Skip to content

K
kernel_linux

OpenHarmony / kernel_linux
上一次同步 4 年多

通知 15
Star 8
Fork 2
K
kernel_linux
提交 67b738ef 编写于 作者: T Tony Lindgren
浏览文件
操作

Merge branch 'devel-omap-irq' into omap-for-linus

上级 c451278c 5d190c40
展开全部 隐藏空白更改
内联 并排
Showing with 3739 addition and 3472 deletion
Documentation/ABI/testing/sysfs-bus-rbd 0 → 100644
浏览文件 @ 67b738ef
What: /sys/bus/rbd/
Date: November 2010
Contact: Yehuda Sadeh <yehuda@hq.newdream.net>,
Sage Weil <sage@newdream.net>
Description:
Being used for adding and removing rbd block devices.
Usage: <mon ip addr> <options> <pool name> <rbd image name> [snap name]
$ echo "192.168.0.1 name=admin rbd foo" > /sys/bus/rbd/add
The snapshot name can be "-" or omitted to map the image read/write. A <dev-id>
will be assigned for any registered block device. If snapshot is used, it will
be mapped read-only.
Removal of a device:
$ echo <dev-id> > /sys/bus/rbd/remove
Entries under /sys/bus/rbd/devices/<dev-id>/
--------------------------------------------
client_id
The ceph unique client id that was assigned for this specific session.
major
The block device major number.
name
The name of the rbd image.
pool
The pool where this rbd image resides. The pool-name pair is unique
per rados system.
size
The size (in bytes) of the mapped block device.
refresh
Writing to this file will reread the image header data and set
all relevant datastructures accordingly.
current_snap
The current snapshot for which the device is mapped.
create_snap
Create a snapshot:
$ echo <snap-name> > /sys/bus/rbd/devices/<dev-id>/snap_create
rollback_snap
Rolls back data to the specified snapshot. This goes over the entire
list of rados blocks and sends a rollback command to each.
$ echo <snap-name> > /sys/bus/rbd/devices/<dev-id>/snap_rollback
snap_*
A directory per each snapshot
Entries under /sys/bus/rbd/devices/<dev-id>/snap_<snap-name>
-------------------------------------------------------------
id
The rados internal snapshot id assigned for this snapshot
size
The size of the image when this snapshot was taken.
Documentation/driver-model/interface.txt 已删除 100644 → 0
浏览文件 @ c451278c
Device Interfaces
Introduction
~~~~~~~~~~~~
Device interfaces are the logical interfaces of device classes that correlate
directly to userspace interfaces, like device nodes.
Each device class may have multiple interfaces through which you can
access the same device. An input device may support the mouse interface,
the 'evdev' interface, and the touchscreen interface. A SCSI disk would
support the disk interface, the SCSI generic interface, and possibly a raw
device interface.
Device interfaces are registered with the class they belong to. As devices
are added to the class, they are added to each interface registered with
the class. The interface is responsible for determining whether the device
supports the interface or not.
Programming Interface
~~~~~~~~~~~~~~~~~~~~~
struct device_interface {
char * name;
rwlock_t lock;
u32 devnum;
struct device_class * devclass;
struct list_head node;
struct driver_dir_entry dir;
int (*add_device)(struct device *);
int (*add_device)(struct intf_data *);
};
int interface_register(struct device_interface *);
void interface_unregister(struct device_interface *);
An interface must specify the device class it belongs to. It is added
to that class's list of interfaces on registration.
Interfaces can be added to a device class at any time. Whenever it is
added, each device in the class is passed to the interface's
add_device callback. When an interface is removed, each device is
removed from the interface.
Devices
~~~~~~~
Once a device is added to a device class, it is added to each
interface that is registered with the device class. The class
is expected to place a class-specific data structure in
struct device::class_data. The interface can use that (along with
other fields of struct device) to determine whether or not the driver
and/or device support that particular interface.
Data
~~~~
struct intf_data {
struct list_head node;
struct device_interface * intf;
struct device * dev;
u32 intf_num;
};
int interface_add_data(struct interface_data *);
The interface is responsible for allocating and initializing a struct
intf_data and calling interface_add_data() to add it to the device's list
of interfaces it belongs to. This list will be iterated over when the device
is removed from the class (instead of all possible interfaces for a class).
This structure should probably be embedded in whatever per-device data
structure the interface is allocating anyway.
Devices are enumerated within the interface. This happens in interface_add_data()
and the enumerated value is stored in the struct intf_data for that device.
sysfs
~~~~~
Each interface is given a directory in the directory of the device
class it belongs to:
Interfaces get a directory in the class's directory as well:
class/
`-- input
|-- devices
|-- drivers
|-- mouse
`-- evdev
When a device is added to the interface, a symlink is created that points
to the device's directory in the physical hierarchy:
class/
`-- input
|-- devices
| `-- 1 -> ../../../root/pci0/00:1f.0/usb_bus/00:1f.2-1:0/
|-- drivers
| `-- usb:usb_mouse -> ../../../bus/drivers/usb_mouse/
|-- mouse
| `-- 1 -> ../../../root/pci0/00:1f.0/usb_bus/00:1f.2-1:0/
`-- evdev
`-- 1 -> ../../../root/pci0/00:1f.0/usb_bus/00:1f.2-1:0/
Future Plans
~~~~~~~~~~~~
A device interface is correlated directly with a userspace interface
for a device, specifically a device node. For instance, a SCSI disk
exposes at least two interfaces to userspace: the standard SCSI disk
interface and the SCSI generic interface. It might also export a raw
device interface.
Many interfaces have a major number associated with them and each
device gets a minor number. Or, multiple interfaces might share one
major number, and each will receive a range of minor numbers (like in
the case of input devices).
These major and minor numbers could be stored in the interface
structure. Major and minor allocations could happen when the interface
is registered with the class, or via a helper function.
Documentation/filesystems/vfs.txt
浏览文件 @ 67b738ef
......@@ -660,11 +660,10 @@ struct address_space_operations {
releasepage: releasepage is called on PagePrivate pages to indicate
that the page should be freed if possible. ->releasepage
should remove any private data from the page and clear the
PagePrivate flag. It may also remove the page from the
address_space. If this fails for some reason, it may indicate
failure with a 0 return value.
This is used in two distinct though related cases. The first
is when the VM finds a clean page with no active users and
PagePrivate flag. If releasepage() fails for some reason, it must
indicate failure with a 0 return value.
releasepage() is used in two distinct though related cases. The
first is when the VM finds a clean page with no active users and
wants to make it a free page. If ->releasepage succeeds, the
page will be removed from the address_space and become free.
......
MAINTAINERS
浏览文件 @ 67b738ef
......@@ -2060,7 +2060,7 @@ F: Documentation/blockdev/drbd/
DRIVER CORE, KOBJECTS, DEBUGFS AND SYSFS
M: Greg Kroah-Hartman <gregkh@suse.de>
T: quilt kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6.git
S: Supported
F: Documentation/kobject.txt
F: drivers/base/
......@@ -2080,7 +2080,7 @@ F: include/drm/
INTEL DRM DRIVERS (excluding Poulsbo, Moorestown and derivative chipsets)
M: Chris Wilson <chris@chris-wilson.co.uk>
L: intel-gfx@lists.freedesktop.org
L: intel-gfx@lists.freedesktop.org (subscribers-only)
L: dri-devel@lists.freedesktop.org
T: git git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel.git
S: Supported
......@@ -4064,9 +4064,8 @@ F: drivers/scsi/NCR_D700.*
NETEFFECT IWARP RNIC DRIVER (IW_NES)
M: Faisal Latif <faisal.latif@intel.com>
M: Chien Tung <chien.tin.tung@intel.com>
L: linux-rdma@vger.kernel.org
W: http://www.neteffect.com
W: http://www.intel.com/Products/Server/Adapters/Server-Cluster/Server-Cluster-overview.htm
S: Supported
F: drivers/infiniband/hw/nes/
......
Makefile
浏览文件 @ 67b738ef
VERSION = 2
PATCHLEVEL = 6
SUBLEVEL = 37
EXTRAVERSION = -rc4
EXTRAVERSION = -rc5
NAME = Flesh-Eating Bats with Fangs
# *DOCUMENTATION*
......
arch/arm/Kconfig
浏览文件 @ 67b738ef
......@@ -9,7 +9,7 @@ config ARM
select GENERIC_ATOMIC64 if (!CPU_32v6K || !AEABI)
select HAVE_OPROFILE if (HAVE_PERF_EVENTS)
select HAVE_ARCH_KGDB
select HAVE_KPROBES if (!XIP_KERNEL)
select HAVE_KPROBES if (!XIP_KERNEL && !THUMB2_KERNEL)
select HAVE_KRETPROBES if (HAVE_KPROBES)
select HAVE_FUNCTION_TRACER if (!XIP_KERNEL)
select HAVE_FTRACE_MCOUNT_RECORD if (!XIP_KERNEL)
......
arch/arm/boot/Makefile
浏览文件 @ 67b738ef
......@@ -70,12 +70,7 @@ else
$(obj)/uImage: LOADADDR=$(ZRELADDR)
endif
ifeq ($(CONFIG_THUMB2_KERNEL),y)
# Set bit 0 to 1 so that "mov pc, rx" switches to Thumb-2 mode
$(obj)/uImage: STARTADDR=$(shell echo $(LOADADDR) | sed -e "s/.$$/1/")
else
$(obj)/uImage: STARTADDR=$(LOADADDR)
endif
$(obj)/uImage: $(obj)/zImage FORCE
$(call if_changed,uimage)
......
arch/arm/boot/bootp/init.S
浏览文件 @ 67b738ef
......@@ -73,6 +73,8 @@ move: ldmia r4!, {r7 - r10} @ move 32-bytes at a time
.size _start, . - _start
.align
.type data,#object
data: .word initrd_start @ source initrd address
.word initrd_phys @ destination initrd address
......
arch/arm/boot/compressed/head.S
浏览文件 @ 67b738ef
......@@ -125,9 +125,13 @@ wait: mrc p14, 0, pc, c0, c1, 0
* sort out different calling conventions
*/
.align
.arm @ Always enter in ARM state
start:
.type start,#function
.rept 8
THUMB( adr r12, BSYM(1f) )
THUMB( bx r12 )
THUMB( .rept 6 )
ARM( .rept 8 )
mov r0, r0
.endr
......@@ -135,6 +139,7 @@ start:
.word 0x016f2818 @ Magic numbers to help the loader
.word start @ absolute load/run zImage address
.word _edata @ zImage end address
THUMB( .thumb )
1: mov r7, r1 @ save architecture ID
mov r8, r2 @ save atags pointer
......@@ -174,7 +179,8 @@ not_angel:
ldr sp, [r0, #28]
#ifdef CONFIG_AUTO_ZRELADDR
@ determine final kernel image address
and r4, pc, #0xf8000000
mov r4, pc
and r4, r4, #0xf8000000
add r4, r4, #TEXT_OFFSET
#else
ldr r4, =zreladdr
......@@ -445,7 +451,8 @@ __setup_mmu: sub r3, r4, #16384 @ Page directory size
*/
mov r1, #0x1e
orr r1, r1, #3 << 10
mov r2, pc, lsr #20
mov r2, pc
mov r2, r2, lsr #20
orr r1, r1, r2, lsl #20
add r0, r3, r2, lsl #2
str r1, [r0], #4
......
arch/arm/common/gic.c
浏览文件 @ 67b738ef
......@@ -146,9 +146,15 @@ static int gic_set_cpu(unsigned int irq, const struct cpumask *mask_val)
unsigned int shift = (irq % 4) * 8;
unsigned int cpu = cpumask_first(mask_val);
u32 val;
struct irq_desc *desc;
spin_lock(&irq_controller_lock);
irq_desc[irq].node = cpu;
desc = irq_to_desc(irq);
if (desc == NULL) {
spin_unlock(&irq_controller_lock);
return -EINVAL;
}
desc->node = cpu;
val = readl(reg) & ~(0xff << shift);
val |= 1 << (cpu + shift);
writel(val, reg);
......@@ -210,7 +216,7 @@ void __init gic_cascade_irq(unsigned int gic_nr, unsigned int irq)
void __init gic_dist_init(unsigned int gic_nr, void __iomem *base,
unsigned int irq_start)
{
unsigned int max_irq, i;
unsigned int gic_irqs, irq_limit, i;
u32 cpumask = 1 << smp_processor_id();
if (gic_nr >= MAX_GIC_NR)
......@@ -226,47 +232,49 @@ void __init gic_dist_init(unsigned int gic_nr, void __iomem *base,
/*
* Find out how many interrupts are supported.
*/
max_irq = readl(base + GIC_DIST_CTR) & 0x1f;
max_irq = (max_irq + 1) * 32;
/*
* The GIC only supports up to 1020 interrupt sources.
* Limit this to either the architected maximum, or the
* platform maximum.
*/
if (max_irq > max(1020, NR_IRQS))
max_irq = max(1020, NR_IRQS);
gic_irqs = readl(base + GIC_DIST_CTR) & 0x1f;
gic_irqs = (gic_irqs + 1) * 32;
if (gic_irqs > 1020)
gic_irqs = 1020;
/*
* Set all global interrupts to be level triggered, active low.
*/
for (i = 32; i < max_irq; i += 16)
for (i = 32; i < gic_irqs; i += 16)
writel(0, base + GIC_DIST_CONFIG + i * 4 / 16);
/*
* Set all global interrupts to this CPU only.
*/
for (i = 32; i < max_irq; i += 4)
for (i = 32; i < gic_irqs; i += 4)
writel(cpumask, base + GIC_DIST_TARGET + i * 4 / 4);
/*
* Set priority on all global interrupts.
*/
for (i = 32; i < max_irq; i += 4)
for (i = 32; i < gic_irqs; i += 4)
writel(0xa0a0a0a0, base + GIC_DIST_PRI + i * 4 / 4);
/*
* Disable all interrupts. Leave the PPI and SGIs alone
* as these enables are banked registers.
*/
for (i = 32; i < max_irq; i += 32)
for (i = 32; i < gic_irqs; i += 32)
writel(0xffffffff, base + GIC_DIST_ENABLE_CLEAR + i * 4 / 32);
/*
* Limit number of interrupts registered to the platform maximum
*/
irq_limit = gic_data[gic_nr].irq_offset + gic_irqs;
if (WARN_ON(irq_limit > NR_IRQS))
irq_limit = NR_IRQS;
/*
* Setup the Linux IRQ subsystem.
*/
for (i = irq_start; i < gic_data[gic_nr].irq_offset + max_irq; i++) {
for (i = irq_start; i < irq_limit; i++) {
set_irq_chip(i, &gic_chip);
set_irq_chip_data(i, &gic_data[gic_nr]);
set_irq_handler(i, handle_level_irq);
......
