amd-xgbe: Move the PHY support into amd-xgbe

The AMD XGBE device is intended to work with a specific integrated PHY
and that PHY is not meant to be a standalone PHY for use by other
devices. As such this patch removes the phylib driver and implements
the PHY support in the amd-xgbe driver (the majority of the logic from
the phylib driver is moved into the amd-xgbe driver).

Update the driver version to 1.0.1.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/amd-xgbe-phy.txt

-* AMD 10GbE PHY driver (amd-xgbe-phy)
-
-Required properties:
-- compatible: Should be "amd,xgbe-phy-seattle-v1a" and
-  "ethernet-phy-ieee802.3-c45"
-- reg: Address and length of the register sets for the device
-   - SerDes Rx/Tx registers
-   - SerDes integration registers (1/2)
-   - SerDes integration registers (2/2)
-- interrupt-parent: Should be the phandle for the interrupt controller
-  that services interrupts for this device
-- interrupts: Should contain the amd-xgbe-phy interrupt.
-
-Optional properties:
-- amd,speed-set: Speed capabilities of the device
-    0 - 1GbE and 10GbE (default)
-    1 - 2.5GbE and 10GbE
-
-The following optional properties are represented by an array with each
-value corresponding to a particular speed. The first array value represents
-the setting for the 1GbE speed, the second value for the 2.5GbE speed and
-the third value for the 10GbE speed.  All three values are required if the
-property is used.
-- amd,serdes-blwc: Baseline wandering correction enablement
-    0 - Off
-    1 - On
-- amd,serdes-cdr-rate: CDR rate speed selection
-- amd,serdes-pq-skew: PQ (data sampling) skew
-- amd,serdes-tx-amp: TX amplitude boost
-- amd,serdes-dfe-tap-config: DFE taps available to run
-- amd,serdes-dfe-tap-enable: DFE taps to enable
-
-Example:
-	xgbe_phy@e1240800 {
-		compatible = "amd,xgbe-phy-seattle-v1a", "ethernet-phy-ieee802.3-c45";
-		reg = <0 0xe1240800 0 0x00400>,
-		      <0 0xe1250000 0 0x00060>,
-		      <0 0xe1250080 0 0x00004>;
-		interrupt-parent = <&gic>;
-		interrupts = <0 323 4>;
-		amd,speed-set = <0>;
-		amd,serdes-blwc = <1>, <1>, <0>;
-		amd,serdes-cdr-rate = <2>, <2>, <7>;
-		amd,serdes-pq-skew = <10>, <10>, <30>;
-		amd,serdes-tx-amp = <15>, <15>, <10>;
-		amd,serdes-dfe-tap-config = <3>, <3>, <1>;
-		amd,serdes-dfe-tap-enable = <0>, <0>, <127>;
-	};

Documentation/devicetree/bindings/net/amd-xgbe.txt

 * AMD 10GbE driver (amd-xgbe)
 
-Required properties:
+Required properties (ethernet device):
 - compatible: Should be "amd,xgbe-seattle-v1a"
 - reg: Address and length of the register sets for the device
    - MAC registers
@@ -22,7 +22,7 @@ Required properties:
 - phy-handle: See ethernet.txt file in the same directory
 - phy-mode: See ethernet.txt file in the same directory
 
-Optional properties:
+Optional properties (ethernet device):
 - mac-address: mac address to be assigned to the device. Can be overridden
   by UEFI.
 - dma-coherent: Present if dma operations are coherent
@@ -30,6 +30,35 @@ Optional properties:
   a unique interrupt for each DMA channel - this requires an additional
   interrupt be configured for each DMA channel
 
+Required properties (phy device):
+- compatible: Should be "amd,xgbe-phy-seattle-v1a"
+- reg: Address and length of the register sets for the device
+   - SerDes Rx/Tx registers
+   - SerDes integration registers (1/2)
+   - SerDes integration registers (2/2)
+- interrupt-parent: Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- interrupts: Should contain the amd-xgbe-phy interrupt.
+
+Optional properties (phy device):
+- amd,speed-set: Speed capabilities of the device
+    0 - 1GbE and 10GbE (default)
+    1 - 2.5GbE and 10GbE
+
+The following optional properties are represented by an array with each
+value corresponding to a particular speed. The first array value represents
+the setting for the 1GbE speed, the second value for the 2.5GbE speed and
+the third value for the 10GbE speed.  All three values are required if the
+property is used.
+- amd,serdes-blwc: Baseline wandering correction enablement
+    0 - Off
+    1 - On
+- amd,serdes-cdr-rate: CDR rate speed selection
+- amd,serdes-pq-skew: PQ (data sampling) skew
+- amd,serdes-tx-amp: TX amplitude boost
+- amd,serdes-dfe-tap-config: DFE taps available to run
+- amd,serdes-dfe-tap-enable: DFE taps to enable
+
 Example:
 	xgbe@e0700000 {
 		compatible = "amd,xgbe-seattle-v1a";
@@ -41,7 +70,23 @@ Example:
 		amd,per-channel-interrupt;
 		clocks = <&xgbe_dma_clk>, <&xgbe_ptp_clk>;
 		clock-names = "dma_clk", "ptp_clk";
-		phy-handle = <&phy>;
+		phy-handle = <&xgbe_phy>;
 		phy-mode = "xgmii";
 		mac-address = [ 02 a1 a2 a3 a4 a5 ];
 	};
+
+	xgbe_phy@e1240800 {
+		compatible = "amd,xgbe-phy-seattle-v1a";
+		reg = <0 0xe1240800 0 0x00400>,
+		      <0 0xe1250000 0 0x00060>,
+		      <0 0xe1250080 0 0x00004>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 323 4>;
+		amd,speed-set = <0>;
+		amd,serdes-blwc = <1>, <1>, <0>;
+		amd,serdes-cdr-rate = <2>, <2>, <7>;
+		amd,serdes-pq-skew = <10>, <10>, <30>;
+		amd,serdes-tx-amp = <15>, <15>, <10>;
+		amd,serdes-dfe-tap-config = <3>, <3>, <1>;
+		amd,serdes-dfe-tap-enable = <0>, <0>, <127>;
+	};

MAINTAINERS

@@ -652,7 +652,6 @@ M:	Tom Lendacky <thomas.lendacky@amd.com>
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/ethernet/amd/xgbe/
-F:	drivers/net/phy/amd-xgbe-phy.c
 
 AMS (Apple Motion Sensor) DRIVER
 M:	Michael Hanselmann <linux-kernel@hansmi.ch>

drivers/net/ethernet/amd/Kconfig

@@ -179,10 +179,8 @@ config SUNLANCE
 
 config AMD_XGBE
 	tristate "AMD 10GbE Ethernet driver"
-	depends on (OF_NET || ACPI) && HAS_IOMEM && HAS_DMA
+	depends on ((OF_NET && OF_ADDRESS) || ACPI) && HAS_IOMEM && HAS_DMA
 	depends on ARM64 || COMPILE_TEST
-	select PHYLIB
-	select AMD_XGBE_PHY
 	select BITREVERSE
 	select CRC32
 	select PTP_1588_CLOCK

