Blackfin arch: Add new board support for ADZS-BF526-EZ-BRD

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

arch/blackfin/Kconfig

@@ -249,7 +249,7 @@ config MEM_MT48LC8M32B2B5_7
 
 config MEM_MT48LC32M16A2TG_75
 	bool
-	depends on (BFIN527_EZKIT || BFIN532_IP0X || BLACKSTAMP)
+	depends on (BFIN527_EZKIT || BFIN532_IP0X || BLACKSTAMP || BFIN526_EZBRD)
 	default y
 
 source "arch/blackfin/mach-bf527/Kconfig"
@@ -286,13 +286,20 @@ config BOOT_LOAD
 	  memory region is used to capture NULL pointer references as well
 	  as some core kernel functions.
 
+config ROM_BASE
+	hex "Kernel ROM Base"
+	default "0x20040000"
+	range 0x20000000 0x20400000 if !(BF54x || BF561)
+	range 0x20000000 0x30000000 if (BF54x || BF561)
+	help
+
 comment "Clock/PLL Setup"
 
 config CLKIN_HZ
 	int "Frequency of the crystal on the board in Hz"
 	default "11059200" if BFIN533_STAMP
 	default "27000000" if BFIN533_EZKIT
-	default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS || BLACKSTAMP)
+	default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD)
 	default "30000000" if BFIN561_EZKIT
 	default "24576000" if PNAV10
 	default "10000000" if BFIN532_IP0X
@@ -332,7 +339,7 @@ config VCO_MULT
 	default "22" if BFIN533_BLUETECHNIX_CM
 	default "20" if (BFIN537_BLUETECHNIX_CM || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
 	default "20" if BFIN561_EZKIT
-	default "16" if (H8606_HVSISTEMAS || BLACKSTAMP)
+	default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD)
 	help
 	  This controls the frequency of the on-chip PLL. This can be between 1 and 64.
 	  PLL Frequency = (Crystal Frequency) * (this setting)

arch/blackfin/mach-bf527/boards/Kconfig

@@ -14,4 +14,9 @@ config BFIN527_BLUETECHNIX_CM
 	help
 	  CM-BF527 support for EVAL- and DEV-Board.
 
+config BFIN526_EZBRD
+	bool "BF526-EZBRD"
+	help
+	  BF526-EZBRD/EZKIT Lite board support.
+
 endchoice

arch/blackfin/mach-bf527/boards/Makefile

@@ -4,3 +4,4 @@
 
 obj-$(CONFIG_BFIN527_EZKIT)            += ezkit.o
 obj-$(CONFIG_BFIN527_BLUETECHNIX_CM)   += cm_bf527.o
+obj-$(CONFIG_BFIN526_EZBRD)            += ezbrd.o