arch/arm/configs/picotux200_defconfig → arch/arm/configs/at91rm9200_defconfig
浏览文件 @ 67b738ef
CONFIG_EXPERIMENTAL=y
# CONFIG_LOCALVERSION_AUTO is not set
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_IKCONFIG=m
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EMBEDDED=y
# CONFIG_KALLSYMS is not set
CONFIG_SLAB=y
CONFIG_SYSFS_DEPRECATED_V2=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_MODULES=y
CONFIG_MODULE_FORCE_LOAD=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_IOSCHED_DEADLINE is not set
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_IOSCHED_CFQ is not set
CONFIG_ARCH_AT91=y
CONFIG_MACH_ONEARM=y
CONFIG_ARCH_AT91RM9200DK=y
CONFIG_MACH_AT91RM9200EK=y
CONFIG_MACH_CSB337=y
CONFIG_MACH_CSB637=y
CONFIG_MACH_CARMEVA=y
CONFIG_MACH_ATEB9200=y
CONFIG_MACH_KB9200=y
CONFIG_MACH_PICOTUX2XX=y
CONFIG_MACH_KAFA=y
CONFIG_MACH_ECBAT91=y
CONFIG_MACH_YL9200=y
CONFIG_MACH_CPUAT91=y
CONFIG_MACH_ECO920=y
CONFIG_MTD_AT91_DATAFLASH_CARD=y
CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
CONFIG_AT91_TIMER_HZ=100
# CONFIG_ARM_THUMB is not set
CONFIG_PCCARD=y
CONFIG_AT91_CF=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_PREEMPT=y
CONFIG_AEABI=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_LEDS=y
CONFIG_LEDS_CPU=y
CONFIG_ZBOOT_ROM_TEXT=0x10000000
CONFIG_ZBOOT_ROM_BSS=0x20040000
CONFIG_KEXEC=y
CONFIG_FPE_NWFPE=y
CONFIG_BINFMT_MISC=m
CONFIG_BINFMT_MISC=y
CONFIG_NET=y
CONFIG_PACKET=m
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_XFRM_USER=m
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
......@@ -34,7 +63,6 @@ CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
CONFIG_INET_DIAG=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
CONFIG_IPV6_ROUTE_INFO=y
......@@ -55,26 +83,50 @@ CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_HIDP=m
CONFIG_FW_LOADER=m
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_MTD=y
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_AFS_PARTS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_CFI=y
CONFIG_MTD_JEDECPROBE=y
CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_CFI_AMDSTD=y
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP=y
CONFIG_BLK_DEV_LOOP=m
CONFIG_MTD_PLATRAM=y
CONFIG_MTD_DATAFLASH=y
CONFIG_MTD_NAND=y
CONFIG_MTD_NAND_ATMEL=y
CONFIG_MTD_NAND_PLATFORM=y
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_GLUEBI=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_NBD=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_ATMEL_TCLIB=y
CONFIG_EEPROM_LEGACY=m
CONFIG_SCSI=m
CONFIG_BLK_DEV_SD=m
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_BLK_DEV_SR=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_MULTI_LUN=y
# CONFIG_SCSI_LOWLEVEL is not set
CONFIG_NETDEVICES=y
CONFIG_TUN=m
CONFIG_PHYLIB=y
CONFIG_DAVICOM_PHY=y
CONFIG_SMSC_PHY=y
CONFIG_MICREL_PHY=y
CONFIG_NET_ETHERNET=y
CONFIG_ARM_AT91_ETHER=y
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
......@@ -83,34 +135,40 @@ CONFIG_USB_USBNET=m
CONFIG_USB_NET_DM9601=m
CONFIG_USB_NET_GL620A=m
CONFIG_USB_NET_PLUSB=m
CONFIG_USB_NET_MCS7830=m
CONFIG_USB_NET_RNDIS_HOST=m
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_KC2190=y
CONFIG_PPP=m
CONFIG_PPP=y
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPP_ASYNC=y
CONFIG_PPP_DEFLATE=y
CONFIG_PPP_BSDCOMP=y
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=640
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=480
CONFIG_INPUT_EVDEV=y
CONFIG_KEYBOARD_GPIO=y
# CONFIG_INPUT_MOUSE is not set
# CONFIG_SERIO is not set
# CONFIG_VT is not set
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_SERIAL_ATMEL=y
CONFIG_SERIAL_ATMEL_CONSOLE=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_I2C=m
CONFIG_I2C_CHARDEV=m
CONFIG_I2C_GPIO=m
CONFIG_LEGACY_PTY_COUNT=32
CONFIG_HW_RANDOM=y
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_GPIO=y
CONFIG_SPI=y
CONFIG_SPI_ATMEL=y
CONFIG_SPI_BITBANG=y
CONFIG_GPIO_SYSFS=y
CONFIG_HWMON=m
CONFIG_SENSORS_ADM1021=m
CONFIG_SENSORS_ADM1025=m
......@@ -123,6 +181,7 @@ CONFIG_SENSORS_GL518SM=m
CONFIG_SENSORS_GL520SM=m
CONFIG_SENSORS_IT87=m
CONFIG_SENSORS_LM63=m
CONFIG_SENSORS_LM73=m
CONFIG_SENSORS_LM75=m
CONFIG_SENSORS_LM77=m
CONFIG_SENSORS_LM78=m
......@@ -142,42 +201,100 @@ CONFIG_SENSORS_W83793=m
CONFIG_SENSORS_W83L785TS=m
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_NOWAYOUT=y
CONFIG_AT91RM9200_WATCHDOG=m
CONFIG_HID=m
CONFIG_USB=m
CONFIG_AT91RM9200_WATCHDOG=y
CONFIG_FB=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
CONFIG_FB_S1D13XXX=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_BACKLIGHT_CLASS_DEVICE=y
# CONFIG_BACKLIGHT_GENERIC is not set
CONFIG_DISPLAY_SUPPORT=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FONTS=y
CONFIG_FONT_MINI_4x6=y
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_USB=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_DEVICE_CLASS is not set
CONFIG_USB_MON=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
CONFIG_USB_STORAGE=m
CONFIG_USB_SERIAL=m
CONFIG_USB_STORAGE=y
CONFIG_USB_SERIAL=y
CONFIG_USB_SERIAL_CONSOLE=y
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_PL2303=m
CONFIG_MMC=m
CONFIG_MMC_AT91=m
CONFIG_RTC_CLASS=m
CONFIG_RTC_DRV_AT91RM9200=m
CONFIG_EXT2_FS=m
CONFIG_EXT3_FS=m
CONFIG_USB_SERIAL_FTDI_SIO=y
CONFIG_USB_SERIAL_KEYSPAN=y
CONFIG_USB_SERIAL_KEYSPAN_MPR=y
CONFIG_USB_SERIAL_KEYSPAN_USA28=y
CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
CONFIG_USB_SERIAL_KEYSPAN_USA19=y
CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
CONFIG_USB_SERIAL_MCT_U232=y
CONFIG_USB_SERIAL_PL2303=y
CONFIG_USB_GADGET=y
CONFIG_USB_ETH=m
CONFIG_USB_MASS_STORAGE=m
CONFIG_MMC=y
CONFIG_MMC_AT91=y
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
CONFIG_LEDS_GPIO=y
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
CONFIG_LEDS_TRIGGER_GPIO=y
CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
CONFIG_RTC_CLASS=y
# CONFIG_RTC_HCTOSYS is not set
CONFIG_RTC_DRV_DS1307=y
CONFIG_RTC_DRV_PCF8563=y
CONFIG_RTC_DRV_AT91RM9200=y
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
CONFIG_INOTIFY=y
CONFIG_ISO9660_FS=m
CONFIG_REISERFS_FS=y
CONFIG_AUTOFS4_FS=y
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_UDF_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_ZISOFS=y
CONFIG_UDF_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_NTFS_FS=m
CONFIG_TMPFS=y
CONFIG_CONFIGFS_FS=y
CONFIG_JFFS2_FS=y
CONFIG_JFFS2_SUMMARY=y
CONFIG_JFFS2_COMPRESSION_OPTIONS=y
CONFIG_NFS_FS=m
CONFIG_JFFS2_LZO=y
CONFIG_JFFS2_RUBIN=y
CONFIG_CRAMFS=y
CONFIG_MINIX_FS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_ROOT_NFS=y
CONFIG_NFSD=y
CONFIG_SMB_FS=m
CONFIG_CIFS=m
CONFIG_PARTITION_ADVANCED=y
CONFIG_AMIGA_PARTITION=y
CONFIG_NLS_DEFAULT="utf-8"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_MAC_PARTITION=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
......@@ -201,7 +318,7 @@ CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
......@@ -214,29 +331,11 @@ CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m
CONFIG_NLS_UTF8=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_DEBUG_FS=y
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_BUGVERBOSE is not set
CONFIG_DEBUG_LL=y
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_XCBC=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_FCRYPT=m
CONFIG_CRYPTO_KHAZAD=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_LIBCRC32C=m
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_FTRACE is not set
CONFIG_CRYPTO_PCBC=y
CONFIG_CRYPTO_SHA1=y
arch/arm/configs/at91rm9200dk_defconfig 已删除 100644 → 0
浏览文件 @ c451278c
CONFIG_EXPERIMENTAL=y
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_BLK_DEV_INITRD=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_IOSCHED_DEADLINE is not set
# CONFIG_IOSCHED_CFQ is not set
CONFIG_ARCH_AT91=y
CONFIG_ARCH_AT91RM9200DK=y
CONFIG_MACH_ECO920=y
CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
# CONFIG_ARM_THUMB is not set
CONFIG_PCCARD=y
CONFIG_AT91_CF=y
CONFIG_LEDS=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="mem=32M console=ttyS0,115200 initrd=0x20410000,3145728 root=/dev/ram0 rw"
CONFIG_FPE_NWFPE=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_BOOTP=y
# CONFIG_IPV6 is not set
CONFIG_MTD=y
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_CFI=y
CONFIG_MTD_JEDECPROBE=y
CONFIG_MTD_CFI_AMDSTD=y
CONFIG_MTD_PHYSMAP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_NETDEVICES=y
CONFIG_NET_ETHERNET=y
CONFIG_ARM_AT91_ETHER=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_SERIO is not set
CONFIG_SERIAL_ATMEL=y
CONFIG_SERIAL_ATMEL_CONSOLE=y
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_GPIO=y
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_NOWAYOUT=y
CONFIG_AT91RM9200_WATCHDOG=y
# CONFIG_VGA_CONSOLE is not set
# CONFIG_USB_HID is not set
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_MON=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_GADGET=y
CONFIG_MMC=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_AT91RM9200=y
CONFIG_EXT2_FS=y
CONFIG_INOTIFY=y
CONFIG_TMPFS=y
CONFIG_CRAMFS=y
CONFIG_DEBUG_KERNEL=y
CONFIG_DEBUG_USER=y
CONFIG_DEBUG_LL=y
arch/arm/configs/at91rm9200ek_defconfig 已删除 100644 → 0
浏览文件 @ c451278c
CONFIG_EXPERIMENTAL=y
# CONFIG_LOCALVERSION_AUTO is not set
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_BLK_DEV_INITRD=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_IOSCHED_DEADLINE is not set
# CONFIG_IOSCHED_CFQ is not set
CONFIG_ARCH_AT91=y
CONFIG_MACH_AT91RM9200EK=y
CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
# CONFIG_ARM_THUMB is not set
CONFIG_LEDS=y
CONFIG_LEDS_CPU=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="mem=32M console=ttyS0,115200 initrd=0x20410000,3145728 root=/dev/ram0 rw"
CONFIG_FPE_NWFPE=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_BOOTP=y
# CONFIG_IPV6 is not set
CONFIG_MTD=y
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_CFI=y
CONFIG_MTD_JEDECPROBE=y
CONFIG_MTD_CFI_AMDSTD=y
CONFIG_MTD_PHYSMAP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_NETDEVICES=y
CONFIG_NET_ETHERNET=y
CONFIG_ARM_AT91_ETHER=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_SERIO is not set
CONFIG_SERIAL_ATMEL=y
CONFIG_SERIAL_ATMEL_CONSOLE=y
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_GPIO=y
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_NOWAYOUT=y
CONFIG_AT91RM9200_WATCHDOG=y
CONFIG_FB=y
CONFIG_FB_S1D13XXX=y
# CONFIG_VGA_CONSOLE is not set
# CONFIG_USB_HID is not set
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_MON=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_GADGET=y
CONFIG_MMC=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_AT91RM9200=y
CONFIG_EXT2_FS=y
CONFIG_INOTIFY=y
CONFIG_TMPFS=y
CONFIG_CRAMFS=y
CONFIG_DEBUG_KERNEL=y
CONFIG_DEBUG_USER=y
CONFIG_DEBUG_LL=y
arch/arm/configs/ateb9200_defconfig 已删除 100644 → 0
浏览文件 @ c451278c
CONFIG_EXPERIMENTAL=y
CONFIG_SYSVIPC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EMBEDDED=y
CONFIG_SLAB=y
CONFIG_PROFILING=y
CONFIG_OPROFILE=m
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_ARCH_AT91=y
CONFIG_MACH_ATEB9200=y
CONFIG_PCCARD=m
CONFIG_AT91_CF=m
CONFIG_PREEMPT=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_FPE_NWFPE=y
CONFIG_PM=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_NET_KEY=y
CONFIG_INET=y
# CONFIG_IPV6 is not set
CONFIG_BRIDGE=m
CONFIG_VLAN_8021Q=m
CONFIG_MTD=y
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK_RO=y
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_SCSI=m
CONFIG_BLK_DEV_SD=m
CONFIG_BLK_DEV_SR=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_MULTI_LUN=y
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
CONFIG_TUN=m
CONFIG_PHYLIB=y
CONFIG_DAVICOM_PHY=y
CONFIG_NET_ETHERNET=y
CONFIG_ARM_AT91_ETHER=y
CONFIG_USB_USBNET=y
CONFIG_USB_NET_GL620A=y
CONFIG_USB_NET_PLUSB=y
CONFIG_USB_NET_RNDIS_HOST=y
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_EPSON2888=y
CONFIG_PPP=m
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPPOE=m
CONFIG_SERIAL_ATMEL=y
CONFIG_SERIAL_ATMEL_CONSOLE=y
CONFIG_I2C=m
CONFIG_I2C_CHARDEV=m
CONFIG_I2C_GPIO=m
# CONFIG_VGA_CONSOLE is not set
CONFIG_SOUND=y
CONFIG_USB_HID=m
CONFIG_HID_PID=y
CONFIG_USB_HIDDEV=y
CONFIG_USB=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_MON=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
CONFIG_USB_STORAGE=m
CONFIG_USB_STORAGE_DATAFAB=m
CONFIG_USB_STORAGE_FREECOM=m
CONFIG_USB_STORAGE_USBAT=m
CONFIG_USB_STORAGE_SDDR09=m
CONFIG_USB_STORAGE_SDDR55=m
CONFIG_USB_STORAGE_JUMPSHOT=m
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_PL2303=m
CONFIG_USB_GADGET=m
CONFIG_USB_ETH=m
CONFIG_USB_GADGETFS=m
CONFIG_USB_FILE_STORAGE=m
CONFIG_USB_G_SERIAL=m
CONFIG_MMC=m
CONFIG_MMC_DEBUG=y
CONFIG_RTC_CLASS=y
# CONFIG_RTC_HCTOSYS is not set
CONFIG_RTC_DRV_AT91RM9200=y
CONFIG_EXT2_FS=m
CONFIG_EXT3_FS=m
CONFIG_REISERFS_FS=m
CONFIG_INOTIFY=y
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_NTFS_FS=m
CONFIG_NTFS_RW=y
CONFIG_TMPFS=y
CONFIG_CRAMFS=y
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_NFSD=m
CONFIG_NFSD_V4=y
CONFIG_PARTITION_ADVANCED=y
CONFIG_MAC_PARTITION=y
CONFIG_BSD_DISKLABEL=y
CONFIG_MINIX_SUBPARTITION=y
CONFIG_SOLARIS_X86_PARTITION=y
CONFIG_UNIXWARE_DISKLABEL=y
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_UTF8=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRC16=m
CONFIG_LIBCRC32C=m
arch/arm/configs/carmeva_defconfig 已删除 100644 → 0
浏览文件 @ c451278c
CONFIG_EXPERIMENTAL=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_BLK_DEV_INITRD=y
CONFIG_EMBEDDED=y
# CONFIG_HOTPLUG is not set
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_ARCH_AT91=y
CONFIG_MACH_CARMEVA=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_FPE_NWFPE=y
CONFIG_NET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_PNP=y
# CONFIG_IPV6 is not set
CONFIG_MTD=y
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_BLK_DEV_RAM=y
CONFIG_NETDEVICES=y
CONFIG_NET_ETHERNET=y
CONFIG_ARM_AT91_ETHER=y
# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
CONFIG_SERIO=m
CONFIG_SERIAL_ATMEL=y
CONFIG_SERIAL_ATMEL_CONSOLE=y
# CONFIG_VGA_CONSOLE is not set
CONFIG_MMC=m
CONFIG_MMC_DEBUG=y
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
# CONFIG_DNOTIFY is not set
CONFIG_JFFS2_FS=y
CONFIG_JFFS2_COMPRESSION_OPTIONS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
CONFIG_ROOT_NFS=y
CONFIG_NFSD=y
arch/arm/configs/cpuat91_defconfig 已删除 100644 → 0
浏览文件 @ c451278c
CONFIG_EXPERIMENTAL=y
# CONFIG_LOCALVERSION_AUTO is not set
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED_V2=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_IOSCHED_CFQ is not set
CONFIG_ARCH_AT91=y
CONFIG_MACH_CPUAT91=y
CONFIG_AT91_TIMER_HZ=100
# CONFIG_ARM_THUMB is not set
CONFIG_PREEMPT=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_PNP=y
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
# CONFIG_IPV6 is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_MTD=y
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_CFI=y
CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_PLATRAM=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_NBD=y
CONFIG_BLK_DEV_RAM=y
# CONFIG_MISC_DEVICES is not set
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_SCSI_MULTI_LUN=y
# CONFIG_SCSI_LOWLEVEL is not set
CONFIG_NETDEVICES=y
CONFIG_PHYLIB=y
CONFIG_NET_ETHERNET=y
CONFIG_ARM_AT91_ETHER=y
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
CONFIG_PPP=y
CONFIG_PPP_ASYNC=y
CONFIG_PPP_DEFLATE=y
CONFIG_PPP_BSDCOMP=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_SERIO is not set
CONFIG_SERIAL_ATMEL=y
CONFIG_SERIAL_ATMEL_CONSOLE=y
CONFIG_LEGACY_PTY_COUNT=32
# CONFIG_HW_RANDOM is not set
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_GPIO=y
CONFIG_GPIO_SYSFS=y
# CONFIG_HWMON is not set
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_NOWAYOUT=y
CONFIG_AT91RM9200_WATCHDOG=y
# CONFIG_VGA_CONSOLE is not set
# CONFIG_HID_SUPPORT is not set
CONFIG_USB=y
# CONFIG_USB_DEVICE_CLASS is not set
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_ETH=m
CONFIG_MMC=y
CONFIG_MMC_AT91=m
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
CONFIG_LEDS_GPIO=y
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
CONFIG_LEDS_TRIGGER_GPIO=y
CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
CONFIG_RTC_CLASS=y
# CONFIG_RTC_HCTOSYS is not set
CONFIG_RTC_DRV_DS1307=y
CONFIG_RTC_DRV_PCF8563=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
CONFIG_INOTIFY=y
CONFIG_AUTOFS4_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_TMPFS=y
CONFIG_JFFS2_FS=y
CONFIG_JFFS2_SUMMARY=y
CONFIG_CRAMFS=y
CONFIG_MINIX_FS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_ROOT_NFS=y
CONFIG_PARTITION_ADVANCED=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_UTF8=y
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
arch/arm/configs/csb337_defconfig 已删除 100644 → 0
浏览文件 @ c451278c
CONFIG_EXPERIMENTAL=y
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_BLK_DEV_INITRD=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_BLK_DEV_BSG is not set
CONFIG_ARCH_AT91=y
CONFIG_MACH_CSB337=y
CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
# CONFIG_ARM_THUMB is not set
CONFIG_PCCARD=y
CONFIG_AT91_CF=y
CONFIG_LEDS=y
CONFIG_LEDS_CPU=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="mem=32M console=ttyS0,38400 initrd=0x20410000,3145728 root=/dev/ram0 rw"
CONFIG_FPE_NWFPE=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
# CONFIG_INET_LRO is not set
# CONFIG_IPV6 is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_MTD=y
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_CFI=y
CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_PHYSMAP=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_ATMEL_SSC=y
CONFIG_SCSI=y
CONFIG_NETDEVICES=y
CONFIG_NET_ETHERNET=y
CONFIG_ARM_AT91_ETHER=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_SERIO is not set
CONFIG_SERIAL_ATMEL=y