drivers/net/ethernet/amd/xgbe/xgbe-common.h

@@ -857,6 +857,48 @@
  */
 #define PCS_MMD_SELECT			0xff
 
+/* SerDes integration register offsets */
+#define SIR0_KR_RT_1			0x002c
+#define SIR0_STATUS			0x0040
+#define SIR1_SPEED			0x0000
+
+/* SerDes integration register entry bit positions and sizes */
+#define SIR0_KR_RT_1_RESET_INDEX	11
+#define SIR0_KR_RT_1_RESET_WIDTH	1
+#define SIR0_STATUS_RX_READY_INDEX	0
+#define SIR0_STATUS_RX_READY_WIDTH	1
+#define SIR0_STATUS_TX_READY_INDEX	8
+#define SIR0_STATUS_TX_READY_WIDTH	1
+#define SIR1_SPEED_CDR_RATE_INDEX	12
+#define SIR1_SPEED_CDR_RATE_WIDTH	4
+#define SIR1_SPEED_DATARATE_INDEX	4
+#define SIR1_SPEED_DATARATE_WIDTH	2
+#define SIR1_SPEED_PLLSEL_INDEX		3
+#define SIR1_SPEED_PLLSEL_WIDTH		1
+#define SIR1_SPEED_RATECHANGE_INDEX	6
+#define SIR1_SPEED_RATECHANGE_WIDTH	1
+#define SIR1_SPEED_TXAMP_INDEX		8
+#define SIR1_SPEED_TXAMP_WIDTH		4
+#define SIR1_SPEED_WORDMODE_INDEX	0
+#define SIR1_SPEED_WORDMODE_WIDTH	3
+
+/* SerDes RxTx register offsets */
+#define RXTX_REG6			0x0018
+#define RXTX_REG20			0x0050
+#define RXTX_REG22			0x0058
+#define RXTX_REG114			0x01c8
+#define RXTX_REG129			0x0204
+
+/* SerDes RxTx register entry bit positions and sizes */
+#define RXTX_REG6_RESETB_RXD_INDEX	8
+#define RXTX_REG6_RESETB_RXD_WIDTH	1
+#define RXTX_REG20_BLWC_ENA_INDEX	2
+#define RXTX_REG20_BLWC_ENA_WIDTH	1
+#define RXTX_REG114_PQ_REG_INDEX	9
+#define RXTX_REG114_PQ_REG_WIDTH	7
+#define RXTX_REG129_RXDFE_CONFIG_INDEX	14
+#define RXTX_REG129_RXDFE_CONFIG_WIDTH	2
+
 /* Descriptor/Packet entry bit positions and sizes */
 #define RX_PACKET_ERRORS_CRC_INDEX		2
 #define RX_PACKET_ERRORS_CRC_WIDTH		1
@@ -973,10 +1015,47 @@
 #define TX_NORMAL_DESC2_VLAN_INSERT		0x2
 
 /* MDIO undefined or vendor specific registers */
+#ifndef MDIO_PMA_10GBR_PMD_CTRL
+#define MDIO_PMA_10GBR_PMD_CTRL		0x0096
+#endif
+
+#ifndef MDIO_PMA_10GBR_FECCTRL
+#define MDIO_PMA_10GBR_FECCTRL		0x00ab
+#endif
+
+#ifndef MDIO_AN_XNP
+#define MDIO_AN_XNP			0x0016
+#endif
+
+#ifndef MDIO_AN_LPX
+#define MDIO_AN_LPX			0x0019
+#endif
+
 #ifndef MDIO_AN_COMP_STAT
 #define MDIO_AN_COMP_STAT		0x0030
 #endif
 
+#ifndef MDIO_AN_INTMASK
+#define MDIO_AN_INTMASK			0x8001
+#endif
+
+#ifndef MDIO_AN_INT
+#define MDIO_AN_INT			0x8002
+#endif
+
+#ifndef MDIO_CTRL1_SPEED1G
+#define MDIO_CTRL1_SPEED1G		(MDIO_CTRL1_SPEED10G & ~BMCR_SPEED100)
+#endif
+
+/* MDIO mask values */
+#define XGBE_XNP_MCF_NULL_MESSAGE	0x001
+#define XGBE_XNP_ACK_PROCESSED		BIT(12)
+#define XGBE_XNP_MP_FORMATTED		BIT(13)
+#define XGBE_XNP_NP_EXCHANGE		BIT(15)
+
+#define XGBE_KR_TRAINING_START		BIT(0)
+#define XGBE_KR_TRAINING_ENABLE		BIT(1)
+
 /* Bit setting and getting macros
  *  The get macro will extract the current bit field value from within
  *  the variable
@@ -1118,6 +1197,82 @@ do {									\
 #define XPCS_IOREAD(_pdata, _off)					\
 	ioread32((_pdata)->xpcs_regs + (_off))
 
+/* Macros for building, reading or writing register values or bits
+ * within the register values of SerDes integration registers.
+ */
+#define XSIR_GET_BITS(_var, _prefix, _field)                            \
+	GET_BITS((_var),                                                \
+		 _prefix##_##_field##_INDEX,                            \
+		 _prefix##_##_field##_WIDTH)
+
+#define XSIR_SET_BITS(_var, _prefix, _field, _val)                      \
+	SET_BITS((_var),                                                \
+		 _prefix##_##_field##_INDEX,                            \
+		 _prefix##_##_field##_WIDTH, (_val))
+
+#define XSIR0_IOREAD(_pdata, _reg)					\
+	ioread16((_pdata)->sir0_regs + _reg)
+
+#define XSIR0_IOREAD_BITS(_pdata, _reg, _field)				\
+	GET_BITS(XSIR0_IOREAD((_pdata), _reg),				\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH)
+
+#define XSIR0_IOWRITE(_pdata, _reg, _val)				\
+	iowrite16((_val), (_pdata)->sir0_regs + _reg)
+
+#define XSIR0_IOWRITE_BITS(_pdata, _reg, _field, _val)			\
+do {									\
+	u16 reg_val = XSIR0_IOREAD((_pdata), _reg);			\
+	SET_BITS(reg_val,						\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH, (_val));			\
+	XSIR0_IOWRITE((_pdata), _reg, reg_val);				\
+} while (0)
+
+#define XSIR1_IOREAD(_pdata, _reg)					\
+	ioread16((_pdata)->sir1_regs + _reg)
+
+#define XSIR1_IOREAD_BITS(_pdata, _reg, _field)				\
+	GET_BITS(XSIR1_IOREAD((_pdata), _reg),				\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH)
+
+#define XSIR1_IOWRITE(_pdata, _reg, _val)				\
+	iowrite16((_val), (_pdata)->sir1_regs + _reg)
+
+#define XSIR1_IOWRITE_BITS(_pdata, _reg, _field, _val)			\
+do {									\
+	u16 reg_val = XSIR1_IOREAD((_pdata), _reg);			\
+	SET_BITS(reg_val,						\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH, (_val));			\
+	XSIR1_IOWRITE((_pdata), _reg, reg_val);				\
+} while (0)
+
+/* Macros for building, reading or writing register values or bits
+ * within the register values of SerDes RxTx registers.
+ */
+#define XRXTX_IOREAD(_pdata, _reg)					\
+	ioread16((_pdata)->rxtx_regs + _reg)
+
+#define XRXTX_IOREAD_BITS(_pdata, _reg, _field)				\
+	GET_BITS(XRXTX_IOREAD((_pdata), _reg),				\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH)
+
+#define XRXTX_IOWRITE(_pdata, _reg, _val)				\
+	iowrite16((_val), (_pdata)->rxtx_regs + _reg)
+
+#define XRXTX_IOWRITE_BITS(_pdata, _reg, _field, _val)			\
+do {									\
+	u16 reg_val = XRXTX_IOREAD((_pdata), _reg);			\
+	SET_BITS(reg_val,						\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH, (_val));			\
+	XRXTX_IOWRITE((_pdata), _reg, reg_val);				\
+} while (0)
+
 /* Macros for building, reading or writing register values or bits
  * using MDIO.  Different from above because of the use of standardized
  * Linux include values.  No shifting is performed with the bit

drivers/net/ethernet/amd/xgbe/xgbe-dev.c

@@ -910,23 +910,6 @@ static void xgbe_write_mmd_regs(struct xgbe_prv_data *pdata, int prtad,
 	else
 		mmd_address = (pdata->mdio_mmd << 16) | (mmd_reg & 0xffff);
 
-	/* If the PCS is changing modes, match the MAC speed to it */
-	if (((mmd_address >> 16) == MDIO_MMD_PCS) &&
-	    ((mmd_address & 0xffff) == MDIO_CTRL2)) {
-		struct phy_device *phydev = pdata->phydev;
-
-		if (mmd_data & MDIO_PCS_CTRL2_TYPE) {
-			/* KX mode */
-			if (phydev->supported & SUPPORTED_1000baseKX_Full)
-				xgbe_set_gmii_speed(pdata);
-			else
-				xgbe_set_gmii_2500_speed(pdata);
-		} else {
-			/* KR mode */
-			xgbe_set_xgmii_speed(pdata);
-		}
-	}
-
 	/* The PCS registers are accessed using mmio. The underlying APB3
 	 * management interface uses indirect addressing to access the MMD
 	 * register sets. This requires accessing of the PCS register in two

drivers/net/ethernet/amd/xgbe/xgbe-drv.c

@@ -437,12 +437,31 @@ static void xgbe_tx_timer(unsigned long data)
 	DBGPR("<--xgbe_tx_timer\n");
 }
 