arch/blackfin/mach-bf527/boards/ezbrd.c

+/*
+ * File:         arch/blackfin/mach-bf527/boards/ezbrd.c
+ * Based on:     arch/blackfin/mach-bf537/boards/stamp.c
+ * Author:       Aidan Williams <aidan@nicta.com.au>
+ *
+ * Created:
+ * Description:
+ *
+ * Modified:
+ *               Copyright 2005 National ICT Australia (NICTA)
+ *               Copyright 2004-2008 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+
+#include <linux/i2c.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/usb/musb.h>
+#include <asm/dma.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/reboot.h>
+#include <asm/nand.h>
+#include <asm/portmux.h>
+#include <asm/dpmc.h>
+#include <linux/spi/ad7877.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+const char bfin_board_name[] = "BF526-EZBRD";
+
+/*
+ *  Driver needs to know address, irq and flag pin.
+ */
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+static struct resource musb_resources[] = {
+	[0] = {
+		.start	= 0xffc03800,
+		.end	= 0xffc03cff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {	/* general IRQ */
+		.start	= IRQ_USB_INT0,
+		.end	= IRQ_USB_INT0,
+		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+	[2] = {	/* DMA IRQ */
+		.start	= IRQ_USB_DMA,
+		.end	= IRQ_USB_DMA,
+		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct musb_hdrc_config musb_config = {
+	.multipoint	= 0,
+	.dyn_fifo	= 0,
+	.soft_con	= 1,
+	.dma		= 1,
+	.num_eps	= 7,
+	.dma_channels	= 7,
+	.gpio_vrsel	= GPIO_PG13,
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#if defined(CONFIG_USB_MUSB_OTG)
+	.mode		= MUSB_OTG,
+#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
+	.mode		= MUSB_HOST,
+#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
+	.mode		= MUSB_PERIPHERAL,
+#endif
+	.config		= &musb_config,
+};
+
+static u64 musb_dmamask = ~(u32)0;
+
+static struct platform_device musb_device = {
+	.name		= "musb_hdrc",
+	.id		= 0,
+	.dev = {
+		.dma_mask		= &musb_dmamask,
+		.coherent_dma_mask	= 0xffffffff,
+		.platform_data		= &musb_plat,
+	},
+	.num_resources	= ARRAY_SIZE(musb_resources),
+	.resource	= musb_resources,
+};
+#endif
+
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+static struct mtd_partition ezbrd_partitions[] = {
+	{
+		.name       = "bootloader(nor)",
+		.size       = 0x40000,
+		.offset     = 0,
+	}, {
+		.name       = "linux kernel(nor)",
+		.size       = 0x1C0000,
+		.offset     = MTDPART_OFS_APPEND,
+	}, {
+		.name       = "file system(nor)",
+		.size       = MTDPART_SIZ_FULL,
+		.offset     = MTDPART_OFS_APPEND,
+	}
+};
+
+static struct physmap_flash_data ezbrd_flash_data = {
+	.width      = 2,
+	.parts      = ezbrd_partitions,
+	.nr_parts   = ARRAY_SIZE(ezbrd_partitions),
+};
+
+static struct resource ezbrd_flash_resource = {
+	.start = 0x20000000,
+	.end   = 0x203fffff,
+	.flags = IORESOURCE_MEM,
+};
+
+static struct platform_device ezbrd_flash_device = {
+	.name          = "physmap-flash",
+	.id            = 0,
+	.dev = {
+		.platform_data = &ezbrd_flash_data,
+	},
+	.num_resources = 1,
+	.resource      = &ezbrd_flash_resource,
+};
+#endif
+
+#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+static struct mtd_partition partition_info[] = {
+	{
+		.name = "linux kernel(nand)",
+		.offset = 0,
+		.size = 4 * 1024 * 1024,
+	},
+	{
+		.name = "file system(nand)",
+		.offset = MTDPART_OFS_APPEND,
+		.size = MTDPART_SIZ_FULL,
+	},
+};
+
+static struct bf5xx_nand_platform bf5xx_nand_platform = {
+	.page_size = NFC_PG_SIZE_256,
+	.data_width = NFC_NWIDTH_8,
+	.partitions = partition_info,
+	.nr_partitions = ARRAY_SIZE(partition_info),
+	.rd_dly = 3,
+	.wr_dly = 3,
+};
+
+static struct resource bf5xx_nand_resources[] = {
+	{
+		.start = NFC_CTL,
+		.end = NFC_DATA_RD + 2,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = CH_NFC,
+		.end = CH_NFC,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bf5xx_nand_device = {
+	.name = "bf5xx-nand",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bf5xx_nand_resources),
+	.resource = bf5xx_nand_resources,
+	.dev = {
+		.platform_data = &bf5xx_nand_platform,
+	},
+};
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+	.name = "rtc-bfin",
+	.id   = -1,
+};
+#endif
+
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+static struct platform_device bfin_mac_device = {
+	.name = "bfin_mac",
+};
+#endif
+
+#if defined(CONFIG_MTD_M25P80) \
+	|| defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+	{
+		.name = "bootloader(spi)",
+		.size = 0x00040000,
+		.offset = 0,
+		.mask_flags = MTD_CAP_ROM
+	}, {
+		.name = "linux kernel(spi)",
+		.size = MTDPART_SIZ_FULL,
+		.offset = MTDPART_OFS_APPEND,
+	}
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+	.name = "m25p80",
+	.parts = bfin_spi_flash_partitions,
+	.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+	.type = "m25p16",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+	.enable_dma = 0,         /* use dma transfer with this chip*/
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SPI_ADC_BF533) \
+	|| defined(CONFIG_SPI_ADC_BF533_MODULE)
+/* SPI ADC chip */
+static struct bfin5xx_spi_chip spi_adc_chip_info = {
