Skip to content

K
kernel_linux

OpenHarmony / kernel_linux
上一次同步 3 年多

通知 13
Star 8
Fork 2
K
kernel_linux
提交 6ed83942 编写于 作者: G Graf Yang 提交者： Bryan Wu
浏览文件
操作

[Blackfin] arch: Resolve the clash issue of UART defines between blackfin... 

[Blackfin] arch: Resolve the clash issue of UART defines between blackfin headers and include/linux/serial_reg.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Cc: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
上级 db68254f
隐藏空白更改
内联 并排
Showing with 89 addition and 80 deletion
arch/blackfin/kernel/bfin_gpio.c
浏览文件 @ 6ed83942
......@@ -95,14 +95,14 @@ enum {
AWA_data_clear = SYSCR,
AWA_data_set = SYSCR,
AWA_toggle = SYSCR,
AWA_maska = UART_SCR,
AWA_maska_clear = UART_SCR,
AWA_maska_set = UART_SCR,
AWA_maska_toggle = UART_SCR,
AWA_maskb = UART_GCTL,
AWA_maskb_clear = UART_GCTL,
AWA_maskb_set = UART_GCTL,
AWA_maskb_toggle = UART_GCTL,
AWA_maska = BFIN_UART_SCR,
AWA_maska_clear = BFIN_UART_SCR,
AWA_maska_set = BFIN_UART_SCR,
AWA_maska_toggle = BFIN_UART_SCR,
AWA_maskb = BFIN_UART_GCTL,
AWA_maskb_clear = BFIN_UART_GCTL,
AWA_maskb_set = BFIN_UART_GCTL,
AWA_maskb_toggle = BFIN_UART_GCTL,
AWA_dir = SPORT1_STAT,
AWA_polar = SPORT1_STAT,
AWA_edge = SPORT1_STAT,
......
arch/blackfin/mach-bf533/head.S
浏览文件 @ 6ed83942
......@@ -151,26 +151,26 @@ ENTRY(__start)
/* Initialise UART - when booting from u-boot, the UART is not disabled
* so if we dont initalize here, our serial console gets hosed */
p0.h = hi(UART_LCR);
p0.l = lo(UART_LCR);
p0.h = hi(BFIN_UART_LCR);
p0.l = lo(BFIN_UART_LCR);
r0 = 0x0(Z);
w[p0] = r0.L; /* To enable DLL writes */
ssync;
p0.h = hi(UART_DLL);
p0.l = lo(UART_DLL);
p0.h = hi(BFIN_UART_DLL);
p0.l = lo(BFIN_UART_DLL);
r0 = 0x0(Z);
w[p0] = r0.L;
ssync;
p0.h = hi(UART_DLH);
p0.l = lo(UART_DLH);
p0.h = hi(BFIN_UART_DLH);
p0.l = lo(BFIN_UART_DLH);
r0 = 0x00(Z);
w[p0] = r0.L;
ssync;
p0.h = hi(UART_GCTL);
p0.l = lo(UART_GCTL);
p0.h = hi(BFIN_UART_GCTL);
p0.l = lo(BFIN_UART_GCTL);
r0 = 0x0(Z);
w[p0] = r0.L; /* To enable UART clock */
ssync;
......
arch/blackfin/mach-bf537/head.S
浏览文件 @ 6ed83942
......@@ -182,26 +182,26 @@ ENTRY(__start)
/* Initialise UART - when booting from u-boot, the UART is not disabled
* so if we dont initalize here, our serial console gets hosed */
p0.h = hi(UART_LCR);
p0.l = lo(UART_LCR);
p0.h = hi(BFIN_UART_LCR);
p0.l = lo(BFIN_UART_LCR);
r0 = 0x0(Z);
w[p0] = r0.L; /* To enable DLL writes */
ssync;
p0.h = hi(UART_DLL);
p0.l = lo(UART_DLL);
p0.h = hi(BFIN_UART_DLL);
p0.l = lo(BFIN_UART_DLL);
r0 = 0x0(Z);
w[p0] = r0.L;
ssync;
p0.h = hi(UART_DLH);
p0.l = lo(UART_DLH);
p0.h = hi(BFIN_UART_DLH);
p0.l = lo(BFIN_UART_DLH);
r0 = 0x00(Z);
w[p0] = r0.L;
ssync;
p0.h = hi(UART_GCTL);
p0.l = lo(UART_GCTL);
p0.h = hi(BFIN_UART_GCTL);
p0.l = lo(BFIN_UART_GCTL);
r0 = 0x0(Z);
w[p0] = r0.L; /* To enable UART clock */
ssync;
......