CONFIG_SERIAL_ATMEL_CONSOLE=y
# CONFIG_HW_RANDOM is not set
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_GPIO=y
# CONFIG_HWMON is not set
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_NOWAYOUT=y
CONFIG_AT91RM9200_WATCHDOG=y
# CONFIG_VGA_CONSOLE is not set
# CONFIG_USB_HID is not set
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_MON=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_SERIAL=y
CONFIG_USB_SERIAL_CONSOLE=y
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_FTDI_SIO=y
CONFIG_USB_SERIAL_KEYSPAN=y
CONFIG_USB_SERIAL_KEYSPAN_MPR=y
CONFIG_USB_SERIAL_KEYSPAN_USA28=y
CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
CONFIG_USB_SERIAL_KEYSPAN_USA19=y
CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
CONFIG_USB_SERIAL_MCT_U232=y
CONFIG_USB_GADGET=y
CONFIG_MMC=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS_DEVICE="rtc1"
# CONFIG_RTC_INTF_SYSFS is not set
CONFIG_RTC_DRV_DS1307=y
CONFIG_RTC_DRV_AT91RM9200=y
CONFIG_EXT2_FS=y
CONFIG_INOTIFY=y
CONFIG_TMPFS=y
CONFIG_CRAMFS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
CONFIG_ROOT_NFS=y
CONFIG_DEBUG_KERNEL=y
CONFIG_DEBUG_USER=y
CONFIG_DEBUG_LL=y
arch/arm/configs/csb637_defconfig 已删除 100644 → 0
浏览文件 @ c451278c
CONFIG_EXPERIMENTAL=y
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED_V2=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_BLK_DEV_BSG is not set
CONFIG_ARCH_AT91=y
CONFIG_MACH_CSB637=y
CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
# CONFIG_ARM_THUMB is not set
CONFIG_PCCARD=y
CONFIG_AT91_CF=y
CONFIG_LEDS=y
CONFIG_LEDS_CPU=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="mem=32M console=ttyS0,38400 initrd=0x20410000,3145728 root=/dev/ram0 rw"
CONFIG_FPE_NWFPE=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
# CONFIG_INET_LRO is not set
# CONFIG_IPV6 is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_MTD=y
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_CFI=y
CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_PHYSMAP=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_SCSI=y
CONFIG_NETDEVICES=y
CONFIG_NET_ETHERNET=y
CONFIG_ARM_AT91_ETHER=y
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_SERIO is not set
CONFIG_SERIAL_ATMEL=y
CONFIG_SERIAL_ATMEL_CONSOLE=y
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_NOWAYOUT=y
CONFIG_AT91RM9200_WATCHDOG=y
# CONFIG_VGA_CONSOLE is not set
# CONFIG_USB_HID is not set
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_MON=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_SERIAL=y
CONFIG_USB_SERIAL_CONSOLE=y
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_FTDI_SIO=y
CONFIG_USB_SERIAL_KEYSPAN=y
CONFIG_USB_SERIAL_KEYSPAN_MPR=y
CONFIG_USB_SERIAL_KEYSPAN_USA28=y
CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
CONFIG_USB_SERIAL_KEYSPAN_USA19=y
CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
CONFIG_USB_SERIAL_MCT_U232=y
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
CONFIG_LEDS_GPIO=y
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
CONFIG_EXT2_FS=y
CONFIG_INOTIFY=y
CONFIG_TMPFS=y
CONFIG_CRAMFS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
CONFIG_ROOT_NFS=y
CONFIG_DEBUG_KERNEL=y
CONFIG_DEBUG_USER=y
CONFIG_DEBUG_LL=y
arch/arm/configs/ecbat91_defconfig 已删除 100644 → 0
浏览文件 @ c451278c
CONFIG_EXPERIMENTAL=y
CONFIG_SYSVIPC=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_IOSCHED_DEADLINE is not set
# CONFIG_IOSCHED_CFQ is not set
CONFIG_ARCH_AT91=y
CONFIG_MACH_ECBAT91=y
CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
CONFIG_PCCARD=y
CONFIG_AT91_CF=y
CONFIG_PREEMPT=y
CONFIG_LEDS=y
CONFIG_LEDS_CPU=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="rootfstype=reiserfs root=/dev/mmcblk0p1 console=ttyS0,115200n8 rootdelay=1"
CONFIG_FPE_NWFPE=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
# CONFIG_IPV6 is not set
CONFIG_CFG80211=y
CONFIG_MAC80211=y
# CONFIG_STANDALONE is not set
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
CONFIG_MTD=y
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_AFS_PARTS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_DATAFLASH=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_SG=y
CONFIG_NETDEVICES=y
CONFIG_NET_ETHERNET=y
CONFIG_ARM_AT91_ETHER=y
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
CONFIG_PPP=y
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_SERIO is not set
CONFIG_SERIAL_ATMEL=y
CONFIG_SERIAL_ATMEL_CONSOLE=y
CONFIG_HW_RANDOM=y
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_SPI=y
CONFIG_SPI_BITBANG=y
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_NOWAYOUT=y
# CONFIG_VGA_CONSOLE is not set
# CONFIG_USB_HID is not set
CONFIG_USB=y
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_DEVICE_CLASS is not set
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_PRINTER=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_MMC=y
CONFIG_MMC_DEBUG=y
CONFIG_MMC_AT91=m
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
CONFIG_RTC_CLASS=y
# CONFIG_RTC_HCTOSYS is not set
CONFIG_RTC_DRV_AT91RM9200=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
CONFIG_REISERFS_FS=y
CONFIG_INOTIFY=y
CONFIG_TMPFS=y
CONFIG_CONFIGFS_FS=y
CONFIG_CRAMFS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_ROOT_NFS=y
CONFIG_PARTITION_ADVANCED=y
CONFIG_DEBUG_USER=y
CONFIG_CRYPTO_PCBC=y
CONFIG_CRYPTO_SHA1=y
arch/arm/configs/kafa_defconfig 已删除 100644 → 0
浏览文件 @ c451278c
CONFIG_EXPERIMENTAL=y
# CONFIG_LOCALVERSION_AUTO is not set
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_IOSCHED_CFQ is not set
CONFIG_ARCH_AT91=y
CONFIG_MACH_KAFA=y
# CONFIG_ARM_THUMB is not set
CONFIG_PREEMPT=y
CONFIG_LEDS=y
CONFIG_LEDS_CPU=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="mem=32M console=ttyS0,115200 initrd=0x20800000,10M root=/dev/ram0 rw"
CONFIG_FPE_NWFPE=y
CONFIG_BINFMT_MISC=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
# CONFIG_INET_DIAG is not set
# CONFIG_IPV6 is not set
CONFIG_MTD=y
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK_RO=y
CONFIG_NETDEVICES=y
CONFIG_PHYLIB=y
CONFIG_DAVICOM_PHY=y
CONFIG_NET_ETHERNET=y
CONFIG_ARM_AT91_ETHER=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_SERIO is not set
CONFIG_SERIAL_ATMEL=y
CONFIG_SERIAL_ATMEL_CONSOLE=y
CONFIG_LEGACY_PTY_COUNT=32
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_GPIO=y
# CONFIG_HWMON is not set
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_NOWAYOUT=y
CONFIG_AT91RM9200_WATCHDOG=y
# CONFIG_VGA_CONSOLE is not set
CONFIG_RTC_CLASS=y
# CONFIG_RTC_HCTOSYS is not set
CONFIG_RTC_DRV_AT91RM9200=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
CONFIG_TMPFS=y
CONFIG_CRAMFS=y
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_DES=y
arch/arm/configs/kb9202_defconfig 已删除 100644 → 0
浏览文件 @ c451278c
CONFIG_EXPERIMENTAL=y
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_AUDIT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_KALLSYMS_EXTRA_PASS=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_IOSCHED_DEADLINE is not set
CONFIG_ARCH_AT91=y
CONFIG_MACH_KB9200=y
CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_PREEMPT=y
CONFIG_AEABI=y
CONFIG_ZBOOT_ROM_TEXT=0x10000000
CONFIG_ZBOOT_ROM_BSS=0x20040000
CONFIG_CMDLINE="noinitrd root=/dev/mtdblock0 rootfstype=jffs2 mem=64M"
CONFIG_KEXEC=y
CONFIG_FPE_NWFPE=y
CONFIG_BINFMT_MISC=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
# CONFIG_INET_LRO is not set
# CONFIG_INET_DIAG is not set
# CONFIG_IPV6 is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
# CONFIG_FIRMWARE_IN_KERNEL is not set
CONFIG_MTD=y
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_CFI=y
CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_NAND=y
CONFIG_MTD_NAND_ATMEL=y
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_GLUEBI=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=16384
CONFIG_ATMEL_TCLIB=y
CONFIG_ATMEL_SSC=y
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_SG=y
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
CONFIG_SCSI_SPI_ATTRS=m
# CONFIG_SCSI_LOWLEVEL is not set
CONFIG_NETDEVICES=y
CONFIG_NET_ETHERNET=y
CONFIG_ARM_AT91_ETHER=y
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_SERIO is not set
CONFIG_SERIAL_ATMEL=y
CONFIG_SERIAL_ATMEL_CONSOLE=y
# CONFIG_LEGACY_PTYS is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_HWMON is not set
CONFIG_WATCHDOG=y
CONFIG_AT91RM9200_WATCHDOG=y
CONFIG_FB=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
# CONFIG_LCD_CLASS_DEVICE is not set
CONFIG_BACKLIGHT_CLASS_DEVICE=y
# CONFIG_BACKLIGHT_GENERIC is not set
# CONFIG_VGA_CONSOLE is not set
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FONTS=y
CONFIG_FONT_MINI_4x6=y
# CONFIG_HID_SUPPORT is not set
CONFIG_USB=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_LIBUSUAL=y
CONFIG_MMC=y
CONFIG_MMC_AT91=m
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_AT91RM9200=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_DNOTIFY is not set
CONFIG_INOTIFY=y
CONFIG_VFAT_FS=y
CONFIG_TMPFS=y
CONFIG_CONFIGFS_FS=y
CONFIG_JFFS2_FS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_ROOT_NFS=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_UTF8=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_DEBUG_FS=y
CONFIG_DEBUG_KERNEL=y
# CONFIG_SCHED_DEBUG is not set
# CONFIG_DEBUG_PREEMPT is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
arch/arm/configs/onearm_defconfig 已删除 100644 → 0
浏览文件 @ c451278c
CONFIG_EXPERIMENTAL=y
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_BLK_DEV_INITRD=y
CONFIG_EMBEDDED=y
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_IOSCHED_DEADLINE is not set
# CONFIG_IOSCHED_CFQ is not set
CONFIG_ARCH_AT91=y
CONFIG_MACH_ONEARM=y
CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
# CONFIG_ARM_THUMB is not set
CONFIG_PCCARD=y
CONFIG_AT91_CF=y
CONFIG_LEDS=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="console=ttyS0,115200 root=/dev/nfs ip=bootp mem=64M"
CONFIG_FPE_NWFPE=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IPV6=y
# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
# CONFIG_INET6_XFRM_MODE_BEET is not set
# CONFIG_IPV6_SIT is not set
CONFIG_MTD=y
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_CFI=y
CONFIG_MTD_JEDECPROBE=y
CONFIG_MTD_CFI_AMDSTD=y
CONFIG_MTD_PHYSMAP=y
CONFIG_BLK_DEV_NBD=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_NETDEVICES=y
CONFIG_NET_ETHERNET=y
CONFIG_ARM_AT91_ETHER=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_SERIO is not set
# CONFIG_VT is not set
CONFIG_SERIAL_ATMEL=y
CONFIG_SERIAL_ATMEL_CONSOLE=y
# CONFIG_HW_RANDOM is not set
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_NOWAYOUT=y
CONFIG_AT91RM9200_WATCHDOG=y
# CONFIG_USB_HID is not set
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_MON=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_GADGET=y
CONFIG_MMC=y
CONFIG_EXT2_FS=y
CONFIG_INOTIFY=y
CONFIG_TMPFS=y
CONFIG_CRAMFS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_ROOT_NFS=y
CONFIG_DEBUG_KERNEL=y
CONFIG_DEBUG_USER=y
CONFIG_DEBUG_LL=y
arch/arm/configs/yl9200_defconfig 已删除 100644 → 0
浏览文件 @ c451278c
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_BLK_DEV_INITRD=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_IOSCHED_DEADLINE is not set
# CONFIG_IOSCHED_CFQ is not set
CONFIG_ARCH_AT91=y
CONFIG_ARCH_AT91RM9200DK=y
CONFIG_MACH_YL9200=y
# CONFIG_ARM_THUMB is not set
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="mem=32M console=ttyS0,115200 initrd=0x20410000,3145728 root=/dev/ram0 rw"
CONFIG_FPE_NWFPE=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
# CONFIG_INET_LRO is not set
# CONFIG_INET_DIAG is not set
# CONFIG_IPV6 is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_MTD=y
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_MTD_CFI=y
CONFIG_MTD_JEDECPROBE=y
CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_PLATRAM=y
CONFIG_MTD_NAND=y
CONFIG_MTD_NAND_ATMEL=y
CONFIG_MTD_NAND_PLATFORM=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=3
CONFIG_BLK_DEV_RAM_SIZE=8192
# CONFIG_MISC_DEVICES is not set
CONFIG_BLK_DEV_SD=y
CONFIG_ATA=y
CONFIG_NETDEVICES=y
CONFIG_PHYLIB=y
CONFIG_DAVICOM_PHY=y
CONFIG_NET_ETHERNET=y
CONFIG_ARM_AT91_ETHER=y
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=640
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=480
CONFIG_INPUT_EVDEV=y
# CONFIG_KEYBOARD_ATKBD is not set
CONFIG_KEYBOARD_GPIO=y
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_ADS7846=y
# CONFIG_SERIO_SERPORT is not set
CONFIG_SERIAL_ATMEL=y
CONFIG_SERIAL_ATMEL_CONSOLE=y
# CONFIG_HW_RANDOM is not set
CONFIG_I2C=y
CONFIG_SPI=y
CONFIG_SPI_DEBUG=y
CONFIG_SPI_ATMEL=y
CONFIG_FB=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_BACKLIGHT_CLASS_DEVICE=y
CONFIG_DISPLAY_SUPPORT=y
# CONFIG_VGA_CONSOLE is not set
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_DEVICE_CLASS is not set
CONFIG_USB_MON=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_M66592=y
CONFIG_USB_FILE_STORAGE=m
CONFIG_MMC=y
CONFIG_MMC_DEBUG=y
# CONFIG_MMC_BLOCK_BOUNCE is not set
CONFIG_MMC_AT91=m
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
CONFIG_LEDS_GPIO=y
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_AT91RM9200=y
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT3_FS=y
CONFIG_REISERFS_FS=y
CONFIG_INOTIFY=y
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_TMPFS=y
CONFIG_JFFS2_FS=y
CONFIG_JFFS2_FS_DEBUG=1
CONFIG_JFFS2_COMPRESSION_OPTIONS=y
CONFIG_JFFS2_RUBIN=y
CONFIG_CRAMFS=y
CONFIG_PARTITION_ADVANCED=y
CONFIG_MAC_PARTITION=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_DEBUG_FS=y
CONFIG_DEBUG_KERNEL=y
CONFIG_SLUB_DEBUG_ON=y
CONFIG_DEBUG_KOBJECT=y
CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_LIST=y
CONFIG_DEBUG_USER=y
CONFIG_DEBUG_ERRORS=y
CONFIG_DEBUG_LL=y
arch/arm/kernel/entry-armv.S
浏览文件 @ 67b738ef
......@@ -911,7 +911,7 @@ __kuser_cmpxchg: @ 0xffff0fc0
* A special ghost syscall is used for that (see traps.c).
*/
stmfd sp!, {r7, lr}
ldr r7, =1f @ it's 20 bits
ldr r7, 1f @ it's 20 bits
swi __ARM_NR_cmpxchg
ldmfd sp!, {r7, pc}
1: .word __ARM_NR_cmpxchg
......
arch/arm/kernel/head.S
浏览文件 @ 67b738ef
......@@ -85,9 +85,11 @@ ENTRY(stext)
mrc p15, 0, r9, c0, c0 @ get processor id
bl __lookup_processor_type @ r5=procinfo r9=cpuid
movs r10, r5 @ invalid processor (r5=0)?
THUMB( it eq ) @ force fixup-able long branch encoding
beq __error_p @ yes, error 'p'
bl __lookup_machine_type @ r5=machinfo
movs r8, r5 @ invalid machine (r5=0)?
THUMB( it eq ) @ force fixup-able long branch encoding
beq __error_a @ yes, error 'a'
bl __vet_atags
#ifdef CONFIG_SMP_ON_UP
......@@ -262,6 +264,7 @@ __create_page_tables:
mov pc, lr
ENDPROC(__create_page_tables)
.ltorg
.align
__enable_mmu_loc:
.long .
.long __enable_mmu
......@@ -282,6 +285,7 @@ ENTRY(secondary_startup)
bl __lookup_processor_type
movs r10, r5 @ invalid processor?
moveq r0, #'p' @ yes, error 'p'
THUMB( it eq ) @ force fixup-able long branch encoding
beq __error_p
/*
......@@ -308,6 +312,8 @@ ENTRY(__secondary_switched)
b secondary_start_kernel
ENDPROC(__secondary_switched)
.align
.type __secondary_data, %object
__secondary_data:
.long .
......@@ -413,6 +419,7 @@ __fixup_smp_on_up:
mov pc, lr
ENDPROC(__fixup_smp)
.align
1: .word .
.word __smpalt_begin
.word __smpalt_end
......
arch/arm/kernel/relocate_kernel.S
浏览文件 @ 67b738ef
......@@ -59,6 +59,8 @@ relocate_new_kernel:
ldr r2,kexec_boot_atags
mov pc,lr
.align
.globl kexec_start_address
kexec_start_address:
.long 0x0
......
arch/arm/mach-at91/Makefile
浏览文件 @ 67b738ef
......@@ -24,8 +24,8 @@ obj-$(CONFIG_ARCH_AT91X40) += at91x40.o at91x40_time.o
# AT91RM9200 board-specific support
obj-$(CONFIG_MACH_ONEARM) += board-1arm.o
obj-$(CONFIG_ARCH_AT91RM9200DK) += board-dk.o
obj-$(CONFIG_MACH_AT91RM9200EK) += board-ek.o
obj-$(CONFIG_ARCH_AT91RM9200DK) += board-rm9200dk.o
obj-$(CONFIG_MACH_AT91RM9200EK) += board-rm9200ek.o
obj-$(CONFIG_MACH_CSB337) += board-csb337.o
obj-$(CONFIG_MACH_CSB637) += board-csb637.o
obj-$(CONFIG_MACH_CARMEVA) += board-carmeva.o
......
arch/arm/mach-at91/at91rm9200_devices.c
浏览文件 @ 67b738ef
......@@ -1106,51 +1106,6 @@ static inline void configure_usart3_pins(unsigned pins)
static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
struct platform_device *atmel_default_console_device; /* the serial console device */
void __init __deprecated at91_init_serial(struct at91_uart_config *config)
{
int i;
/* Fill in list of supported UARTs */
for (i = 0; i < config->nr_tty; i++) {
switch (config->tty_map[i]) {
case 0:
configure_usart0_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_uarts[i] = &at91rm9200_uart0_device;
at91_clock_associate("usart0_clk", &at91rm9200_uart0_device.dev, "usart");
break;
case 1:
configure_usart1_pins(ATMEL_UART_CTS | ATMEL_UART_RTS | ATMEL_UART_DSR | ATMEL_UART_DTR | ATMEL_UART_DCD | ATMEL_UART_RI);
at91_uarts[i] = &at91rm9200_uart1_device;
at91_clock_associate("usart1_clk", &at91rm9200_uart1_device.dev, "usart");
break;
case 2:
configure_usart2_pins(0);
at91_uarts[i] = &at91rm9200_uart2_device;
at91_clock_associate("usart2_clk", &at91rm9200_uart2_device.dev, "usart");
break;
case 3:
configure_usart3_pins(0);
at91_uarts[i] = &at91rm9200_uart3_device;
at91_clock_associate("usart3_clk", &at91rm9200_uart3_device.dev, "usart");
break;
case 4:
configure_dbgu_pins();
at91_uarts[i] = &at91rm9200_dbgu_device;
at91_clock_associate("mck", &at91rm9200_dbgu_device.dev, "usart");
break;
default:
continue;
}
at91_uarts[i]->id = i; /* update ID number to mapped ID */
}
/* Set serial console device */
if (config->console_tty < ATMEL_MAX_UART)
atmel_default_console_device = at91_uarts[config->console_tty];
if (!atmel_default_console_device)
printk(KERN_INFO "AT91: No default serial console defined.\n");
}
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
{
struct platform_device *pdev;
......
arch/arm/mach-at91/board-1arm.c
浏览文件 @ 67b738ef
......@@ -39,24 +39,24 @@
#include "generic.h"
/*
* Serial port configuration.