+	.enable_dma = 1,         /* use dma transfer with this chip*/
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+	.enable_dma = 1,
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_PBX)
+static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
+	.ctl_reg	= 0x4, /* send zero */
+	.enable_dma	= 0,
+	.bits_per_word	= 8,
+	.cs_change_per_word = 1,
+};
+#endif
+
+#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+
+static const struct ad7877_platform_data bfin_ad7877_ts_info = {
+	.model			= 7877,
+	.vref_delay_usecs	= 50,	/* internal, no capacitor */
+	.x_plate_ohms		= 419,
+	.y_plate_ohms		= 486,
+	.pressure_max		= 1000,
+	.pressure_min		= 0,
+	.stopacq_polarity 	= 1,
+	.first_conversion_delay = 3,
+	.acquisition_time 	= 1,
+	.averaging 		= 1,
+	.pen_down_acc_interval 	= 1,
+};
+#endif
+
+#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
+	 && defined(CONFIG_SND_SOC_WM8731_SPI)
+static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+static struct bfin5xx_spi_chip spidev_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) \
+	|| defined(CONFIG_MTD_M25P80_MODULE)
+	{
+		/* the modalias must be the same as spi device driver name */
+		.modalias = "m25p80", /* Name of spi_driver for this device */
+		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
+		.platform_data = &bfin_spi_flash_data,
+		.controller_data = &spi_flash_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
+#if defined(CONFIG_SPI_ADC_BF533) \
+	|| defined(CONFIG_SPI_ADC_BF533_MODULE)
+	{
+		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
+		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 1, /* Framework chip select. */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.controller_data = &spi_adc_chip_info,
+	},
+#endif
+
+#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+	{
+		.modalias = "spi_mmc_dummy",
+		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 0,
+		.platform_data = NULL,
+		.controller_data = &spi_mmc_chip_info,
+		.mode = SPI_MODE_3,
+	},
+	{
+		.modalias = "spi_mmc",
+		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = CONFIG_SPI_MMC_CS_CHAN,
+		.platform_data = NULL,
+		.controller_data = &spi_mmc_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+#if defined(CONFIG_PBX)
+	{
+		.modalias = "fxs-spi",
+		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 8 - CONFIG_J11_JUMPER,
+		.controller_data = &spi_si3xxx_chip_info,
+		.mode = SPI_MODE_3,
+	},
+	{
+		.modalias = "fxo-spi",
+		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 8 - CONFIG_J19_JUMPER,
+		.controller_data = &spi_si3xxx_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+	{
+		.modalias		= "ad7877",
+		.platform_data		= &bfin_ad7877_ts_info,
+		.irq			= IRQ_PF8,
+		.max_speed_hz	= 12500000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num	= 0,
+		.chip_select  = 2,
+		.controller_data = &spi_ad7877_chip_info,
+	},
+#endif
+#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
+	 && defined(CONFIG_SND_SOC_WM8731_SPI)
+	{
+		.modalias	= "wm8731",
+		.max_speed_hz	= 3125000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num	= 0,
+		.chip_select    = 5,
+		.controller_data = &spi_wm8731_chip_info,
+		.mode = SPI_MODE_0,
+	},
+#endif
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+	{
+		.modalias = "spidev",
+		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1,
+		.controller_data = &spidev_chip_info,
+	},
+#endif
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+	{
+		.modalias = "bfin-lq035q1-spi",
+		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1,
+		.controller_data = &lq035q1_spi_chip_info,
+		.mode = SPI_CPHA | SPI_CPOL,
+	},
+#endif
+};
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* SPI controller data */
+static struct bfin5xx_spi_master bfin_spi0_info = {
+	.num_chipselect = 8,
+	.enable_dma = 1,  /* master has the ability to do dma transfer */
+	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+	[0] = {
+		.start = SPI0_REGBASE,
+		.end   = SPI0_REGBASE + 0xFF,
+		.flags = IORESOURCE_MEM,
+		},
+	[1] = {
+		.start = CH_SPI,
+		.end   = CH_SPI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_spi0_device = {
+	.name = "bfin-spi",
+	.id = 0, /* Bus number */
+	.num_resources = ARRAY_SIZE(bfin_spi0_resource),
+	.resource = bfin_spi0_resource,
+	.dev = {
+		.platform_data = &bfin_spi0_info, /* Passed to driver */
+	},
+};
+#endif  /* spi master and devices */
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	},
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+	{
+		.start = 0xFFC02000,
+		.end = 0xFFC020FF,
+		.flags = IORESOURCE_MEM,
+	},
+#endif
+};
+
+static struct platform_device bfin_uart_device = {
+	.name = "bfin-uart",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_uart_resources),
+	.resource = bfin_uart_resources,
+};
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	},
+#endif
+#ifdef CONFIG_BFIN_SIR1
+	{
+		.start = 0xFFC02000,
+		.end = 0xFFC020FF,
+		.flags = IORESOURCE_MEM,
+	},
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+	.name = "bfin_sir",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_sir_resources),
+	.resource = bfin_sir_resources,
+};