-static void xgbe_init_tx_timers(struct xgbe_prv_data *pdata)
+static void xgbe_service(struct work_struct *work)
+{
+	struct xgbe_prv_data *pdata = container_of(work,
+						   struct xgbe_prv_data,
+						   service_work);
+
+	pdata->phy_if.phy_status(pdata);
+}
+
+static void xgbe_service_timer(unsigned long data)
+{
+	struct xgbe_prv_data *pdata = (struct xgbe_prv_data *)data;
+
+	schedule_work(&pdata->service_work);
+
+	mod_timer(&pdata->service_timer, jiffies + HZ);
+}
+
+static void xgbe_init_timers(struct xgbe_prv_data *pdata)
 {
 	struct xgbe_channel *channel;
 	unsigned int i;
 
-	DBGPR("-->xgbe_init_tx_timers\n");
+	setup_timer(&pdata->service_timer, xgbe_service_timer,
+		    (unsigned long)pdata);
 
 	channel = pdata->channel;
 	for (i = 0; i < pdata->channel_count; i++, channel++) {
@@ -452,16 +471,19 @@ static void xgbe_init_tx_timers(struct xgbe_prv_data *pdata)
 		setup_timer(&channel->tx_timer, xgbe_tx_timer,
 			    (unsigned long)channel);
 	}
+}
 
-	DBGPR("<--xgbe_init_tx_timers\n");
+static void xgbe_start_timers(struct xgbe_prv_data *pdata)
+{
+	mod_timer(&pdata->service_timer, jiffies + HZ);
 }
 
-static void xgbe_stop_tx_timers(struct xgbe_prv_data *pdata)
+static void xgbe_stop_timers(struct xgbe_prv_data *pdata)
 {
 	struct xgbe_channel *channel;
 	unsigned int i;
 
-	DBGPR("-->xgbe_stop_tx_timers\n");
+	del_timer_sync(&pdata->service_timer);
 
 	channel = pdata->channel;
 	for (i = 0; i < pdata->channel_count; i++, channel++) {
@@ -470,8 +492,6 @@ static void xgbe_stop_tx_timers(struct xgbe_prv_data *pdata)
 
 		del_timer_sync(&channel->tx_timer);
 	}
-
-	DBGPR("<--xgbe_stop_tx_timers\n");
 }
 
 void xgbe_get_all_hw_features(struct xgbe_prv_data *pdata)
@@ -758,113 +778,14 @@ static void xgbe_free_rx_data(struct xgbe_prv_data *pdata)
 	DBGPR("<--xgbe_free_rx_data\n");
 }
 
-static void xgbe_adjust_link(struct net_device *netdev)
-{
-	struct xgbe_prv_data *pdata = netdev_priv(netdev);
-	struct xgbe_hw_if *hw_if = &pdata->hw_if;
-	struct phy_device *phydev = pdata->phydev;
-	int new_state = 0;
-
-	if (!phydev)
-		return;
-
-	if (phydev->link) {
-		/* Flow control support */
-		if (pdata->pause_autoneg) {
-			if (phydev->pause || phydev->asym_pause) {
-				pdata->tx_pause = 1;
-				pdata->rx_pause = 1;
-			} else {
-				pdata->tx_pause = 0;
-				pdata->rx_pause = 0;
-			}
-		}
-
-		if (pdata->tx_pause != pdata->phy_tx_pause) {
-			hw_if->config_tx_flow_control(pdata);
-			pdata->phy_tx_pause = pdata->tx_pause;
-		}
-
-		if (pdata->rx_pause != pdata->phy_rx_pause) {
-			hw_if->config_rx_flow_control(pdata);
-			pdata->phy_rx_pause = pdata->rx_pause;
-		}
-
-		/* Speed support */
-		if (phydev->speed != pdata->phy_speed) {
-			new_state = 1;
-
-			switch (phydev->speed) {
-			case SPEED_10000:
-				hw_if->set_xgmii_speed(pdata);
-				break;
-
-			case SPEED_2500:
-				hw_if->set_gmii_2500_speed(pdata);
-				break;
-
-			case SPEED_1000:
-				hw_if->set_gmii_speed(pdata);
-				break;
-			}
-			pdata->phy_speed = phydev->speed;
-		}
-
-		if (phydev->link != pdata->phy_link) {
-			new_state = 1;
-			pdata->phy_link = 1;
-		}
-	} else if (pdata->phy_link) {
-		new_state = 1;
-		pdata->phy_link = 0;
-		pdata->phy_speed = SPEED_UNKNOWN;
-	}
-
-	if (new_state)
-		phy_print_status(phydev);
-}
-
 static int xgbe_phy_init(struct xgbe_prv_data *pdata)
 {
-	struct net_device *netdev = pdata->netdev;
-	struct phy_device *phydev = pdata->phydev;
-	int ret;
-
 	pdata->phy_link = -1;
 	pdata->phy_speed = SPEED_UNKNOWN;
 	pdata->phy_tx_pause = pdata->tx_pause;
 	pdata->phy_rx_pause = pdata->rx_pause;
 
-	ret = phy_connect_direct(netdev, phydev, &xgbe_adjust_link,
-				 pdata->phy_mode);
-	if (ret) {
-		netdev_err(netdev, "phy_connect_direct failed\n");
-		return ret;
-	}
-
-	if (!phydev->drv || (phydev->drv->phy_id == 0)) {
-		netdev_err(netdev, "phy_id not valid\n");
-		ret = -ENODEV;
-		goto err_phy_connect;
-	}
-	netif_dbg(pdata, ifup, pdata->netdev,
-		  "phy_connect_direct succeeded for PHY %s\n",
-		  dev_name(&phydev->dev));
-
-	return 0;
-
-err_phy_connect:
-	phy_disconnect(phydev);
-
-	return ret;
-}
-
-static void xgbe_phy_exit(struct xgbe_prv_data *pdata)
-{
-	if (!pdata->phydev)
-		return;
-
-	phy_disconnect(pdata->phydev);
+	return pdata->phy_if.phy_reset(pdata);
 }
 
 int xgbe_powerdown(struct net_device *netdev, unsigned int caller)
@@ -889,13 +810,14 @@ int xgbe_powerdown(struct net_device *netdev, unsigned int caller)
 
 	netif_tx_stop_all_queues(netdev);
 
+	xgbe_stop_timers(pdata);
+	flush_workqueue(pdata->dev_workqueue);
+
 	hw_if->powerdown_tx(pdata);
 	hw_if->powerdown_rx(pdata);
 
 	xgbe_napi_disable(pdata, 0);
 
-	phy_stop(pdata->phydev);
-
 	pdata->power_down = 1;
 
 	spin_unlock_irqrestore(&pdata->lock, flags);
@@ -924,8 +846,6 @@ int xgbe_powerup(struct net_device *netdev, unsigned int caller)
 
 	pdata->power_down = 0;
 
-	phy_start(pdata->phydev);
-
 	xgbe_napi_enable(pdata, 0);
 
 	hw_if->powerup_tx(pdata);
@@ -936,6 +856,8 @@ int xgbe_powerup(struct net_device *netdev, unsigned int caller)
 
 	netif_tx_start_all_queues(netdev);
 
+	xgbe_start_timers(pdata);
+
 	spin_unlock_irqrestore(&pdata->lock, flags);
 
 	DBGPR("<--xgbe_powerup\n");
@@ -946,6 +868,7 @@ int xgbe_powerup(struct net_device *netdev, unsigned int caller)
 static int xgbe_start(struct xgbe_prv_data *pdata)
 {
 	struct xgbe_hw_if *hw_if = &pdata->hw_if;
+	struct xgbe_phy_if *phy_if = &pdata->phy_if;
 	struct net_device *netdev = pdata->netdev;
 	int ret;
 
@@ -953,7 +876,9 @@ static int xgbe_start(struct xgbe_prv_data *pdata)
 
 	hw_if->init(pdata);
 
-	phy_start(pdata->phydev);
+	ret = phy_if->phy_start(pdata);
+	if (ret)
+		goto err_phy;
 
 	xgbe_napi_enable(pdata, 1);
 
@@ -964,10 +889,11 @@ static int xgbe_start(struct xgbe_prv_data *pdata)
 	hw_if->enable_tx(pdata);
 	hw_if->enable_rx(pdata);
 
-	xgbe_init_tx_timers(pdata);
-
 	netif_tx_start_all_queues(netdev);
 
+	xgbe_start_timers(pdata);
+	schedule_work(&pdata->service_work);
+
 	DBGPR("<--xgbe_start\n");
 
 	return 0;
@@ -975,8 +901,9 @@ static int xgbe_start(struct xgbe_prv_data *pdata)
 err_napi:
 	xgbe_napi_disable(pdata, 1);
 
-	phy_stop(pdata->phydev);
+	phy_if->phy_stop(pdata);
 