* 0 .. 3 = USART0 .. USART3
* 4 = DBGU
*/
static struct at91_uart_config __initdata onearm_uart_config = {
.console_tty = 0, /* ttyS0 */
.nr_tty = 3,
.tty_map = { 4, 0, 1, -1, -1 }, /* ttyS0, ..., ttyS4 */
};
static void __init onearm_map_io(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91rm9200_initialize(18432000, AT91RM9200_PQFP);
/* Setup the serial ports and console */
at91_init_serial(&onearm_uart_config);
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
/* USART1 on ttyS2 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
| ATMEL_UART_RI);
/* set serial console to ttyS0 (ie, DBGU) */
at91_set_serial_console(0);
}
static void __init onearm_init_irq(void)
......
arch/arm/mach-at91/board-kafa.c
浏览文件 @ 67b738ef
......@@ -39,17 +39,6 @@
#include "generic.h"
/*
* Serial port configuration.
* 0 .. 3 = USART0 .. USART3
* 4 = DBGU
*/
static struct at91_uart_config __initdata kafa_uart_config = {
.console_tty = 0, /* ttyS0 */
.nr_tty = 2,
.tty_map = { 4, 0, -1, -1, -1 } /* ttyS0, ..., ttyS4 */
};
static void __init kafa_map_io(void)
{
/* Initialize processor: 18.432 MHz crystal */
......@@ -58,8 +47,14 @@ static void __init kafa_map_io(void)
/* Set up the LEDs */
at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4);
/* Setup the serial ports and console */
at91_init_serial(&kafa_uart_config);
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */
at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
/* set serial console to ttyS0 (ie, DBGU) */
at91_set_serial_console(0);
}
static void __init kafa_init_irq(void)
......
arch/arm/mach-at91/board-picotux200.c
浏览文件 @ 67b738ef
......@@ -43,24 +43,21 @@
#include "generic.h"
/*
* Serial port configuration.
* 0 .. 3 = USART0 .. USART3
* 4 = DBGU
*/
static struct at91_uart_config __initdata picotux200_uart_config = {
.console_tty = 0, /* ttyS0 */
.nr_tty = 2,
.tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */
};
static void __init picotux200_map_io(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91rm9200_initialize(18432000, AT91RM9200_BGA);
/* Setup the serial ports and console */
at91_init_serial(&picotux200_uart_config);
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
| ATMEL_UART_RI);
/* set serial console to ttyS0 (ie, DBGU) */
at91_set_serial_console(0);
}
static void __init picotux200_init_irq(void)
......@@ -77,11 +74,6 @@ static struct at91_usbh_data __initdata picotux200_usbh_data = {
.ports = 1,
};
// static struct at91_udc_data __initdata picotux200_udc_data = {
// .vbus_pin = AT91_PIN_PD4,
// .pullup_pin = AT91_PIN_PD5,
// };
static struct at91_mmc_data __initdata picotux200_mmc_data = {
.det_pin = AT91_PIN_PB27,
.slot_b = 0,
......@@ -89,21 +81,6 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = {
.wp_pin = AT91_PIN_PA17,
};
// static struct spi_board_info picotux200_spi_devices[] = {
// { /* DataFlash chip */
// .modalias = "mtd_dataflash",
// .chip_select = 0,
// .max_speed_hz = 15 * 1000 * 1000,
// },
// #ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
// { /* DataFlash card */
// .modalias = "mtd_dataflash",
// .chip_select = 3,
// .max_speed_hz = 15 * 1000 * 1000,
// },
// #endif
// };
#define PICOTUX200_FLASH_BASE AT91_CHIPSELECT_0
#define PICOTUX200_FLASH_SIZE SZ_4M
......@@ -135,21 +112,11 @@ static void __init picotux200_board_init(void)
at91_add_device_eth(&picotux200_eth_data);
/* USB Host */
at91_add_device_usbh(&picotux200_usbh_data);
/* USB Device */
// at91_add_device_udc(&picotux200_udc_data);
// at91_set_multi_drive(picotux200_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */
/* I2C */
at91_add_device_i2c(NULL, 0);
/* SPI */
// at91_add_device_spi(picotux200_spi_devices, ARRAY_SIZE(picotux200_spi_devices));
#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
/* DataFlash card */
at91_set_gpio_output(AT91_PIN_PB22, 0);
#else
/* MMC */
at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
at91_add_device_mmc(0, &picotux200_mmc_data);
#endif
/* NOR Flash */
platform_device_register(&picotux200_flash);
}
......
arch/arm/mach-at91/board-dk.c → arch/arm/mach-at91/board-rm9200dk.c
浏览文件 @ 67b738ef
/*
* linux/arch/arm/mach-at91/board-dk.c
* linux/arch/arm/mach-at91/board-rm9200dk.c
*
* Copyright (C) 2005 SAN People
*
......@@ -91,10 +91,12 @@ static struct at91_cf_data __initdata dk_cf_data = {
// .vcc_pin = ... always powered
};
#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
static struct at91_mmc_data __initdata dk_mmc_data = {
.slot_b = 0,
.wire4 = 1,
};
#endif
static struct spi_board_info dk_spi_devices[] = {
{ /* DataFlash chip */
......
arch/arm/mach-at91/board-ek.c → arch/arm/mach-at91/board-rm9200ek.c
浏览文件 @ 67b738ef
/*
* linux/arch/arm/mach-at91/board-ek.c
* linux/arch/arm/mach-at91/board-rm9200ek.c
*
* Copyright (C) 2005 SAN People
*
......@@ -84,12 +84,14 @@ static struct at91_udc_data __initdata ek_udc_data = {
.pullup_pin = AT91_PIN_PD5,
};
#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
static struct at91_mmc_data __initdata ek_mmc_data = {
.det_pin = AT91_PIN_PB27,
.slot_b = 0,
.wire4 = 1,
.wp_pin = AT91_PIN_PA17,
};
#endif
static struct spi_board_info ek_spi_devices[] = {
{ /* DataFlash chip */
......
arch/arm/mach-at91/board-yl-9200.c
浏览文件 @ 67b738ef
......@@ -387,7 +387,7 @@ static struct spi_board_info yl9200_spi_devices[] = {
* EPSON S1D13806 FB (discontinued chip)
* EPSON S1D13506 FB
*/
#if defined(CONFIG_FB_S1D135XX) || defined(CONFIG_FB_S1D13XXX_MODULE)
#if defined(CONFIG_FB_S1D13XXX) || defined(CONFIG_FB_S1D13XXX_MODULE)
#include <video/s1d13xxxfb.h>
......
arch/arm/mach-at91/include/mach/board.h
浏览文件 @ 67b738ef
......@@ -137,13 +137,7 @@ extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_de
extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins);
extern void __init at91_set_serial_console(unsigned portnr);
struct at91_uart_config {
unsigned short console_tty; /* tty number of serial console */
unsigned short nr_tty; /* number of serial tty's */
short tty_map[]; /* map UART to tty number */
};
extern struct platform_device *atmel_default_console_device;
extern void __init __deprecated at91_init_serial(struct at91_uart_config *config);
struct atmel_uart_data {
short use_dma_tx; /* use transmit DMA? */
......
arch/arm/mach-cns3xxx/pcie.c
浏览文件 @ 67b738ef
......@@ -369,7 +369,7 @@ static int __init cns3xxx_pcie_init(void)
{
int i;
hook_fault_code(16 + 6, cns3xxx_pcie_abort_handler, SIGBUS,
hook_fault_code(16 + 6, cns3xxx_pcie_abort_handler, SIGBUS, 0,
"imprecise external abort");
for (i = 0; i < ARRAY_SIZE(cns3xxx_pcie); i++) {
......
arch/arm/mach-omap1/include/mach/entry-macro.S
浏览文件 @ 67b738ef
......@@ -14,18 +14,17 @@
#include <mach/irqs.h>
#include <asm/hardware/gic.h>
#if (defined(CONFIG_ARCH_OMAP730)||defined(CONFIG_ARCH_OMAP850)) && \
(defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX))
#error "FIXME: OMAP7XX doesn't support multiple-OMAP"
#elif defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
#define INT_IH2_IRQ INT_7XX_IH2_IRQ
#elif defined(CONFIG_ARCH_OMAP15XX)
#define INT_IH2_IRQ INT_1510_IH2_IRQ
#elif defined(CONFIG_ARCH_OMAP16XX)
#define INT_IH2_IRQ INT_1610_IH2_IRQ
#else
#warning "IH2 IRQ defaulted"
#define INT_IH2_IRQ INT_1510_IH2_IRQ
/*
* We use __glue to avoid errors with multiple definitions of
* .globl omap_irq_flags as it's included from entry-armv.S but not
* from entry-common.S.
*/
#ifdef __glue
.pushsection .data
.globl omap_irq_flags
omap_irq_flags:
.word 0
.popsection
#endif
.macro disable_fiq
......@@ -47,9 +46,11 @@
beq 1510f
ldr \irqnr, [\base, #IRQ_SIR_FIQ_REG_OFFSET]
ldr \tmp, =omap_irq_flags @ irq flags address
ldr \tmp, [\tmp, #0] @ irq flags value
cmp \irqnr, #0
ldreq \irqnr, [\base, #IRQ_SIR_IRQ_REG_OFFSET]
cmpeq \irqnr, #INT_IH2_IRQ
cmpeq \irqnr, \tmp
ldreq \base, =OMAP1_IO_ADDRESS(OMAP_IH2_BASE)
ldreq \irqnr, [\base, #IRQ_SIR_IRQ_REG_OFFSET]
addeqs \irqnr, \irqnr, #32
......
arch/arm/mach-omap1/irq.c
浏览文件 @ 67b738ef
......@@ -176,26 +176,31 @@ static struct irq_chip omap_irq_chip = {
void __init omap_init_irq(void)
{
extern unsigned int omap_irq_flags;
int i, j;
#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
if (cpu_is_omap7xx()) {
omap_irq_flags = INT_7XX_IH2_IRQ;
irq_banks = omap7xx_irq_banks;
irq_bank_count = ARRAY_SIZE(omap7xx_irq_banks);
}
#endif
#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
omap_irq_flags = INT_1510_IH2_IRQ;
irq_banks = omap1510_irq_banks;
irq_bank_count = ARRAY_SIZE(omap1510_irq_banks);
}
if (cpu_is_omap310()) {
omap_irq_flags = INT_1510_IH2_IRQ;
irq_banks = omap310_irq_banks;
irq_bank_count = ARRAY_SIZE(omap310_irq_banks);
}
#endif
#if defined(CONFIG_ARCH_OMAP16XX)
if (cpu_is_omap16xx()) {
omap_irq_flags = INT_1510_IH2_IRQ;
irq_banks = omap1610_irq_banks;
irq_bank_count = ARRAY_SIZE(omap1610_irq_banks);
}
......
arch/arm/mach-omap2/include/mach/entry-macro.S
浏览文件 @ 67b738ef
......@@ -38,41 +38,27 @@
*/
#ifdef MULTI_OMAP2
/*
* We use __glue to avoid errors with multiple definitions of
* .globl omap_irq_base as it's included from entry-armv.S but not
* from entry-common.S.
*/
#ifdef __glue
.pushsection .data
omap_irq_base: .word 0
.globl omap_irq_base
omap_irq_base:
.word 0
.popsection
#endif
/* Configure the interrupt base on the first interrupt */
/*
* Configure the interrupt base on the first interrupt.
* See also omap_irq_base_init for setting omap_irq_base.
*/
.macro get_irqnr_preamble, base, tmp
9:
ldr \base, =omap_irq_base @ irq base address
ldr \base, [\base, #0] @ irq base value
cmp \base, #0 @ already configured?
bne 9997f @ nothing to do
mrc p15, 0, \tmp, c0, c0, 0 @ get processor revision
and \tmp, \tmp, #0x000f0000 @ only check architecture
cmp \tmp, #0x00070000 @ is v6?
beq 2400f @ found v6 so it's omap24xx
mrc p15, 0, \tmp, c0, c0, 0 @ get processor revision
and \tmp, \tmp, #0x000000f0 @ check cortex 8 or 9
cmp \tmp, #0x00000080 @ cortex A-8?
beq 3400f @ found A-8 so it's omap34xx
cmp \tmp, #0x00000090 @ cortex A-9?
beq 4400f @ found A-9 so it's omap44xx
2400: ldr \base, =OMAP2_IRQ_BASE
ldr \tmp, =omap_irq_base
str \base, [\tmp, #0]
b 9b
3400: ldr \base, =OMAP3_IRQ_BASE
ldr \tmp, =omap_irq_base
str \base, [\tmp, #0]
b 9b
4400: ldr \base, =OMAP4_IRQ_BASE
ldr \tmp, =omap_irq_base
str \base, [\tmp, #0]
b 9b
9997:
.endm
/* Check the pending interrupts. Note that base already set */
......
arch/arm/mach-omap2/io.c
浏览文件 @ 67b738ef
......@@ -46,6 +46,7 @@
#include "clockdomains.h"
#include <plat/omap_hwmod.h>
#include <plat/multi.h>
/*
* The machine specific code may provide the extra mapping besides the
......@@ -311,6 +312,25 @@ static int __init _omap2_init_reprogram_sdrc(void)
return v;
}
/*
* Initialize asm_irq_base for entry-macro.S
*/
static inline void omap_irq_base_init(void)
{
extern void __iomem *omap_irq_base;
#ifdef MULTI_OMAP2
if (cpu_is_omap242x())
omap_irq_base = OMAP2_L4_IO_ADDRESS(OMAP24XX_IC_BASE);
else if (cpu_is_omap34xx())
omap_irq_base = OMAP2_L4_IO_ADDRESS(OMAP34XX_IC_BASE);
else if (cpu_is_omap44xx())
omap_irq_base = OMAP2_L4_IO_ADDRESS(OMAP44XX_GIC_CPU_BASE);
else
pr_err("Could not initialize omap_irq_base\n");
#endif
}
void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
struct omap_sdrc_params *sdrc_cs1)
{
......@@ -352,4 +372,6 @@ void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
_omap2_init_reprogram_sdrc();
}
gpmc_init();
omap_irq_base_init();
}
arch/arm/mach-realview/headsmp.S
浏览文件 @ 67b738ef
......@@ -35,5 +35,6 @@ pen: ldr r7, [r6]
*/
b secondary_startup
.align
1: .long .
.long pen_release
arch/arm/mach-tegra/include/mach/debug-macro.S
浏览文件 @ 67b738ef
......@@ -21,8 +21,8 @@
#include <mach/io.h>
.macro addruart, rp, rv
ldreq \rp, =IO_APB_PHYS @ physical
ldrne \rv, =IO_APB_VIRT @ virtual
ldr \rp, =IO_APB_PHYS @ physical
ldr \rv, =IO_APB_VIRT @ virtual
#if defined(CONFIG_TEGRA_DEBUG_UART_NONE)
#error "A debug UART must be selected in the kernel config to use DEBUG_LL"
#elif defined(CONFIG_TEGRA_DEBUG_UARTA)
......
arch/arm/mach-vexpress/headsmp.S
浏览文件 @ 67b738ef
......@@ -35,5 +35,6 @@ pen: ldr r7, [r6]
*/
b secondary_startup
.align
1: .long .
.long pen_release
arch/arm/mm/proc-v7.S
浏览文件 @ 67b738ef
......@@ -381,7 +381,7 @@ __v7_ca9mp_proc_info:
PMD_SECT_XN | \
PMD_SECT_AP_WRITE | \
PMD_SECT_AP_READ
b __v7_ca9mp_setup
W(b) __v7_ca9mp_setup
.long cpu_arch_name
.long cpu_elf_name
.long HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP|HWCAP_TLS
......@@ -413,7 +413,7 @@ __v7_proc_info:
PMD_SECT_XN | \
PMD_SECT_AP_WRITE | \
PMD_SECT_AP_READ
b __v7_setup
W(b) __v7_setup
.long cpu_arch_name
.long cpu_elf_name
.long HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP|HWCAP_TLS
......
arch/arm/plat-iop/time.c
浏览文件 @ 67b738ef
......@@ -18,6 +18,7 @@
#include <linux/time.h>
#include <linux/init.h>
#include <linux/timex.h>
#include <linux/sched.h>
#include <linux/io.h>
#include <linux/clocksource.h>
#include <linux/clockchips.h>
......@@ -36,7 +37,7 @@
/*
* IOP clocksource (free-running timer 1).
