Merge tag 'v3.3-rc7' into sched/core

Merge reason: merge back final fixes, prepare for the merge window.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Documentation/devicetree/bindings/gpio/led.txt

@@ -7,9 +7,9 @@ Each LED is represented as a sub-node of the gpio-leds device.  Each
 node's name represents the name of the corresponding LED.
 
 LED sub-node properties:
-- gpios :  Should specify the LED's GPIO, see "Specifying GPIO information
-  for devices" in Documentation/devicetree/booting-without-of.txt.  Active
-  low LEDs should be indicated using flags in the GPIO specifier.
+- gpios :  Should specify the LED's GPIO, see "gpios property" in
+  Documentation/devicetree/gpio.txt.  Active low LEDs should be
+  indicated using flags in the GPIO specifier.
 - label :  (optional) The label for this LED.  If omitted, the label is
   taken from the node name (excluding the unit address).
 - linux,default-trigger :  (optional) This parameter, if present, is a

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -30,6 +30,7 @@ national	National Semiconductor
 nintendo	Nintendo
 nvidia	NVIDIA
 nxp	NXP Semiconductors
+picochip	Picochip Ltd
 powervr	Imagination Technologies
 qcom	Qualcomm, Inc.
 ramtron	Ramtron International

Documentation/hwmon/jc42

@@ -7,21 +7,29 @@ Supported chips:
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
 	http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf
-  * IDT TSE2002B3, TS3000B3
-    Prefix: 'tse2002b3', 'ts3000b3'
+  * Atmel AT30TS00
+    Prefix: 'at30ts00'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
-	http://www.idt.com/products/getdoc.cfm?docid=18715691
-	http://www.idt.com/products/getdoc.cfm?docid=18715692
+	http://www.atmel.com/Images/doc8585.pdf
+  * IDT TSE2002B3, TSE2002GB2, TS3000B3, TS3000GB2
+    Prefix: 'tse2002', 'ts3000'
+    Addresses scanned: I2C 0x18 - 0x1f
+    Datasheets:
+	http://www.idt.com/sites/default/files/documents/IDT_TSE2002B3C_DST_20100512_120303152056.pdf
+	http://www.idt.com/sites/default/files/documents/IDT_TSE2002GB2A1_DST_20111107_120303145914.pdf
+	http://www.idt.com/sites/default/files/documents/IDT_TS3000B3A_DST_20101129_120303152013.pdf
+	http://www.idt.com/sites/default/files/documents/IDT_TS3000GB2A1_DST_20111104_120303151012.pdf
   * Maxim MAX6604
     Prefix: 'max6604'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
 	http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf
-  * Microchip MCP9805, MCP98242, MCP98243, MCP9843
-    Prefixes: 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
+  * Microchip MCP9804, MCP9805, MCP98242, MCP98243, MCP9843
+    Prefixes: 'mcp9804', 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
+	http://ww1.microchip.com/downloads/en/DeviceDoc/22203C.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf
@@ -48,6 +56,12 @@ Supported chips:
     Datasheets:
 	http://www.st.com/stonline/products/literature/ds/13447/stts424.pdf
 	http://www.st.com/stonline/products/literature/ds/13448/stts424e02.pdf
+  * ST Microelectronics STTS2002, STTS3000
+    Prefix: 'stts2002', 'stts3000'
+    Addresses scanned: I2C 0x18 - 0x1f
+    Datasheets:
+	http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00225278.pdf
+	http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATA_BRIEF/CD00270920.pdf
   * JEDEC JC 42.4 compliant temperature sensor chips
     Prefix: 'jc42'
     Addresses scanned: I2C 0x18 - 0x1f

Documentation/input/alps.txt

@@ -13,7 +13,8 @@ Detection
 
 All ALPS touchpads should respond to the "E6 report" command sequence:
 E8-E6-E6-E6-E9. An ALPS touchpad should respond with either 00-00-0A or
-00-00-64.
+00-00-64 if no buttons are pressed. The bits 0-2 of the first byte will be 1s
+if some buttons are pressed.
 
 If the E6 report is successful, the touchpad model is identified using the "E7
 report" sequence: E8-E7-E7-E7-E9. The response is the model signature and is

Documentation/kernel-parameters.txt

@@ -2211,6 +2211,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 
 			default: off.
 