+err_phy:
 	hw_if->exit(pdata);
 
 	return ret;
@@ -985,6 +912,7 @@ static int xgbe_start(struct xgbe_prv_data *pdata)
 static void xgbe_stop(struct xgbe_prv_data *pdata)
 {
 	struct xgbe_hw_if *hw_if = &pdata->hw_if;
+	struct xgbe_phy_if *phy_if = &pdata->phy_if;
 	struct xgbe_channel *channel;
 	struct net_device *netdev = pdata->netdev;
 	struct netdev_queue *txq;
@@ -994,7 +922,8 @@ static void xgbe_stop(struct xgbe_prv_data *pdata)
 
 	netif_tx_stop_all_queues(netdev);
 
-	xgbe_stop_tx_timers(pdata);
+	xgbe_stop_timers(pdata);
+	flush_workqueue(pdata->dev_workqueue);
 
 	hw_if->disable_tx(pdata);
 	hw_if->disable_rx(pdata);
@@ -1003,7 +932,7 @@ static void xgbe_stop(struct xgbe_prv_data *pdata)
 
 	xgbe_napi_disable(pdata, 1);
 
-	phy_stop(pdata->phydev);
+	phy_if->phy_stop(pdata);
 
 	hw_if->exit(pdata);
 
@@ -1374,7 +1303,7 @@ static int xgbe_open(struct net_device *netdev)
 	ret = clk_prepare_enable(pdata->sysclk);
 	if (ret) {
 		netdev_alert(netdev, "dma clk_prepare_enable failed\n");
-		goto err_phy_init;
+		return ret;
 	}
 
 	ret = clk_prepare_enable(pdata->ptpclk);
@@ -1399,14 +1328,17 @@ static int xgbe_open(struct net_device *netdev)
 	if (ret)
 		goto err_channels;
 
-	/* Initialize the device restart and Tx timestamp work struct */
+	INIT_WORK(&pdata->service_work, xgbe_service);
 	INIT_WORK(&pdata->restart_work, xgbe_restart);
 	INIT_WORK(&pdata->tx_tstamp_work, xgbe_tx_tstamp);
+	xgbe_init_timers(pdata);
 
 	ret = xgbe_start(pdata);
 	if (ret)
 		goto err_rings;
 
+	clear_bit(XGBE_DOWN, &pdata->dev_state);
+
 	DBGPR("<--xgbe_open\n");
 
 	return 0;
@@ -1423,9 +1355,6 @@ static int xgbe_open(struct net_device *netdev)
 err_sysclk:
 	clk_disable_unprepare(pdata->sysclk);
 
-err_phy_init:
-	xgbe_phy_exit(pdata);
-
 	return ret;
 }
 
@@ -1449,8 +1378,7 @@ static int xgbe_close(struct net_device *netdev)
 	clk_disable_unprepare(pdata->ptpclk);
 	clk_disable_unprepare(pdata->sysclk);
 
-	/* Release the phy */
-	xgbe_phy_exit(pdata);
+	set_bit(XGBE_DOWN, &pdata->dev_state);
 
 	DBGPR("<--xgbe_close\n");
 

drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c

@@ -258,7 +258,6 @@ static int xgbe_set_pauseparam(struct net_device *netdev,
 			       struct ethtool_pauseparam *pause)
 {
 	struct xgbe_prv_data *pdata = netdev_priv(netdev);
-	struct phy_device *phydev = pdata->phydev;
 	int ret = 0;
 
 	DBGPR("-->xgbe_set_pauseparam\n");
@@ -268,19 +267,19 @@ static int xgbe_set_pauseparam(struct net_device *netdev,
 
 	pdata->pause_autoneg = pause->autoneg;
 	if (pause->autoneg) {
-		phydev->advertising |= ADVERTISED_Pause;
-		phydev->advertising |= ADVERTISED_Asym_Pause;
+		pdata->phy.advertising |= ADVERTISED_Pause;
+		pdata->phy.advertising |= ADVERTISED_Asym_Pause;
 
 	} else {
-		phydev->advertising &= ~ADVERTISED_Pause;
-		phydev->advertising &= ~ADVERTISED_Asym_Pause;
+		pdata->phy.advertising &= ~ADVERTISED_Pause;
+		pdata->phy.advertising &= ~ADVERTISED_Asym_Pause;
 
 		pdata->tx_pause = pause->tx_pause;
 		pdata->rx_pause = pause->rx_pause;
 	}
 
 	if (netif_running(netdev))
-		ret = phy_start_aneg(phydev);
+		ret = pdata->phy_if.phy_config_aneg(pdata);
 
 	DBGPR("<--xgbe_set_pauseparam\n");
 
@@ -291,36 +290,39 @@ static int xgbe_get_settings(struct net_device *netdev,
 			     struct ethtool_cmd *cmd)
 {
 	struct xgbe_prv_data *pdata = netdev_priv(netdev);
-	int ret;
 
 	DBGPR("-->xgbe_get_settings\n");
 
-	if (!pdata->phydev)
-		return -ENODEV;
+	cmd->phy_address = pdata->phy.address;
+
+	cmd->supported = pdata->phy.supported;
+	cmd->advertising = pdata->phy.advertising;
+	cmd->lp_advertising = pdata->phy.lp_advertising;
+
+	cmd->autoneg = pdata->phy.autoneg;
+	ethtool_cmd_speed_set(cmd, pdata->phy.speed);
+	cmd->duplex = pdata->phy.duplex;
 
-	ret = phy_ethtool_gset(pdata->phydev, cmd);
+	cmd->port = PORT_NONE;
+	cmd->transceiver = XCVR_INTERNAL;
 
 	DBGPR("<--xgbe_get_settings\n");
 
-	return ret;
+	return 0;
 }
 
 static int xgbe_set_settings(struct net_device *netdev,
 			     struct ethtool_cmd *cmd)
 {
 	struct xgbe_prv_data *pdata = netdev_priv(netdev);
-	struct phy_device *phydev = pdata->phydev;
 	u32 speed;
 	int ret;
 
 	DBGPR("-->xgbe_set_settings\n");
 
-	if (!pdata->phydev)
-		return -ENODEV;
-
 	speed = ethtool_cmd_speed(cmd);
 
-	if (cmd->phy_address != phydev->addr)
+	if (cmd->phy_address != pdata->phy.address)
 		return -EINVAL;
 
 	if ((cmd->autoneg != AUTONEG_ENABLE) &&
@@ -341,23 +343,23 @@ static int xgbe_set_settings(struct net_device *netdev,
 			return -EINVAL;
 	}
 
-	cmd->advertising &= phydev->supported;
+	cmd->advertising &= pdata->phy.supported;
 	if ((cmd->autoneg == AUTONEG_ENABLE) && !cmd->advertising)
 		return -EINVAL;
 
 	ret = 0;
-	phydev->autoneg = cmd->autoneg;
-	phydev->speed = speed;
-	phydev->duplex = cmd->duplex;
-	phydev->advertising = cmd->advertising;
+	pdata->phy.autoneg = cmd->autoneg;
+	pdata->phy.speed = speed;
+	pdata->phy.duplex = cmd->duplex;
+	pdata->phy.advertising = cmd->advertising;
 
 	if (cmd->autoneg == AUTONEG_ENABLE)
-		phydev->advertising |= ADVERTISED_Autoneg;
+		pdata->phy.advertising |= ADVERTISED_Autoneg;
 	else
-		phydev->advertising &= ~ADVERTISED_Autoneg;
+		pdata->phy.advertising &= ~ADVERTISED_Autoneg;
 
 	if (netif_running(netdev))
-		ret = phy_start_aneg(phydev);
+		ret = pdata->phy_if.phy_config_aneg(pdata);
 
 	DBGPR("<--xgbe_set_settings\n");
 

drivers/net/ethernet/amd/xgbe/xgbe-main.c

@@ -124,9 +124,11 @@
 #include <linux/of.h>
 #include <linux/of_net.h>
 #include <linux/of_address.h>
+#include <linux/of_platform.h>
 #include <linux/clk.h>
 #include <linux/property.h>
 #include <linux/acpi.h>
+#include <linux/mdio.h>
 
 #include "xgbe.h"
 #include "xgbe-common.h"
@@ -143,6 +145,42 @@ MODULE_PARM_DESC(debug, " Network interface message level setting");
 static const u32 default_msg_level = (NETIF_MSG_LINK | NETIF_MSG_IFDOWN |
 				      NETIF_MSG_IFUP);
 