arch/blackfin/mach-bf561/head.S
浏览文件 @ 6ed83942
......@@ -139,26 +139,26 @@ ENTRY(__start)
/* Initialise UART - when booting from u-boot, the UART is not disabled
* so if we dont initalize here, our serial console gets hosed */
p0.h = hi(UART_LCR);
p0.l = lo(UART_LCR);
p0.h = hi(BFIN_UART_LCR);
p0.l = lo(BFIN_UART_LCR);
r0 = 0x0(Z);
w[p0] = r0.L; /* To enable DLL writes */
ssync;
p0.h = hi(UART_DLL);
p0.l = lo(UART_DLL);
p0.h = hi(BFIN_UART_DLL);
p0.l = lo(BFIN_UART_DLL);
r0 = 0x0(Z);
w[p0] = r0.L;
ssync;
p0.h = hi(UART_DLH);
p0.l = lo(UART_DLH);
p0.h = hi(BFIN_UART_DLH);
p0.l = lo(BFIN_UART_DLH);
r0 = 0x00(Z);
w[p0] = r0.L;
ssync;
p0.h = hi(UART_GCTL);
p0.l = lo(UART_GCTL);
p0.h = hi(BFIN_UART_GCTL);
p0.l = lo(BFIN_UART_GCTL);
r0 = 0x0(Z);
w[p0] = r0.L; /* To enable UART clock */
ssync;
......
include/asm-blackfin/mach-bf533/defBF532.h
浏览文件 @ 6ed83942
......@@ -88,20 +88,25 @@
#define RTC_PREN 0xFFC00314 /* RTC Prescaler Enable Register (alternate macro) */
/* UART Controller (0xFFC00400 - 0xFFC004FF) */
#define UART_THR 0xFFC00400 /* Transmit Holding register */
#define UART_RBR 0xFFC00400 /* Receive Buffer register */
#define UART_DLL 0xFFC00400 /* Divisor Latch (Low-Byte) */
#define UART_IER 0xFFC00404 /* Interrupt Enable Register */
#define UART_DLH 0xFFC00404 /* Divisor Latch (High-Byte) */
#define UART_IIR 0xFFC00408 /* Interrupt Identification Register */
#define UART_LCR 0xFFC0040C /* Line Control Register */
#define UART_MCR 0xFFC00410 /* Modem Control Register */
#define UART_LSR 0xFFC00414 /* Line Status Register */
/*
* Because include/linux/serial_reg.h have defined UART_*,
* So we define blackfin uart regs to BFIN_UART_*.
*/
#define BFIN_UART_THR 0xFFC00400 /* Transmit Holding register */
#define BFIN_UART_RBR 0xFFC00400 /* Receive Buffer register */
#define BFIN_UART_DLL 0xFFC00400 /* Divisor Latch (Low-Byte) */
#define BFIN_UART_IER 0xFFC00404 /* Interrupt Enable Register */
#define BFIN_UART_DLH 0xFFC00404 /* Divisor Latch (High-Byte) */
#define BFIN_UART_IIR 0xFFC00408 /* Interrupt Identification Register */
#define BFIN_UART_LCR 0xFFC0040C /* Line Control Register */
#define BFIN_UART_MCR 0xFFC00410 /* Modem Control Register */
#define BFIN_UART_LSR 0xFFC00414 /* Line Status Register */
#if 0
#define UART_MSR 0xFFC00418 /* Modem Status Register (UNUSED in ADSP-BF532) */
#define BFIN_UART_MSR 0xFFC00418 /* Modem Status Register (UNUSED in ADSP-BF532) */
#endif
#define UART_SCR 0xFFC0041C /* SCR Scratch Register */
#define UART_GCTL 0xFFC00424 /* Global Control Register */
#define BFIN_UART_SCR 0xFFC0041C /* SCR Scratch Register */
#define BFIN_UART_GCTL 0xFFC00424 /* Global Control Register */
/* SPI Controller (0xFFC00500 - 0xFFC005FF) */
#define SPI0_REGBASE 0xFFC00500
......