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+	[0] = {
+		.start = TWI0_REGBASE,
+		.end   = TWI0_REGBASE,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = IRQ_TWI,
+		.end   = IRQ_TWI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device i2c_bfin_twi_device = {
+	.name = "i2c-bfin-twi",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_twi0_resource),
+	.resource = bfin_twi0_resource,
+};
+#endif
+
+#ifdef CONFIG_I2C_BOARDINFO
+static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
+#if defined(CONFIG_TWI_LCD) || defined(CONFIG_TWI_LCD_MODULE)
+	{
+		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
+	},
+#endif
+#if defined(CONFIG_TWI_KEYPAD) || defined(CONFIG_TWI_KEYPAD_MODULE)
+	{
+		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
+		.irq = IRQ_PF8,
+	},
+#endif
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+static struct platform_device bfin_sport0_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 0,
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 1,
+};
+#endif
+
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#include <linux/input.h>
+#include <linux/gpio_keys.h>
+
+static struct gpio_keys_button bfin_gpio_keys_table[] = {
+	{BTN_0, GPIO_PG0, 1, "gpio-keys: BTN0"},
+	{BTN_1, GPIO_PG13, 1, "gpio-keys: BTN1"},
+};
+
+static struct gpio_keys_platform_data bfin_gpio_keys_data = {
+	.buttons        = bfin_gpio_keys_table,
+	.nbuttons       = ARRAY_SIZE(bfin_gpio_keys_table),
+};
+
+static struct platform_device bfin_device_gpiokeys = {
+	.name      = "gpio-keys",
+	.dev = {
+		.platform_data = &bfin_gpio_keys_data,
+	},
+};
+#endif
+
+static struct resource bfin_gpios_resources = {
+	.start = 0,
+	.end   = MAX_BLACKFIN_GPIOS - 1,
+	.flags = IORESOURCE_IRQ,
+};
+
+static struct platform_device bfin_gpios_device = {
+	.name = "simple-gpio",
+	.id = -1,
+	.num_resources = 1,
+	.resource = &bfin_gpios_resources,
+};
+
+static const unsigned int cclk_vlev_datasheet[] =
+{
+	VRPAIR(VLEV_100, 400000000),
+	VRPAIR(VLEV_105, 426000000),
+	VRPAIR(VLEV_110, 500000000),
+	VRPAIR(VLEV_115, 533000000),
+	VRPAIR(VLEV_120, 600000000),
+};
+
+static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
+	.tuple_tab = cclk_vlev_datasheet,
+	.tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
+	.vr_settling_time = 25 /* us */,
+};
+
+static struct platform_device bfin_dpmc = {
+	.name = "bfin dpmc",
+	.dev = {
+		.platform_data = &bfin_dmpc_vreg_data,
+	},
+};
+
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#include <asm/bfin-lq035q1.h>
+
+static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
+	.mode = 	LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
+	.use_bl = 	1,
+	.gpio_bl =	GPIO_PG12,
+};
+
+static struct resource bfin_lq035q1_resources[] = {
+	{
+		.start = IRQ_PPI_ERROR,
+		.end = IRQ_PPI_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_lq035q1_device = {
+	.name		= "bfin-lq035q1",
+	.id		= -1,
+	.num_resources 	= ARRAY_SIZE(bfin_lq035q1_resources),
+	.resource 	= bfin_lq035q1_resources,
+	.dev		= {
+		.platform_data = &bfin_lq035q1_data,
+	},
+};
+#endif
+
+static struct platform_device *stamp_devices[] __initdata = {
+
+	&bfin_dpmc,
+
+#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+	&bf5xx_nand_device,
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+	&rtc_device,
+#endif
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+	&musb_device,
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+	&bfin_mac_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	&bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+	&bfin_uart_device,
+#endif
+
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+	&bfin_lq035q1_device,
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+	&bfin_sir_device,
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+	&i2c_bfin_twi_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+	&bfin_sport0_uart_device,
+	&bfin_sport1_uart_device,
+#endif
+
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+	&bfin_device_gpiokeys,
+#endif
+
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+	&ezbrd_flash_device,
+#endif
+
+	&bfin_gpios_device,
+};
+
+static int __init stamp_init(void)
+{
+	printk(KERN_INFO "%s(): registering device resources\n", __func__);
+
+#ifdef CONFIG_I2C_BOARDINFO
+	i2c_register_board_info(0, bfin_i2c_board_info,
+				ARRAY_SIZE(bfin_i2c_board_info));
+#endif
+
+	platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
+	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+	return 0;
+}
+
+arch_initcall(stamp_init);
+
+void native_machine_restart(char *cmd)
+{
+	/* workaround reboot hang when booting from SPI */
+	if ((bfin_read_SYSCR() & 0x7) == 0x3)
+		bfin_gpio_reset_spi0_ssel1();
+}
+
+void bfin_get_ether_addr(char *addr)
+{
+	/* the MAC is stored in OTP memory page 0xDF */
+	u32 ret;
+	u64 otp_mac;
+	u32 (*otp_read)(u32 page, u32 flags, u64 *page_content) = (void *)0xEF00001A;
+
+	ret = otp_read(0xDF, 0x00, &otp_mac);
+	if (!(ret & 0x1)) {
+		char *otp_mac_p = (char *)&otp_mac;
+		for (ret = 0; ret < 6; ++ret)
+			addr[ret] = otp_mac_p[5 - ret];
+	}
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);