniband.h
F: include/uapi/rdma/
F: include/rdma/
INOTIFY
M: John McCutchan <john@johnmccutchan.com>
......@@ -5805,6 +5821,7 @@ F: drivers/scsi/53c700*
LED SUBSYSTEM
M: Bryan Wu <cooloney@gmail.com>
M: Richard Purdie <rpurdie@rpsys.net>
M: Jacek Anaszewski <j.anaszewski@samsung.com>
L: linux-leds@vger.kernel.org
T: git git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds.git
S: Maintained
......@@ -6950,6 +6967,17 @@ T: git git://git.rocketboards.org/linux-socfpga-next.git
S: Maintained
F: arch/nios2/
NOKIA N900 POWER SUPPLY DRIVERS
M: Pali Rohár <pali.rohar@gmail.com>
S: Maintained
F: include/linux/power/bq2415x_charger.h
F: include/linux/power/bq27x00_battery.h
F: include/linux/power/isp1704_charger.h
F: drivers/power/bq2415x_charger.c
F: drivers/power/bq27x00_battery.c
F: drivers/power/isp1704_charger.c
F: drivers/power/rx51_battery.c
NTB DRIVER
M: Jon Mason <jdmason@kudzu.us>
M: Dave Jiang <dave.jiang@intel.com>
......@@ -7538,7 +7566,7 @@ S: Maintained
F: drivers/pci/host/*rcar*
PCI DRIVER FOR SAMSUNG EXYNOS
M: Jingoo Han <jg1.han@samsung.com>
M: Jingoo Han <jingoohan1@gmail.com>
L: linux-pci@vger.kernel.org
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
L: linux-samsung-soc@vger.kernel.org (moderated for non-subscribers)
......@@ -7546,7 +7574,7 @@ S: Maintained
F: drivers/pci/host/pci-exynos.c
PCI DRIVER FOR SYNOPSIS DESIGNWARE
M: Jingoo Han <jg1.han@samsung.com>
M: Jingoo Han <jingoohan1@gmail.com>
L: linux-pci@vger.kernel.org
S: Maintained
F: drivers/pci/host/*designware*
......@@ -8502,7 +8530,7 @@ S: Supported
F: sound/soc/samsung/
SAMSUNG FRAMEBUFFER DRIVER
M: Jingoo Han <jg1.han@samsung.com>
M: Jingoo Han <jingoohan1@gmail.com>
L: linux-fbdev@vger.kernel.org
S: Maintained
F: drivers/video/fbdev/s3c-fb.c
......@@ -8807,10 +8835,11 @@ W: http://www.emulex.com
S: Supported
F: drivers/scsi/be2iscsi/
SERVER ENGINES 10Gbps NIC - BladeEngine 2 DRIVER
M: Sathya Perla <sathya.perla@emulex.com>
M: Subbu Seetharaman <subbu.seetharaman@emulex.com>
M: Ajit Khaparde <ajit.khaparde@emulex.com>
Emulex 10Gbps NIC BE2, BE3-R, Lancer, Skyhawk-R DRIVER
M: Sathya Perla <sathya.perla@avagotech.com>
M: Ajit Khaparde <ajit.khaparde@avagotech.com>
M: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
M: Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com>
L: netdev@vger.kernel.org
W: http://www.emulex.com
S: Supported
......@@ -11037,6 +11066,7 @@ F: drivers/media/pci/zoran/
ZRAM COMPRESSED RAM BLOCK DEVICE DRVIER
M: Minchan Kim <minchan@kernel.org>
M: Nitin Gupta <ngupta@vflare.org>
R: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
L: linux-kernel@vger.kernel.org
S: Maintained
F: drivers/block/zram/
......
Makefile
浏览文件 @ 909eacd7
VERSION = 4
PATCHLEVEL = 1
SUBLEVEL = 0
EXTRAVERSION = -rc2
EXTRAVERSION = -rc4
NAME = Hurr durr I'ma sheep
# *DOCUMENTATION*
......
arch/arc/Kconfig.debug
浏览文件 @ 909eacd7
......@@ -2,19 +2,6 @@ menu "Kernel hacking"
source "lib/Kconfig.debug"
config EARLY_PRINTK
bool "Early printk" if EMBEDDED
default y
help
Write kernel log output directly into the VGA buffer or to a serial
port.
This is useful for kernel debugging when your machine crashes very
early before the console code is initialized. For normal operation
it is not recommended because it looks ugly and doesn't cooperate
with klogd/syslogd or the X server. You should normally N here,
unless you want to debug such a crash.
config 16KSTACKS
bool "Use 16Kb for kernel stacks instead of 8Kb"
help
......
arch/arc/include/asm/atomic.h
浏览文件 @ 909eacd7
......@@ -99,7 +99,7 @@ static inline void atomic_##op(int i, atomic_t *v) \
atomic_ops_unlock(flags); \
}
#define ATOMIC_OP_RETURN(op, c_op) \
#define ATOMIC_OP_RETURN(op, c_op, asm_op) \
static inline int atomic_##op##_return(int i, atomic_t *v) \
{ \
unsigned long flags; \
......
arch/arc/mm/cache_arc700.c
浏览文件 @ 909eacd7
......@@ -266,7 +266,7 @@ static inline void __cache_line_loop(unsigned long paddr, unsigned long vaddr,
* Machine specific helpers for Entire D-Cache or Per Line ops
*/
static unsigned int __before_dc_op(const int op)
static inline unsigned int __before_dc_op(const int op)
{
unsigned int reg = reg;
......@@ -284,7 +284,7 @@ static unsigned int __before_dc_op(const int op)
return reg;
}
static void __after_dc_op(const int op, unsigned int reg)
static inline void __after_dc_op(const int op, unsigned int reg)
{
if (op & OP_FLUSH) /* flush / flush-n-inv both wait */
while (read_aux_reg(ARC_REG_DC_CTRL) & DC_CTRL_FLUSH_STATUS);
......
arch/arm/boot/dts/am437x-sk-evm.dts
浏览文件 @ 909eacd7
......@@ -49,7 +49,7 @@
pinctrl-0 = <&matrix_keypad_pins>;
debounce-delay-ms = <5>;
col-scan-delay-us = <1500>;
col-scan-delay-us = <5>;
row-gpios = <&gpio5 5 GPIO_ACTIVE_HIGH /* Bank5, pin5 */
&gpio5 6 GPIO_ACTIVE_HIGH>; /* Bank5, pin6 */
......@@ -473,7 +473,7 @@
interrupt-parent = <&gpio0>;
interrupts = <31 0>;
wake-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
reset-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
touchscreen-size-x = <480>;
touchscreen-size-y = <272>;
......
arch/arm/boot/dts/am57xx-beagle-x15.dts
浏览文件 @ 909eacd7
......@@ -18,6 +18,7 @@
aliases {
rtc0 = &mcp_rtc;
rtc1 = &tps659038_rtc;
rtc2 = &rtc;
};
memory {
......@@ -83,7 +84,7 @@
gpio_fan: gpio_fan {
/* Based on 5v 500mA AFB02505HHB */
compatible = "gpio-fan";
gpios = <&tps659038_gpio 1 GPIO_ACTIVE_HIGH>;
gpios = <&tps659038_gpio 2 GPIO_ACTIVE_HIGH>;
gpio-fan,speed-map = <0 0>,
<13000 1>;
#cooling-cells = <2>;
......@@ -130,8 +131,8 @@
uart3_pins_default: uart3_pins_default {
pinctrl-single,pins = <
0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd.rxd */
0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd.txd */
0x3f8 (PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */
0x3fc (PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */
>;
};
......@@ -455,7 +456,7 @@
mcp_rtc: rtc@6f {
compatible = "microchip,mcp7941x";
reg = <0x6f>;
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_LOW>; /* IRQ_SYS_1N */
interrupts = <GIC_SPI 2 IRQ_TYPE_EDGE_RISING>; /* IRQ_SYS_1N */
pinctrl-names = "default";
pinctrl-0 = <&mcp79410_pins_default>;
......@@ -478,7 +479,7 @@
&uart3 {
status = "okay";
interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
<&dra7_pmx_core 0x248>;
<&dra7_pmx_core 0x3f8>;
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins_default>;
......
arch/arm/boot/dts/armada-375.dtsi
浏览文件 @ 909eacd7
......@@ -69,7 +69,7 @@
mainpll: mainpll {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <2000000000>;
clock-frequency = <1000000000>;
};
/* 25 MHz reference crystal */
refclk: oscillator {
......
arch/arm/boot/dts/armada-38x.dtsi
浏览文件 @ 909eacd7
......@@ -585,7 +585,7 @@
mainpll: mainpll {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <2000000000>;
clock-frequency = <1000000000>;
};
/* 25 MHz reference crystal */
......
arch/arm/boot/dts/armada-39x.dtsi
浏览文件 @ 909eacd7
......@@ -502,7 +502,7 @@
mainpll: mainpll {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <2000000000>;
clock-frequency = <1000000000>;
};
};
};
arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
浏览文件 @ 909eacd7
......@@ -105,6 +105,10 @@
};
internal-regs {
rtc@10300 {
/* No crystal connected to the internal RTC */
status = "disabled";
};
serial@12000 {
status = "okay";
};
......
arch/arm/boot/dts/dove-cubox.dts
浏览文件 @ 909eacd7
......@@ -87,6 +87,7 @@
/* connect xtal input to 25MHz reference */
clocks = <&ref25>;
clock-names = "xtal";
/* connect xtal input as source of pll0 and pll1 */
silabs,pll-source = <0 0>, <1 0>;
......
arch/arm/boot/dts/dra7.dtsi
浏览文件 @ 909eacd7
......@@ -911,7 +911,7 @@
ti,clock-cycles = <16>;
reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>,
<0x4ae06014 0x4>, <0x4a003b20 0x8>,
<0x4ae06014 0x4>, <0x4a003b20 0xc>,
<0x4ae0c158 0x4>;
reg-names = "setup-address", "control-address",
"int-address", "efuse-address",
......@@ -944,7 +944,7 @@
ti,clock-cycles = <16>;
reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>,
<0x4ae06010 0x4>, <0x4a0025cc 0x8>,
<0x4ae06010 0x4>, <0x4a0025cc 0xc>,
<0x4a002470 0x4>;
reg-names = "setup-address", "control-address",
"int-address", "efuse-address",
......@@ -977,7 +977,7 @@
ti,clock-cycles = <16>;
reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>,
<0x4ae06010 0x4>, <0x4a0025e0 0x8>,
<0x4ae06010 0x4>, <0x4a0025e0 0xc>,
<0x4a00246c 0x4>;
reg-names = "setup-address", "control-address",
"int-address", "efuse-address",
......@@ -1010,7 +1010,7 @@
ti,clock-cycles = <16>;
reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>,
<0x4ae06010 0x4>, <0x4a003b08 0x8>,
<0x4ae06010 0x4>, <0x4a003b08 0xc>,
<0x4ae0c154 0x4>;
reg-names = "setup-address", "control-address",
"int-address", "efuse-address",
......@@ -1203,7 +1203,7 @@
status = "disabled";
};
rtc@48838000 {
rtc: rtc@48838000 {
compatible = "ti,am3352-rtc";
reg = <0x48838000 0x100>;
interrupts = <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
......
arch/arm/boot/dts/exynos4412-odroid-common.dtsi
浏览文件 @ 909eacd7
......@@ -9,6 +9,7 @@
#include <dt-bindings/sound/samsung-i2s.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/clock/maxim,max77686.h>
#include "exynos4412.dtsi"
/ {
......@@ -105,6 +106,8 @@
rtc@10070000 {
status = "okay";
clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
clock-names = "rtc", "rtc_src";
};
g2d@10800000 {
......
arch/arm/boot/dts/exynos5250-snow.dts
浏览文件 @ 909eacd7
......@@ -567,6 +567,7 @@
num-slots = <1>;
broken-cd;
cap-sdio-irq;
keep-power-in-suspend;
card-detect-delay = <200>;
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <2 3>;
......
arch/arm/boot/dts/exynos5420-peach-pit.dts
浏览文件 @ 909eacd7
......@@ -711,6 +711,7 @@
num-slots = <1>;
broken-cd;
cap-sdio-irq;
keep-power-in-suspend;
card-detect-delay = <200>;
clock-frequency = <400000000>;
samsung,dw-mshc-ciu-div = <1>;
......
arch/arm/boot/dts/exynos5420-trip-points.dtsi
浏览文件 @ 909eacd7
......@@ -28,7 +28,7 @@ trips {
type = "active";
};
cpu-crit-0 {
temperature = <1200000>; /* millicelsius */
temperature = <120000>; /* millicelsius */
hysteresis = <0>; /* millicelsius */
type = "critical";
};
......
arch/arm/boot/dts/exynos5420.dtsi
浏览文件 @ 909eacd7
......@@ -536,6 +536,7 @@
clock-names = "dp";
phys = <&dp_phy>;
phy-names = "dp";
power-domains = <&disp_pd>;
};
mipi_phy: video-phy@10040714 {
......
arch/arm/boot/dts/exynos5440-trip-points.dtsi
浏览文件 @ 909eacd7
......@@ -18,7 +18,7 @@ trips {
type = "active";
};
cpu-crit-0 {
temperature = <1050000>; /* millicelsius */
temperature = <105000>; /* millicelsius */
hysteresis = <0>; /* millicelsius */
type = "critical";
};
......
arch/arm/boot/dts/exynos5800-peach-pi.dts
浏览文件 @ 909eacd7
......@@ -674,6 +674,7 @@
num-slots = <1>;
broken-cd;
cap-sdio-irq;
keep-power-in-suspend;
card-detect-delay = <200>;
clock-frequency = <400000000>;
samsung,dw-mshc-ciu-div = <1>;
......
arch/arm/boot/dts/imx23-olinuxino.dts
浏览文件 @ 909eacd7
......@@ -12,6 +12,7 @@
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include "imx23.dtsi"
/ {
......@@ -93,6 +94,7 @@
ahb@80080000 {
usb0: usb@80080000 {
dr_mode = "host";
vbus-supply = <&reg_usb0_vbus>;
status = "okay";
};
......@@ -122,7 +124,7 @@
user {
label = "green";
gpios = <&gpio2 1 1>;
gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
};
};
};
arch/arm/boot/dts/imx25.dtsi
浏览文件 @ 909eacd7
......@@ -428,6 +428,7 @@
pwm4: pwm@53fc8000 {
compatible = "fsl,imx25-pwm", "fsl,imx27-pwm";
#pwm-cells = <2>;
reg = <0x53fc8000 0x4000>;
clocks = <&clks 108>, <&clks 52>;
clock-names = "ipg", "per";
......