include/asm-blackfin/mach-bf537/blackfin.h
浏览文件 @ 6ed83942
......@@ -82,8 +82,6 @@
#define STATUS_P1 0x02
#define STATUS_P0 0x01
/* UART 0*/
/* DMA Channnel */
#define bfin_read_CH_UART_RX() bfin_read_CH_UART0_RX()
#define bfin_write_CH_UART_RX(val) bfin_write_CH_UART0_RX(val)
......@@ -106,37 +104,37 @@
/* MMR Registers*/
#define bfin_read_UART_THR() bfin_read_UART0_THR()
#define bfin_write_UART_THR(val) bfin_write_UART0_THR(val)
#define UART_THR UART0_THR
#define BFIN_UART_THR UART0_THR
#define bfin_read_UART_RBR() bfin_read_UART0_RBR()
#define bfin_write_UART_RBR(val) bfin_write_UART0_RBR(val)
#define UART_RBR UART0_RBR
#define BFIN_UART_RBR UART0_RBR
#define bfin_read_UART_DLL() bfin_read_UART0_DLL()
#define bfin_write_UART_DLL(val) bfin_write_UART0_DLL(val)
#define UART_DLL UART0_DLL
#define BFIN_UART_DLL UART0_DLL
#define bfin_read_UART_IER() bfin_read_UART0_IER()
#define bfin_write_UART_IER(val) bfin_write_UART0_IER(val)
#define UART_IER UART0_IER
#define BFIN_UART_IER UART0_IER
#define bfin_read_UART_DLH() bfin_read_UART0_DLH()
#define bfin_write_UART_DLH(val) bfin_write_UART0_DLH(val)
#define UART_DLH UART0_DLH
#define BFIN_UART_DLH UART0_DLH
#define bfin_read_UART_IIR() bfin_read_UART0_IIR()
#define bfin_write_UART_IIR(val) bfin_write_UART0_IIR(val)
#define UART_IIR UART0_IIR
#define BFIN_UART_IIR UART0_IIR
#define bfin_read_UART_LCR() bfin_read_UART0_LCR()
#define bfin_write_UART_LCR(val) bfin_write_UART0_LCR(val)
#define UART_LCR UART0_LCR
#define BFIN_UART_LCR UART0_LCR
#define bfin_read_UART_MCR() bfin_read_UART0_MCR()
#define bfin_write_UART_MCR(val) bfin_write_UART0_MCR(val)
#define UART_MCR UART0_MCR
#define BFIN_UART_MCR UART0_MCR
#define bfin_read_UART_LSR() bfin_read_UART0_LSR()
#define bfin_write_UART_LSR(val) bfin_write_UART0_LSR(val)
#define UART_LSR UART0_LSR
#define BFIN_UART_LSR UART0_LSR
#define bfin_read_UART_SCR() bfin_read_UART0_SCR()
#define bfin_write_UART_SCR(val) bfin_write_UART0_SCR(val)
#define UART_SCR UART0_SCR
#define BFIN_UART_SCR UART0_SCR
#define bfin_read_UART_GCTL() bfin_read_UART0_GCTL()
#define bfin_write_UART_GCTL(val) bfin_write_UART0_GCTL(val)
#define UART_GCTL UART0_GCTL
#define BFIN_UART_GCTL UART0_GCTL
/* DPMC*/
#define bfin_read_STOPCK_OFF() bfin_read_STOPCK()
......