+static const u32 xgbe_serdes_blwc[] = {
+	XGBE_SPEED_1000_BLWC,
+	XGBE_SPEED_2500_BLWC,
+	XGBE_SPEED_10000_BLWC,
+};
+
+static const u32 xgbe_serdes_cdr_rate[] = {
+	XGBE_SPEED_1000_CDR,
+	XGBE_SPEED_2500_CDR,
+	XGBE_SPEED_10000_CDR,
+};
+
+static const u32 xgbe_serdes_pq_skew[] = {
+	XGBE_SPEED_1000_PQ,
+	XGBE_SPEED_2500_PQ,
+	XGBE_SPEED_10000_PQ,
+};
+
+static const u32 xgbe_serdes_tx_amp[] = {
+	XGBE_SPEED_1000_TXAMP,
+	XGBE_SPEED_2500_TXAMP,
+	XGBE_SPEED_10000_TXAMP,
+};
+
+static const u32 xgbe_serdes_dfe_tap_cfg[] = {
+	XGBE_SPEED_1000_DFE_TAP_CONFIG,
+	XGBE_SPEED_2500_DFE_TAP_CONFIG,
+	XGBE_SPEED_10000_DFE_TAP_CONFIG,
+};
+
+static const u32 xgbe_serdes_dfe_tap_ena[] = {
+	XGBE_SPEED_1000_DFE_TAP_ENABLE,
+	XGBE_SPEED_2500_DFE_TAP_ENABLE,
+	XGBE_SPEED_10000_DFE_TAP_ENABLE,
+};
+
 static void xgbe_default_config(struct xgbe_prv_data *pdata)
 {
 	DBGPR("-->xgbe_default_config\n");
@@ -160,8 +198,6 @@ static void xgbe_default_config(struct xgbe_prv_data *pdata)
 	pdata->rx_pause = 1;
 	pdata->phy_speed = SPEED_UNKNOWN;
 	pdata->power_down = 0;
-	pdata->default_autoneg = AUTONEG_ENABLE;
-	pdata->default_speed = SPEED_10000;
 
 	DBGPR("<--xgbe_default_config\n");
 }
@@ -169,6 +205,7 @@ static void xgbe_default_config(struct xgbe_prv_data *pdata)
 static void xgbe_init_all_fptrs(struct xgbe_prv_data *pdata)
 {
 	xgbe_init_function_ptrs_dev(&pdata->hw_if);
+	xgbe_init_function_ptrs_phy(&pdata->phy_if);
 	xgbe_init_function_ptrs_desc(&pdata->desc_if);
 }
 
@@ -255,23 +292,75 @@ static int xgbe_of_support(struct xgbe_prv_data *pdata)
 
 	return 0;
 }
+
+static struct platform_device *xgbe_of_get_phy_pdev(struct xgbe_prv_data *pdata)
+{
+	struct device *dev = pdata->dev;
+	struct device_node *phy_node;
+	struct platform_device *phy_pdev;
+
+	phy_node = of_parse_phandle(dev->of_node, "phy-handle", 0);
+	if (!phy_node) {
+		dev_err(dev, "unable to locate phy device\n");
+		return NULL;
+	}
+
+	phy_pdev = of_find_device_by_node(phy_node);
+	of_node_put(phy_node);
+
+	return phy_pdev;
+}
 #else   /* CONFIG_OF */
 static int xgbe_of_support(struct xgbe_prv_data *pdata)
 {
 	return -EINVAL;
 }
-#endif  /*CONFIG_OF */
+
+static struct platform_device *xgbe_of_get_phy_pdev(struct xgbe_prv_data *pdata)
+{
+	return NULL;
+}
+#endif  /* CONFIG_OF */
+
+static unsigned int xgbe_resource_count(struct platform_device *pdev,
+					unsigned int type)
+{
+	unsigned int count;
+	int i;
+
+	for (i = 0, count = 0; i < pdev->num_resources; i++) {
+		struct resource *res = &pdev->resource[i];
+
+		if (type == resource_type(res))
+			count++;
+	}
+
+	return count;
+}
+
+static struct platform_device *xgbe_get_phy_pdev(struct xgbe_prv_data *pdata)
+{
+	struct platform_device *phy_pdev;
+
+	if (pdata->use_acpi) {
+		get_device(pdata->dev);
+		phy_pdev = pdata->pdev;
+	} else {
+		phy_pdev = xgbe_of_get_phy_pdev(pdata);
+	}
+
+	return phy_pdev;
+}
 
 static int xgbe_probe(struct platform_device *pdev)
 {
 	struct xgbe_prv_data *pdata;
-	struct xgbe_hw_if *hw_if;
-	struct xgbe_desc_if *desc_if;
 	struct net_device *netdev;
-	struct device *dev = &pdev->dev;
+	struct device *dev = &pdev->dev, *phy_dev;
+	struct platform_device *phy_pdev;
 	struct resource *res;
 	const char *phy_mode;
-	unsigned int i;
+	unsigned int i, phy_memnum, phy_irqnum;
 	int ret;
 
 	DBGPR("--> xgbe_probe\n");
@@ -298,9 +387,34 @@ static int xgbe_probe(struct platform_device *pdev)
 
 	pdata->msg_enable = netif_msg_init(debug, default_msg_level);
 
+	set_bit(XGBE_DOWN, &pdata->dev_state);
+
 	/* Check if we should use ACPI or DT */
 	pdata->use_acpi = (!pdata->adev || acpi_disabled) ? 0 : 1;
 
+	phy_pdev = xgbe_get_phy_pdev(pdata);
+	if (!phy_pdev) {
+		dev_err(dev, "unable to obtain phy device\n");
+		ret = -EINVAL;
+		goto err_phydev;
+	}
+	phy_dev = &phy_pdev->dev;
+
+	if (pdev == phy_pdev) {
+		/* ACPI:
+		 *   The XGBE and PHY resources are grouped together with
+		 *   the PHY resources listed last
+		 */
+		phy_memnum = xgbe_resource_count(pdev, IORESOURCE_MEM) - 3;
+		phy_irqnum = xgbe_resource_count(pdev, IORESOURCE_IRQ) - 1;
+	} else {
+		/* Device tree:
+		 *   The XGBE and PHY resources are separate
+		 */
+		phy_memnum = 0;
+		phy_irqnum = 0;
+	}
+
 	/* Set and validate the number of descriptors for a ring */
 	BUILD_BUG_ON_NOT_POWER_OF_2(XGBE_TX_DESC_CNT);
 	pdata->tx_desc_count = XGBE_TX_DESC_CNT;
@@ -340,6 +454,36 @@ static int xgbe_probe(struct platform_device *pdev)
 	if (netif_msg_probe(pdata))
 		dev_dbg(dev, "xpcs_regs  = %p\n", pdata->xpcs_regs);
 
+	res = platform_get_resource(phy_pdev, IORESOURCE_MEM, phy_memnum++);
+	pdata->rxtx_regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(pdata->rxtx_regs)) {
+		dev_err(dev, "rxtx ioremap failed\n");
+		ret = PTR_ERR(pdata->rxtx_regs);
+		goto err_io;
+	}
+	if (netif_msg_probe(pdata))
+		dev_dbg(dev, "rxtx_regs  = %p\n", pdata->rxtx_regs);
+
+	res = platform_get_resource(phy_pdev, IORESOURCE_MEM, phy_memnum++);
+	pdata->sir0_regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(pdata->sir0_regs)) {
+		dev_err(dev, "sir0 ioremap failed\n");
+		ret = PTR_ERR(pdata->sir0_regs);
+		goto err_io;
+	}
+	if (netif_msg_probe(pdata))
+		dev_dbg(dev, "sir0_regs  = %p\n", pdata->sir0_regs);
+
+	res = platform_get_resource(phy_pdev, IORESOURCE_MEM, phy_memnum++);
+	pdata->sir1_regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(pdata->sir1_regs)) {
+		dev_err(dev, "sir1 ioremap failed\n");
+		ret = PTR_ERR(pdata->sir1_regs);
+		goto err_io;
+	}
+	if (netif_msg_probe(pdata))
+		dev_dbg(dev, "sir1_regs  = %p\n", pdata->sir1_regs);
+
 	/* Retrieve the MAC address */
 	ret = device_property_read_u8_array(dev, XGBE_MAC_ADDR_PROPERTY,
 					    pdata->mac_addr,
@@ -366,6 +510,115 @@ static int xgbe_probe(struct platform_device *pdev)
 	if (device_property_present(dev, XGBE_DMA_IRQS_PROPERTY))
 		pdata->per_channel_irq = 1;
 