arch/arm/boot/dts/imx28.dtsi
浏览文件 @ 909eacd7
......@@ -913,7 +913,7 @@
80 81 68 69
70 71 72 73
74 75 76 77>;
interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty",
interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty",
"saif0", "saif1", "i2c0", "i2c1",
"auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx",
"auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx";
......
arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
浏览文件 @ 909eacd7
......@@ -31,6 +31,7 @@
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio4 15 0>;
enable-active-high;
};
reg_usb_h1_vbus: regulator@1 {
......@@ -40,6 +41,7 @@
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio1 0 0>;
enable-active-high;
};
};
......
arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
浏览文件 @ 909eacd7
......@@ -185,7 +185,6 @@
&i2c3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
pinctrl-assert-gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
status = "okay";
max7310_a: gpio@30 {
......
arch/arm/boot/dts/omap3-n900.dts
浏览文件 @ 909eacd7
......@@ -498,6 +498,8 @@
DRVDD-supply = <&vmmc2>;
IOVDD-supply = <&vio>;
DVDD-supply = <&vio>;
ai3x-micbias-vg = <1>;
};
tlv320aic3x_aux: tlv320aic3x@19 {
......@@ -509,6 +511,8 @@
DRVDD-supply = <&vmmc2>;
IOVDD-supply = <&vio>;
DVDD-supply = <&vio>;
ai3x-micbias-vg = <2>;
};
tsl2563: tsl2563@29 {
......
arch/arm/boot/dts/omap3.dtsi
浏览文件 @ 909eacd7
......@@ -456,6 +456,7 @@
};
mmu_isp: mmu@480bd400 {
#iommu-cells = <0>;
compatible = "ti,omap2-iommu";
reg = <0x480bd400 0x80>;
interrupts = <24>;
......@@ -464,6 +465,7 @@
};
mmu_iva: mmu@5d000000 {
#iommu-cells = <0>;
compatible = "ti,omap2-iommu";
reg = <0x5d000000 0x80>;
interrupts = <28>;
......
arch/arm/boot/dts/omap5.dtsi
浏览文件 @ 909eacd7
......@@ -128,7 +128,7 @@
* hierarchy.
*/
ocp {
compatible = "ti,omap4-l3-noc", "simple-bus";
compatible = "ti,omap5-l3-noc", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
......
arch/arm/boot/dts/r8a7791-koelsch.dts
浏览文件 @ 909eacd7
......@@ -545,7 +545,7 @@
compatible = "adi,adv7511w";
reg = <0x39>;
interrupt-parent = <&gpio3>;
interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
adi,input-depth = <8>;
adi,input-colorspace = "rgb";
......
arch/arm/boot/dts/ste-dbx5x0.dtsi
浏览文件 @ 909eacd7
......@@ -1017,23 +1017,6 @@
status = "disabled";
};
vmmci: regulator-gpio {
compatible = "regulator-gpio";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2900000>;
regulator-name = "mmci-reg";
regulator-type = "voltage";
startup-delay-us = <100>;
enable-active-high;
states = <1800000 0x1
2900000 0x0>;
status = "disabled";
};
mcde@a0350000 {
compatible = "stericsson,mcde";
reg = <0xa0350000 0x1000>, /* MCDE */
......
arch/arm/boot/dts/ste-href.dtsi
浏览文件 @ 909eacd7
......@@ -111,6 +111,21 @@
pinctrl-1 = <&i2c3_sleep_mode>;
};
vmmci: regulator-gpio {
compatible = "regulator-gpio";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2900000>;
regulator-name = "mmci-reg";
regulator-type = "voltage";
startup-delay-us = <100>;
enable-active-high;
states = <1800000 0x1
2900000 0x0>;
};
// External Micro SD slot
sdi0_per1@80126000 {
arm,primecell-periphid = <0x10480180>;
......
arch/arm/boot/dts/ste-snowball.dts
浏览文件 @ 909eacd7
......@@ -146,8 +146,21 @@
};
vmmci: regulator-gpio {
compatible = "regulator-gpio";
gpios = <&gpio7 4 0x4>;
enable-gpio = <&gpio6 25 0x4>;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2900000>;
regulator-name = "mmci-reg";
regulator-type = "voltage";
startup-delay-us = <100>;
enable-active-high;
states = <1800000 0x1
2900000 0x0>;
};
// External Micro SD slot
......
arch/arm/boot/dts/tegra124.dtsi
浏览文件 @ 909eacd7
......@@ -826,7 +826,7 @@
<&tegra_car TEGRA124_CLK_PLL_U>,
<&tegra_car TEGRA124_CLK_USBD>;
clock-names = "reg", "pll_u", "utmi-pads";
resets = <&tegra_car 59>, <&tegra_car 22>;
resets = <&tegra_car 22>, <&tegra_car 22>;
reset-names = "usb", "utmi-pads";
nvidia,hssync-start-delay = <0>;
nvidia,idle-wait-delay = <17>;
......@@ -838,6 +838,7 @@
nvidia,hssquelch-level = <2>;
nvidia,hsdiscon-level = <5>;
nvidia,xcvr-hsslew = <12>;
nvidia,has-utmi-pad-registers;
status = "disabled";
};
......@@ -862,7 +863,7 @@
<&tegra_car TEGRA124_CLK_PLL_U>,
<&tegra_car TEGRA124_CLK_USBD>;
clock-names = "reg", "pll_u", "utmi-pads";
resets = <&tegra_car 22>, <&tegra_car 22>;
resets = <&tegra_car 58>, <&tegra_car 22>;
reset-names = "usb", "utmi-pads";
nvidia,hssync-start-delay = <0>;
nvidia,idle-wait-delay = <17>;
......@@ -874,7 +875,6 @@
nvidia,hssquelch-level = <2>;
nvidia,hsdiscon-level = <5>;
nvidia,xcvr-hsslew = <12>;
nvidia,has-utmi-pad-registers;
status = "disabled";
};
......@@ -899,7 +899,7 @@
<&tegra_car TEGRA124_CLK_PLL_U>,
<&tegra_car TEGRA124_CLK_USBD>;
clock-names = "reg", "pll_u", "utmi-pads";
resets = <&tegra_car 58>, <&tegra_car 22>;
resets = <&tegra_car 59>, <&tegra_car 22>;
reset-names = "usb", "utmi-pads";
nvidia,hssync-start-delay = <0>;
nvidia,idle-wait-delay = <17>;
......
arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts
浏览文件 @ 909eacd7
......@@ -191,6 +191,7 @@
compatible = "arm,cortex-a15-pmu";
interrupts = <0 68 4>,
<0 69 4>;
interrupt-affinity = <&cpu0>, <&cpu1>;
};
oscclk6a: oscclk6a {
......
arch/arm/boot/dts/vexpress-v2p-ca9.dts
浏览文件 @ 909eacd7
......@@ -33,28 +33,28 @@
#address-cells = <1>;
#size-cells = <0>;
cpu@0 {
A9_0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <0>;
next-level-cache = <&L2>;
};
cpu@1 {
A9_1: cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <1>;
next-level-cache = <&L2>;
};
cpu@2 {
A9_2: cpu@2 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <2>;
next-level-cache = <&L2>;
};
cpu@3 {
A9_3: cpu@3 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <3>;
......@@ -170,6 +170,7 @@
compatible = "arm,pl310-cache";
reg = <0x1e00a000 0x1000>;
interrupts = <0 43 4>;
cache-unified;
cache-level = <2>;
arm,data-latency = <1 1 1>;
arm,tag-latency = <1 1 1>;
......@@ -181,6 +182,8 @@
<0 61 4>,
<0 62 4>,
<0 63 4>;
interrupt-affinity = <&A9_0>, <&A9_1>, <&A9_2>, <&A9_3>;
};
dcc {
......
arch/arm/configs/multi_v7_defconfig
浏览文件 @ 909eacd7
......@@ -39,11 +39,14 @@ CONFIG_ARCH_HIP04=y
CONFIG_ARCH_KEYSTONE=y
CONFIG_ARCH_MESON=y
CONFIG_ARCH_MXC=y
CONFIG_SOC_IMX50=y
CONFIG_SOC_IMX51=y
CONFIG_SOC_IMX53=y
CONFIG_SOC_IMX6Q=y
CONFIG_SOC_IMX6SL=y
CONFIG_SOC_IMX6SX=y
CONFIG_SOC_VF610=y
CONFIG_SOC_LS1021A=y
CONFIG_ARCH_OMAP3=y
CONFIG_ARCH_OMAP4=y
CONFIG_SOC_OMAP5=y
......
arch/arm/configs/omap2plus_defconfig
浏览文件 @ 909eacd7
......@@ -393,7 +393,7 @@ CONFIG_TI_EDMA=y
CONFIG_DMA_OMAP=y
# CONFIG_IOMMU_SUPPORT is not set
CONFIG_EXTCON=m
CONFIG_EXTCON_GPIO=m
CONFIG_EXTCON_USB_GPIO=m
CONFIG_EXTCON_PALMAS=m
CONFIG_TI_EMIF=m
CONFIG_PWM=y
......
arch/arm/include/asm/dma-iommu.h
浏览文件 @ 909eacd7
......@@ -25,7 +25,7 @@ struct dma_iommu_mapping {
};
struct dma_iommu_mapping *
arm_iommu_create_mapping(struct bus_type *bus, dma_addr_t base, size_t size);
arm_iommu_create_mapping(struct bus_type *bus, dma_addr_t base, u64 size);
void arm_iommu_release_mapping(struct dma_iommu_mapping *mapping);
......
arch/arm/include/asm/xen/page.h
浏览文件 @ 909eacd7
......@@ -110,5 +110,6 @@ static inline bool set_phys_to_machine(unsigned long pfn, unsigned long mfn)
bool xen_arch_need_swiotlb(struct device *dev,
unsigned long pfn,
unsigned long mfn);
unsigned long xen_get_swiotlb_free_pages(unsigned int order);
#endif /* _ASM_ARM_XEN_PAGE_H */
arch/arm/kernel/perf_event_cpu.c
浏览文件 @ 909eacd7
......@@ -303,12 +303,17 @@ static int probe_current_pmu(struct arm_pmu *pmu)
static int of_pmu_irq_cfg(struct platform_device *pdev)
{
int i;
int i, irq;
int *irqs = kcalloc(pdev->num_resources, sizeof(*irqs), GFP_KERNEL);
if (!irqs)
return -ENOMEM;
/* Don't bother with PPIs; they're already affine */
irq = platform_get_irq(pdev, 0);
if (irq >= 0 && irq_is_percpu(irq))
return 0;
for (i = 0; i < pdev->num_resources; ++i) {
struct device_node *dn;
int cpu;
......@@ -317,7 +322,7 @@ static int of_pmu_irq_cfg(struct platform_device *pdev)
i);
if (!dn) {
pr_warn("Failed to parse %s/interrupt-affinity[%d]\n",
of_node_full_name(dn), i);
of_node_full_name(pdev->dev.of_node), i);
break;
}
......
arch/arm/mach-exynos/common.h
浏览文件 @ 909eacd7
......@@ -159,6 +159,8 @@ extern void exynos_enter_aftr(void);
extern struct cpuidle_exynos_data cpuidle_coupled_exynos_data;
extern void exynos_set_delayed_reset_assertion(bool enable);
extern void s5p_init_cpu(void __iomem *cpuid_addr);
extern unsigned int samsung_rev(void);
extern void __iomem *cpu_boot_reg_base(void);
......
arch/arm/mach-exynos/exynos.c
浏览文件 @ 909eacd7
......@@ -166,6 +166,33 @@ static void __init exynos_init_io(void)
exynos_map_io();
}
/*
* Set or clear the USE_DELAYED_RESET_ASSERTION option. Used by smp code
* and suspend.
*
* This is necessary only on Exynos4 SoCs. When system is running
* USE_DELAYED_RESET_ASSERTION should be set so the ARM CLK clock down
* feature could properly detect global idle state when secondary CPU is
* powered down.
*
* However this should not be set when such system is going into suspend.
*/
void exynos_set_delayed_reset_assertion(bool enable)
{
if (of_machine_is_compatible("samsung,exynos4")) {
unsigned int tmp, core_id;
for (core_id = 0; core_id < num_possible_cpus(); core_id++) {
tmp = pmu_raw_readl(EXYNOS_ARM_CORE_OPTION(core_id));
if (enable)
tmp |= S5P_USE_DELAYED_RESET_ASSERTION;
else
tmp &= ~(S5P_USE_DELAYED_RESET_ASSERTION);
pmu_raw_writel(tmp, EXYNOS_ARM_CORE_OPTION(core_id));
}
}
}
/*
* Apparently, these SoCs are not able to wake-up from suspend using
* the PMU. Too bad. Should they suddenly become capable of such a
......
arch/arm/mach-exynos/platsmp.c
浏览文件 @ 909eacd7
......@@ -34,30 +34,6 @@
extern void exynos4_secondary_startup(void);
/*
* Set or clear the USE_DELAYED_RESET_ASSERTION option, set on Exynos4 SoCs
* during hot-(un)plugging CPUx.
*
* The feature can be cleared safely during first boot of secondary CPU.
*
* Exynos4 SoCs require setting USE_DELAYED_RESET_ASSERTION during powering
* down a CPU so the CPU idle clock down feature could properly detect global
* idle state when CPUx is off.
*/
static void exynos_set_delayed_reset_assertion(u32 core_id, bool enable)
{
if (soc_is_exynos4()) {
unsigned int tmp;
tmp = pmu_raw_readl(EXYNOS_ARM_CORE_OPTION(core_id));
if (enable)
tmp |= S5P_USE_DELAYED_RESET_ASSERTION;
else
tmp &= ~(S5P_USE_DELAYED_RESET_ASSERTION);
pmu_raw_writel(tmp, EXYNOS_ARM_CORE_OPTION(core_id));
}
}
#ifdef CONFIG_HOTPLUG_CPU
static inline void cpu_leave_lowpower(u32 core_id)
{
......@@ -73,8 +49,6 @@ static inline void cpu_leave_lowpower(u32 core_id)
: "=&r" (v)
: "Ir" (CR_C), "Ir" (0x40)
: "cc");
exynos_set_delayed_reset_assertion(core_id, false);
}
static inline void platform_do_lowpower(unsigned int cpu, int *spurious)
......@@ -87,14 +61,6 @@ static inline void platform_do_lowpower(unsigned int cpu, int *spurious)
/* Turn the CPU off on next WFI instruction. */
exynos_cpu_power_down(core_id);
/*
* Exynos4 SoCs require setting
* USE_DELAYED_RESET_ASSERTION so the CPU idle
* clock down feature could properly detect
* global idle state when CPUx is off.