*/
static cycle_t iop_clocksource_read(struct clocksource *unused)
static cycle_t notrace iop_clocksource_read(struct clocksource *unused)
{
return 0xffffffffu - read_tcr1();
}
......
arch/arm/plat-omap/include/plat/irqs.h
浏览文件 @ 67b738ef
......@@ -77,7 +77,7 @@
/*
* OMAP-1610 specific IRQ numbers for interrupt handler 1
*/
#define INT_1610_IH2_IRQ 0
#define INT_1610_IH2_IRQ INT_1510_IH2_IRQ
#define INT_1610_IH2_FIQ 2
#define INT_1610_McBSP2_TX 4
#define INT_1610_McBSP2_RX 5
......
arch/arm/vfp/vfphw.S
浏览文件 @ 67b738ef
......@@ -206,6 +206,7 @@ ENTRY(vfp_save_state)
mov pc, lr
ENDPROC(vfp_save_state)
.align
last_VFP_context_address:
.word last_VFP_context
......
arch/mn10300/include/asm/syscall.h 0 → 100644
浏览文件 @ 67b738ef
/* Access to user system call parameters and results
*
* See asm-generic/syscall.h for function descriptions.
*
* Copyright (C) 2010 Red Hat, Inc. All Rights Reserved.
* Written by David Howells (dhowells@redhat.com)
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public Licence
* as published by the Free Software Foundation; either version
* 2 of the Licence, or (at your option) any later version.
*/
#ifndef _ASM_SYSCALL_H
#define _ASM_SYSCALL_H
#include <linux/sched.h>
#include <linux/err.h>
extern const unsigned long sys_call_table[];
static inline int syscall_get_nr(struct task_struct *task, struct pt_regs *regs)
{
return regs->orig_d0;
}
static inline void syscall_rollback(struct task_struct *task,
struct pt_regs *regs)
{
regs->d0 = regs->orig_d0;
}
static inline long syscall_get_error(struct task_struct *task,
struct pt_regs *regs)
{
unsigned long error = regs->d0;
return IS_ERR_VALUE(error) ? error : 0;
}
static inline long syscall_get_return_value(struct task_struct *task,
struct pt_regs *regs)
{
return regs->d0;
}
static inline void syscall_set_return_value(struct task_struct *task,
struct pt_regs *regs,
int error, long val)
{
regs->d0 = (long) error ?: val;
}
static inline void syscall_get_arguments(struct task_struct *task,
struct pt_regs *regs,
unsigned int i, unsigned int n,
unsigned long *args)
{
switch (i) {
case 0:
if (!n--) break;
*args++ = regs->a0;
case 1:
if (!n--) break;
*args++ = regs->d1;
case 2:
if (!n--) break;
*args++ = regs->a3;
case 3:
if (!n--) break;
*args++ = regs->a2;
case 4:
if (!n--) break;
*args++ = regs->d3;
case 5:
if (!n--) break;
*args++ = regs->d2;
case 6:
if (!n--) break;
default:
BUG();
break;
}
}
static inline void syscall_set_arguments(struct task_struct *task,
struct pt_regs *regs,
unsigned int i, unsigned int n,
const unsigned long *args)
{
switch (i) {
case 0:
if (!n--) break;
regs->a0 = *args++;
case 1:
if (!n--) break;
regs->d1 = *args++;
case 2:
if (!n--) break;
regs->a3 = *args++;
case 3:
if (!n--) break;
regs->a2 = *args++;
case 4:
if (!n--) break;
regs->d3 = *args++;
case 5:
if (!n--) break;
regs->d2 = *args++;
case 6:
if (!n--) break;
default:
BUG();
break;
}
}
#endif /* _ASM_SYSCALL_H */
arch/parisc/kernel/irq.c
浏览文件 @ 67b738ef
......@@ -75,9 +75,6 @@ static void cpu_unmask_irq(unsigned int irq)
smp_send_all_nop();
}
void no_ack_irq(unsigned int irq) { }
void no_end_irq(unsigned int irq) { }
void cpu_ack_irq(unsigned int irq)
{
unsigned long mask = EIEM_MASK(irq);
......@@ -241,7 +238,7 @@ int cpu_claim_irq(unsigned int irq, struct irq_chip *type, void *data)
/* for iosapic interrupts */
if (type) {
set_irq_chip_and_handler(irq, type, handle_level_irq);
set_irq_chip_and_handler(irq, type, handle_percpu_irq);
set_irq_chip_data(irq, data);
cpu_unmask_irq(irq);
}
......@@ -392,7 +389,7 @@ static void claim_cpu_irqs(void)
int i;
for (i = CPU_IRQ_BASE; i <= CPU_IRQ_MAX; i++) {
set_irq_chip_and_handler(i, &cpu_interrupt_type,
handle_level_irq);
handle_percpu_irq);
}
set_irq_handler(TIMER_IRQ, handle_percpu_irq);
......
arch/parisc/kernel/signal.c
浏览文件 @ 67b738ef
......@@ -98,7 +98,6 @@ void
sys_rt_sigreturn(struct pt_regs *regs, int in_syscall)
{
struct rt_sigframe __user *frame;
struct siginfo si;
sigset_t set;
unsigned long usp = (regs->gr[30] & ~(0x01UL));
unsigned long sigframe_size = PARISC_RT_SIGFRAME_SIZE;
......@@ -178,13 +177,7 @@ sys_rt_sigreturn(struct pt_regs *regs, int in_syscall)
give_sigsegv:
DBG(1,"sys_rt_sigreturn: Sending SIGSEGV\n");
si.si_signo = SIGSEGV;
si.si_errno = 0;
si.si_code = SI_KERNEL;
si.si_pid = task_pid_vnr(current);
si.si_uid = current_uid();
si.si_addr = &frame->uc;
force_sig_info(SIGSEGV, &si, current);
force_sig(SIGSEGV, current);
return;
}
......
arch/sh/boards/mach-ecovec24/setup.c
浏览文件 @ 67b738ef
......@@ -720,32 +720,6 @@ static struct platform_device camera_devices[] = {
};
/* FSI */
/*
* FSI-B use external clock which came from da7210.
* So, we should change parent of fsi
*/
#define FCLKBCR 0xa415000c
static void fsimck_init(struct clk *clk)
{
u32 status = __raw_readl(clk->enable_reg);
/* use external clock */
status &= ~0x000000ff;
status |= 0x00000080;
__raw_writel(status, clk->enable_reg);
}
static struct clk_ops fsimck_clk_ops = {
.init = fsimck_init,
};
static struct clk fsimckb_clk = {
.ops = &fsimck_clk_ops,
.enable_reg = (void __iomem *)FCLKBCR,
.rate = 0, /* unknown */
};
static struct sh_fsi_platform_info fsi_info = {
.portb_flags = SH_FSI_BRS_INV |
SH_FSI_OUT_SLAVE_MODE |
......@@ -1264,10 +1238,10 @@ static int __init arch_setup(void)
/* change parent of FSI B */
clk = clk_get(NULL, "fsib_clk");
if (!IS_ERR(clk)) {
clk_register(&fsimckb_clk);
clk_set_parent(clk, &fsimckb_clk);
clk_set_rate(clk, 11000);
clk_set_rate(&fsimckb_clk, 11000);
/* 48kHz dummy clock was used to make sure 1/1 divide */
clk_set_rate(&sh7724_fsimckb_clk, 48000);
clk_set_parent(clk, &sh7724_fsimckb_clk);
clk_set_rate(clk, 48000);
clk_put(clk);
}
......
arch/sh/boards/mach-se/7724/setup.c
浏览文件 @ 67b738ef
......@@ -283,31 +283,6 @@ static struct platform_device ceu1_device = {
};
/* FSI */
/*
* FSI-A use external clock which came from ak464x.
* So, we should change parent of fsi
*/
#define FCLKACR 0xa4150008
static void fsimck_init(struct clk *clk)
{
u32 status = __raw_readl(clk->enable_reg);
/* use external clock */
status &= ~0x000000ff;
status |= 0x00000080;
__raw_writel(status, clk->enable_reg);
}
static struct clk_ops fsimck_clk_ops = {
.init = fsimck_init,
};
static struct clk fsimcka_clk = {
.ops = &fsimck_clk_ops,
.enable_reg = (void __iomem *)FCLKACR,
.rate = 0, /* unknown */
};
/* change J20, J21, J22 pin to 1-2 connection to use slave mode */
static struct sh_fsi_platform_info fsi_info = {
.porta_flags = SH_FSI_BRS_INV |
......@@ -852,37 +827,29 @@ static int __init devices_setup(void)
gpio_request(GPIO_FN_KEYOUT0, NULL);
/* enable FSI */
gpio_request(GPIO_FN_FSIMCKB, NULL);
gpio_request(GPIO_FN_FSIMCKA, NULL);
gpio_request(GPIO_FN_FSIIASD, NULL);
gpio_request(GPIO_FN_FSIOASD, NULL);
gpio_request(GPIO_FN_FSIIABCK, NULL);
gpio_request(GPIO_FN_FSIIALRCK, NULL);
gpio_request(GPIO_FN_FSIOABCK, NULL);
gpio_request(GPIO_FN_FSIOALRCK, NULL);
gpio_request(GPIO_FN_CLKAUDIOAO, NULL);
gpio_request(GPIO_FN_FSIIBSD, NULL);
gpio_request(GPIO_FN_FSIOBSD, NULL);
gpio_request(GPIO_FN_FSIIBBCK, NULL);
gpio_request(GPIO_FN_FSIIBLRCK, NULL);
gpio_request(GPIO_FN_FSIOBBCK, NULL);
gpio_request(GPIO_FN_FSIOBLRCK, NULL);
gpio_request(GPIO_FN_CLKAUDIOBO, NULL);
gpio_request(GPIO_FN_FSIIASD, NULL);
/* set SPU2 clock to 83.4 MHz */
clk = clk_get(NULL, "spu_clk");
if (clk) {
if (!IS_ERR(clk)) {
clk_set_rate(clk, clk_round_rate(clk, 83333333));
clk_put(clk);
}
/* change parent of FSI A */
clk = clk_get(NULL, "fsia_clk");
if (clk) {
clk_register(&fsimcka_clk);
clk_set_parent(clk, &fsimcka_clk);
clk_set_rate(clk, 11000);
clk_set_rate(&fsimcka_clk, 11000);
if (!IS_ERR(clk)) {
/* 48kHz dummy clock was used to make sure 1/1 divide */
clk_set_rate(&sh7724_fsimcka_clk, 48000);
clk_set_parent(clk, &sh7724_fsimcka_clk);
clk_set_rate(clk, 48000);
clk_put(clk);
}
......
arch/sh/include/asm/cacheflush.h
浏览文件 @ 67b738ef
......@@ -96,7 +96,7 @@ void kmap_coherent_init(void);
void *kmap_coherent(struct page *page, unsigned long addr);
void kunmap_coherent(void *kvaddr);
#define PG_dcache_dirty PG_arch_1
#define PG_dcache_clean PG_arch_1
void cpu_cache_init(void);
......
arch/sh/include/cpu-sh4/cpu/sh7724.h
浏览文件 @ 67b738ef
......@@ -303,4 +303,7 @@ enum {
SHDMA_SLAVE_SDHI1_RX,
};
extern struct clk sh7724_fsimcka_clk;
extern struct clk sh7724_fsimckb_clk;
#endif /* __ASM_SH7724_H__ */
arch/sh/kernel/cpu/sh4a/clock-sh7724.c
浏览文件 @ 67b738ef
......@@ -111,12 +111,21 @@ static struct clk div3_clk = {
.parent = &pll_clk,
};
/* External input clock (pin name: FSIMCKA/FSIMCKB ) */
struct clk sh7724_fsimcka_clk = {
};
struct clk sh7724_fsimckb_clk = {
};
static struct clk *main_clks[] = {
&r_clk,
&extal_clk,
&fll_clk,
&pll_clk,
&div3_clk,
&sh7724_fsimcka_clk,
&sh7724_fsimckb_clk,
};
static void div4_kick(struct clk *clk)
......@@ -154,16 +163,38 @@ struct clk div4_clks[DIV4_NR] = {
[DIV4_M1] = DIV4(FRQCRB, 4, 0x2f7c, CLK_ENABLE_ON_INIT),
};
enum { DIV6_V, DIV6_FA, DIV6_FB, DIV6_I, DIV6_S, DIV6_NR };
enum { DIV6_V, DIV6_I, DIV6_S, DIV6_NR };
static struct clk div6_clks[DIV6_NR] = {
[DIV6_V] = SH_CLK_DIV6(&div3_clk, VCLKCR, 0),
[DIV6_FA] = SH_CLK_DIV6(&div3_clk, FCLKACR, 0),
[DIV6_FB] = SH_CLK_DIV6(&div3_clk, FCLKBCR, 0),
[DIV6_I] = SH_CLK_DIV6(&div3_clk, IRDACLKCR, 0),
[DIV6_S] = SH_CLK_DIV6(&div3_clk, SPUCLKCR, CLK_ENABLE_ON_INIT),
};
enum { DIV6_FA, DIV6_FB, DIV6_REPARENT_NR };
/* Indices are important - they are the actual src selecting values */
static struct clk *fclkacr_parent[] = {
[0] = &div3_clk,
[1] = NULL,
[2] = &sh7724_fsimcka_clk,
[3] = NULL,
};
static struct clk *fclkbcr_parent[] = {
[0] = &div3_clk,
[1] = NULL,
[2] = &sh7724_fsimckb_clk,
[3] = NULL,
};
static struct clk div6_reparent_clks[DIV6_REPARENT_NR] = {
[DIV6_FA] = SH_CLK_DIV6_EXT(&div3_clk, FCLKACR, 0,
fclkacr_parent, ARRAY_SIZE(fclkacr_parent), 6, 2),
[DIV6_FB] = SH_CLK_DIV6_EXT(&div3_clk, FCLKBCR, 0,
fclkbcr_parent, ARRAY_SIZE(fclkbcr_parent), 6, 2),
};
static struct clk mstp_clks[HWBLK_NR] = {
SH_HWBLK_CLK(HWBLK_TLB, &div4_clks[DIV4_I], CLK_ENABLE_ON_INIT),
SH_HWBLK_CLK(HWBLK_IC, &div4_clks[DIV4_I], CLK_ENABLE_ON_INIT),
......@@ -240,8 +271,8 @@ static struct clk_lookup lookups[] = {
/* DIV6 clocks */
CLKDEV_CON_ID("video_clk", &div6_clks[DIV6_V]),
CLKDEV_CON_ID("fsia_clk", &div6_clks[DIV6_FA]),
CLKDEV_CON_ID("fsib_clk", &div6_clks[DIV6_FB]),
CLKDEV_CON_ID("fsia_clk", &div6_reparent_clks[DIV6_FA]),
CLKDEV_CON_ID("fsib_clk", &div6_reparent_clks[DIV6_FB]),
CLKDEV_CON_ID("irda_clk", &div6_clks[DIV6_I]),
CLKDEV_CON_ID("spu_clk", &div6_clks[DIV6_S]),
......@@ -375,6 +406,9 @@ int __init arch_clk_init(void)
if (!ret)
ret = sh_clk_div6_register(div6_clks, DIV6_NR);
if (!ret)
ret = sh_clk_div6_reparent_register(div6_reparent_clks, DIV6_REPARENT_NR);
if (!ret)
ret = sh_hwblk_clk_register(mstp_clks, HWBLK_NR);
......
arch/sh/mm/cache-sh4.c
浏览文件 @ 67b738ef
......@@ -114,7 +114,7 @@ static void sh4_flush_dcache_page(void *arg)
struct address_space *mapping = page_mapping(page);
if (mapping && !mapping_mapped(mapping))
set_bit(PG_dcache_dirty, &page->flags);
clear_bit(PG_dcache_clean, &page->flags);
else
#endif
flush_cache_one(CACHE_OC_ADDRESS_ARRAY |
......@@ -239,7 +239,7 @@ static void sh4_flush_cache_page(void *args)
* another ASID than the current one.
*/
map_coherent = (current_cpu_data.dcache.n_aliases &&
!test_bit(PG_dcache_dirty, &page->flags) &&
test_bit(PG_dcache_clean, &page->flags) &&
page_mapped(page));
if (map_coherent)
vaddr = kmap_coherent(page, address);
......
arch/sh/mm/cache-sh7705.c
浏览文件 @ 67b738ef
......@@ -139,7 +139,7 @@ static void sh7705_flush_dcache_page(void *arg)
struct address_space *mapping = page_mapping(page);
if (mapping && !mapping_mapped(mapping))
set_bit(PG_dcache_dirty, &page->flags);
clear_bit(PG_dcache_clean, &page->flags);
else
__flush_dcache_page(__pa(page_address(page)));
}
......
arch/sh/mm/cache.c
浏览文件 @ 67b738ef
......@@ -60,14 +60,14 @@ void copy_to_user_page(struct vm_area_struct *vma, struct page *page,
unsigned long len)
{
if (boot_cpu_data.dcache.n_aliases && page_mapped(page) &&
!test_bit(PG_dcache_dirty, &page->flags)) {
test_bit(PG_dcache_clean, &page->flags)) {
void *vto = kmap_coherent(page, vaddr) + (vaddr & ~PAGE_MASK);
memcpy(vto, src, len);
kunmap_coherent(vto);
} else {
memcpy(dst, src, len);
if (boot_cpu_data.dcache.n_aliases)
set_bit(PG_dcache_dirty, &page->flags);
clear_bit(PG_dcache_clean, &page->flags);
}
if (vma->vm_flags & VM_EXEC)
......@@ -79,14 +79,14 @@ void copy_from_user_page(struct vm_area_struct *vma, struct page *page,
unsigned long len)
{
if (boot_cpu_data.dcache.n_aliases && page_mapped(page) &&
!test_bit(PG_dcache_dirty, &page->flags)) {
test_bit(PG_dcache_clean, &page->flags)) {
void *vfrom = kmap_coherent(page, vaddr) + (vaddr & ~PAGE_MASK);
memcpy(dst, vfrom, len);
kunmap_coherent(vfrom);
} else {
memcpy(dst, src, len);
if (boot_cpu_data.dcache.n_aliases)
set_bit(PG_dcache_dirty, &page->flags);
clear_bit(PG_dcache_clean, &page->flags);
}
}
......@@ -98,7 +98,7 @@ void copy_user_highpage(struct page *to, struct page *from,
vto = kmap_atomic(to, KM_USER1);
if (boot_cpu_data.dcache.n_aliases && page_mapped(from) &&
!test_bit(PG_dcache_dirty, &from->flags)) {
test_bit(PG_dcache_clean, &from->flags)) {
vfrom = kmap_coherent(from, vaddr);
copy_page(vto, vfrom);
kunmap_coherent(vfrom);
......@@ -141,7 +141,7 @@ void __update_cache(struct vm_area_struct *vma,
page = pfn_to_page(pfn);
if (pfn_valid(pfn)) {
int dirty = test_and_clear_bit(PG_dcache_dirty, &page->flags);
int dirty = !test_and_set_bit(PG_dcache_clean, &page->flags);
if (dirty)
__flush_purge_region(page_address(page), PAGE_SIZE);
}
......@@ -153,7 +153,7 @@ void __flush_anon_page(struct page *page, unsigned long vmaddr)
if (pages_do_alias(addr, vmaddr)) {
if (boot_cpu_data.dcache.n_aliases && page_mapped(page) &&
!test_bit(PG_dcache_dirty, &page->flags)) {
test_bit(PG_dcache_clean, &page->flags)) {
void *kaddr;
kaddr = kmap_coherent(page, vmaddr);
......