+	/* Retrieve the PHY speedset */
+	ret = device_property_read_u32(phy_dev, XGBE_SPEEDSET_PROPERTY,
+				       &pdata->speed_set);
+	if (ret) {
+		dev_err(dev, "invalid %s property\n", XGBE_SPEEDSET_PROPERTY);
+		goto err_io;
+	}
+
+	switch (pdata->speed_set) {
+	case XGBE_SPEEDSET_1000_10000:
+	case XGBE_SPEEDSET_2500_10000:
+		break;
+	default:
+		dev_err(dev, "invalid %s property\n", XGBE_SPEEDSET_PROPERTY);
+		ret = -EINVAL;
+		goto err_io;
+	}
+
+	/* Retrieve the PHY configuration properties */
+	if (device_property_present(phy_dev, XGBE_BLWC_PROPERTY)) {
+		ret = device_property_read_u32_array(phy_dev,
+						     XGBE_BLWC_PROPERTY,
+						     pdata->serdes_blwc,
+						     XGBE_SPEEDS);
+		if (ret) {
+			dev_err(dev, "invalid %s property\n",
+				XGBE_BLWC_PROPERTY);
+			goto err_io;
+		}
+	} else {
+		memcpy(pdata->serdes_blwc, xgbe_serdes_blwc,
+		       sizeof(pdata->serdes_blwc));
+	}
+
+	if (device_property_present(phy_dev, XGBE_CDR_RATE_PROPERTY)) {
+		ret = device_property_read_u32_array(phy_dev,
+						     XGBE_CDR_RATE_PROPERTY,
+						     pdata->serdes_cdr_rate,
+						     XGBE_SPEEDS);
+		if (ret) {
+			dev_err(dev, "invalid %s property\n",
+				XGBE_CDR_RATE_PROPERTY);
+			goto err_io;
+		}
+	} else {
+		memcpy(pdata->serdes_cdr_rate, xgbe_serdes_cdr_rate,
+		       sizeof(pdata->serdes_cdr_rate));
+	}
+
+	if (device_property_present(phy_dev, XGBE_PQ_SKEW_PROPERTY)) {
+		ret = device_property_read_u32_array(phy_dev,
+						     XGBE_PQ_SKEW_PROPERTY,
+						     pdata->serdes_pq_skew,
+						     XGBE_SPEEDS);
+		if (ret) {
+			dev_err(dev, "invalid %s property\n",
+				XGBE_PQ_SKEW_PROPERTY);
+			goto err_io;
+		}
+	} else {
+		memcpy(pdata->serdes_pq_skew, xgbe_serdes_pq_skew,
+		       sizeof(pdata->serdes_pq_skew));
+	}
+
+	if (device_property_present(phy_dev, XGBE_TX_AMP_PROPERTY)) {
+		ret = device_property_read_u32_array(phy_dev,
+						     XGBE_TX_AMP_PROPERTY,
+						     pdata->serdes_tx_amp,
+						     XGBE_SPEEDS);
+		if (ret) {
+			dev_err(dev, "invalid %s property\n",
+				XGBE_TX_AMP_PROPERTY);
+			goto err_io;
+		}
+	} else {
+		memcpy(pdata->serdes_tx_amp, xgbe_serdes_tx_amp,
+		       sizeof(pdata->serdes_tx_amp));
+	}
+
+	if (device_property_present(phy_dev, XGBE_DFE_CFG_PROPERTY)) {
+		ret = device_property_read_u32_array(phy_dev,
+						     XGBE_DFE_CFG_PROPERTY,
+						     pdata->serdes_dfe_tap_cfg,
+						     XGBE_SPEEDS);
+		if (ret) {
+			dev_err(dev, "invalid %s property\n",
+				XGBE_DFE_CFG_PROPERTY);
+			goto err_io;
+		}
+	} else {
+		memcpy(pdata->serdes_dfe_tap_cfg, xgbe_serdes_dfe_tap_cfg,
+		       sizeof(pdata->serdes_dfe_tap_cfg));
+	}
+
+	if (device_property_present(phy_dev, XGBE_DFE_ENA_PROPERTY)) {
+		ret = device_property_read_u32_array(phy_dev,
+						     XGBE_DFE_ENA_PROPERTY,
+						     pdata->serdes_dfe_tap_ena,
+						     XGBE_SPEEDS);
+		if (ret) {
+			dev_err(dev, "invalid %s property\n",
+				XGBE_DFE_ENA_PROPERTY);
+			goto err_io;
+		}
+	} else {
+		memcpy(pdata->serdes_dfe_tap_ena, xgbe_serdes_dfe_tap_ena,
+		       sizeof(pdata->serdes_dfe_tap_ena));
+	}
+
 	/* Obtain device settings unique to ACPI/OF */
 	if (pdata->use_acpi)
 		ret = xgbe_acpi_support(pdata);
@@ -393,17 +646,23 @@ static int xgbe_probe(struct platform_device *pdev)
 	}
 	pdata->dev_irq = ret;
 
+	/* Get the auto-negotiation interrupt */
+	ret = platform_get_irq(phy_pdev, phy_irqnum++);
+	if (ret < 0) {
+		dev_err(dev, "platform_get_irq phy 0 failed\n");
+		goto err_io;
+	}
+	pdata->an_irq = ret;
+
 	netdev->irq = pdata->dev_irq;
 	netdev->base_addr = (unsigned long)pdata->xgmac_regs;
 	memcpy(netdev->dev_addr, pdata->mac_addr, netdev->addr_len);
 
 	/* Set all the function pointers */
 	xgbe_init_all_fptrs(pdata);
-	hw_if = &pdata->hw_if;
-	desc_if = &pdata->desc_if;
 
 	/* Issue software reset to device */
-	hw_if->exit(pdata);
+	pdata->hw_if.exit(pdata);
 
 	/* Populate the hardware features */
 	xgbe_get_all_hw_features(pdata);
@@ -458,16 +717,8 @@ static int xgbe_probe(struct platform_device *pdev)
 	XGMAC_SET_BITS(pdata->rss_options, MAC_RSSCR, TCP4TE, 1);
 	XGMAC_SET_BITS(pdata->rss_options, MAC_RSSCR, UDP4TE, 1);
 
-	/* Prepare to regsiter with MDIO */
-	pdata->mii_bus_id = kasprintf(GFP_KERNEL, "%s", pdev->name);
-	if (!pdata->mii_bus_id) {
-		dev_err(dev, "failed to allocate mii bus id\n");
-		ret = -ENOMEM;
-		goto err_io;
-	}
-	ret = xgbe_mdio_register(pdata);
-	if (ret)
-		goto err_bus_id;
+	/* Call MDIO/PHY initialization routine */
+	pdata->phy_if.phy_init(pdata);
 
 	/* Set device operations */
 	netdev->netdev_ops = xgbe_get_netdev_ops();
@@ -512,26 +763,52 @@ static int xgbe_probe(struct platform_device *pdev)
 	ret = register_netdev(netdev);
 	if (ret) {
 		dev_err(dev, "net device registration failed\n");
-		goto err_reg_netdev;
+		goto err_io;
+	}
+
+	/* Create the PHY/ANEG name based on netdev name */
+	snprintf(pdata->an_name, sizeof(pdata->an_name) - 1, "%s-pcs",
+		 netdev_name(netdev));
+
+	/* Create workqueues */
+	pdata->dev_workqueue =
+		create_singlethread_workqueue(netdev_name(netdev));
+	if (!pdata->dev_workqueue) {
+		netdev_err(netdev, "device workqueue creation failed\n");
+		ret = -ENOMEM;
+		goto err_netdev;
+	}
+
+	pdata->an_workqueue =
+		create_singlethread_workqueue(pdata->an_name);
+	if (!pdata->an_workqueue) {
+		netdev_err(netdev, "phy workqueue creation failed\n");
+		ret = -ENOMEM;
+		goto err_wq;
 	}
 
 	xgbe_ptp_register(pdata);
 
 	xgbe_debugfs_init(pdata);
 
+	platform_device_put(phy_pdev);
+
 	netdev_notice(netdev, "net device enabled\n");
 
 	DBGPR("<-- xgbe_probe\n");
 
 	return 0;
 
-err_reg_netdev:
-	xgbe_mdio_unregister(pdata);
+err_wq:
+	destroy_workqueue(pdata->dev_workqueue);
 