*/
exynos_set_delayed_reset_assertion(core_id, true);
wfi();
if (pen_release == core_id) {
......@@ -371,9 +337,6 @@ static int exynos_boot_secondary(unsigned int cpu, struct task_struct *idle)
udelay(10);
}
/* No harm if this is called during first boot of secondary CPU */
exynos_set_delayed_reset_assertion(core_id, false);
/*
* now the secondary core is starting up let it run its
* calibrations, then wait for it to finish
......@@ -420,6 +383,8 @@ static void __init exynos_smp_prepare_cpus(unsigned int max_cpus)
exynos_sysram_init();
exynos_set_delayed_reset_assertion(true);
if (read_cpuid_part() == ARM_CPU_PART_CORTEX_A9)
scu_enable(scu_base_addr());
......
arch/arm/mach-exynos/pm_domains.c
浏览文件 @ 909eacd7
......@@ -188,7 +188,7 @@ static __init int exynos4_pm_init_power_domain(void)
args.np = np;
args.args_count = 0;
child_domain = of_genpd_get_from_provider(&args);
if (!child_domain)
if (IS_ERR(child_domain))
continue;
if (of_parse_phandle_with_args(np, "power-domains",
......@@ -196,7 +196,7 @@ static __init int exynos4_pm_init_power_domain(void)
continue;
parent_domain = of_genpd_get_from_provider(&args);
if (!parent_domain)
if (IS_ERR(parent_domain))
continue;
if (pm_genpd_add_subdomain(parent_domain, child_domain))
......
arch/arm/mach-exynos/suspend.c
浏览文件 @ 909eacd7
......@@ -342,6 +342,8 @@ static void exynos_pm_enter_sleep_mode(void)
static void exynos_pm_prepare(void)
{
exynos_set_delayed_reset_assertion(false);
/* Set wake-up mask registers */
exynos_pm_set_wakeup_mask();
......@@ -482,6 +484,7 @@ static void exynos_pm_resume(void)
/* Clear SLEEP mode set in INFORM1 */
pmu_raw_writel(0x0, S5P_INFORM1);
exynos_set_delayed_reset_assertion(true);
}
static void exynos3250_pm_resume(void)
......@@ -723,8 +726,10 @@ void __init exynos_pm_init(void)
return;
}
if (WARN_ON(!of_find_property(np, "interrupt-controller", NULL)))
if (WARN_ON(!of_find_property(np, "interrupt-controller", NULL))) {
pr_warn("Outdated DT detected, suspend/resume will NOT work\n");
return;
}
pm_data = (const struct exynos_pm_data *) match->data;
......
arch/arm/mach-gemini/common.h
浏览文件 @ 909eacd7
......@@ -12,6 +12,8 @@
#ifndef __GEMINI_COMMON_H__
#define __GEMINI_COMMON_H__
#include <linux/reboot.h>
struct mtd_partition;
extern void gemini_map_io(void);
......@@ -26,6 +28,6 @@ extern int platform_register_pflash(unsigned int size,
struct mtd_partition *parts,
unsigned int nr_parts);
extern void gemini_restart(char mode, const char *cmd);
extern void gemini_restart(enum reboot_mode mode, const char *cmd);
#endif /* __GEMINI_COMMON_H__ */
arch/arm/mach-gemini/reset.c
浏览文件 @ 909eacd7
......@@ -14,7 +14,9 @@
#include <mach/hardware.h>
#include <mach/global_reg.h>
void gemini_restart(char mode, const char *cmd)
#include "common.h"
void gemini_restart(enum reboot_mode mode, const char *cmd)
{
__raw_writel(RESET_GLOBAL | RESET_CPU1,
IO_ADDRESS(GEMINI_GLOBAL_BASE) + GLOBAL_RESET);
......
arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c
浏览文件 @ 909eacd7
/*
* Copyright (C) 2010 Pengutronix, Wolfram Sang <w.sang@pengutronix.de>
* Copyright (C) 2010 Pengutronix, Wolfram Sang <kernel@pengutronix.de>
*
* This program is free software; you can redistribute it and/or modify it under
* the terms of the GNU General Public License version 2 as published by the
......
arch/arm/mach-omap2/omap_hwmod.c
浏览文件 @ 909eacd7
......@@ -171,6 +171,12 @@
*/
#define LINKS_PER_OCP_IF 2
/*
* Address offset (in bytes) between the reset control and the reset
* status registers: 4 bytes on OMAP4
*/
#define OMAP4_RST_CTRL_ST_OFFSET 4
/**
* struct omap_hwmod_soc_ops - fn ptrs for some SoC-specific operations
* @enable_module: function to enable a module (via MODULEMODE)
......@@ -3016,10 +3022,12 @@ static int _omap4_deassert_hardreset(struct omap_hwmod *oh,
if (ohri->st_shift)
pr_err("omap_hwmod: %s: %s: hwmod data error: OMAP4 does not support st_shift\n",
oh->name, ohri->name);
return omap_prm_deassert_hardreset(ohri->rst_shift, 0,
return omap_prm_deassert_hardreset(ohri->rst_shift, ohri->rst_shift,
oh->clkdm->pwrdm.ptr->prcm_partition,
oh->clkdm->pwrdm.ptr->prcm_offs,
oh->prcm.omap4.rstctrl_offs, 0);
oh->prcm.omap4.rstctrl_offs,
oh->prcm.omap4.rstctrl_offs +
OMAP4_RST_CTRL_ST_OFFSET);
}
/**
......@@ -3047,27 +3055,6 @@ static int _omap4_is_hardreset_asserted(struct omap_hwmod *oh,
oh->prcm.omap4.rstctrl_offs);
}
/**
* _am33xx_assert_hardreset - call AM33XX PRM hardreset fn with hwmod args
* @oh: struct omap_hwmod * to assert hardreset
* @ohri: hardreset line data
*
* Call am33xx_prminst_assert_hardreset() with parameters extracted
* from the hwmod @oh and the hardreset line data @ohri. Only
* intended for use as an soc_ops function pointer. Passes along the
* return value from am33xx_prminst_assert_hardreset(). XXX This
* function is scheduled for removal when the PRM code is moved into
* drivers/.
*/
static int _am33xx_assert_hardreset(struct omap_hwmod *oh,
struct omap_hwmod_rst_info *ohri)
{
return omap_prm_assert_hardreset(ohri->rst_shift, 0,
oh->clkdm->pwrdm.ptr->prcm_offs,
oh->prcm.omap4.rstctrl_offs);
}
/**
* _am33xx_deassert_hardreset - call AM33XX PRM hardreset fn with hwmod args
* @oh: struct omap_hwmod * to deassert hardreset
......@@ -3083,32 +3070,13 @@ static int _am33xx_assert_hardreset(struct omap_hwmod *oh,
static int _am33xx_deassert_hardreset(struct omap_hwmod *oh,
struct omap_hwmod_rst_info *ohri)
{
return omap_prm_deassert_hardreset(ohri->rst_shift, ohri->st_shift, 0,
return omap_prm_deassert_hardreset(ohri->rst_shift, ohri->st_shift,
oh->clkdm->pwrdm.ptr->prcm_partition,
oh->clkdm->pwrdm.ptr->prcm_offs,
oh->prcm.omap4.rstctrl_offs,
oh->prcm.omap4.rstst_offs);
}
/**
* _am33xx_is_hardreset_asserted - call AM33XX PRM hardreset fn with hwmod args
* @oh: struct omap_hwmod * to test hardreset
* @ohri: hardreset line data
*
* Call am33xx_prminst_is_hardreset_asserted() with parameters
* extracted from the hwmod @oh and the hardreset line data @ohri.
* Only intended for use as an soc_ops function pointer. Passes along
* the return value from am33xx_prminst_is_hardreset_asserted(). XXX
* This function is scheduled for removal when the PRM code is moved
* into drivers/.
*/
static int _am33xx_is_hardreset_asserted(struct omap_hwmod *oh,
struct omap_hwmod_rst_info *ohri)
{
return omap_prm_is_hardreset_asserted(ohri->rst_shift, 0,
oh->clkdm->pwrdm.ptr->prcm_offs,
oh->prcm.omap4.rstctrl_offs);
}
/* Public functions */
u32 omap_hwmod_read(struct omap_hwmod *oh, u16 reg_offs)
......@@ -3908,21 +3876,13 @@ void __init omap_hwmod_init(void)
soc_ops.init_clkdm = _init_clkdm;
soc_ops.update_context_lost = _omap4_update_context_lost;
soc_ops.get_context_lost = _omap4_get_context_lost;
} else if (soc_is_am43xx()) {
} else if (cpu_is_ti816x() || soc_is_am33xx() || soc_is_am43xx()) {
soc_ops.enable_module = _omap4_enable_module;
soc_ops.disable_module = _omap4_disable_module;
soc_ops.wait_target_ready = _omap4_wait_target_ready;
soc_ops.assert_hardreset = _omap4_assert_hardreset;
soc_ops.deassert_hardreset = _omap4_deassert_hardreset;
soc_ops.is_hardreset_asserted = _omap4_is_hardreset_asserted;
soc_ops.init_clkdm = _init_clkdm;
} else if (cpu_is_ti816x() || soc_is_am33xx()) {
soc_ops.enable_module = _omap4_enable_module;
soc_ops.disable_module = _omap4_disable_module;
soc_ops.wait_target_ready = _omap4_wait_target_ready;
soc_ops.assert_hardreset = _am33xx_assert_hardreset;
soc_ops.deassert_hardreset = _am33xx_deassert_hardreset;
soc_ops.is_hardreset_asserted = _am33xx_is_hardreset_asserted;
soc_ops.is_hardreset_asserted = _omap4_is_hardreset_asserted;
soc_ops.init_clkdm = _init_clkdm;
} else {
WARN(1, "omap_hwmod: unknown SoC type\n");
......
arch/arm/mach-omap2/omap_hwmod_43xx_data.c
浏览文件 @ 909eacd7
......@@ -544,6 +544,44 @@ static struct omap_hwmod am43xx_hdq1w_hwmod = {
},
};
static struct omap_hwmod_class_sysconfig am43xx_vpfe_sysc = {
.rev_offs = 0x0,
.sysc_offs = 0x104,
.sysc_flags = SYSC_HAS_MIDLEMODE | SYSC_HAS_SIDLEMODE,
.idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
MSTANDBY_FORCE | MSTANDBY_SMART | MSTANDBY_NO),
.sysc_fields = &omap_hwmod_sysc_type2,
};
static struct omap_hwmod_class am43xx_vpfe_hwmod_class = {
.name = "vpfe",
.sysc = &am43xx_vpfe_sysc,
};
static struct omap_hwmod am43xx_vpfe0_hwmod = {
.name = "vpfe0",
.class = &am43xx_vpfe_hwmod_class,
.clkdm_name = "l3s_clkdm",
.prcm = {
.omap4 = {
.modulemode = MODULEMODE_SWCTRL,
.clkctrl_offs = AM43XX_CM_PER_VPFE0_CLKCTRL_OFFSET,
},
},
};
static struct omap_hwmod am43xx_vpfe1_hwmod = {
.name = "vpfe1",
.class = &am43xx_vpfe_hwmod_class,
.clkdm_name = "l3s_clkdm",
.prcm = {
.omap4 = {
.modulemode = MODULEMODE_SWCTRL,
.clkctrl_offs = AM43XX_CM_PER_VPFE1_CLKCTRL_OFFSET,
},
},
};
/* Interfaces */
static struct omap_hwmod_ocp_if am43xx_l3_main__l4_hs = {
.master = &am33xx_l3_main_hwmod,
......@@ -825,6 +863,34 @@ static struct omap_hwmod_ocp_if am43xx_l4_ls__hdq1w = {
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
static struct omap_hwmod_ocp_if am43xx_l3__vpfe0 = {
.master = &am43xx_vpfe0_hwmod,
.slave = &am33xx_l3_main_hwmod,
.clk = "l3_gclk",
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
static struct omap_hwmod_ocp_if am43xx_l3__vpfe1 = {
.master = &am43xx_vpfe1_hwmod,
.slave = &am33xx_l3_main_hwmod,
.clk = "l3_gclk",
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
static struct omap_hwmod_ocp_if am43xx_l4_ls__vpfe0 = {
.master = &am33xx_l4_ls_hwmod,
.slave = &am43xx_vpfe0_hwmod,
.clk = "l4ls_gclk",
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
static struct omap_hwmod_ocp_if am43xx_l4_ls__vpfe1 = {
.master = &am33xx_l4_ls_hwmod,
.slave = &am43xx_vpfe1_hwmod,
.clk = "l4ls_gclk",
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
static struct omap_hwmod_ocp_if *am43xx_hwmod_ocp_ifs[] __initdata = {
&am33xx_l4_wkup__synctimer,
&am43xx_l4_ls__timer8,
......@@ -925,6 +991,10 @@ static struct omap_hwmod_ocp_if *am43xx_hwmod_ocp_ifs[] __initdata = {
&am43xx_l4_ls__dss_dispc,
&am43xx_l4_ls__dss_rfbi,
&am43xx_l4_ls__hdq1w,
&am43xx_l3__vpfe0,
&am43xx_l3__vpfe1,
&am43xx_l4_ls__vpfe0,
&am43xx_l4_ls__vpfe1,
NULL,
};
......