arch/sh/mm/kmap.c
浏览文件 @ 67b738ef
......@@ -34,7 +34,7 @@ void *kmap_coherent(struct page *page, unsigned long addr)
enum fixed_addresses idx;
unsigned long vaddr;
BUG_ON(test_bit(PG_dcache_dirty, &page->flags));
BUG_ON(!test_bit(PG_dcache_clean, &page->flags));
pagefault_disable();
......
arch/x86/pci/xen.c
浏览文件 @ 67b738ef
......@@ -70,6 +70,9 @@ static int acpi_register_gsi_xen_hvm(struct device *dev, u32 gsi,
struct xen_pci_frontend_ops *xen_pci_frontend;
EXPORT_SYMBOL_GPL(xen_pci_frontend);
#define XEN_PIRQ_MSI_DATA (MSI_DATA_TRIGGER_EDGE | \
MSI_DATA_LEVEL_ASSERT | (3 << 8) | MSI_DATA_VECTOR(0))
static void xen_msi_compose_msg(struct pci_dev *pdev, unsigned int pirq,
struct msi_msg *msg)
{
......@@ -83,12 +86,7 @@ static void xen_msi_compose_msg(struct pci_dev *pdev, unsigned int pirq,
MSI_ADDR_REDIRECTION_CPU |
MSI_ADDR_DEST_ID(pirq);
msg->data =
MSI_DATA_TRIGGER_EDGE |
MSI_DATA_LEVEL_ASSERT |
/* delivery mode reserved */
(3 << 8) |
MSI_DATA_VECTOR(0);
msg->data = XEN_PIRQ_MSI_DATA;
}
static int xen_hvm_setup_msi_irqs(struct pci_dev *dev, int nvec, int type)
......@@ -98,8 +96,23 @@ static int xen_hvm_setup_msi_irqs(struct pci_dev *dev, int nvec, int type)
struct msi_msg msg;
list_for_each_entry(msidesc, &dev->msi_list, list) {
__read_msi_msg(msidesc, &msg);
pirq = MSI_ADDR_EXT_DEST_ID(msg.address_hi) |
((msg.address_lo >> MSI_ADDR_DEST_ID_SHIFT) & 0xff);
if (xen_irq_from_pirq(pirq) >= 0 && msg.data == XEN_PIRQ_MSI_DATA) {
xen_allocate_pirq_msi((type == PCI_CAP_ID_MSIX) ?
"msi-x" : "msi", &irq, &pirq, XEN_ALLOC_IRQ);
if (irq < 0)
goto error;
ret = set_irq_msi(irq, msidesc);
if (ret < 0)
goto error_while;
printk(KERN_DEBUG "xen: msi already setup: msi --> irq=%d"
" pirq=%d\n", irq, pirq);
return 0;
}
xen_allocate_pirq_msi((type == PCI_CAP_ID_MSIX) ?
"msi-x" : "msi", &irq, &pirq);
"msi-x" : "msi", &irq, &pirq, (XEN_ALLOC_IRQ | XEN_ALLOC_PIRQ));
if (irq < 0 || pirq < 0)
goto error;
printk(KERN_DEBUG "xen: msi --> irq=%d, pirq=%d\n", irq, pirq);
......
arch/x86/xen/enlighten.c
浏览文件 @ 67b738ef
......@@ -1021,10 +1021,6 @@ static void xen_reboot(int reason)
{
struct sched_shutdown r = { .reason = reason };
#ifdef CONFIG_SMP
stop_other_cpus();
#endif
if (HYPERVISOR_sched_op(SCHEDOP_shutdown, &r))
BUG();
}
......
arch/x86/xen/mmu.c
浏览文件 @ 67b738ef
......@@ -2415,8 +2415,6 @@ void __init xen_init_mmu_ops(void)
x86_init.paging.pagetable_setup_done = xen_pagetable_setup_done;
pv_mmu_ops = xen_mmu_ops;
vmap_lazy_unmap = false;
memset(dummy_mapping, 0xff, PAGE_SIZE);
}
......
arch/x86/xen/platform-pci-unplug.c
浏览文件 @ 67b738ef
......@@ -68,7 +68,7 @@ static int __init check_platform_magic(void)
return 0;
}
void __init xen_unplug_emulated_devices(void)
void xen_unplug_emulated_devices(void)
{
int r;
......
arch/x86/xen/setup.c
浏览文件 @ 67b738ef
......@@ -181,24 +181,21 @@ char * __init xen_memory_setup(void)
for (i = 0; i < memmap.nr_entries; i++) {
unsigned long long end = map[i].addr + map[i].size;
if (map[i].type == E820_RAM) {
if (map[i].addr < mem_end && end > mem_end) {
/* Truncate region to max_mem. */
u64 delta = end - mem_end;
if (map[i].type == E820_RAM && end > mem_end) {
/* RAM off the end - may be partially included */
u64 delta = min(map[i].size, end - mem_end);
map[i].size -= delta;
extra_pages += PFN_DOWN(delta);
map[i].size -= delta;
end -= delta;
end = mem_end;
}
extra_pages += PFN_DOWN(delta);
}
if (end > xen_extra_mem_start)
if (map[i].size > 0 && end > xen_extra_mem_start)
xen_extra_mem_start = end;
/* If region is non-RAM or below mem_end, add what remains */
if ((map[i].type != E820_RAM || map[i].addr < mem_end) &&
map[i].size > 0)
/* Add region if any remains */
if (map[i].size > 0)
e820_add_region(map[i].addr, map[i].size, map[i].type);
}
......@@ -252,20 +249,6 @@ char * __init xen_memory_setup(void)
return "Xen";
}
static void xen_idle(void)
{
local_irq_disable();
if (need_resched())
local_irq_enable();
else {
current_thread_info()->status &= ~TS_POLLING;
smp_mb__after_clear_bit();
safe_halt();
current_thread_info()->status |= TS_POLLING;
}
}
/*
* Set the bit indicating "nosegneg" library variants should be used.
* We only need to bother in pure 32-bit mode; compat 32-bit processes
......@@ -362,7 +345,11 @@ void __init xen_arch_setup(void)
MAX_GUEST_CMDLINE > COMMAND_LINE_SIZE ?
COMMAND_LINE_SIZE : MAX_GUEST_CMDLINE);
pm_idle = xen_idle;
/* Set up idle, making sure it calls safe_halt() pvop */
#ifdef CONFIG_X86_32
boot_cpu_data.hlt_works_ok = 1;
#endif
pm_idle = default_idle;
fiddle_vdso();
}
arch/x86/xen/suspend.c
浏览文件 @ 67b738ef
......@@ -31,6 +31,7 @@ void xen_hvm_post_suspend(int suspend_cancelled)
int cpu;
xen_hvm_init_shared_info();
xen_callback_vector();
xen_unplug_emulated_devices();
if (xen_feature(XENFEAT_hvm_safe_pvclock)) {
for_each_online_cpu(cpu) {
xen_setup_runstate_info(cpu);
......
arch/x86/xen/xen-ops.h
浏览文件 @ 67b738ef
......@@ -43,7 +43,7 @@ void xen_vcpu_restore(void);
void xen_callback_vector(void);
void xen_hvm_init_shared_info(void);
void __init xen_unplug_emulated_devices(void);
void xen_unplug_emulated_devices(void);
void __init xen_build_dynamic_phys_to_machine(void);
......
drivers/block/rbd.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/dma/shdma.c
浏览文件 @ 67b738ef
......@@ -1213,3 +1213,4 @@ module_exit(sh_dmae_exit);
MODULE_AUTHOR("Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>");
MODULE_DESCRIPTION("Renesas SH DMA Engine driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:sh-dma-engine");
drivers/gpio/cs5535-gpio.c
浏览文件 @ 67b738ef
......@@ -56,6 +56,18 @@ static struct cs5535_gpio_chip {
* registers, see include/linux/cs5535.h.
*/
static void errata_outl(u32 val, unsigned long addr)
{
/*
* According to the CS5536 errata (#36), after suspend
* a write to the high bank GPIO register will clear all
* non-selected bits; the recommended workaround is a
* read-modify-write operation.
*/
val |= inl(addr);
outl(val, addr);
}
static void __cs5535_gpio_set(struct cs5535_gpio_chip *chip, unsigned offset,
unsigned int reg)
{
......@@ -64,7 +76,7 @@ static void __cs5535_gpio_set(struct cs5535_gpio_chip *chip, unsigned offset,
outl(1 << offset, chip->base + reg);
else
/* high bank register */
outl(1 << (offset - 16), chip->base + 0x80 + reg);
errata_outl(1 << (offset - 16), chip->base + 0x80 + reg);
}
void cs5535_gpio_set(unsigned offset, unsigned int reg)
......@@ -86,7 +98,7 @@ static void __cs5535_gpio_clear(struct cs5535_gpio_chip *chip, unsigned offset,
outl(1 << (offset + 16), chip->base + reg);
else
/* high bank register */
outl(1 << offset, chip->base + 0x80 + reg);
errata_outl(1 << offset, chip->base + 0x80 + reg);
}
void cs5535_gpio_clear(unsigned offset, unsigned int reg)
......
drivers/gpu/drm/drm_crtc_helper.c
浏览文件 @ 67b738ef
......@@ -471,6 +471,7 @@ int drm_crtc_helper_set_config(struct drm_mode_set *set)
int count = 0, ro, fail = 0;
struct drm_crtc_helper_funcs *crtc_funcs;
int ret = 0;
int i;
DRM_DEBUG_KMS("\n");
......@@ -666,6 +667,12 @@ int drm_crtc_helper_set_config(struct drm_mode_set *set)
if (ret != 0)
goto fail;
}
DRM_DEBUG_KMS("Setting connector DPMS state to on\n");
for (i = 0; i < set->num_connectors; i++) {
DRM_DEBUG_KMS("\t[CONNECTOR:%d:%s] set DPMS on\n", set->connectors[i]->base.id,
drm_get_connector_name(set->connectors[i]));
set->connectors[i]->dpms = DRM_MODE_DPMS_ON;
}
kfree(save_connectors);
kfree(save_encoders);
......@@ -841,7 +848,7 @@ static void output_poll_execute(struct work_struct *work)
struct delayed_work *delayed_work = to_delayed_work(work);
struct drm_device *dev = container_of(delayed_work, struct drm_device, mode_config.output_poll_work);
struct drm_connector *connector;
enum drm_connector_status old_status, status;
enum drm_connector_status old_status;
bool repoll = false, changed = false;
if (!drm_kms_helper_poll)
......@@ -866,8 +873,9 @@ static void output_poll_execute(struct work_struct *work)
!(connector->polled & DRM_CONNECTOR_POLL_HPD))
continue;
status = connector->funcs->detect(connector, false);
if (old_status != status)
connector->status = connector->funcs->detect(connector, false);
DRM_DEBUG_KMS("connector status updated to %d\n", connector->status);
if (old_status != connector->status)
changed = true;
}
......
drivers/gpu/drm/i915/i915_gem.c
浏览文件 @ 67b738ef
......@@ -38,8 +38,7 @@
static uint32_t i915_gem_get_gtt_alignment(struct drm_gem_object *obj);
static int i915_gem_object_flush_gpu_write_domain(struct drm_gem_object *obj,
bool pipelined);
static int i915_gem_object_flush_gpu_write_domain(struct drm_gem_object *obj);
static void i915_gem_object_flush_gtt_write_domain(struct drm_gem_object *obj);
static void i915_gem_object_flush_cpu_write_domain(struct drm_gem_object *obj);
static int i915_gem_object_set_to_cpu_domain(struct drm_gem_object *obj,
......@@ -2594,7 +2593,7 @@ i915_gem_object_put_fence_reg(struct drm_gem_object *obj,
if (reg->gpu) {
int ret;
ret = i915_gem_object_flush_gpu_write_domain(obj, true);
ret = i915_gem_object_flush_gpu_write_domain(obj);
if (ret)
return ret;
......@@ -2742,8 +2741,7 @@ i915_gem_clflush_object(struct drm_gem_object *obj)
/** Flushes any GPU write domain for the object if it's dirty. */
static int
i915_gem_object_flush_gpu_write_domain(struct drm_gem_object *obj,
bool pipelined)
i915_gem_object_flush_gpu_write_domain(struct drm_gem_object *obj)
{
struct drm_device *dev = obj->dev;
uint32_t old_write_domain;
......@@ -2762,10 +2760,7 @@ i915_gem_object_flush_gpu_write_domain(struct drm_gem_object *obj,
obj->read_domains,
old_write_domain);
if (pipelined)
return 0;
return i915_gem_object_wait_rendering(obj, true);
return 0;
}
/** Flushes the GTT write domain for the object if it's dirty. */
......@@ -2826,18 +2821,15 @@ i915_gem_object_set_to_gtt_domain(struct drm_gem_object *obj, int write)
if (obj_priv->gtt_space == NULL)
return -EINVAL;
ret = i915_gem_object_flush_gpu_write_domain(obj, false);
ret = i915_gem_object_flush_gpu_write_domain(obj);
if (ret != 0)
return ret;
ret = i915_gem_object_wait_rendering(obj, true);
if (ret)
return ret;
i915_gem_object_flush_cpu_write_domain(obj);
if (write) {
ret = i915_gem_object_wait_rendering(obj, true);
if (ret)
return ret;
}
old_write_domain = obj->write_domain;
old_read_domains = obj->read_domains;
......@@ -2875,7 +2867,7 @@ i915_gem_object_set_to_display_plane(struct drm_gem_object *obj,
if (obj_priv->gtt_space == NULL)
return -EINVAL;
ret = i915_gem_object_flush_gpu_write_domain(obj, true);
ret = i915_gem_object_flush_gpu_write_domain(obj);
if (ret)
return ret;
......@@ -2924,9 +2916,12 @@ i915_gem_object_set_to_cpu_domain(struct drm_gem_object *obj, int write)
uint32_t old_write_domain, old_read_domains;
int ret;
ret = i915_gem_object_flush_gpu_write_domain(obj, false);
ret = i915_gem_object_flush_gpu_write_domain(obj);
if (ret != 0)
return ret;
ret = i915_gem_object_wait_rendering(obj, true);
if (ret)
return ret;
i915_gem_object_flush_gtt_write_domain(obj);
......@@ -2935,12 +2930,6 @@ i915_gem_object_set_to_cpu_domain(struct drm_gem_object *obj, int write)
*/
i915_gem_object_set_to_full_cpu_read_domain(obj);
if (write) {
ret = i915_gem_object_wait_rendering(obj, true);
if (ret)
return ret;
}
old_write_domain = obj->write_domain;
old_read_domains = obj->read_domains;
......@@ -3205,9 +3194,13 @@ i915_gem_object_set_cpu_read_domain_range(struct drm_gem_object *obj,
if (offset == 0 && size == obj->size)
return i915_gem_object_set_to_cpu_domain(obj, 0);
ret = i915_gem_object_flush_gpu_write_domain(obj, false);
ret = i915_gem_object_flush_gpu_write_domain(obj);
if (ret != 0)
return ret;
ret = i915_gem_object_wait_rendering(obj, true);
if (ret)
return ret;
i915_gem_object_flush_gtt_write_domain(obj);
/* If we're already fully in the CPU read domain, we're done. */
......@@ -3254,192 +3247,230 @@ i915_gem_object_set_cpu_read_domain_range(struct drm_gem_object *obj,
return 0;
}
/**
* Pin an object to the GTT and evaluate the relocations landing in it.
*/
static int
i915_gem_execbuffer_relocate(struct drm_i915_gem_object *obj,
struct drm_file *file_priv,
struct drm_i915_gem_exec_object2 *entry)
i915_gem_execbuffer_relocate_entry(struct drm_i915_gem_object *obj,
struct drm_file *file_priv,
struct drm_i915_gem_exec_object2 *entry,
struct drm_i915_gem_relocation_entry *reloc)
{
struct drm_device *dev = obj->base.dev;
drm_i915_private_t *dev_priv = dev->dev_private;
struct drm_i915_gem_relocation_entry __user *user_relocs;
struct drm_gem_object *target_obj = NULL;
uint32_t target_handle = 0;
int i, ret = 0;
struct drm_gem_object *target_obj;
uint32_t target_offset;
int ret = -EINVAL;
user_relocs = (void __user *)(uintptr_t)entry->relocs_ptr;
for (i = 0; i < entry->relocation_count; i++) {
struct drm_i915_gem_relocation_entry reloc;
uint32_t target_offset;
target_obj = drm_gem_object_lookup(dev, file_priv,
reloc->target_handle);
if (target_obj == NULL)
return -ENOENT;
if (__copy_from_user_inatomic(&reloc,
user_relocs+i,
sizeof(reloc))) {
ret = -EFAULT;
break;
}
target_offset = to_intel_bo(target_obj)->gtt_offset;
if (reloc.target_handle != target_handle) {
drm_gem_object_unreference(target_obj);
#if WATCH_RELOC
DRM_INFO("%s: obj %p offset %08x target %d "
"read %08x write %08x gtt %08x "
"presumed %08x delta %08x\n",
__func__,
obj,
(int) reloc->offset,
(int) reloc->target_handle,
(int) reloc->read_domains,
(int) reloc->write_domain,
(int) target_offset,
(int) reloc->presumed_offset,
reloc->delta);
#endif
target_obj = drm_gem_object_lookup(dev, file_priv,
reloc.target_handle);
if (target_obj == NULL) {
ret = -ENOENT;
break;
}
/* The target buffer should have appeared before us in the
* exec_object list, so it should have a GTT space bound by now.