-err_bus_id:
-	kfree(pdata->mii_bus_id);
+err_netdev:
+	unregister_netdev(netdev);
 
 err_io:
+	platform_device_put(phy_pdev);
+
+err_phydev:
 	free_netdev(netdev);
 
 err_alloc:
@@ -551,11 +828,13 @@ static int xgbe_remove(struct platform_device *pdev)
 
 	xgbe_ptp_unregister(pdata);
 
-	unregister_netdev(netdev);
+	flush_workqueue(pdata->an_workqueue);
+	destroy_workqueue(pdata->an_workqueue);
 
-	xgbe_mdio_unregister(pdata);
+	flush_workqueue(pdata->dev_workqueue);
+	destroy_workqueue(pdata->dev_workqueue);
 
-	kfree(pdata->mii_bus_id);
+	unregister_netdev(netdev);
 
 	free_netdev(netdev);
 
@@ -568,16 +847,17 @@ static int xgbe_remove(struct platform_device *pdev)
 static int xgbe_suspend(struct device *dev)
 {
 	struct net_device *netdev = dev_get_drvdata(dev);
-	int ret;
+	struct xgbe_prv_data *pdata = netdev_priv(netdev);
+	int ret = 0;
 
 	DBGPR("-->xgbe_suspend\n");
 
-	if (!netif_running(netdev)) {
-		DBGPR("<--xgbe_dev_suspend\n");
-		return -EINVAL;
-	}
+	if (netif_running(netdev))
+		ret = xgbe_powerdown(netdev, XGMAC_DRIVER_CONTEXT);
 
-	ret = xgbe_powerdown(netdev, XGMAC_DRIVER_CONTEXT);
+	pdata->lpm_ctrl = XMDIO_READ(pdata, MDIO_MMD_PCS, MDIO_CTRL1);
+	pdata->lpm_ctrl |= MDIO_CTRL1_LPOWER;
+	XMDIO_WRITE(pdata, MDIO_MMD_PCS, MDIO_CTRL1, pdata->lpm_ctrl);
 
 	DBGPR("<--xgbe_suspend\n");
 
@@ -587,16 +867,16 @@ static int xgbe_suspend(struct device *dev)
 static int xgbe_resume(struct device *dev)
 {
 	struct net_device *netdev = dev_get_drvdata(dev);
-	int ret;
+	struct xgbe_prv_data *pdata = netdev_priv(netdev);
+	int ret = 0;
 
 	DBGPR("-->xgbe_resume\n");
 
-	if (!netif_running(netdev)) {
-		DBGPR("<--xgbe_dev_resume\n");
-		return -EINVAL;
-	}
+	pdata->lpm_ctrl &= ~MDIO_CTRL1_LPOWER;
+	XMDIO_WRITE(pdata, MDIO_MMD_PCS, MDIO_CTRL1, pdata->lpm_ctrl);
 
-	ret = xgbe_powerup(netdev, XGMAC_DRIVER_CONTEXT);
+	if (netif_running(netdev))
+		ret = xgbe_powerup(netdev, XGMAC_DRIVER_CONTEXT);
 
 	DBGPR("<--xgbe_resume\n");
 

drivers/net/ethernet/amd/xgbe/xgbe.h

@@ -129,7 +129,7 @@
 #include <net/dcbnl.h>
 
 #define XGBE_DRV_NAME		"amd-xgbe"
-#define XGBE_DRV_VERSION	"1.0.0-a"
+#define XGBE_DRV_VERSION	"1.0.1"
 #define XGBE_DRV_DESC		"AMD 10 Gigabit Ethernet Driver"
 
 /* Descriptor related defines */
@@ -178,14 +178,17 @@
 #define XGMAC_JUMBO_PACKET_MTU	9000
 #define XGMAC_MAX_JUMBO_PACKET	9018
 
-/* MDIO bus phy name */
-#define XGBE_PHY_NAME		"amd_xgbe_phy"
-#define XGBE_PRTAD		0
-
 /* Common property names */
 #define XGBE_MAC_ADDR_PROPERTY	"mac-address"
 #define XGBE_PHY_MODE_PROPERTY	"phy-mode"
 #define XGBE_DMA_IRQS_PROPERTY	"amd,per-channel-interrupt"
+#define XGBE_SPEEDSET_PROPERTY	"amd,speed-set"
+#define XGBE_BLWC_PROPERTY	"amd,serdes-blwc"
+#define XGBE_CDR_RATE_PROPERTY	"amd,serdes-cdr-rate"
+#define XGBE_PQ_SKEW_PROPERTY	"amd,serdes-pq-skew"
+#define XGBE_TX_AMP_PROPERTY	"amd,serdes-tx-amp"
+#define XGBE_DFE_CFG_PROPERTY	"amd,serdes-dfe-tap-config"
+#define XGBE_DFE_ENA_PROPERTY	"amd,serdes-dfe-tap-enable"
 
 /* Device-tree clock names */
 #define XGBE_DMA_CLOCK		"dma_clk"
@@ -241,6 +244,49 @@
 #define XGBE_RSS_LOOKUP_TABLE_TYPE	0
 #define XGBE_RSS_HASH_KEY_TYPE		1
 
+/* Auto-negotiation */
+#define XGBE_AN_MS_TIMEOUT		500
+#define XGBE_LINK_TIMEOUT		10
+
+#define XGBE_AN_INT_CMPLT		0x01
+#define XGBE_AN_INC_LINK		0x02
+#define XGBE_AN_PG_RCV			0x04
+#define XGBE_AN_INT_MASK		0x07
+
+/* Rate-change complete wait/retry count */
+#define XGBE_RATECHANGE_COUNT		500
+
+/* Default SerDes settings */
+#define XGBE_SPEED_10000_BLWC		0
+#define XGBE_SPEED_10000_CDR		0x7
+#define XGBE_SPEED_10000_PLL		0x1
+#define XGBE_SPEED_10000_PQ		0x12
+#define XGBE_SPEED_10000_RATE		0x0
+#define XGBE_SPEED_10000_TXAMP		0xa
+#define XGBE_SPEED_10000_WORD		0x7
+#define XGBE_SPEED_10000_DFE_TAP_CONFIG	0x1
+#define XGBE_SPEED_10000_DFE_TAP_ENABLE	0x7f
+
+#define XGBE_SPEED_2500_BLWC		1
+#define XGBE_SPEED_2500_CDR		0x2
+#define XGBE_SPEED_2500_PLL		0x0
+#define XGBE_SPEED_2500_PQ		0xa
+#define XGBE_SPEED_2500_RATE		0x1
+#define XGBE_SPEED_2500_TXAMP		0xf
+#define XGBE_SPEED_2500_WORD		0x1
+#define XGBE_SPEED_2500_DFE_TAP_CONFIG	0x3
+#define XGBE_SPEED_2500_DFE_TAP_ENABLE	0x0
+
+#define XGBE_SPEED_1000_BLWC		1
+#define XGBE_SPEED_1000_CDR		0x2
+#define XGBE_SPEED_1000_PLL		0x0
+#define XGBE_SPEED_1000_PQ		0xa
+#define XGBE_SPEED_1000_RATE		0x3
+#define XGBE_SPEED_1000_TXAMP		0xf
+#define XGBE_SPEED_1000_WORD		0x1
+#define XGBE_SPEED_1000_DFE_TAP_CONFIG	0x3
+#define XGBE_SPEED_1000_DFE_TAP_ENABLE	0x0
+
 struct xgbe_prv_data;
 
 struct xgbe_packet_data {
@@ -412,6 +458,13 @@ struct xgbe_channel {
 	struct xgbe_ring *rx_ring;
 } ____cacheline_aligned;
 
+enum xgbe_state {
+	XGBE_DOWN,
+	XGBE_LINK,
+	XGBE_LINK_INIT,
+	XGBE_LINK_ERR,
+};
+
 enum xgbe_int {
 	XGMAC_INT_DMA_CH_SR_TI,
 	XGMAC_INT_DMA_CH_SR_TPS,
@@ -443,6 +496,55 @@ enum xgbe_mtl_fifo_size {
 	XGMAC_MTL_FIFO_SIZE_256K = 0x3ff,
 };
 