arch/arm/mach-omap2/prcm43xx.h
浏览文件 @ 909eacd7
......@@ -144,5 +144,6 @@
#define AM43XX_CM_PER_USBPHYOCP2SCP1_CLKCTRL_OFFSET 0x05C0
#define AM43XX_CM_PER_DSS_CLKCTRL_OFFSET 0x0a20
#define AM43XX_CM_PER_HDQ1W_CLKCTRL_OFFSET 0x04a0
#define AM43XX_CM_PER_VPFE0_CLKCTRL_OFFSET 0x0068
#define AM43XX_CM_PER_VPFE1_CLKCTRL_OFFSET 0x0070
#endif
arch/arm/mach-omap2/prm-regbits-34xx.h
浏览文件 @ 909eacd7
......@@ -112,6 +112,7 @@
#define OMAP3430_VC_CMD_ONLP_SHIFT 16
#define OMAP3430_VC_CMD_RET_SHIFT 8
#define OMAP3430_VC_CMD_OFF_SHIFT 0
#define OMAP3430_SREN_MASK (1 << 4)
#define OMAP3430_HSEN_MASK (1 << 3)
#define OMAP3430_MCODE_MASK (0x7 << 0)
#define OMAP3430_VALID_MASK (1 << 24)
......
arch/arm/mach-omap2/prm-regbits-44xx.h
浏览文件 @ 909eacd7
......@@ -35,6 +35,7 @@
#define OMAP4430_GLOBAL_WARM_SW_RST_SHIFT 1
#define OMAP4430_GLOBAL_WUEN_MASK (1 << 16)
#define OMAP4430_HSMCODE_MASK (0x7 << 0)
#define OMAP4430_SRMODEEN_MASK (1 << 4)
#define OMAP4430_HSMODEEN_MASK (1 << 3)
#define OMAP4430_HSSCLL_SHIFT 24
#define OMAP4430_ICEPICK_RST_SHIFT 9
......
arch/arm/mach-omap2/prminst44xx.c
浏览文件 @ 909eacd7
......@@ -87,12 +87,6 @@ u32 omap4_prminst_rmw_inst_reg_bits(u32 mask, u32 bits, u8 part, s16 inst,
return v;
}
/*
* Address offset (in bytes) between the reset control and the reset
* status registers: 4 bytes on OMAP4
*/
#define OMAP4_RST_CTRL_ST_OFFSET 4
/**
* omap4_prminst_is_hardreset_asserted - read the HW reset line state of
* submodules contained in the hwmod module
......@@ -141,11 +135,11 @@ int omap4_prminst_assert_hardreset(u8 shift, u8 part, s16 inst,
* omap4_prminst_deassert_hardreset - deassert a submodule hardreset line and
* wait
* @shift: register bit shift corresponding to the reset line to deassert
* @st_shift: status bit offset, not used for OMAP4+
* @st_shift: status bit offset corresponding to the reset line
* @part: PRM partition
* @inst: PRM instance offset
* @rstctrl_offs: reset register offset
* @st_offs: reset status register offset, not used for OMAP4+
* @rstst_offs: reset status register offset
*
* Some IPs like dsp, ipu or iva contain processors that require an HW
* reset line to be asserted / deasserted in order to fully enable the
......@@ -157,11 +151,11 @@ int omap4_prminst_assert_hardreset(u8 shift, u8 part, s16 inst,
* of reset, or -EBUSY if the submodule did not exit reset promptly.
*/
int omap4_prminst_deassert_hardreset(u8 shift, u8 st_shift, u8 part, s16 inst,
u16 rstctrl_offs, u16 st_offs)
u16 rstctrl_offs, u16 rstst_offs)
{
int c;
u32 mask = 1 << shift;
u16 rstst_offs = rstctrl_offs + OMAP4_RST_CTRL_ST_OFFSET;
u32 st_mask = 1 << st_shift;
/* Check the current status to avoid de-asserting the line twice */
if (omap4_prminst_is_hardreset_asserted(shift, part, inst,
......@@ -169,13 +163,13 @@ int omap4_prminst_deassert_hardreset(u8 shift, u8 st_shift, u8 part, s16 inst,
return -EEXIST;
/* Clear the reset status by writing 1 to the status bit */
omap4_prminst_rmw_inst_reg_bits(0xffffffff, mask, part, inst,
omap4_prminst_rmw_inst_reg_bits(0xffffffff, st_mask, part, inst,
rstst_offs);
/* de-assert the reset control line */
omap4_prminst_rmw_inst_reg_bits(mask, 0, part, inst, rstctrl_offs);
/* wait the status to be set */
omap_test_timeout(omap4_prminst_is_hardreset_asserted(shift, part, inst,
rstst_offs),
omap_test_timeout(omap4_prminst_is_hardreset_asserted(st_shift, part,
inst, rstst_offs),
MAX_MODULE_HARDRESET_WAIT, c);
return (c == MAX_MODULE_HARDRESET_WAIT) ? -EBUSY : 0;
......
arch/arm/mach-omap2/timer.c
浏览文件 @ 909eacd7
......@@ -298,14 +298,11 @@ static int __init omap_dm_timer_init_one(struct omap_dm_timer *timer,
if (IS_ERR(src))
return PTR_ERR(src);
if (clk_get_parent(timer->fclk) != src) {
r = clk_set_parent(timer->fclk, src);
if (r < 0) {
pr_warn("%s: %s cannot set source\n", __func__,
oh->name);
clk_put(src);
return r;
}
r = clk_set_parent(timer->fclk, src);
if (r < 0) {
pr_warn("%s: %s cannot set source\n", __func__, oh->name);
clk_put(src);
return r;
}
clk_put(src);
......
arch/arm/mach-omap2/vc.c
浏览文件 @ 909eacd7
......@@ -316,7 +316,8 @@ static void __init omap3_vc_init_pmic_signaling(struct voltagedomain *voltdm)
* idle. And we can also scale voltages to zero for off-idle.
* Note that no actual voltage scaling during off-idle will
* happen unless the board specific twl4030 PMIC scripts are
* loaded.
* loaded. See also omap_vc_i2c_init for comments regarding
* erratum i531.
*/
val = voltdm->read(OMAP3_PRM_VOLTCTRL_OFFSET);
if (!(val & OMAP3430_PRM_VOLTCTRL_SEL_OFF)) {
......@@ -704,9 +705,16 @@ static void __init omap_vc_i2c_init(struct voltagedomain *voltdm)
return;
}
/*
* Note that for omap3 OMAP3430_SREN_MASK clears SREN to work around
* erratum i531 "Extra Power Consumed When Repeated Start Operation
* Mode Is Enabled on I2C Interface Dedicated for Smart Reflex (I2C4)".
* Otherwise I2C4 eventually leads into about 23mW extra power being
* consumed even during off idle using VMODE.
*/
i2c_high_speed = voltdm->pmic->i2c_high_speed;
if (i2c_high_speed)
voltdm->rmw(vc->common->i2c_cfg_hsen_mask,
voltdm->rmw(vc->common->i2c_cfg_clear_mask,
vc->common->i2c_cfg_hsen_mask,
vc->common->i2c_cfg_reg);
......
arch/arm/mach-omap2/vc.h
浏览文件 @ 909eacd7
......@@ -34,6 +34,7 @@ struct voltagedomain;
* @cmd_ret_shift: RET field shift in PRM_VC_CMD_VAL_* register
* @cmd_off_shift: OFF field shift in PRM_VC_CMD_VAL_* register
* @i2c_cfg_reg: I2C configuration register offset
* @i2c_cfg_clear_mask: high-speed mode bit clear mask in I2C config register
* @i2c_cfg_hsen_mask: high-speed mode bit field mask in I2C config register
* @i2c_mcode_mask: MCODE field mask for I2C config register
*
......@@ -52,6 +53,7 @@ struct omap_vc_common {
u8 cmd_ret_shift;
u8 cmd_off_shift;
u8 i2c_cfg_reg;
u8 i2c_cfg_clear_mask;
u8 i2c_cfg_hsen_mask;
u8 i2c_mcode_mask;
};
......
arch/arm/mach-omap2/vc3xxx_data.c
浏览文件 @ 909eacd7
......@@ -40,6 +40,7 @@ static struct omap_vc_common omap3_vc_common = {
.cmd_onlp_shift = OMAP3430_VC_CMD_ONLP_SHIFT,
.cmd_ret_shift = OMAP3430_VC_CMD_RET_SHIFT,
.cmd_off_shift = OMAP3430_VC_CMD_OFF_SHIFT,
.i2c_cfg_clear_mask = OMAP3430_SREN_MASK | OMAP3430_HSEN_MASK,
.i2c_cfg_hsen_mask = OMAP3430_HSEN_MASK,
.i2c_cfg_reg = OMAP3_PRM_VC_I2C_CFG_OFFSET,
.i2c_mcode_mask = OMAP3430_MCODE_MASK,
......
arch/arm/mach-omap2/vc44xx_data.c
浏览文件 @ 909eacd7
......@@ -42,6 +42,7 @@ static const struct omap_vc_common omap4_vc_common = {
.cmd_ret_shift = OMAP4430_RET_SHIFT,
.cmd_off_shift = OMAP4430_OFF_SHIFT,
.i2c_cfg_reg = OMAP4_PRM_VC_CFG_I2C_MODE_OFFSET,
.i2c_cfg_clear_mask = OMAP4430_SRMODEEN_MASK | OMAP4430_HSMODEEN_MASK,
.i2c_cfg_hsen_mask = OMAP4430_HSMODEEN_MASK,
.i2c_mcode_mask = OMAP4430_HSMCODE_MASK,
};
......
arch/arm/mach-pxa/Kconfig
浏览文件 @ 909eacd7
......@@ -691,4 +691,13 @@ config SHARPSL_PM_MAX1111
config PXA310_ULPI
bool
config PXA_SYSTEMS_CPLDS
tristate "Motherboard cplds"
default ARCH_LUBBOCK || MACH_MAINSTONE
help
This driver supports the Lubbock and Mainstone multifunction chip
found on the pxa25x development platform system (Lubbock) and pxa27x
development platform system (Mainstone). This IO board supports the
interrupts handling, ethernet controller, flash chips, etc ...
endif
arch/arm/mach-pxa/Makefile
浏览文件 @ 909eacd7
......@@ -90,4 +90,5 @@ obj-$(CONFIG_MACH_RAUMFELD_CONNECTOR) += raumfeld.o
obj-$(CONFIG_MACH_RAUMFELD_SPEAKER) += raumfeld.o
obj-$(CONFIG_MACH_ZIPIT2) += z2.o
obj-$(CONFIG_PXA_SYSTEMS_CPLDS) += pxa_cplds_irqs.o
obj-$(CONFIG_TOSA_BT) += tosa-bt.o
arch/arm/mach-pxa/include/mach/lubbock.h
浏览文件 @ 909eacd7
......@@ -37,7 +37,9 @@
#define LUB_GP __LUB_REG(LUBBOCK_FPGA_PHYS + 0x100)
/* Board specific IRQs */
#define LUBBOCK_IRQ(x) (IRQ_BOARD_START + (x))
#define LUBBOCK_NR_IRQS IRQ_BOARD_START
#define LUBBOCK_IRQ(x) (LUBBOCK_NR_IRQS + (x))
#define LUBBOCK_SD_IRQ LUBBOCK_IRQ(0)
#define LUBBOCK_SA1111_IRQ LUBBOCK_IRQ(1)
#define LUBBOCK_USB_IRQ LUBBOCK_IRQ(2) /* usb connect */
......@@ -47,8 +49,7 @@
#define LUBBOCK_USB_DISC_IRQ LUBBOCK_IRQ(6) /* usb disconnect */
#define LUBBOCK_LAST_IRQ LUBBOCK_IRQ(6)
#define LUBBOCK_SA1111_IRQ_BASE (IRQ_BOARD_START + 16)
#define LUBBOCK_NR_IRQS (IRQ_BOARD_START + 16 + 55)
#define LUBBOCK_SA1111_IRQ_BASE (LUBBOCK_NR_IRQS + 32)
#ifndef __ASSEMBLY__
extern void lubbock_set_misc_wr(unsigned int mask, unsigned int set);
......
arch/arm/mach-pxa/include/mach/mainstone.h
浏览文件 @ 909eacd7
......@@ -120,7 +120,9 @@
#define MST_PCMCIA_PWR_VCC_50 0x4 /* voltage VCC = 5.0V */
/* board specific IRQs */
#define MAINSTONE_IRQ(x) (IRQ_BOARD_START + (x))
#define MAINSTONE_NR_IRQS IRQ_BOARD_START
#define MAINSTONE_IRQ(x) (MAINSTONE_NR_IRQS + (x))
#define MAINSTONE_MMC_IRQ MAINSTONE_IRQ(0)
#define MAINSTONE_USIM_IRQ MAINSTONE_IRQ(1)
#define MAINSTONE_USBC_IRQ MAINSTONE_IRQ(2)
......@@ -136,6 +138,4 @@
#define MAINSTONE_S1_STSCHG_IRQ MAINSTONE_IRQ(14)
#define MAINSTONE_S1_IRQ MAINSTONE_IRQ(15)
#define MAINSTONE_NR_IRQS (IRQ_BOARD_START + 16)
#endif
arch/arm/mach-pxa/lubbock.c
浏览文件 @ 909eacd7
......@@ -12,6 +12,7 @@
* published by the Free Software Foundation.