*/
if (target_offset == 0) {
DRM_ERROR("No GTT space found for object %d\n",
reloc->target_handle);
goto err;
}
target_handle = reloc.target_handle;
}
target_offset = to_intel_bo(target_obj)->gtt_offset;
/* Validate that the target is in a valid r/w GPU domain */
if (reloc->write_domain & (reloc->write_domain - 1)) {
DRM_ERROR("reloc with multiple write domains: "
"obj %p target %d offset %d "
"read %08x write %08x",
obj, reloc->target_handle,
(int) reloc->offset,
reloc->read_domains,
reloc->write_domain);
goto err;
}
if (reloc->write_domain & I915_GEM_DOMAIN_CPU ||
reloc->read_domains & I915_GEM_DOMAIN_CPU) {
DRM_ERROR("reloc with read/write CPU domains: "
"obj %p target %d offset %d "
"read %08x write %08x",
obj, reloc->target_handle,
(int) reloc->offset,
reloc->read_domains,
reloc->write_domain);
goto err;
}
if (reloc->write_domain && target_obj->pending_write_domain &&
reloc->write_domain != target_obj->pending_write_domain) {
DRM_ERROR("Write domain conflict: "
"obj %p target %d offset %d "
"new %08x old %08x\n",
obj, reloc->target_handle,
(int) reloc->offset,
reloc->write_domain,
target_obj->pending_write_domain);
goto err;
}
#if WATCH_RELOC
DRM_INFO("%s: obj %p offset %08x target %d "
"read %08x write %08x gtt %08x "
"presumed %08x delta %08x\n",
__func__,
obj,
(int) reloc.offset,
(int) reloc.target_handle,
(int) reloc.read_domains,
(int) reloc.write_domain,
(int) target_offset,
(int) reloc.presumed_offset,
reloc.delta);
#endif
target_obj->pending_read_domains |= reloc->read_domains;
target_obj->pending_write_domain |= reloc->write_domain;
/* The target buffer should have appeared before us in the
* exec_object list, so it should have a GTT space bound by now.
*/
if (target_offset == 0) {
DRM_ERROR("No GTT space found for object %d\n",
reloc.target_handle);
ret = -EINVAL;
break;
}
/* If the relocation already has the right value in it, no
* more work needs to be done.
*/
if (target_offset == reloc->presumed_offset)
goto out;
/* Validate that the target is in a valid r/w GPU domain */
if (reloc.write_domain & (reloc.write_domain - 1)) {
DRM_ERROR("reloc with multiple write domains: "
"obj %p target %d offset %d "
"read %08x write %08x",
obj, reloc.target_handle,
(int) reloc.offset,
reloc.read_domains,
reloc.write_domain);
ret = -EINVAL;
break;
}
if (reloc.write_domain & I915_GEM_DOMAIN_CPU ||
reloc.read_domains & I915_GEM_DOMAIN_CPU) {
DRM_ERROR("reloc with read/write CPU domains: "
"obj %p target %d offset %d "
"read %08x write %08x",
obj, reloc.target_handle,
(int) reloc.offset,
reloc.read_domains,
reloc.write_domain);
ret = -EINVAL;
break;
}
if (reloc.write_domain && target_obj->pending_write_domain &&
reloc.write_domain != target_obj->pending_write_domain) {
DRM_ERROR("Write domain conflict: "
"obj %p target %d offset %d "
"new %08x old %08x\n",
obj, reloc.target_handle,
(int) reloc.offset,
reloc.write_domain,
target_obj->pending_write_domain);
ret = -EINVAL;
break;
}
/* Check that the relocation address is valid... */
if (reloc->offset > obj->base.size - 4) {
DRM_ERROR("Relocation beyond object bounds: "
"obj %p target %d offset %d size %d.\n",
obj, reloc->target_handle,
(int) reloc->offset,
(int) obj->base.size);
goto err;
}
if (reloc->offset & 3) {
DRM_ERROR("Relocation not 4-byte aligned: "
"obj %p target %d offset %d.\n",
obj, reloc->target_handle,
(int) reloc->offset);
goto err;
}
target_obj->pending_read_domains |= reloc.read_domains;
target_obj->pending_write_domain |= reloc.write_domain;
/* and points to somewhere within the target object. */
if (reloc->delta >= target_obj->size) {
DRM_ERROR("Relocation beyond target object bounds: "
"obj %p target %d delta %d size %d.\n",
obj, reloc->target_handle,
(int) reloc->delta,
(int) target_obj->size);
goto err;
}
/* If the relocation already has the right value in it, no
* more work needs to be done.
*/
if (target_offset == reloc.presumed_offset)
continue;
reloc->delta += target_offset;
if (obj->base.write_domain == I915_GEM_DOMAIN_CPU) {
uint32_t page_offset = reloc->offset & ~PAGE_MASK;
char *vaddr;
/* Check that the relocation address is valid... */
if (reloc.offset > obj->base.size - 4) {
DRM_ERROR("Relocation beyond object bounds: "
"obj %p target %d offset %d size %d.\n",
obj, reloc.target_handle,
(int) reloc.offset, (int) obj->base.size);
ret = -EINVAL;
break;
}
if (reloc.offset & 3) {
DRM_ERROR("Relocation not 4-byte aligned: "
"obj %p target %d offset %d.\n",
obj, reloc.target_handle,
(int) reloc.offset);
ret = -EINVAL;
break;
}
vaddr = kmap_atomic(obj->pages[reloc->offset >> PAGE_SHIFT]);
*(uint32_t *)(vaddr + page_offset) = reloc->delta;
kunmap_atomic(vaddr);
} else {
struct drm_i915_private *dev_priv = dev->dev_private;
uint32_t __iomem *reloc_entry;
void __iomem *reloc_page;
/* and points to somewhere within the target object. */
if (reloc.delta >= target_obj->size) {
DRM_ERROR("Relocation beyond target object bounds: "
"obj %p target %d delta %d size %d.\n",
obj, reloc.target_handle,
(int) reloc.delta, (int) target_obj->size);
ret = -EINVAL;
break;
}
ret = i915_gem_object_set_to_gtt_domain(&obj->base, 1);
if (ret)
goto err;
reloc.delta += target_offset;
if (obj->base.write_domain == I915_GEM_DOMAIN_CPU) {
uint32_t page_offset = reloc.offset & ~PAGE_MASK;
char *vaddr;
/* Map the page containing the relocation we're going to perform. */
reloc->offset += obj->gtt_offset;
reloc_page = io_mapping_map_atomic_wc(dev_priv->mm.gtt_mapping,
reloc->offset & PAGE_MASK);
reloc_entry = (uint32_t __iomem *)
(reloc_page + (reloc->offset & ~PAGE_MASK));
iowrite32(reloc->delta, reloc_entry);
io_mapping_unmap_atomic(reloc_page);
}
vaddr = kmap_atomic(obj->pages[reloc.offset >> PAGE_SHIFT]);
*(uint32_t *)(vaddr + page_offset) = reloc.delta;
kunmap_atomic(vaddr);
} else {
uint32_t __iomem *reloc_entry;
void __iomem *reloc_page;
/* and update the user's relocation entry */
reloc->presumed_offset = target_offset;
ret = i915_gem_object_set_to_gtt_domain(&obj->base, 1);
if (ret)
break;
out:
ret = 0;
err:
drm_gem_object_unreference(target_obj);
return ret;
}
/* Map the page containing the relocation we're going to perform. */
reloc.offset += obj->gtt_offset;
reloc_page = io_mapping_map_atomic_wc(dev_priv->mm.gtt_mapping,
reloc.offset & PAGE_MASK);
reloc_entry = (uint32_t __iomem *)
(reloc_page + (reloc.offset & ~PAGE_MASK));
iowrite32(reloc.delta, reloc_entry);
io_mapping_unmap_atomic(reloc_page);
}
static int
i915_gem_execbuffer_relocate_object(struct drm_i915_gem_object *obj,
struct drm_file *file_priv,
struct drm_i915_gem_exec_object2 *entry)
{
struct drm_i915_gem_relocation_entry __user *user_relocs;
int i, ret;
user_relocs = (void __user *)(uintptr_t)entry->relocs_ptr;
for (i = 0; i < entry->relocation_count; i++) {
struct drm_i915_gem_relocation_entry reloc;
if (__copy_from_user_inatomic(&reloc,
user_relocs+i,
sizeof(reloc)))
return -EFAULT;
ret = i915_gem_execbuffer_relocate_entry(obj, file_priv, entry, &reloc);
if (ret)
return ret;
/* and update the user's relocation entry */
reloc.presumed_offset = target_offset;
if (__copy_to_user_inatomic(&user_relocs[i].presumed_offset,
&reloc.presumed_offset,
sizeof(reloc.presumed_offset))) {
ret = -EFAULT;
break;
}
&reloc.presumed_offset,
sizeof(reloc.presumed_offset)))
return -EFAULT;
}
drm_gem_object_unreference(target_obj);
return ret;
return 0;
}
static int
i915_gem_execbuffer_relocate_object_slow(struct drm_i915_gem_object *obj,
struct drm_file *file_priv,
struct drm_i915_gem_exec_object2 *entry,
struct drm_i915_gem_relocation_entry *relocs)
{
int i, ret;
for (i = 0; i < entry->relocation_count; i++) {
ret = i915_gem_execbuffer_relocate_entry(obj, file_priv, entry, &relocs[i]);
if (ret)
return ret;
}
return 0;
}
static int
i915_gem_execbuffer_pin(struct drm_device *dev,
struct drm_file *file,
struct drm_gem_object **object_list,
struct drm_i915_gem_exec_object2 *exec_list,
int count)
i915_gem_execbuffer_relocate(struct drm_device *dev,
struct drm_file *file,
struct drm_gem_object **object_list,
struct drm_i915_gem_exec_object2 *exec_list,
int count)
{
int i, ret;
for (i = 0; i < count; i++) {
struct drm_i915_gem_object *obj = to_intel_bo(object_list[i]);
obj->base.pending_read_domains = 0;
obj->base.pending_write_domain = 0;
ret = i915_gem_execbuffer_relocate_object(obj, file,
&exec_list[i]);
if (ret)
return ret;
}
return 0;
}
static int
i915_gem_execbuffer_reserve(struct drm_device *dev,
struct drm_file *file,
struct drm_gem_object **object_list,
struct drm_i915_gem_exec_object2 *exec_list,
int count)
{
struct drm_i915_private *dev_priv = dev->dev_private;
int ret, i, retry;
......@@ -3501,6 +3532,87 @@ i915_gem_execbuffer_pin(struct drm_device *dev,
return 0;
}
static int
i915_gem_execbuffer_relocate_slow(struct drm_device *dev,
struct drm_file *file,
struct drm_gem_object **object_list,
struct drm_i915_gem_exec_object2 *exec_list,
int count)
{
struct drm_i915_gem_relocation_entry *reloc;
int i, total, ret;
for (i = 0; i < count; i++) {
struct drm_i915_gem_object *obj = to_intel_bo(object_list[i]);
obj->in_execbuffer = false;
}
mutex_unlock(&dev->struct_mutex);
total = 0;
for (i = 0; i < count; i++)
total += exec_list[i].relocation_count;
reloc = drm_malloc_ab(total, sizeof(*reloc));
if (reloc == NULL) {
mutex_lock(&dev->struct_mutex);
return -ENOMEM;
}
total = 0;
for (i = 0; i < count; i++) {
struct drm_i915_gem_relocation_entry __user *user_relocs;
user_relocs = (void __user *)(uintptr_t)exec_list[i].relocs_ptr;
if (copy_from_user(reloc+total, user_relocs,
exec_list[i].relocation_count *
sizeof(*reloc))) {
ret = -EFAULT;
mutex_lock(&dev->struct_mutex);
goto err;
}
total += exec_list[i].relocation_count;
}
ret = i915_mutex_lock_interruptible(dev);
if (ret) {
mutex_lock(&dev->struct_mutex);
goto err;
}
ret = i915_gem_execbuffer_reserve(dev, file,
object_list, exec_list,
count);
if (ret)
goto err;
total = 0;
for (i = 0; i < count; i++) {
struct drm_i915_gem_object *obj = to_intel_bo(object_list[i]);
obj->base.pending_read_domains = 0;
obj->base.pending_write_domain = 0;
ret = i915_gem_execbuffer_relocate_object_slow(obj, file,
&exec_list[i],
reloc + total);
if (ret)
goto err;
total += exec_list[i].relocation_count;
}
/* Leave the user relocations as are, this is the painfully slow path,
* and we want to avoid the complication of dropping the lock whilst
* having buffers reserved in the aperture and so causing spurious
* ENOSPC for random operations.
*/
err:
drm_free_large(reloc);
return ret;
}
static int
i915_gem_execbuffer_move_to_gpu(struct drm_device *dev,
struct drm_file *file,
......@@ -3630,8 +3742,15 @@ validate_exec_list(struct drm_i915_gem_exec_object2 *exec,
for (i = 0; i < count; i++) {
char __user *ptr = (char __user *)(uintptr_t)exec[i].relocs_ptr;
size_t length = exec[i].relocation_count * sizeof(struct drm_i915_gem_relocation_entry);
int length; /* limited by fault_in_pages_readable() */
/* First check for malicious input causing overflow */
if (exec[i].relocation_count >
INT_MAX / sizeof(struct drm_i915_gem_relocation_entry))
return -EINVAL;
length = exec[i].relocation_count *
sizeof(struct drm_i915_gem_relocation_entry);
if (!access_ok(VERIFY_READ, ptr, length))
return -EFAULT;
......@@ -3774,18 +3893,24 @@ i915_gem_do_execbuffer(struct drm_device *dev, void *data,
}
/* Move the objects en-masse into the GTT, evicting if necessary. */
ret = i915_gem_execbuffer_pin(dev, file,
object_list, exec_list,
args->buffer_count);
ret = i915_gem_execbuffer_reserve(dev, file,
object_list, exec_list,
args->buffer_count);
if (ret)
goto err;
/* The objects are in their final locations, apply the relocations. */
for (i = 0; i < args->buffer_count; i++) {
struct drm_i915_gem_object *obj = to_intel_bo(object_list[i]);
obj->base.pending_read_domains = 0;
obj->base.pending_write_domain = 0;
ret = i915_gem_execbuffer_relocate(obj, file, &exec_list[i]);
ret = i915_gem_execbuffer_relocate(dev, file,
object_list, exec_list,
args->buffer_count);
if (ret) {
if (ret == -EFAULT) {
ret = i915_gem_execbuffer_relocate_slow(dev, file,
object_list,
exec_list,
args->buffer_count);
BUG_ON(!mutex_is_locked(&dev->struct_mutex));
}
if (ret)
goto err;
}
......
drivers/gpu/drm/i915/i915_suspend.c
浏览文件 @ 67b738ef
......@@ -239,6 +239,16 @@ static void i915_save_modeset_reg(struct drm_device *dev)
if (drm_core_check_feature(dev, DRIVER_MODESET))
return;
/* Cursor state */
dev_priv->saveCURACNTR = I915_READ(CURACNTR);
dev_priv->saveCURAPOS = I915_READ(CURAPOS);
dev_priv->saveCURABASE = I915_READ(CURABASE);
dev_priv->saveCURBCNTR = I915_READ(CURBCNTR);
dev_priv->saveCURBPOS = I915_READ(CURBPOS);
dev_priv->saveCURBBASE = I915_READ(CURBBASE);
if (IS_GEN2(dev))
dev_priv->saveCURSIZE = I915_READ(CURSIZE);
if (HAS_PCH_SPLIT(dev)) {
dev_priv->savePCH_DREF_CONTROL = I915_READ(PCH_DREF_CONTROL);
dev_priv->saveDISP_ARB_CTL = I915_READ(DISP_ARB_CTL);
......@@ -529,6 +539,16 @@ static void i915_restore_modeset_reg(struct drm_device *dev)
I915_WRITE(DSPBCNTR, dev_priv->saveDSPBCNTR);
I915_WRITE(DSPBADDR, I915_READ(DSPBADDR));
/* Cursor state */
I915_WRITE(CURAPOS, dev_priv->saveCURAPOS);
I915_WRITE(CURACNTR, dev_priv->saveCURACNTR);
I915_WRITE(CURABASE, dev_priv->saveCURABASE);
I915_WRITE(CURBPOS, dev_priv->saveCURBPOS);
I915_WRITE(CURBCNTR, dev_priv->saveCURBCNTR);
I915_WRITE(CURBBASE, dev_priv->saveCURBBASE);
if (IS_GEN2(dev))
I915_WRITE(CURSIZE, dev_priv->saveCURSIZE);
return;
}
......@@ -543,16 +563,6 @@ void i915_save_display(struct drm_device *dev)
/* Don't save them in KMS mode */
i915_save_modeset_reg(dev);
/* Cursor state */
dev_priv->saveCURACNTR = I915_READ(CURACNTR);
dev_priv->saveCURAPOS = I915_READ(CURAPOS);
dev_priv->saveCURABASE = I915_READ(CURABASE);
dev_priv->saveCURBCNTR = I915_READ(CURBCNTR);
dev_priv->saveCURBPOS = I915_READ(CURBPOS);
dev_priv->saveCURBBASE = I915_READ(CURBBASE);
if (IS_GEN2(dev))
dev_priv->saveCURSIZE = I915_READ(CURSIZE);
/* CRT state */
if (HAS_PCH_SPLIT(dev)) {
dev_priv->saveADPA = I915_READ(PCH_ADPA);
......@@ -657,16 +667,6 @@ void i915_restore_display(struct drm_device *dev)
/* Don't restore them in KMS mode */
i915_restore_modeset_reg(dev);
/* Cursor state */
I915_WRITE(CURAPOS, dev_priv->saveCURAPOS);
I915_WRITE(CURACNTR, dev_priv->saveCURACNTR);
I915_WRITE(CURABASE, dev_priv->saveCURABASE);
I915_WRITE(CURBPOS, dev_priv->saveCURBPOS);
I915_WRITE(CURBCNTR, dev_priv->saveCURBCNTR);
I915_WRITE(CURBBASE, dev_priv->saveCURBBASE);
if (IS_GEN2(dev))
I915_WRITE(CURSIZE, dev_priv->saveCURSIZE);
/* CRT state */
if (HAS_PCH_SPLIT(dev))
I915_WRITE(PCH_ADPA, dev_priv->saveADPA);
......
drivers/gpu/drm/i915/intel_display.c
浏览文件 @ 67b738ef
......@@ -5336,9 +5336,14 @@ static void intel_setup_outputs(struct drm_device *dev)
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_encoder *encoder;
bool dpd_is_edp = false;
bool has_lvds = false;
if (IS_MOBILE(dev) && !IS_I830(dev))
intel_lvds_init(dev);
has_lvds = intel_lvds_init(dev);
if (!has_lvds && !HAS_PCH_SPLIT(dev)) {
/* disable the panel fitter on everything but LVDS */
I915_WRITE(PFIT_CONTROL, 0);
}
if (HAS_PCH_SPLIT(dev)) {
dpd_is_edp = intel_dpd_is_edp(dev);
......
drivers/gpu/drm/i915/intel_dp.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/gpu/drm/i915/intel_drv.h
浏览文件 @ 67b738ef
......@@ -237,7 +237,7 @@ extern bool intel_sdvo_init(struct drm_device *dev, int output_device);
extern void intel_dvo_init(struct drm_device *dev);
extern void intel_tv_init(struct drm_device *dev);
extern void intel_mark_busy(struct drm_device *dev, struct drm_gem_object *obj);
extern void intel_lvds_init(struct drm_device *dev);
extern bool intel_lvds_init(struct drm_device *dev);
extern void intel_dp_init(struct drm_device *dev, int dp_reg);
void
intel_dp_set_m_n(struct drm_crtc *crtc, struct drm_display_mode *mode,
......
drivers/gpu/drm/i915/intel_lvds.c
浏览文件 @ 67b738ef
......@@ -837,7 +837,7 @@ static bool intel_lvds_ddc_probe(struct drm_device *dev, u8 pin)
* Create the connector, register the LVDS DDC bus, and try to figure out what
* modes we can display on the LVDS panel (if present).