+enum xgbe_speed {
+	XGBE_SPEED_1000 = 0,
+	XGBE_SPEED_2500,
+	XGBE_SPEED_10000,
+	XGBE_SPEEDS,
+};
+
+enum xgbe_an {
+	XGBE_AN_READY = 0,
+	XGBE_AN_PAGE_RECEIVED,
+	XGBE_AN_INCOMPAT_LINK,
+	XGBE_AN_COMPLETE,
+	XGBE_AN_NO_LINK,
+	XGBE_AN_ERROR,
+};
+
+enum xgbe_rx {
+	XGBE_RX_BPA = 0,
+	XGBE_RX_XNP,
+	XGBE_RX_COMPLETE,
+	XGBE_RX_ERROR,
+};
+
+enum xgbe_mode {
+	XGBE_MODE_KR = 0,
+	XGBE_MODE_KX,
+};
+
+enum xgbe_speedset {
+	XGBE_SPEEDSET_1000_10000 = 0,
+	XGBE_SPEEDSET_2500_10000,
+};
+
+struct xgbe_phy {
+	u32 supported;
+	u32 advertising;
+	u32 lp_advertising;
+
+	int address;
+
+	int autoneg;
+	int speed;
+	int duplex;
+	int pause;
+	int asym_pause;
+
+	int link;
+};
+
 struct xgbe_mmc_stats {
 	/* Tx Stats */
 	u64 txoctetcount_gb;
@@ -594,6 +696,20 @@ struct xgbe_hw_if {
 	int (*set_rss_lookup_table)(struct xgbe_prv_data *, const u32 *);
 };
 
+struct xgbe_phy_if {
+	/* For initial PHY setup */
+	void (*phy_init)(struct xgbe_prv_data *);
+
+	/* For PHY support when setting device up/down */
+	int (*phy_reset)(struct xgbe_prv_data *);
+	int (*phy_start)(struct xgbe_prv_data *);
+	void (*phy_stop)(struct xgbe_prv_data *);
+
+	/* For PHY support while device is up */
+	void (*phy_status)(struct xgbe_prv_data *);
+	int (*phy_config_aneg)(struct xgbe_prv_data *);
+};
+
 struct xgbe_desc_if {
 	int (*alloc_ring_resources)(struct xgbe_prv_data *);
 	void (*free_ring_resources)(struct xgbe_prv_data *);
@@ -663,6 +779,9 @@ struct xgbe_prv_data {
 	/* XGMAC/XPCS related mmio registers */
 	void __iomem *xgmac_regs;	/* XGMAC CSRs */
 	void __iomem *xpcs_regs;	/* XPCS MMD registers */
+	void __iomem *rxtx_regs;	/* SerDes Rx/Tx CSRs */
+	void __iomem *sir0_regs;	/* SerDes integration registers (1/2) */
+	void __iomem *sir1_regs;	/* SerDes integration registers (2/2) */
 
 	/* Overall device lock */
 	spinlock_t lock;
@@ -673,10 +792,14 @@ struct xgbe_prv_data {
 	/* RSS addressing mutex */
 	struct mutex rss_mutex;
 
+	/* Flags representing xgbe_state */
+	unsigned long dev_state;
+
 	int dev_irq;
 	unsigned int per_channel_irq;
 
 	struct xgbe_hw_if hw_if;
+	struct xgbe_phy_if phy_if;
 	struct xgbe_desc_if desc_if;
 
 	/* AXI DMA settings */
@@ -685,6 +808,11 @@ struct xgbe_prv_data {
 	unsigned int arcache;
 	unsigned int awcache;
 
+	/* Service routine support */
+	struct workqueue_struct *dev_workqueue;
+	struct work_struct service_work;
+	struct timer_list service_timer;
+
 	/* Rings for Tx/Rx on a DMA channel */
 	struct xgbe_channel *channel;
 	unsigned int channel_count;
@@ -732,22 +860,6 @@ struct xgbe_prv_data {
 	u32 rss_table[XGBE_RSS_MAX_TABLE_SIZE];
 	u32 rss_options;
 
-	/* MDIO settings */
-	struct module *phy_module;
-	char *mii_bus_id;
-	struct mii_bus *mii;
-	int mdio_mmd;
-	struct phy_device *phydev;
-	int default_autoneg;
-	int default_speed;
-
-	/* Current PHY settings */
-	phy_interface_t phy_mode;
-	int phy_link;
-	int phy_speed;
-	unsigned int phy_tx_pause;
-	unsigned int phy_rx_pause;
-
 	/* Netdev related settings */
 	unsigned char mac_addr[ETH_ALEN];
 	netdev_features_t netdev_features;
@@ -794,6 +906,53 @@ struct xgbe_prv_data {
 	/* Network interface message level setting */
 	u32 msg_enable;
 
+	/* Current PHY settings */
+	phy_interface_t phy_mode;
+	int phy_link;
+	int phy_speed;
+	unsigned int phy_tx_pause;
+	unsigned int phy_rx_pause;
+
+	/* MDIO/PHY related settings */
+	struct xgbe_phy phy;
+	int mdio_mmd;
+	unsigned long link_check;
+
+	char an_name[IFNAMSIZ + 32];
+	struct workqueue_struct *an_workqueue;
+
+	int an_irq;
+	struct work_struct an_irq_work;
+
+	unsigned int speed_set;
+
+	/* SerDes UEFI configurable settings.
+	 *   Switching between modes/speeds requires new values for some
+	 *   SerDes settings.  The values can be supplied as device
+	 *   properties in array format.  The first array entry is for
+	 *   1GbE, second for 2.5GbE and third for 10GbE
+	 */
+	u32 serdes_blwc[XGBE_SPEEDS];
+	u32 serdes_cdr_rate[XGBE_SPEEDS];
+	u32 serdes_pq_skew[XGBE_SPEEDS];
+	u32 serdes_tx_amp[XGBE_SPEEDS];
+	u32 serdes_dfe_tap_cfg[XGBE_SPEEDS];
+	u32 serdes_dfe_tap_ena[XGBE_SPEEDS];
+
+	/* Auto-negotiation state machine support */
+	struct mutex an_mutex;
+	enum xgbe_an an_result;
+	enum xgbe_an an_state;
+	enum xgbe_rx kr_state;
+	enum xgbe_rx kx_state;
+	struct work_struct an_work;
+	unsigned int an_supported;
+	unsigned int parallel_detect;
+	unsigned int fec_ability;
+	unsigned long an_start;
+
+	unsigned int lpm_ctrl;		/* CTRL1 for resume */
+
 #ifdef CONFIG_DEBUG_FS
 	struct dentry *xgbe_debugfs;
 
@@ -807,6 +966,7 @@ struct xgbe_prv_data {
 /* Function prototypes*/
 
 void xgbe_init_function_ptrs_dev(struct xgbe_hw_if *);
+void xgbe_init_function_ptrs_phy(struct xgbe_phy_if *);
 void xgbe_init_function_ptrs_desc(struct xgbe_desc_if *);
 struct net_device_ops *xgbe_get_netdev_ops(void);
 struct ethtool_ops *xgbe_get_ethtool_ops(void);
@@ -814,9 +974,6 @@ struct ethtool_ops *xgbe_get_ethtool_ops(void);
 const struct dcbnl_rtnl_ops *xgbe_get_dcbnl_ops(void);
 #endif
 
-int xgbe_mdio_register(struct xgbe_prv_data *);
-void xgbe_mdio_unregister(struct xgbe_prv_data *);
-void xgbe_dump_phy_registers(struct xgbe_prv_data *);
 void xgbe_ptp_register(struct xgbe_prv_data *);
 void xgbe_ptp_unregister(struct xgbe_prv_data *);
 void xgbe_dump_tx_desc(struct xgbe_prv_data *, struct xgbe_ring *,

drivers/net/phy/Kconfig

@@ -24,13 +24,6 @@ config AMD_PHY
 	---help---
 	  Currently supports the am79c874
 
-config AMD_XGBE_PHY
-	tristate "Driver for the AMD 10GbE (amd-xgbe) PHYs"
-	depends on (OF || ACPI) && HAS_IOMEM
-	depends on ARM64 || COMPILE_TEST
-	---help---
-	  Currently supports the AMD 10GbE PHY
-
 config MARVELL_PHY
 	tristate "Drivers for Marvell PHYs"
 	---help---

drivers/net/phy/Makefile

@@ -33,5 +33,4 @@ obj-$(CONFIG_MDIO_BUS_MUX_GPIO)	+= mdio-mux-gpio.o
 obj-$(CONFIG_MDIO_BUS_MUX_MMIOREG) += mdio-mux-mmioreg.o
 obj-$(CONFIG_MDIO_SUN4I)	+= mdio-sun4i.o
 obj-$(CONFIG_MDIO_MOXART)	+= mdio-moxart.o
-obj-$(CONFIG_AMD_XGBE_PHY)	+= amd-xgbe-phy.o
 obj-$(CONFIG_MDIO_BCM_UNIMAC)	+= mdio-bcm-unimac.o