*/
#include <linux/gpio.h>
#include <linux/gpio/machine.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
......@@ -123,84 +124,6 @@ void lubbock_set_misc_wr(unsigned int mask, unsigned int set)
}
EXPORT_SYMBOL(lubbock_set_misc_wr);
static unsigned long lubbock_irq_enabled;
static void lubbock_mask_irq(struct irq_data *d)
{
int lubbock_irq = (d->irq - LUBBOCK_IRQ(0));
LUB_IRQ_MASK_EN = (lubbock_irq_enabled &= ~(1 << lubbock_irq));
}
static void lubbock_unmask_irq(struct irq_data *d)
{
int lubbock_irq = (d->irq - LUBBOCK_IRQ(0));
/* the irq can be acknowledged only if deasserted, so it's done here */
LUB_IRQ_SET_CLR &= ~(1 << lubbock_irq);
LUB_IRQ_MASK_EN = (lubbock_irq_enabled |= (1 << lubbock_irq));
}
static struct irq_chip lubbock_irq_chip = {
.name = "FPGA",
.irq_ack = lubbock_mask_irq,
.irq_mask = lubbock_mask_irq,
.irq_unmask = lubbock_unmask_irq,
};
static void lubbock_irq_handler(unsigned int irq, struct irq_desc *desc)
{
unsigned long pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled;
do {
/* clear our parent irq */
desc->irq_data.chip->irq_ack(&desc->irq_data);
if (likely(pending)) {
irq = LUBBOCK_IRQ(0) + __ffs(pending);
generic_handle_irq(irq);
}
pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled;
} while (pending);
}
static void __init lubbock_init_irq(void)
{
int irq;
pxa25x_init_irq();
/* setup extra lubbock irqs */
for (irq = LUBBOCK_IRQ(0); irq <= LUBBOCK_LAST_IRQ; irq++) {
irq_set_chip_and_handler(irq, &lubbock_irq_chip,
handle_level_irq);
set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
}
irq_set_chained_handler(PXA_GPIO_TO_IRQ(0), lubbock_irq_handler);
irq_set_irq_type(PXA_GPIO_TO_IRQ(0), IRQ_TYPE_EDGE_FALLING);
}
#ifdef CONFIG_PM
static void lubbock_irq_resume(void)
{
LUB_IRQ_MASK_EN = lubbock_irq_enabled;
}
static struct syscore_ops lubbock_irq_syscore_ops = {
.resume = lubbock_irq_resume,
};
static int __init lubbock_irq_device_init(void)
{
if (machine_is_lubbock()) {
register_syscore_ops(&lubbock_irq_syscore_ops);
return 0;
}
return -ENODEV;
}
device_initcall(lubbock_irq_device_init);
#endif
static int lubbock_udc_is_connected(void)
{
return (LUB_MISC_RD & (1 << 9)) == 0;
......@@ -383,11 +306,38 @@ static struct platform_device lubbock_flash_device[2] = {
},
};
static struct resource lubbock_cplds_resources[] = {
[0] = {
.start = LUBBOCK_FPGA_PHYS + 0xc0,
.end = LUBBOCK_FPGA_PHYS + 0xe0 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = PXA_GPIO_TO_IRQ(0),
.end = PXA_GPIO_TO_IRQ(0),
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
},
[2] = {
.start = LUBBOCK_IRQ(0),
.end = LUBBOCK_IRQ(6),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device lubbock_cplds_device = {
.name = "pxa_cplds_irqs",
.id = -1,
.resource = &lubbock_cplds_resources[0],
.num_resources = 3,
};
static struct platform_device *devices[] __initdata = {
&sa1111_device,
&smc91x_device,
&lubbock_flash_device[0],
&lubbock_flash_device[1],
&lubbock_cplds_device,
};
static struct pxafb_mode_info sharp_lm8v31_mode = {
......@@ -648,7 +598,7 @@ MACHINE_START(LUBBOCK, "Intel DBPXA250 Development Platform (aka Lubbock)")
/* Maintainer: MontaVista Software Inc. */
.map_io = lubbock_map_io,
.nr_irqs = LUBBOCK_NR_IRQS,
.init_irq = lubbock_init_irq,
.init_irq = pxa25x_init_irq,
.handle_irq = pxa25x_handle_irq,
.init_time = pxa_timer_init,
.init_machine = lubbock_init,
......
arch/arm/mach-pxa/mainstone.c
浏览文件 @ 909eacd7
......@@ -13,6 +13,7 @@
* published by the Free Software Foundation.
*/
#include <linux/gpio.h>
#include <linux/gpio/machine.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/syscore_ops.h>
......@@ -122,92 +123,6 @@ static unsigned long mainstone_pin_config[] = {
GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH,
};
static unsigned long mainstone_irq_enabled;
static void mainstone_mask_irq(struct irq_data *d)
{
int mainstone_irq = (d->irq - MAINSTONE_IRQ(0));
MST_INTMSKENA = (mainstone_irq_enabled &= ~(1 << mainstone_irq));
}
static void mainstone_unmask_irq(struct irq_data *d)
{
int mainstone_irq = (d->irq - MAINSTONE_IRQ(0));
/* the irq can be acknowledged only if deasserted, so it's done here */
MST_INTSETCLR &= ~(1 << mainstone_irq);
MST_INTMSKENA = (mainstone_irq_enabled |= (1 << mainstone_irq));
}
static struct irq_chip mainstone_irq_chip = {
.name = "FPGA",
.irq_ack = mainstone_mask_irq,
.irq_mask = mainstone_mask_irq,
.irq_unmask = mainstone_unmask_irq,
};
static void mainstone_irq_handler(unsigned int irq, struct irq_desc *desc)
{
unsigned long pending = MST_INTSETCLR & mainstone_irq_enabled;
do {
/* clear useless edge notification */
desc->irq_data.chip->irq_ack(&desc->irq_data);
if (likely(pending)) {
irq = MAINSTONE_IRQ(0) + __ffs(pending);
generic_handle_irq(irq);
}
pending = MST_INTSETCLR & mainstone_irq_enabled;
} while (pending);
}
static void __init mainstone_init_irq(void)
{
int irq;
pxa27x_init_irq();
/* setup extra Mainstone irqs */
for(irq = MAINSTONE_IRQ(0); irq <= MAINSTONE_IRQ(15); irq++) {
irq_set_chip_and_handler(irq, &mainstone_irq_chip,
handle_level_irq);
if (irq == MAINSTONE_IRQ(10) || irq == MAINSTONE_IRQ(14))
set_irq_flags(irq, IRQF_VALID | IRQF_PROBE | IRQF_NOAUTOEN);
else
set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
}
set_irq_flags(MAINSTONE_IRQ(8), 0);
set_irq_flags(MAINSTONE_IRQ(12), 0);
MST_INTMSKENA = 0;
MST_INTSETCLR = 0;
irq_set_chained_handler(PXA_GPIO_TO_IRQ(0), mainstone_irq_handler);
irq_set_irq_type(PXA_GPIO_TO_IRQ(0), IRQ_TYPE_EDGE_FALLING);
}
#ifdef CONFIG_PM
static void mainstone_irq_resume(void)
{
MST_INTMSKENA = mainstone_irq_enabled;
}
static struct syscore_ops mainstone_irq_syscore_ops = {
.resume = mainstone_irq_resume,
};
static int __init mainstone_irq_device_init(void)
{
if (machine_is_mainstone())
register_syscore_ops(&mainstone_irq_syscore_ops);
return 0;
}
device_initcall(mainstone_irq_device_init);
#endif
static struct resource smc91x_resources[] = {
[0] = {
.start = (MST_ETH_PHYS + 0x300),
......@@ -487,11 +402,37 @@ static struct platform_device mst_gpio_keys_device = {
},
};
static struct resource mst_cplds_resources[] = {
[0] = {
.start = MST_FPGA_PHYS + 0xc0,
.end = MST_FPGA_PHYS + 0xe0 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = PXA_GPIO_TO_IRQ(0),
.end = PXA_GPIO_TO_IRQ(0),
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
},
[2] = {
.start = MAINSTONE_IRQ(0),
.end = MAINSTONE_IRQ(15),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device mst_cplds_device = {
.name = "pxa_cplds_irqs",
.id = -1,
.resource = &mst_cplds_resources[0],
.num_resources = 3,
};
static struct platform_device *platform_devices[] __initdata = {
&smc91x_device,
&mst_flash_device[0],
&mst_flash_device[1],
&mst_gpio_keys_device,
&mst_cplds_device,
};
static struct pxaohci_platform_data mainstone_ohci_platform_data = {
......@@ -718,7 +659,7 @@ MACHINE_START(MAINSTONE, "Intel HCDDBBVA0 Development Platform (aka Mainstone)")
.atag_offset = 0x100, /* BLOB boot parameter setting */
.map_io = mainstone_map_io,
.nr_irqs = MAINSTONE_NR_IRQS,
.init_irq = mainstone_init_irq,
.init_irq = pxa27x_init_irq,
.handle_irq = pxa27x_handle_irq,
.init_time = pxa_timer_init,
.init_machine = mainstone_init,
......
arch/arm/mach-pxa/pxa_cplds_irqs.c 0 → 100644
浏览文件 @ 909eacd7
/*
* Intel Reference Systems cplds
*
* Copyright (C) 2014 Robert Jarzmik
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* Cplds motherboard driver, supporting lubbock and mainstone SoC board.
*/
#include <linux/bitops.h>
#include <linux/gpio.h>
#include <linux/gpio/consumer.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/irqdomain.h>
#include <linux/mfd/core.h>
#include <linux/module.h>
#include <linux/of_platform.h>
#define FPGA_IRQ_MASK_EN 0x0
#define FPGA_IRQ_SET_CLR 0x10
#define CPLDS_NB_IRQ 32
struct cplds {
void __iomem *base;
int irq;
unsigned int irq_mask;
struct gpio_desc *gpio0;
struct irq_domain *irqdomain;
};
static irqreturn_t cplds_irq_handler(int in_irq, void *d)
{
struct cplds *fpga = d;
unsigned long pending;
unsigned int bit;
pending = readl(fpga->base + FPGA_IRQ_SET_CLR) & fpga->irq_mask;
for_each_set_bit(bit, &pending, CPLDS_NB_IRQ)
generic_handle_irq(irq_find_mapping(fpga->irqdomain, bit));
return IRQ_HANDLED;
}
static void cplds_irq_mask_ack(struct irq_data *d)
{
struct cplds *fpga = irq_data_get_irq_chip_data(d);
unsigned int cplds_irq = irqd_to_hwirq(d);
unsigned int set, bit = BIT(cplds_irq);
fpga->irq_mask &= ~bit;
writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN);
set = readl(fpga->base + FPGA_IRQ_SET_CLR);
writel(set & ~bit, fpga->base + FPGA_IRQ_SET_CLR);
}
static void cplds_irq_unmask(struct irq_data *d)
{
struct cplds *fpga = irq_data_get_irq_chip_data(d);
unsigned int cplds_irq = irqd_to_hwirq(d);
unsigned int bit = BIT(cplds_irq);
fpga->irq_mask |= bit;
writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN);
}
static struct irq_chip cplds_irq_chip = {
.name = "pxa_cplds",
.irq_mask_ack = cplds_irq_mask_ack,
.irq_unmask = cplds_irq_unmask,
.flags = IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_SKIP_SET_WAKE,
};
static int cplds_irq_domain_map(struct irq_domain *d, unsigned int irq,
irq_hw_number_t hwirq)
{
struct cplds *fpga = d->host_data;
irq_set_chip_and_handler(irq, &cplds_irq_chip, handle_level_irq);
irq_set_chip_data(irq, fpga);
return 0;
}
static const struct irq_domain_ops cplds_irq_domain_ops = {
.xlate = irq_domain_xlate_twocell,
.map = cplds_irq_domain_map,
};
static int cplds_resume(struct platform_device *pdev)
{
struct cplds *fpga = platform_get_drvdata(pdev);
writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN);
return 0;
}
static int cplds_probe(struct platform_device *pdev)
{
struct resource *res;
struct cplds *fpga;
int ret;
unsigned int base_irq = 0;
unsigned long irqflags = 0;
fpga = devm_kzalloc(&pdev->dev, sizeof(*fpga), GFP_KERNEL);
if (!fpga)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
if (res) {
fpga->irq = (unsigned int)res->start;
irqflags = res->flags;
}
if (!fpga->irq)
return -ENODEV;
base_irq = platform_get_irq(pdev, 1);
if (base_irq < 0)
base_irq = 0;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
fpga->base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(fpga->base))
return PTR_ERR(fpga->base);
platform_set_drvdata(pdev, fpga);
writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN);
writel(0, fpga->base + FPGA_IRQ_SET_CLR);
ret = devm_request_irq(&pdev->dev, fpga->irq, cplds_irq_handler,
irqflags, dev_name(&pdev->dev), fpga);
if (ret == -ENOSYS)
return -EPROBE_DEFER;
if (ret) {
dev_err(&pdev->dev, "couldn't request main irq%d: %d\n",
fpga->irq, ret);
return ret;
}
irq_set_irq_wake(fpga->irq, 1);
fpga->irqdomain = irq_domain_add_linear(pdev->dev.of_node,
CPLDS_NB_IRQ,
&cplds_irq_domain_ops, fpga);
if (!fpga->irqdomain)
return -ENODEV;
if (base_irq) {
ret = irq_create_strict_mappings(fpga->irqdomain, base_irq, 0,
CPLDS_NB_IRQ);
if (ret) {
dev_err(&pdev->dev, "couldn't create the irq mapping %d..%d\n",
base_irq, base_irq + CPLDS_NB_IRQ);
return ret;
}
}
return 0;
}
static int cplds_remove(struct platform_device *pdev)
{
struct cplds *fpga = platform_get_drvdata(pdev);
irq_set_chip_and_handler(fpga->irq, NULL, NULL);
return 0;
}
static const struct of_device_id cplds_id_table[] = {
{ .compatible = "intel,lubbock-cplds-irqs", },
{ .compatible = "intel,mainstone-cplds-irqs", },
{ }
};
MODULE_DEVICE_TABLE(of, cplds_id_table);
static struct platform_driver cplds_driver = {
.driver = {
.name = "pxa_cplds_irqs",
.of_match_table = of_match_ptr(cplds_id_table),
},
.probe = cplds_probe,
.remove = cplds_remove,
.resume = cplds_resume,
};
module_platform_driver(cplds_driver);
MODULE_DESCRIPTION("PXA Cplds interrupts driver");
MODULE_AUTHOR("Robert Jarzmik <robert.jarzmik@free.fr>");
MODULE_LICENSE("GPL");
arch/arm/mach-rockchip/pm.c
浏览文件 @ 909eacd7
......@@ -83,6 +83,13 @@ static void rk3288_slp_mode_set(int level)
SGRF_PCLK_WDT_GATE | SGRF_FAST_BOOT_EN
| SGRF_PCLK_WDT_GATE_WRITE | SGRF_FAST_BOOT_EN_WRITE);
/*
* The dapswjdp can not auto reset before resume, that cause it may
* access some illegal address during resume. Let's disable it before
* suspend, and the MASKROM will enable it back.
*/
regmap_write(sgrf_regmap, RK3288_SGRF_CPU_CON0, SGRF_DAPDEVICEEN_WRITE);
/* booting address of resuming system is from this register value */
regmap_write(sgrf_regmap, RK3288_SGRF_FAST_BOOT_ADDR,
rk3288_bootram_phy);
......
arch/arm/mach-rockchip/pm.h
浏览文件 @ 909eacd7
......@@ -55,6 +55,10 @@ static inline void rockchip_suspend_init(void)
#define SGRF_FAST_BOOT_EN BIT(8)
#define SGRF_FAST_BOOT_EN_WRITE BIT(24)
#define RK3288_SGRF_CPU_CON0 (0x40)
#define SGRF_DAPDEVICEEN BIT(0)
#define SGRF_DAPDEVICEEN_WRITE BIT(16)
#define RK3288_CRU_MODE_CON 0x50
#define RK3288_CRU_SEL0_CON 0x60
#define RK3288_CRU_SEL1_CON 0x64
......
arch/arm/mach-rockchip/rockchip.c
浏览文件 @ 909eacd7
......@@ -30,11 +30,30 @@
#include "pm.h"
#define RK3288_GRF_SOC_CON0 0x244
#define RK3288_TIMER6_7_PHYS 0xff810000
static void __init rockchip_timer_init(void)
{
if (of_machine_is_compatible("rockchip,rk3288")) {
struct regmap *grf;
void __iomem *reg_base;
/*
* Most/all uboot versions for rk3288 don't enable timer7
* which is needed for the architected timer to work.