*/
void intel_lvds_init(struct drm_device *dev)
bool intel_lvds_init(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_lvds *intel_lvds;
......@@ -853,37 +853,37 @@ void intel_lvds_init(struct drm_device *dev)
/* Skip init on machines we know falsely report LVDS */
if (dmi_check_system(intel_no_lvds))
return;
return false;
pin = GMBUS_PORT_PANEL;
if (!lvds_is_present_in_vbt(dev, &pin)) {
DRM_DEBUG_KMS("LVDS is not present in VBT\n");
return;
return false;
}
if (HAS_PCH_SPLIT(dev)) {
if ((I915_READ(PCH_LVDS) & LVDS_DETECTED) == 0)
return;
return false;
if (dev_priv->edp.support) {
DRM_DEBUG_KMS("disable LVDS for eDP support\n");
return;
return false;
}
}
if (!intel_lvds_ddc_probe(dev, pin)) {
DRM_DEBUG_KMS("LVDS did not respond to DDC probe\n");
return;
return false;
}
intel_lvds = kzalloc(sizeof(struct intel_lvds), GFP_KERNEL);
if (!intel_lvds) {
return;
return false;
}
intel_connector = kzalloc(sizeof(struct intel_connector), GFP_KERNEL);
if (!intel_connector) {
kfree(intel_lvds);
return;
return false;
}
if (!HAS_PCH_SPLIT(dev)) {
......@@ -1026,7 +1026,7 @@ void intel_lvds_init(struct drm_device *dev)
/* keep the LVDS connector */
dev_priv->int_lvds_connector = connector;
drm_sysfs_connector_add(connector);
return;
return true;
failed:
DRM_DEBUG_KMS("No LVDS modes found, disabling.\n");
......@@ -1034,4 +1034,5 @@ void intel_lvds_init(struct drm_device *dev)
drm_encoder_cleanup(encoder);
kfree(intel_lvds);
kfree(intel_connector);
return false;
}
drivers/gpu/drm/i915/intel_sdvo.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/gpu/drm/radeon/atom.c
浏览文件 @ 67b738ef
......@@ -112,6 +112,7 @@ static uint32_t atom_iio_execute(struct atom_context *ctx, int base,
base += 3;
break;
case ATOM_IIO_WRITE:
(void)ctx->card->ioreg_read(ctx->card, CU16(base + 1));
ctx->card->ioreg_write(ctx->card, CU16(base + 1), temp);
base += 3;
break;
......
drivers/gpu/drm/radeon/r600_cs.c
浏览文件 @ 67b738ef
......@@ -315,7 +315,7 @@ static inline int r600_cs_track_validate_cb(struct radeon_cs_parser *p, int i)
if (array_mode == V_0280A0_ARRAY_LINEAR_GENERAL) {
/* the initial DDX does bad things with the CB size occasionally */
/* it rounds up height too far for slice tile max but the BO is smaller */
tmp = (height - 7) * pitch * bpe;
tmp = (height - 7) * 8 * bpe;
if ((tmp + track->cb_color_bo_offset[i]) > radeon_bo_size(track->cb_color_bo[i])) {
dev_warn(p->dev, "%s offset[%d] %d %d %lu too big\n", __func__, i, track->cb_color_bo_offset[i], tmp, radeon_bo_size(track->cb_color_bo[i]));
return -EINVAL;
......
drivers/gpu/drm/radeon/r600_reg.h
浏览文件 @ 67b738ef
......@@ -86,6 +86,7 @@
#define R600_HDP_NONSURFACE_BASE 0x2c04
#define R600_BUS_CNTL 0x5420
# define R600_BIOS_ROM_DIS (1 << 1)
#define R600_CONFIG_CNTL 0x5424
#define R600_CONFIG_MEMSIZE 0x5428
#define R600_CONFIG_F0_BASE 0x542C
......
drivers/gpu/drm/radeon/radeon_atombios.c
浏览文件 @ 67b738ef
......@@ -98,6 +98,14 @@ static inline struct radeon_i2c_bus_rec radeon_lookup_i2c_gpio(struct radeon_dev
}
}
/* some DCE3 boards have bad data for this entry */
if (ASIC_IS_DCE3(rdev)) {
if ((i == 4) &&
(gpio->usClkMaskRegisterIndex == 0x1fda) &&
(gpio->sucI2cId.ucAccess == 0x94))
gpio->sucI2cId.ucAccess = 0x14;
}
if (gpio->sucI2cId.ucAccess == id) {
i2c.mask_clk_reg = le16_to_cpu(gpio->usClkMaskRegisterIndex) * 4;
i2c.mask_data_reg = le16_to_cpu(gpio->usDataMaskRegisterIndex) * 4;
......@@ -174,6 +182,14 @@ void radeon_atombios_i2c_init(struct radeon_device *rdev)
}
}
/* some DCE3 boards have bad data for this entry */
if (ASIC_IS_DCE3(rdev)) {
if ((i == 4) &&
(gpio->usClkMaskRegisterIndex == 0x1fda) &&
(gpio->sucI2cId.ucAccess == 0x94))
gpio->sucI2cId.ucAccess = 0x14;
}
i2c.mask_clk_reg = le16_to_cpu(gpio->usClkMaskRegisterIndex) * 4;
i2c.mask_data_reg = le16_to_cpu(gpio->usDataMaskRegisterIndex) * 4;
i2c.en_clk_reg = le16_to_cpu(gpio->usClkEnRegisterIndex) * 4;
......
drivers/gpu/drm/radeon/radeon_combios.c
浏览文件 @ 67b738ef
......@@ -729,7 +729,7 @@ void radeon_combios_i2c_init(struct radeon_device *rdev)
clk = RBIOS8(offset + 3 + (i * 5) + 3);
data = RBIOS8(offset + 3 + (i * 5) + 4);
i2c = combios_setup_i2c_bus(rdev, DDC_MONID,
clk, data);
(1 << clk), (1 << data));
rdev->i2c_bus[4] = radeon_i2c_create(dev, &i2c, "GPIOPAD_MASK");
break;
}
......
drivers/hid/hid-core.c
浏览文件 @ 67b738ef
......@@ -1386,6 +1386,7 @@ static const struct hid_device_id hid_blacklist[] = {
{ HID_USB_DEVICE(USB_VENDOR_ID_THRUSTMASTER, 0xb651) },
{ HID_USB_DEVICE(USB_VENDOR_ID_THRUSTMASTER, 0xb653) },
{ HID_USB_DEVICE(USB_VENDOR_ID_THRUSTMASTER, 0xb654) },
{ HID_USB_DEVICE(USB_VENDOR_ID_THRUSTMASTER, 0xb65a) },
{ HID_USB_DEVICE(USB_VENDOR_ID_TOPSEED, USB_DEVICE_ID_TOPSEED_CYBERLINK) },
{ HID_USB_DEVICE(USB_VENDOR_ID_TOPSEED2, USB_DEVICE_ID_TOPSEED2_RF_COMBO) },
{ HID_USB_DEVICE(USB_VENDOR_ID_TWINHAN, USB_DEVICE_ID_TWINHAN_IR_REMOTE) },
......
drivers/hid/hid-egalax.c
浏览文件 @ 67b738ef
......@@ -221,7 +221,7 @@ static int egalax_probe(struct hid_device *hdev, const struct hid_device_id *id)
struct egalax_data *td;
struct hid_report *report;
td = kmalloc(sizeof(struct egalax_data), GFP_KERNEL);
td = kzalloc(sizeof(struct egalax_data), GFP_KERNEL);
if (!td) {
dev_err(&hdev->dev, "cannot allocate eGalax data\n");
return -ENOMEM;
......
drivers/hid/hid-input.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/hid/hid-tmff.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/i2c/Kconfig
浏览文件 @ 67b738ef
此差异已折叠。
drivers/i2c/algos/Kconfig
浏览文件 @ 67b738ef
此差异已折叠。
drivers/infiniband/core/ud_header.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/infiniband/hw/mlx4/main.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/infiniband/hw/mlx4/qp.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/input/serio/gscps2.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/leds/Kconfig
浏览文件 @ 67b738ef
此差异已折叠。
drivers/macintosh/Kconfig
浏览文件 @ 67b738ef
此差异已折叠。
drivers/media/common/tuners/Kconfig
浏览文件 @ 67b738ef
此差异已折叠。
drivers/media/dvb/frontends/Kconfig
浏览文件 @ 67b738ef
此差异已折叠。
drivers/media/radio/radio-si4713.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/media/video/Kconfig
浏览文件 @ 67b738ef
此差异已折叠。
drivers/media/video/cafe_ccic.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/media/video/cx18/cx18-i2c.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/media/video/fsl-viu.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/media/video/ivtv/ivtv-i2c.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/media/video/mxb.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/media/video/sh_vou.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/media/video/soc_camera.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/media/video/v4l2-common.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/media/video/via-camera.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/media/video/vino.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/mtd/ubi/io.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/mtd/ubi/scan.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/net/mlx4/fw.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/net/wan/x25_asy.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/parisc/dino.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/parisc/eisa.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/parisc/gsc.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/parisc/iosapic.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/parisc/led.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/parisc/superio.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/pcmcia/soc_common.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/regulator/core.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/regulator/twl-regulator.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/serial/8250.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/serial/mfd.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/spi/atmel_spi.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/staging/brcm80211/README
浏览文件 @ 67b738ef
此差异已折叠。
drivers/staging/brcm80211/TODO
浏览文件 @ 67b738ef
此差异已折叠。
drivers/staging/easycap/easycap.h
浏览文件 @ 67b738ef
此差异已折叠。
drivers/staging/line6/control.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/staging/line6/midi.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/staging/line6/pcm.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/staging/line6/pod.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/staging/line6/toneport.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/staging/line6/variax.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/staging/speakup/fakekey.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/staging/spectra/ffsport.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/staging/udlfb/udlfb.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/staging/winbond/sysdef.h
浏览文件 @ 67b738ef
此差异已折叠。
drivers/staging/zram/zram_sysfs.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/tty/tty_io.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/tty/tty_ldisc.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/uio/uio.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/uio/uio_cif.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/uio/uio_netx.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/usb/core/hcd.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/usb/host/ehci-pci.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/usb/host/xhci-hub.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/usb/host/xhci-mem.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/usb/host/xhci.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/usb/host/xhci.h
浏览文件 @ 67b738ef
此差异已折叠。
drivers/usb/misc/yurex.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/usb/musb/musb_core.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/usb/musb/musb_gadget.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/usb/serial/ftdi_sio.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/usb/serial/ftdi_sio_ids.h
浏览文件 @ 67b738ef
此差异已折叠。
drivers/usb/serial/usb-serial.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/video/da8xx-fb.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/video/fbcmap.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/video/geode/lxfb.h
浏览文件 @ 67b738ef
此差异已折叠。
drivers/video/geode/lxfb_ops.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/watchdog/Kconfig
浏览文件 @ 67b738ef
此差异已折叠。
drivers/watchdog/bcm63xx_wdt.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/watchdog/gef_wdt.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/watchdog/iTCO_wdt.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/xen/balloon.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/xen/events.c
浏览文件 @ 67b738ef
此差异已折叠。
drivers/xen/manage.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/cifs/Kconfig
浏览文件 @ 67b738ef
此差异已折叠。
fs/cifs/cifsacl.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/cifs/cifsfs.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/cifs/cifsproto.h
浏览文件 @ 67b738ef
此差异已折叠。
fs/cifs/connect.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/cifs/dns_resolve.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/cifs/file.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/cifs/fscache.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/cifs/inode.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/cifs/readdir.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/cifs/xattr.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/compat.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/exec.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/nfs/dir.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/ocfs2/cluster/heartbeat.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/ocfs2/dcache.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/ocfs2/dlm/dlmdomain.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/ocfs2/ocfs2.h
浏览文件 @ 67b738ef
此差异已折叠。
fs/ocfs2/stack_user.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/proc/base.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/reiserfs/xattr_acl.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/xfs/linux-2.6/xfs_aops.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/xfs/linux-2.6/xfs_buf.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/xfs/xfs_bmap.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/xfs/xfs_bmap.h
浏览文件 @ 67b738ef
此差异已折叠。
fs/xfs/xfs_dfrag.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/xfs/xfs_error.c
浏览文件 @ 67b738ef
此差异已折叠。
fs/xfs/xfs_error.h
浏览文件 @ 67b738ef
此差异已折叠。
fs/xfs/xfs_inode_item.c
浏览文件 @ 67b738ef
此差异已折叠。
include/linux/binfmts.h
浏览文件 @ 67b738ef
此差异已折叠。
include/linux/cpu.h
浏览文件 @ 67b738ef
此差异已折叠。
include/linux/gfp.h
浏览文件 @ 67b738ef
此差异已折叠。
include/linux/memory_hotplug.h
浏览文件 @ 67b738ef
此差异已折叠。
include/linux/node.h
浏览文件 @ 67b738ef
此差异已折叠。
include/linux/tty.h
浏览文件 @ 67b738ef
此差异已折叠。
include/linux/uio_driver.h
浏览文件 @ 67b738ef
此差异已折叠。
include/linux/usb.h
浏览文件 @ 67b738ef
此差异已折叠。
include/linux/vmalloc.h
浏览文件 @ 67b738ef
此差异已折叠。
include/media/v4l2-common.h
浏览文件 @ 67b738ef
此差异已折叠。
include/xen/events.h
浏览文件 @ 67b738ef
此差异已折叠。
include/xen/interface/physdev.h
浏览文件 @ 67b738ef
此差异已折叠。
kernel/exit.c
浏览文件 @ 67b738ef
此差异已折叠。
kernel/power/hibernate.c
浏览文件 @ 67b738ef
此差异已折叠。
kernel/power/suspend.c
浏览文件 @ 67b738ef
此差异已折叠。
kernel/power/swap.c
浏览文件 @ 67b738ef
此差异已折叠。
kernel/power/user.c
浏览文件 @ 67b738ef
此差异已折叠。
mm/hugetlb.c
浏览文件 @ 67b738ef
此差异已折叠。
mm/ksm.c
浏览文件 @ 67b738ef
此差异已折叠。
mm/memory-failure.c
浏览文件 @ 67b738ef
此差异已折叠。
mm/memory_hotplug.c
浏览文件 @ 67b738ef
此差异已折叠。
mm/mempolicy.c
浏览文件 @ 67b738ef
此差异已折叠。
mm/page_alloc.c
浏览文件 @ 67b738ef
此差异已折叠。
mm/slub.c
浏览文件 @ 67b738ef
此差异已折叠。
mm/vmalloc.c
浏览文件 @ 67b738ef
此差异已折叠。
mm/vmstat.c
浏览文件 @ 67b738ef
此差异已折叠。
net/mac80211/Kconfig
浏览文件 @ 67b738ef
此差异已折叠。
scripts/kconfig/expr.h
浏览文件 @ 67b738ef
此差异已折叠。
scripts/kconfig/lkc.h
浏览文件 @ 67b738ef
此差异已折叠。
scripts/kconfig/menu.c
浏览文件 @ 67b738ef
此差异已折叠。
scripts/kconfig/zconf.gperf
浏览文件 @ 67b738ef
此差异已折叠。
scripts/kconfig/zconf.tab.c_shipped
浏览文件 @ 67b738ef
此差异已折叠。
scripts/kconfig/zconf.y
浏览文件 @ 67b738ef
此差异已折叠。
sound/core/oss/pcm_oss.c
浏览文件 @ 67b738ef
此差异已折叠。
sound/pci/hda/patch_realtek.c
浏览文件 @ 67b738ef
此差异已折叠。
sound/pci/hda/patch_sigmatel.c
浏览文件 @ 67b738ef
此差异已折叠。
sound/soc/codecs/wm8731.c
浏览文件 @ 67b738ef
此差异已折叠。
sound/soc/fsl/mpc8610_hpcd.c
浏览文件 @ 67b738ef
此差异已折叠。
sound/soc/fsl/p1022_ds.c
浏览文件 @ 67b738ef
此差异已折叠。
sound/soc/nuc900/nuc900-ac97.c
浏览文件 @ 67b738ef
此差异已折叠。
sound/soc/nuc900/nuc900-audio.h
浏览文件 @ 67b738ef
此差异已折叠。
sound/soc/nuc900/nuc900-pcm.c
浏览文件 @ 67b738ef
此差异已折叠。
sound/soc/omap/Kconfig
浏览文件 @ 67b738ef
此差异已折叠。
sound/soc/s6000/s6000-i2s.c
浏览文件 @ 67b738ef
此差异已折叠。
sound/soc/s6000/s6000-pcm.c
浏览文件 @ 67b738ef
此差异已折叠。
sound/soc/s6000/s6105-ipcam.c
浏览文件 @ 67b738ef
此差异已折叠。
usr/initramfs_data.S
浏览文件 @ 67b738ef
此差异已折叠。
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或