V4L/DVB (10012): m5602: Start to unify read/write sensor functions

First step into unifying the read and write sensor functions
Signed-off-by: NErik Andrén <erik.andren@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/video/gspca/m5602/m5602_core.c

@@ -80,6 +80,50 @@ int m5602_write_bridge(struct sd *sd, u8 address, u8 i2c_data)
 	return (err < 0) ? err : 0;
 }
 
+int m5602_write_sensor(struct sd *sd, const u8 address,
+			u8 *i2c_data, const u8 len)
+{
+	int err, i;
+	u8 *p;
+	struct usb_device *udev = sd->gspca_dev.dev;
+	__u8 *buf = sd->gspca_dev.usb_buf;
+
+	/* No sensor with a data width larger than 16 bits has yet been seen */
+	if (len > sd->sensor->i2c_regW || !len)
+		return -EINVAL;
+
+	memcpy(buf, sensor_urb_skeleton,
+	       sizeof(sensor_urb_skeleton));
+
+	buf[11] = sd->sensor->i2c_slave_id;
+	buf[15] = address;
+
+	/* Special case larger sensor writes */
+	p = buf + 16;
+
+	/* Copy a four byte write sequence for each byte to be written to */
+	for (i = 0; i < len; i++) {
+		memcpy(p, sensor_urb_skeleton + 16, 4);
+		p[3] = i2c_data[i];
+		p += 4;
+		PDEBUG(D_CONF, "Writing sensor register 0x%x with 0x%x",
+		       address, i2c_data[i]);
+	}
+
+	/* Copy the tailer */
+	memcpy(p, sensor_urb_skeleton + 20, 4);
+
+	/* Set the total length */
+	p[3] = 0x10 + len;
+
+	err = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
+			      0x04, 0x40, 0x19,
+			      0x0000, buf,
+			      20 + len * 4, M5602_URB_MSG_TIMEOUT);
+
+	return (err < 0) ? err : 0;
+}
+
 /* Dump all the registers of the m5602 bridge,
    unfortunately this breaks the camera until it's power cycled */
 static void m5602_dump_bridge(struct sd *sd)

drivers/media/video/gspca/m5602/m5602_mt9m111.h

@@ -104,6 +104,7 @@ static struct m5602_sensor mt9m111 = {
 	.name = "MT9M111",
 
 	.i2c_slave_id = 0xba,
+	.i2c_regW = 2,
 
 	.probe = mt9m111_probe,
 	.init = mt9m111_init,

drivers/media/video/gspca/m5602/m5602_ov9650.h

@@ -153,6 +153,7 @@ int ov9650_set_auto_gain(struct gspca_dev *gspca_dev, __s32 val);
 static struct m5602_sensor ov9650 = {
 	.name = "OV9650",
 	.i2c_slave_id = 0x60,
+	.i2c_regW = 1,
 	.probe = ov9650_probe,
 	.init = ov9650_init,
 	.power_down = ov9650_power_down,

drivers/media/video/gspca/m5602/m5602_po1030.h

@@ -150,6 +150,7 @@ static struct m5602_sensor po1030 = {
 	.name = "PO1030",
 
 	.i2c_slave_id = 0xdc,
+	.i2c_regW = 1,
 
 	.probe = po1030_probe,
 	.init = po1030_init,

drivers/media/video/gspca/m5602/m5602_s5k4aa.h

@@ -87,6 +87,7 @@ static struct m5602_sensor s5k4aa = {
 	.init = s5k4aa_init,
 	.power_down = s5k4aa_power_down,
 	.i2c_slave_id = 0x5a,
+	.i2c_regW = 2,
 	.nctrls = 4,
 	.ctrls = {
 	{

drivers/media/video/gspca/m5602/m5602_s5k83a.h

@@ -69,6 +69,7 @@ static struct m5602_sensor s5k83a = {
 	.init = s5k83a_init,
 	.power_down = s5k83a_power_down,
 	.i2c_slave_id = 0x5a,
+	.i2c_regW = 2,
 	.nctrls = 5,
 	.ctrls = {
 	{

drivers/media/video/gspca/m5602/m5602_sensor.h

@@ -49,6 +49,9 @@ struct m5602_sensor {
 	/* What i2c address the sensor is connected to */
 	u8 i2c_slave_id;
 
+	/* Width of each i2c register (in bytes) */
+	u8 i2c_regW;
+
 	/* Probes if the sensor is connected */
 	int (*probe)(struct sd *sd);