* So make sure it is running during early boot.
*/
reg_base = ioremap(RK3288_TIMER6_7_PHYS, SZ_16K);
if (reg_base) {
writel(0, reg_base + 0x30);
writel(0xffffffff, reg_base + 0x20);
writel(0xffffffff, reg_base + 0x24);
writel(1, reg_base + 0x30);
dsb();
iounmap(reg_base);
} else {
pr_err("rockchip: could not map timer7 registers\n");
}
/*
* Disable auto jtag/sdmmc switching that causes issues
......
arch/arm/mm/dma-mapping.c
浏览文件 @ 909eacd7
......@@ -1878,7 +1878,7 @@ struct dma_map_ops iommu_coherent_ops = {
* arm_iommu_attach_device function.
*/
struct dma_iommu_mapping *
arm_iommu_create_mapping(struct bus_type *bus, dma_addr_t base, size_t size)
arm_iommu_create_mapping(struct bus_type *bus, dma_addr_t base, u64 size)
{
unsigned int bits = size >> PAGE_SHIFT;
unsigned int bitmap_size = BITS_TO_LONGS(bits) * sizeof(long);
......@@ -1886,6 +1886,10 @@ arm_iommu_create_mapping(struct bus_type *bus, dma_addr_t base, size_t size)
int extensions = 1;
int err = -ENOMEM;
/* currently only 32-bit DMA address space is supported */
if (size > DMA_BIT_MASK(32) + 1)
return ERR_PTR(-ERANGE);
if (!bitmap_size)
return ERR_PTR(-EINVAL);
......@@ -2057,13 +2061,6 @@ static bool arm_setup_iommu_dma_ops(struct device *dev, u64 dma_base, u64 size,
if (!iommu)
return false;
/*
* currently arm_iommu_create_mapping() takes a max of size_t
* for size param. So check this limit for now.
*/
if (size > SIZE_MAX)
return false;
mapping = arm_iommu_create_mapping(dev->bus, dma_base, size);
if (IS_ERR(mapping)) {
pr_warn("Failed to create %llu-byte IOMMU mapping for device %s\n",
......
arch/arm/mm/proc-arm1020.S
浏览文件 @ 909eacd7
......@@ -22,8 +22,6 @@
*
* These are the low level assembler for performing cache and TLB
* functions on the arm1020.
*
* CONFIG_CPU_ARM1020_CPU_IDLE -> nohlt
*/
#include <linux/linkage.h>
#include <linux/init.h>
......
arch/arm/mm/proc-arm1020e.S
浏览文件 @ 909eacd7
......@@ -22,8 +22,6 @@
*
* These are the low level assembler for performing cache and TLB
* functions on the arm1020e.
*
* CONFIG_CPU_ARM1020_CPU_IDLE -> nohlt
*/
#include <linux/linkage.h>
#include <linux/init.h>
......
arch/arm/mm/proc-arm925.S
浏览文件 @ 909eacd7
......@@ -441,9 +441,6 @@ ENTRY(cpu_arm925_set_pte_ext)
.type __arm925_setup, #function
__arm925_setup:
mov r0, #0
#if defined(CONFIG_CPU_ICACHE_STREAMING_DISABLE)
orr r0,r0,#1 << 7
#endif
/* Transparent on, D-cache clean & flush mode. See NOTE2 above */
orr r0,r0,#1 << 1 @ transparent mode on
......
arch/arm/mm/proc-feroceon.S
浏览文件 @ 909eacd7
......@@ -602,7 +602,6 @@ __\name\()_proc_info:
PMD_SECT_AP_WRITE | \
PMD_SECT_AP_READ
initfn __feroceon_setup, __\name\()_proc_info
.long __feroceon_setup
.long cpu_arch_name
.long cpu_elf_name
.long HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP
......
arch/arm/net/bpf_jit_32.c
浏览文件 @ 909eacd7
......@@ -54,6 +54,7 @@
#define SEEN_DATA (1 << (BPF_MEMWORDS + 3))
#define FLAG_NEED_X_RESET (1 << 0)
#define FLAG_IMM_OVERFLOW (1 << 1)
struct jit_ctx {
const struct bpf_prog *skf;
......@@ -293,6 +294,15 @@ static u16 imm_offset(u32 k, struct jit_ctx *ctx)
/* PC in ARM mode == address of the instruction + 8 */
imm = offset - (8 + ctx->idx * 4);
if (imm & ~0xfff) {
/*
* literal pool is too far, signal it into flags. we
* can only detect it on the second pass unfortunately.
*/
ctx->flags |= FLAG_IMM_OVERFLOW;
return 0;
}
return imm;
}
......@@ -449,10 +459,21 @@ static inline void emit_udiv(u8 rd, u8 rm, u8 rn, struct jit_ctx *ctx)
return;
}
#endif
if (rm != ARM_R0)
emit(ARM_MOV_R(ARM_R0, rm), ctx);
/*
* For BPF_ALU | BPF_DIV | BPF_K instructions, rm is ARM_R4
* (r_A) and rn is ARM_R0 (r_scratch) so load rn first into
* ARM_R1 to avoid accidentally overwriting ARM_R0 with rm
* before using it as a source for ARM_R1.
*
* For BPF_ALU | BPF_DIV | BPF_X rm is ARM_R4 (r_A) and rn is
* ARM_R5 (r_X) so there is no particular register overlap
* issues.
*/
if (rn != ARM_R1)
emit(ARM_MOV_R(ARM_R1, rn), ctx);
if (rm != ARM_R0)
emit(ARM_MOV_R(ARM_R0, rm), ctx);
ctx->seen |= SEEN_CALL;
emit_mov_i(ARM_R3, (u32)jit_udiv, ctx);
......@@ -855,6 +876,14 @@ static int build_body(struct jit_ctx *ctx)
default:
return -1;
}
if (ctx->flags & FLAG_IMM_OVERFLOW)
/*
* this instruction generated an overflow when
* trying to access the literal pool, so
* delegate this filter to the kernel interpreter.
*/
return -1;
}
/* compute offsets only during the first pass */
......@@ -917,7 +946,14 @@ void bpf_jit_compile(struct bpf_prog *fp)
ctx.idx = 0;
build_prologue(&ctx);
build_body(&ctx);
if (build_body(&ctx) < 0) {
#if __LINUX_ARM_ARCH__ < 7
if (ctx.imm_count)
kfree(ctx.imms);
#endif
bpf_jit_binary_free(header);
goto out;
}
build_epilogue(&ctx);
flush_icache_range((u32)ctx.target, (u32)(ctx.target + ctx.idx));
......
arch/arm/xen/mm.c
浏览文件 @ 909eacd7
......@@ -4,6 +4,7 @@
#include <linux/gfp.h>
#include <linux/highmem.h>
#include <linux/export.h>
#include <linux/memblock.h>
#include <linux/of_address.h>
#include <linux/slab.h>
#include <linux/types.h>
......@@ -21,6 +22,20 @@
#include <asm/xen/hypercall.h>
#include <asm/xen/interface.h>
unsigned long xen_get_swiotlb_free_pages(unsigned int order)
{
struct memblock_region *reg;
gfp_t flags = __GFP_NOWARN;
for_each_memblock(memory, reg) {
if (reg->base < (phys_addr_t)0xffffffff) {
flags |= __GFP_DMA;
break;
}
}
return __get_free_pages(flags, order);
}
enum dma_cache_op {
DMA_UNMAP,
DMA_MAP,
......
arch/arm64/boot/dts/arm/juno-motherboard.dtsi
浏览文件 @ 909eacd7
......@@ -21,6 +21,20 @@
clock-output-names = "juno_mb:clk25mhz";
};
v2m_refclk1mhz: refclk1mhz {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <1000000>;
clock-output-names = "juno_mb:refclk1mhz";
};
v2m_refclk32khz: refclk32khz {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
clock-output-names = "juno_mb:refclk32khz";
};
motherboard {
compatible = "arm,vexpress,v2p-p1", "simple-bus";
#address-cells = <2>; /* SMB chipselect number and offset */
......@@ -66,6 +80,15 @@
#size-cells = <1>;
ranges = <0 3 0 0x200000>;
v2m_sysctl: sysctl@020000 {
compatible = "arm,sp810", "arm,primecell";
reg = <0x020000 0x1000>;
clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&mb_clk24mhz>;
clock-names = "refclk", "timclk", "apb_pclk";
#clock-cells = <1>;
clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3";
};
mmci@050000 {
compatible = "arm,pl180", "arm,primecell";
reg = <0x050000 0x1000>;
......@@ -106,16 +129,16 @@
compatible = "arm,sp804", "arm,primecell";
reg = <0x110000 0x10000>;
interrupts = <9>;
clocks = <&mb_clk24mhz>, <&soc_smc50mhz>;
clock-names = "timclken1", "apb_pclk";
clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&mb_clk24mhz>;
clock-names = "timclken1", "timclken2", "apb_pclk";
};
v2m_timer23: timer@120000 {
compatible = "arm,sp804", "arm,primecell";
reg = <0x120000 0x10000>;
interrupts = <9>;
clocks = <&mb_clk24mhz>, <&soc_smc50mhz>;
clock-names = "timclken1", "apb_pclk";
clocks = <&v2m_sysctl 2>, <&v2m_sysctl 3>, <&mb_clk24mhz>;
clock-names = "timclken1", "timclken2", "apb_pclk";
};
rtc@170000 {
......
arch/arm64/crypto/crc32-arm64.c
浏览文件 @ 909eacd7
......@@ -147,13 +147,21 @@ static int chksum_final(struct shash_desc *desc, u8 *out)
{
struct chksum_desc_ctx *ctx = shash_desc_ctx(desc);
put_unaligned_le32(ctx->crc, out);
return 0;
}
static int chksumc_final(struct shash_desc *desc, u8 *out)
{
struct chksum_desc_ctx *ctx = shash_desc_ctx(desc);
put_unaligned_le32(~ctx->crc, out);
return 0;
}
static int __chksum_finup(u32 crc, const u8 *data, unsigned int len, u8 *out)
{
put_unaligned_le32(~crc32_arm64_le_hw(crc, data, len), out);
put_unaligned_le32(crc32_arm64_le_hw(crc, data, len), out);
return 0;
}
......@@ -199,6 +207,14 @@ static int crc32_cra_init(struct crypto_tfm *tfm)
{
struct chksum_ctx *mctx = crypto_tfm_ctx(tfm);
mctx->key = 0;
return 0;
}
static int crc32c_cra_init(struct crypto_tfm *tfm)
{
struct chksum_ctx *mctx = crypto_tfm_ctx(tfm);
mctx->key = ~0;
return 0;
}
......@@ -229,7 +245,7 @@ static struct shash_alg crc32c_alg = {
.setkey = chksum_setkey,
.init = chksum_init,
.update = chksumc_update,
.final = chksum_final,
.final = chksumc_final,
.finup = chksumc_finup,
.digest = chksumc_digest,
.descsize = sizeof(struct chksum_desc_ctx),
......@@ -241,7 +257,7 @@ static struct shash_alg crc32c_alg = {
.cra_alignmask = 0,
.cra_ctxsize = sizeof(struct chksum_ctx),
.cra_module = THIS_MODULE,
.cra_init = crc32_cra_init,
.cra_init = crc32c_cra_init,
}
};
......
arch/arm64/crypto/sha1-ce-glue.c
浏览文件 @ 909eacd7
......@@ -74,6 +74,9 @@ static int sha1_ce_finup(struct shash_desc *desc, const u8 *data,
static int sha1_ce_final(struct shash_desc *desc, u8 *out)
{
struct sha1_ce_state *sctx = shash_desc_ctx(desc);
sctx->finalize = 0;
kernel_neon_begin_partial(16);
sha1_base_do_finalize(desc, (sha1_block_fn *)sha1_ce_transform);
kernel_neon_end();
......
arch/arm64/crypto/sha2-ce-glue.c
浏览文件 @ 909eacd7
......@@ -75,6 +75,9 @@ static int sha256_ce_finup(struct shash_desc *desc, const u8 *data,
static int sha256_ce_final(struct shash_desc *desc, u8 *out)
{
struct sha256_ce_state *sctx = shash_desc_ctx(desc);
sctx->finalize = 0;
kernel_neon_begin_partial(28);
sha256_base_do_finalize(desc, (sha256_block_fn *)sha2_ce_transform);
kernel_neon_end();
......
arch/arm64/kernel/alternative.c
浏览文件 @ 909eacd7
......@@ -24,7 +24,6 @@
#include <asm/cacheflush.h>
#include <asm/alternative.h>
#include <asm/cpufeature.h>
#include <asm/insn.h>
#include <linux/stop_machine.h>
extern struct alt_instr __alt_instructions[], __alt_instructions_end[];
......@@ -34,48 +33,6 @@ struct alt_region {
struct alt_instr *end;
};
/*
* Decode the imm field of a b/bl instruction, and return the byte
* offset as a signed value (so it can be used when computing a new
* branch target).