include/asm-blackfin/mach-bf548/blackfin.h
浏览文件 @ 6ed83942
......@@ -153,17 +153,18 @@
#define bfin_write_UART_SCR(val) bfin_write_UART1_SCR(val)
#define bfin_read_UART_GCTL() bfin_read_UART1_GCTL()
#define bfin_write_UART_GCTL(val) bfin_write_UART1_GCTL(val)
#define UART_THR UART1_THR
#define UART_RBR UART1_RBR
#define UART_DLL UART1_DLL
#define UART_IER UART1_IER
#define UART_DLH UART1_DLH
#define UART_IIR UART1_IIR
#define UART_LCR UART1_LCR
#define UART_MCR UART1_MCR
#define UART_LSR UART1_LSR
#define UART_SCR UART1_SCR
#define UART_GCTL UART1_GCTL
#define BFIN_UART_THR UART1_THR
#define BFIN_UART_RBR UART1_RBR
#define BFIN_UART_DLL UART1_DLL
#define BFIN_UART_IER UART1_IER
#define BFIN_UART_DLH UART1_DLH
#define BFIN_UART_IIR UART1_IIR
#define BFIN_UART_LCR UART1_LCR
#define BFIN_UART_MCR UART1_MCR
#define BFIN_UART_LSR UART1_LSR
#define BFIN_UART_SCR UART1_SCR
#define BFIN_UART_GCTL UART1_GCTL
/* PLL_DIV Masks */
#define CCLK_DIV1 CSEL_DIV1 /* CCLK = VCO / 1 */
......
include/asm-blackfin/mach-bf561/defBF561.h
浏览文件 @ 6ed83942
......@@ -110,18 +110,23 @@
#define WDOGB_STAT 0xFFC01208 /* Watchdog Status register */
/* UART Controller (0xFFC00400 - 0xFFC004FF) */
#define UART_THR 0xFFC00400 /* Transmit Holding register */
#define UART_RBR 0xFFC00400 /* Receive Buffer register */
#define UART_DLL 0xFFC00400 /* Divisor Latch (Low-Byte) */
#define UART_IER 0xFFC00404 /* Interrupt Enable Register */
#define UART_DLH 0xFFC00404 /* Divisor Latch (High-Byte) */
#define UART_IIR 0xFFC00408 /* Interrupt Identification Register */
#define UART_LCR 0xFFC0040C /* Line Control Register */
#define UART_MCR 0xFFC00410 /* Modem Control Register */
#define UART_LSR 0xFFC00414 /* Line Status Register */
#define UART_MSR 0xFFC00418 /* Modem Status Register */
#define UART_SCR 0xFFC0041C /* SCR Scratch Register */
#define UART_GCTL 0xFFC00424 /* Global Control Register */
/*
* Because include/linux/serial_reg.h have defined UART_*,
* So we define blackfin uart regs to BFIN_UART0_*.
*/
#define BFIN_UART_THR 0xFFC00400 /* Transmit Holding register */
#define BFIN_UART_RBR 0xFFC00400 /* Receive Buffer register */
#define BFIN_UART_DLL 0xFFC00400 /* Divisor Latch (Low-Byte) */
#define BFIN_UART_IER 0xFFC00404 /* Interrupt Enable Register */
#define BFIN_UART_DLH 0xFFC00404 /* Divisor Latch (High-Byte) */
#define BFIN_UART_IIR 0xFFC00408 /* Interrupt Identification Register */
#define BFIN_UART_LCR 0xFFC0040C /* Line Control Register */
#define BFIN_UART_MCR 0xFFC00410 /* Modem Control Register */
#define BFIN_UART_LSR 0xFFC00414 /* Line Status Register */
#define BFIN_UART_MSR 0xFFC00418 /* Modem Status Register */
#define BFIN_UART_SCR 0xFFC0041C /* SCR Scratch Register */
#define BFIN_UART_GCTL 0xFFC00424 /* Global Control Register */
/* SPI Controller (0xFFC00500 - 0xFFC005FF) */
#define SPI0_REGBASE 0xFFC00500
......
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或