*/
static s32 get_branch_offset(u32 insn)
{
s32 imm = aarch64_insn_decode_immediate(AARCH64_INSN_IMM_26, insn);
/* sign-extend the immediate before turning it into a byte offset */
return (imm << 6) >> 4;
}
static u32 get_alt_insn(u8 *insnptr, u8 *altinsnptr)
{
u32 insn;
aarch64_insn_read(altinsnptr, &insn);
/* Stop the world on instructions we don't support... */
BUG_ON(aarch64_insn_is_cbz(insn));
BUG_ON(aarch64_insn_is_cbnz(insn));
BUG_ON(aarch64_insn_is_bcond(insn));
/* ... and there is probably more. */
if (aarch64_insn_is_b(insn) || aarch64_insn_is_bl(insn)) {
enum aarch64_insn_branch_type type;
unsigned long target;
if (aarch64_insn_is_b(insn))
type = AARCH64_INSN_BRANCH_NOLINK;
else
type = AARCH64_INSN_BRANCH_LINK;
target = (unsigned long)altinsnptr + get_branch_offset(insn);
insn = aarch64_insn_gen_branch_imm((unsigned long)insnptr,
target, type);
}
return insn;
}
static int __apply_alternatives(void *alt_region)
{
struct alt_instr *alt;
......@@ -83,9 +40,6 @@ static int __apply_alternatives(void *alt_region)
u8 *origptr, *replptr;
for (alt = region->begin; alt < region->end; alt++) {
u32 insn;
int i;
if (!cpus_have_cap(alt->cpufeature))
continue;
......@@ -95,12 +49,7 @@ static int __apply_alternatives(void *alt_region)
origptr = (u8 *)&alt->orig_offset + alt->orig_offset;
replptr = (u8 *)&alt->alt_offset + alt->alt_offset;
for (i = 0; i < alt->alt_len; i += sizeof(insn)) {
insn = get_alt_insn(origptr + i, replptr + i);
aarch64_insn_write(origptr + i, insn);
}
memcpy(origptr, replptr, alt->alt_len);
flush_icache_range((uintptr_t)origptr,
(uintptr_t)(origptr + alt->alt_len));
}
......
arch/arm64/kernel/perf_event.c
浏览文件 @ 909eacd7
......@@ -1315,15 +1315,15 @@ static int armpmu_device_probe(struct platform_device *pdev)
if (!cpu_pmu)
return -ENODEV;
irqs = kcalloc(pdev->num_resources, sizeof(*irqs), GFP_KERNEL);
if (!irqs)
return -ENOMEM;
/* Don't bother with PPIs; they're already affine */
irq = platform_get_irq(pdev, 0);
if (irq >= 0 && irq_is_percpu(irq))
return 0;
irqs = kcalloc(pdev->num_resources, sizeof(*irqs), GFP_KERNEL);
if (!irqs)
return -ENOMEM;
for (i = 0; i < pdev->num_resources; ++i) {
struct device_node *dn;
int cpu;
......
arch/arm64/mm/dump.c
浏览文件 @ 909eacd7
......@@ -328,10 +328,12 @@ static int ptdump_init(void)
for (j = 0; j < pg_level[i].num; j++)
pg_level[i].mask |= pg_level[i].bits[j].mask;
#ifdef CONFIG_SPARSEMEM_VMEMMAP
address_markers[VMEMMAP_START_NR].start_address =
(unsigned long)virt_to_page(PAGE_OFFSET);
address_markers[VMEMMAP_END_NR].start_address =
(unsigned long)virt_to_page(high_memory);
#endif
pe = debugfs_create_file("kernel_page_tables", 0400, NULL, NULL,
&ptdump_fops);
......
arch/arm64/net/bpf_jit_comp.c
浏览文件 @ 909eacd7
......@@ -487,7 +487,7 @@ static int build_insn(const struct bpf_insn *insn, struct jit_ctx *ctx)
return -EINVAL;
}
imm64 = (u64)insn1.imm << 32 | imm;
imm64 = (u64)insn1.imm << 32 | (u32)imm;
emit_a64_mov_i64(dst, imm64, ctx);
return 1;
......
arch/m32r/kernel/smp.c
浏览文件 @ 909eacd7
......@@ -45,7 +45,7 @@ static volatile unsigned long flushcache_cpumask = 0;
/*
* For flush_tlb_others()
*/
static volatile cpumask_t flush_cpumask;
static cpumask_t flush_cpumask;
static struct mm_struct *flush_mm;
static struct vm_area_struct *flush_vma;
static volatile unsigned long flush_va;
......@@ -415,7 +415,7 @@ static void flush_tlb_others(cpumask_t cpumask, struct mm_struct *mm,
*/
send_IPI_mask(&cpumask, INVALIDATE_TLB_IPI, 0);
while (!cpumask_empty((cpumask_t*)&flush_cpumask)) {
while (!cpumask_empty(&flush_cpumask)) {
/* nothing. lockup detection does not belong here */
mb();
}
......@@ -468,7 +468,7 @@ void smp_invalidate_interrupt(void)
__flush_tlb_page(va);
}
}
cpumask_clear_cpu(cpu_id, (cpumask_t*)&flush_cpumask);
cpumask_clear_cpu(cpu_id, &flush_cpumask);
}
/*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*/
......
arch/mips/Makefile
浏览文件 @ 909eacd7
......@@ -277,7 +277,7 @@ LDFLAGS += -m $(ld-emul)
ifdef CONFIG_MIPS
CHECKFLAGS += $(shell $(CC) $(KBUILD_CFLAGS) -dM -E -x c /dev/null | \
egrep -vw '__GNUC_(|MINOR_|PATCHLEVEL_)_' | \
sed -e "s/^\#define /-D'/" -e "s/ /'='/" -e "s/$$/'/")
sed -e "s/^\#define /-D'/" -e "s/ /'='/" -e "s/$$/'/" -e 's/\$$/&&/g')
ifdef CONFIG_64BIT
CHECKFLAGS += -m64
endif
......
arch/mips/include/asm/elf.h
浏览文件 @ 909eacd7
......@@ -304,7 +304,7 @@ do { \
\
current->thread.abi = &mips_abi; \
\
current->thread.fpu.fcr31 = current_cpu_data.fpu_csr31; \
current->thread.fpu.fcr31 = boot_cpu_data.fpu_csr31; \
} while (0)
#endif /* CONFIG_32BIT */
......@@ -366,7 +366,7 @@ do { \
else \
current->thread.abi = &mips_abi; \
\
current->thread.fpu.fcr31 = current_cpu_data.fpu_csr31; \
current->thread.fpu.fcr31 = boot_cpu_data.fpu_csr31; \
\
p = personality(current->personality); \
if (p != PER_LINUX32 && p != PER_LINUX) \
......
arch/mips/include/asm/smp.h
浏览文件 @ 909eacd7
......@@ -45,7 +45,7 @@ extern int __cpu_logical_map[NR_CPUS];
#define SMP_DUMP 0x8
#define SMP_ASK_C0COUNT 0x10
extern volatile cpumask_t cpu_callin_map;
extern cpumask_t cpu_callin_map;
/* Mask of CPUs which are currently definitely operating coherently */
extern cpumask_t cpu_coherent_mask;
......
arch/mips/kernel/elf.c
浏览文件 @ 909eacd7
......@@ -76,14 +76,6 @@ int arch_elf_pt_proc(void *_ehdr, void *_phdr, struct file *elf,
/* Lets see if this is an O32 ELF */
if (ehdr32->e_ident[EI_CLASS] == ELFCLASS32) {
/* FR = 1 for N32 */
if (ehdr32->e_flags & EF_MIPS_ABI2)
state->overall_fp_mode = FP_FR1;
else
/* Set a good default FPU mode for O32 */
state->overall_fp_mode = cpu_has_mips_r6 ?
FP_FRE : FP_FR0;
if (ehdr32->e_flags & EF_MIPS_FP64) {
/*
* Set MIPS_ABI_FP_OLD_64 for EF_MIPS_FP64. We will override it
......@@ -104,9 +96,6 @@ int arch_elf_pt_proc(void *_ehdr, void *_phdr, struct file *elf,
(char *)&abiflags,
sizeof(abiflags));
} else {
/* FR=1 is really the only option for 64-bit */
state->overall_fp_mode = FP_FR1;
if (phdr64->p_type != PT_MIPS_ABIFLAGS)
return 0;
if (phdr64->p_filesz < sizeof(abiflags))
......@@ -137,6 +126,7 @@ int arch_check_elf(void *_ehdr, bool has_interpreter,
struct elf32_hdr *ehdr = _ehdr;
struct mode_req prog_req, interp_req;
int fp_abi, interp_fp_abi, abi0, abi1, max_abi;
bool is_mips64;
if (!config_enabled(CONFIG_MIPS_O32_FP64_SUPPORT))
return 0;
......@@ -152,10 +142,22 @@ int arch_check_elf(void *_ehdr, bool has_interpreter,
abi0 = abi1 = fp_abi;
}
/* ABI limits. O32 = FP_64A, N32/N64 = FP_SOFT */
max_abi = ((ehdr->e_ident[EI_CLASS] == ELFCLASS32) &&
(!(ehdr->e_flags & EF_MIPS_ABI2))) ?
MIPS_ABI_FP_64A : MIPS_ABI_FP_SOFT;
is_mips64 = (ehdr->e_ident[EI_CLASS] == ELFCLASS64) ||
(ehdr->e_flags & EF_MIPS_ABI2);
if (is_mips64) {
/* MIPS64 code always uses FR=1, thus the default is easy */
state->overall_fp_mode = FP_FR1;
/* Disallow access to the various FPXX & FP64 ABIs */
max_abi = MIPS_ABI_FP_SOFT;
} else {
/* Default to a mode capable of running code expecting FR=0 */
state->overall_fp_mode = cpu_has_mips_r6 ? FP_FRE : FP_FR0;
/* Allow all ABIs we know about */
max_abi = MIPS_ABI_FP_64A;
}
if ((abi0 > max_abi && abi0 != MIPS_ABI_FP_UNKNOWN) ||
(abi1 > max_abi && abi1 != MIPS_ABI_FP_UNKNOWN))
......
arch/mips/kernel/ptrace.c
浏览文件 @ 909eacd7
......@@ -176,7 +176,7 @@ int ptrace_setfpregs(struct task_struct *child, __u32 __user *data)
__get_user(value, data + 64);
fcr31 = child->thread.fpu.fcr31;
mask = current_cpu_data.fpu_msk31;
mask = boot_cpu_data.fpu_msk31;
child->thread.fpu.fcr31 = (value & ~mask) | (fcr31 & mask);
/* FIR may not be written. */
......
arch/mips/kernel/smp-cps.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/mips/kernel/smp.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/mips/kernel/traps.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/mips/kvm/emulate.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/mips/math-emu/cp1emu.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/mips/mm/tlb-r4k.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/mips/sgi-ip32/ip32-platform.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/parisc/include/asm/elf.h
浏览文件 @ 909eacd7
此差异已折叠。
arch/parisc/kernel/process.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/parisc/kernel/sys_parisc.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/x86/boot/compressed/eboot.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/x86/include/asm/hypervisor.h
浏览文件 @ 909eacd7
此差异已折叠。
arch/x86/include/asm/spinlock.h
浏览文件 @ 909eacd7
此差异已折叠。
arch/x86/include/asm/xen/page.h
浏览文件 @ 909eacd7
此差异已折叠。
arch/x86/kernel/cpu/hypervisor.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/x86/kernel/process.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/x86/mm/ioremap.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/x86/net/bpf_jit_comp.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/x86/pci/acpi.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/x86/vdso/Makefile
浏览文件 @ 909eacd7
此差异已折叠。
arch/x86/xen/enlighten.c
浏览文件 @ 909eacd7
此差异已折叠。
arch/x86/xen/suspend.c
浏览文件 @ 909eacd7
此差异已折叠。
block/blk-core.c
浏览文件 @ 909eacd7
此差异已折叠。
block/blk-mq.c
浏览文件 @ 909eacd7
此差异已折叠。
block/blk-sysfs.c
浏览文件 @ 909eacd7
此差异已折叠。
block/bounce.c
浏览文件 @ 909eacd7
此差异已折叠。
block/elevator.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/acpi/acpi_pnp.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/acpi/acpica/utglobal.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/acpi/osl.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/acpi/resource.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/acpi/sbshc.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/ata/Kconfig
浏览文件 @ 909eacd7
此差异已折叠。
drivers/ata/Makefile
浏览文件 @ 909eacd7
此差异已折叠。
drivers/ata/ahci.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/ata/ahci_st.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/ata/libahci.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/ata/libata-core.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/ata/libata-eh.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/ata/pata_scc.c 已删除 100644 → 0
浏览文件 @ aa519be3
此差异已折叠。
drivers/block/loop.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/block/nvme-scsi.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/block/xen-blkback/blkback.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/block/zram/zram_drv.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/bluetooth/bt3c_cs.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/bluetooth/btbcm.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/bluetooth/btbcm.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/bluetooth/btusb.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/bluetooth/hci_ath.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/bus/arm-cci.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/bus/omap_l3_noc.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/bus/omap_l3_noc.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/char/ipmi/ipmi_msghandler.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/char/ipmi/ipmi_si_intf.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/char/ipmi/ipmi_ssif.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/extcon/extcon-usb-gpio.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/firmware/dmi_scan.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/firmware/efi/runtime-map.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpio/gpio-omap.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpio/gpiolib-acpi.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpio/gpiolib-sysfs.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/drm_irq.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/i915/i915_drv.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/i915/intel_dp.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/i915/intel_lvds.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/radeon/cik.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/radeon/evergreen.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/radeon/ni.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/radeon/r600.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/radeon/radeon.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/radeon/radeon_mn.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/radeon/radeon_ttm.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/radeon/radeon_uvd.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/radeon/radeon_vce.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/radeon/rv770.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/radeon/rv770d.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/radeon/si.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/radeon/uvd_v1_0.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/radeon/uvd_v2_2.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/gpu/drm/tegra/drm.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/ide/Kconfig
浏览文件 @ 909eacd7
此差异已折叠。
drivers/ide/Makefile
浏览文件 @ 909eacd7
此差异已折叠。
drivers/ide/scc_pata.c 已删除 100644 → 0
浏览文件 @ aa519be3
此差异已折叠。
drivers/iio/accel/mma9551_core.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/iio/accel/mma9553.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/iio/accel/st_accel_core.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/iio/adc/axp288_adc.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/iio/adc/cc10001_adc.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/iio/adc/mcp320x.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/iio/adc/qcom-spmi-vadc.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/iio/adc/xilinx-xadc-core.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/iio/adc/xilinx-xadc.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/iio/gyro/st_gyro_core.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/iio/kfifo_buf.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/iio/light/hid-sensor-prox.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/iio/pressure/bmp280.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/core/addr.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/core/cm.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/core/cm_msgs.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/core/cma.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/core/iwpm_msg.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/core/iwpm_util.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/core/iwpm_util.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/core/umem_odp.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/hw/cxgb4/cm.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/hw/cxgb4/cq.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/hw/cxgb4/mem.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/hw/cxgb4/qp.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/hw/cxgb4/t4.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/hw/mlx4/main.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/hw/mlx5/qp.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/hw/nes/nes.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/hw/nes/nes_cm.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/infiniband/hw/qib/qib.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/iommu/amd_iommu_v2.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/iommu/arm-smmu.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/iommu/rockchip-iommu.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/irqchip/irq-gic.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/irqchip/irq-tegra.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/md/dm-crypt.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/md/md.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/md/raid0.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/md/raid5.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/mmc/card/block.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/mmc/card/queue.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/mmc/card/queue.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/mmc/core/core.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/mmc/host/dw_mmc.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/mmc/host/sh_mmcif.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/mtd/devices/m25p80.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/mtd/tests/readtest.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/mtd/ubi/block.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/net/can/xilinx_can.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/net/dsa/mv88e6xxx.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/net/ethernet/amd/Kconfig
浏览文件 @ 909eacd7
此差异已折叠。
drivers/net/ethernet/cadence/macb.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/net/ethernet/smsc/smc91x.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/net/hyperv/netvsc.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/net/ieee802154/at86rf230.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/net/macvlan.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/net/phy/Kconfig
浏览文件 @ 909eacd7
此差异已折叠。
drivers/net/phy/mdio-gpio.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/net/phy/micrel.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/net/ppp/pppoe.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/net/usb/r8152.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/net/usb/usbnet.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/net/wireless/rtlwifi/usb.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/parisc/superio.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/pinctrl/core.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/pinctrl/core.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/pinctrl/devicetree.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/power/axp288_fuel_gauge.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/power/bq27x00_battery.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/power/collie_battery.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/power/reset/Kconfig
浏览文件 @ 909eacd7
此差异已折叠。
drivers/power/reset/at91-reset.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/rtc/Kconfig
浏览文件 @ 909eacd7
此差异已折叠。
drivers/rtc/Makefile
浏览文件 @ 909eacd7
此差异已折叠。
drivers/rtc/rtc-abx80x.c 0 → 100644
浏览文件 @ 909eacd7
此差异已折叠。
drivers/rtc/rtc-armada38x.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/spi/Kconfig
浏览文件 @ 909eacd7
此差异已折叠。
drivers/spi/spi-bcm2835.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/spi/spi-bitbang.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/spi/spi-fsl-cpm.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/spi/spi-fsl-espi.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/spi/spi-omap2-mcspi.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/spi/spi.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/staging/gdm724x/gdm_mux.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/staging/sm750fb/sm750.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/staging/vt6655/card.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/staging/vt6655/card.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/staging/vt6656/rxtx.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/thermal/intel_powerclamp.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/thermal/rockchip_thermal.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/thermal/thermal_core.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/tty/hvc/hvc_xen.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/tty/n_gsm.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/tty/n_hdlc.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/tty/n_tty.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/tty/pty.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/tty/serial/amba-pl011.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/tty/serial/earlycon.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/tty/serial/omap-serial.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/tty/tty_buffer.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/chipidea/debug.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/core/quirks.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/dwc3/dwc3-omap.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/configfs.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/function/f_hid.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/legacy/acm_ms.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/legacy/audio.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/legacy/cdc2.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/legacy/dbgp.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/legacy/ether.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/legacy/g_ffs.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/legacy/gmidi.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/legacy/hid.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/legacy/multi.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/legacy/ncm.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/legacy/nokia.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/legacy/printer.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/legacy/serial.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/legacy/webcam.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/legacy/zero.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/udc/at91_udc.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/udc/m66592-udc.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/gadget/udc/udc-xilinx.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/host/xhci-ring.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/host/xhci.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/phy/phy-isp1301-omap.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/serial/cp210x.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/serial/pl2303.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/serial/pl2303.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/serial/visor.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/usb/storage/unusual_devs.h
浏览文件 @ 909eacd7
此差异已折叠。
drivers/vfio/pci/vfio_pci.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/vfio/vfio.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/xen/events/events_2l.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/xen/events/events_base.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/xen/gntdev.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/xen/grant-table.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/xen/manage.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/xen/swiotlb-xen.c
浏览文件 @ 909eacd7
此差异已折叠。
drivers/xen/xenbus/xenbus_probe.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/btrfs/extent-tree.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/btrfs/extent_io.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/btrfs/free-space-cache.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/btrfs/ordered-data.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/configfs/mount.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/efivarfs/super.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/exec.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/ext4/ext4.h
浏览文件 @ 909eacd7
此差异已折叠。
fs/ext4/ext4_jbd2.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/ext4/extents.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/ext4/inode.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/ext4/super.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/f2fs/data.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/f2fs/f2fs.h
浏览文件 @ 909eacd7
此差异已折叠。
fs/f2fs/namei.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/f2fs/super.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/hostfs/hostfs_kern.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/jbd2/recovery.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/jbd2/revoke.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/jbd2/transaction.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/kernfs/dir.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/namei.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/namespace.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/nfsd/blocklayout.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/nfsd/nfs4callback.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/nfsd/nfs4state.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/nfsd/state.h
浏览文件 @ 909eacd7
此差异已折叠。
fs/nfsd/xdr4.h
浏览文件 @ 909eacd7
此差异已折叠。
fs/nilfs2/btree.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/ocfs2/dlm/dlmmaster.c
浏览文件 @ 909eacd7
此差异已折叠。
fs/splice.c
浏览文件 @ 909eacd7
此差异已折叠。
include/drm/drm_pciids.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/blk_types.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/compiler-gcc.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/compiler-intel.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/compiler.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/ftrace_event.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/gfp.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/irqchip/arm-gic.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/libata.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/memcontrol.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/netdevice.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/nilfs2_fs.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/pci_ids.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/sched/rt.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/tcp.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/tty.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/uidgid.h
浏览文件 @ 909eacd7
此差异已折叠。
include/linux/util_macros.h
浏览文件 @ 909eacd7
此差异已折叠。
include/net/cfg802154.h
浏览文件 @ 909eacd7
此差异已折叠。
include/net/codel.h
浏览文件 @ 909eacd7
此差异已折叠。
include/net/mac80211.h
浏览文件 @ 909eacd7
此差异已折叠。
include/net/mac802154.h
浏览文件 @ 909eacd7
此差异已折叠。
include/net/tcp.h
浏览文件 @ 909eacd7
此差异已折叠。
include/rdma/ib_addr.h
浏览文件 @ 909eacd7
此差异已折叠。
include/rdma/ib_cm.h
浏览文件 @ 909eacd7
此差异已折叠。
include/rdma/iw_portmap.h
浏览文件 @ 909eacd7
此差异已折叠。
include/uapi/linux/inet_diag.h
浏览文件 @ 909eacd7
此差异已折叠。
include/uapi/linux/mpls.h
浏览文件 @ 909eacd7
此差异已折叠。
include/uapi/linux/tcp.h
浏览文件 @ 909eacd7
此差异已折叠。
include/uapi/rdma/rdma_netlink.h
浏览文件 @ 909eacd7
此差异已折叠。
include/xen/grant_table.h
浏览文件 @ 909eacd7
此差异已折叠。
include/xen/xen-ops.h
浏览文件 @ 909eacd7
此差异已折叠。
init/do_mounts.c
浏览文件 @ 909eacd7
此差异已折叠。
kernel/events/core.c
浏览文件 @ 909eacd7
此差异已折叠。
kernel/irq/dummychip.c
浏览文件 @ 909eacd7
此差异已折叠。
kernel/locking/rtmutex.c
浏览文件 @ 909eacd7
此差异已折叠。
kernel/rcu/tree.c
浏览文件 @ 909eacd7
此差异已折叠。
kernel/sched/core.c
浏览文件 @ 909eacd7
此差异已折叠。
kernel/time/clockevents.c
浏览文件 @ 909eacd7
此差异已折叠。
kernel/trace/trace_output.c
浏览文件 @ 909eacd7
此差异已折叠。
kernel/watchdog.c
浏览文件 @ 909eacd7
此差异已折叠。
lib/Kconfig.debug
浏览文件 @ 909eacd7
此差异已折叠。
lib/Kconfig.kasan
浏览文件 @ 909eacd7
此差异已折叠。
lib/find_last_bit.c 已删除 100644 → 0
浏览文件 @ aa519be3
此差异已折叠。
lib/string.c
浏览文件 @ 909eacd7
此差异已折叠。
mm/hwpoison-inject.c
浏览文件 @ 909eacd7
此差异已折叠。
mm/kmemleak.c
浏览文件 @ 909eacd7
此差异已折叠。
mm/memory-failure.c
浏览文件 @ 909eacd7
此差异已折叠。
mm/mempolicy.c
浏览文件 @ 909eacd7
此差异已折叠。
mm/page-writeback.c
浏览文件 @ 909eacd7
此差异已折叠。
mm/page_isolation.c
浏览文件 @ 909eacd7
此差异已折叠。
net/bluetooth/hci_core.c
浏览文件 @ 909eacd7
此差异已折叠。
net/core/dev.c
浏览文件 @ 909eacd7
此差异已折叠。
net/core/net_namespace.c
浏览文件 @ 909eacd7
此差异已折叠。
net/core/sock.c
浏览文件 @ 909eacd7
此差异已折叠。
net/ieee802154/Makefile
浏览文件 @ 909eacd7
此差异已折叠。
net/ieee802154/nl-phy.c
浏览文件 @ 909eacd7
此差异已折叠。
net/ieee802154/nl802154.c
浏览文件 @ 909eacd7
此差异已折叠。
net/ieee802154/rdev-ops.h
浏览文件 @ 909eacd7
此差异已折叠。
net/ieee802154/trace.c 0 → 100644
浏览文件 @ 909eacd7
此差异已折叠。
net/ieee802154/trace.h 0 → 100644
浏览文件 @ 909eacd7
此差异已折叠。
net/ipv4/inet_diag.c
浏览文件 @ 909eacd7
此差异已折叠。
net/ipv4/tcp.c
浏览文件 @ 909eacd7
此差异已折叠。
net/ipv4/tcp_dctcp.c
浏览文件 @ 909eacd7
此差异已折叠。
net/ipv4/tcp_fastopen.c
浏览文件 @ 909eacd7
此差异已折叠。
net/ipv4/tcp_illinois.c
浏览文件 @ 909eacd7
此差异已折叠。
net/ipv4/tcp_input.c
浏览文件 @ 909eacd7
此差异已折叠。
net/ipv4/tcp_vegas.c
浏览文件 @ 909eacd7
此差异已折叠。
net/ipv4/tcp_vegas.h
浏览文件 @ 909eacd7
此差异已折叠。
net/ipv4/tcp_westwood.c
浏览文件 @ 909eacd7
此差异已折叠。
net/ipv6/ip6_output.c
浏览文件 @ 909eacd7
此差异已折叠。
net/ipv6/route.c
浏览文件 @ 909eacd7
此差异已折叠。
net/mac80211/iface.c
浏览文件 @ 909eacd7
此差异已折叠。
net/mac80211/sta_info.c
浏览文件 @ 909eacd7
此差异已折叠。
net/mac802154/cfg.c
浏览文件 @ 909eacd7
此差异已折叠。
net/mac802154/ieee802154_i.h
浏览文件 @ 909eacd7
此差异已折叠。
net/mac802154/iface.c
浏览文件 @ 909eacd7
此差异已折叠。
net/mac802154/llsec.c
浏览文件 @ 909eacd7
此差异已折叠。
net/mac802154/main.c
浏览文件 @ 909eacd7
此差异已折叠。
net/mpls/af_mpls.c
浏览文件 @ 909eacd7
此差异已折叠。
net/mpls/internal.h
浏览文件 @ 909eacd7
此差异已折叠。
net/netlink/af_netlink.c
浏览文件 @ 909eacd7
此差异已折叠。
net/packet/af_packet.c
浏览文件 @ 909eacd7
此差异已折叠。
net/rds/connection.c
浏览文件 @ 909eacd7
此差异已折叠。
net/rds/ib_cm.c
浏览文件 @ 909eacd7
此差异已折叠。
net/rds/tcp_connect.c
浏览文件 @ 909eacd7
此差异已折叠。
net/rds/tcp_listen.c
浏览文件 @ 909eacd7
此差异已折叠。
net/sched/cls_api.c
浏览文件 @ 909eacd7
此差异已折叠。
net/sched/sch_codel.c
浏览文件 @ 909eacd7
此差异已折叠。
net/sched/sch_fq_codel.c
浏览文件 @ 909eacd7
此差异已折叠。
net/sched/sch_gred.c
浏览文件 @ 909eacd7
此差异已折叠。
net/sunrpc/auth_gss/gss_rpc_xdr.c
浏览文件 @ 909eacd7
此差异已折叠。
tools/lib/api/Makefile
浏览文件 @ 909eacd7
此差异已折叠。
tools/lib/lockdep/Makefile
浏览文件 @ 909eacd7
此差异已折叠。
tools/lib/traceevent/event-parse.c
浏览文件 @ 909eacd7
此差异已折叠。
tools/perf/Makefile
浏览文件 @ 909eacd7
此差异已折叠。
tools/perf/bench/futex-requeue.c
浏览文件 @ 909eacd7
此差异已折叠。
tools/perf/bench/numa.c
浏览文件 @ 909eacd7
此差异已折叠。
tools/perf/builtin-kmem.c
浏览文件 @ 909eacd7
此差异已折叠。
tools/perf/builtin-report.c
浏览文件 @ 909eacd7
此差异已折叠。
tools/perf/builtin-top.c
浏览文件 @ 909eacd7
此差异已折叠。
tools/perf/builtin-trace.c
浏览文件 @ 909eacd7
此差异已折叠。
tools/perf/util/probe-event.c
浏览文件 @ 909eacd7
此差异已折叠。
tools/perf/util/probe-finder.c
浏览文件 @ 909eacd7
此差异已折叠。
tools/testing/selftests/x86/check_cc.sh 0 → 100755
浏览文件 @ 909eacd7
此差异已折叠。
tools/testing/selftests/x86/run_x86_tests.sh 已删除 100644 → 0
浏览文件 @ aa519be3
此差异已折叠。
tools/testing/selftests/x86/trivial_64bit_program.c 0 → 100644
浏览文件 @ 909eacd7
此差异已折叠。
tools/thermal/tmon/Makefile
浏览文件 @ 909eacd7
此差异已折叠。
tools/vm/Makefile
浏览文件 @ 909eacd7
此差异已折叠。
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或