+	printk.always_kmsg_dump=
+			Trigger kmsg_dump for cases other than kernel oops or
+			panics
+			Format: <bool>  (1/Y/y=enable, 0/N/n=disable)
+			default: disabled
+
 	printk.time=	Show timing data prefixed to each printk message line
 			Format: <bool>  (1/Y/y=enable, 0/N/n=disable)
 

MAINTAINERS

@@ -962,7 +962,7 @@ F:	drivers/tty/serial/msm_serial.c
 F:	drivers/platform/msm/
 F:	drivers/*/pm8???-*
 F:	include/linux/mfd/pm8xxx/
-T:	git git://codeaurora.org/quic/kernel/davidb/linux-msm.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm.git
 S:	Maintained
 
 ARM/TOSA MACHINE SUPPORT
@@ -1310,7 +1310,7 @@ F:	drivers/atm/
 F:	include/linux/atm*
 
 ATMEL AT91 MCI DRIVER
-M:	Nicolas Ferre <nicolas.ferre@atmel.com>
+M:	Ludovic Desroches <ludovic.desroches@atmel.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 W:	http://www.atmel.com/products/AT91/
 W:	http://www.at91.com/
@@ -1318,7 +1318,7 @@ S:	Maintained
 F:	drivers/mmc/host/at91_mci.c
 
 ATMEL AT91 / AT32 MCI DRIVER
-M:	Nicolas Ferre <nicolas.ferre@atmel.com>
+M:	Ludovic Desroches <ludovic.desroches@atmel.com>
 S:	Maintained
 F:	drivers/mmc/host/atmel-mci.c
 F:	drivers/mmc/host/atmel-mci-regs.h
@@ -7271,7 +7271,7 @@ WATCHDOG DEVICE DRIVERS
 M:	Wim Van Sebroeck <wim@iguana.be>
 L:	linux-watchdog@vger.kernel.org
 W:	http://www.linux-watchdog.org/
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog.git
+T:	git git://www.linux-watchdog.org/linux-watchdog.git
 S:	Maintained
 F:	Documentation/watchdog/
 F:	drivers/watchdog/

Makefile

 VERSION = 3
 PATCHLEVEL = 3
 SUBLEVEL = 0
-EXTRAVERSION = -rc5
+EXTRAVERSION = -rc7
 NAME = Saber-toothed Squirrel
 
 # *DOCUMENTATION*

arch/alpha/include/asm/futex.h

@@ -108,7 +108,7 @@ futex_atomic_cmpxchg_inatomic(u32 *uval, u32 __user *uaddr,
 	"	lda	$31,3b-2b(%0)\n"
 	"	.previous\n"
 	:	"+r"(ret), "=&r"(prev), "=&r"(cmp)
-	:	"r"(uaddr), "r"((long)oldval), "r"(newval)
+	:	"r"(uaddr), "r"((long)(int)oldval), "r"(newval)
 	:	"memory");
 
 	*uval = prev;

arch/arm/Kconfig

@@ -1280,7 +1280,7 @@ config ARM_ERRATA_743622
 	depends on CPU_V7
 	help
 	  This option enables the workaround for the 743622 Cortex-A9
-	  (r2p0..r2p2) erratum. Under very rare conditions, a faulty
+	  (r2p*) erratum. Under very rare conditions, a faulty
 	  optimisation in the Cortex-A9 Store Buffer may lead to data
 	  corruption. This workaround sets a specific bit in the diagnostic
 	  register of the Cortex-A9 which disables the Store Buffer

arch/arm/boot/.gitignore

@@ -3,3 +3,4 @@ zImage
 xipImage
 bootpImage
 uImage
+*.dtb

arch/arm/include/asm/pmu.h

@@ -134,7 +134,7 @@ int __init armpmu_register(struct arm_pmu *armpmu, char *name, int type);
 
 u64 armpmu_event_update(struct perf_event *event,
 			struct hw_perf_event *hwc,
-			int idx, int overflow);
+			int idx);
 
 int armpmu_event_set_period(struct perf_event *event,
 			    struct hw_perf_event *hwc,

arch/arm/kernel/ecard.c

@@ -242,6 +242,7 @@ static void ecard_init_pgtables(struct mm_struct *mm)
 
 	memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (EASI_SIZE / PGDIR_SIZE));
 
+	vma.vm_flags = VM_EXEC;
 	vma.vm_mm = mm;
 
 	flush_tlb_range(&vma, IO_START, IO_START + IO_SIZE);

arch/arm/kernel/perf_event.c

@@ -180,7 +180,7 @@ armpmu_event_set_period(struct perf_event *event,
 u64
 armpmu_event_update(struct perf_event *event,
 		    struct hw_perf_event *hwc,
-		    int idx, int overflow)
+		    int idx)
 {
 	struct arm_pmu *armpmu = to_arm_pmu(event->pmu);
 	u64 delta, prev_raw_count, new_raw_count;
@@ -193,13 +193,7 @@ armpmu_event_update(struct perf_event *event,
 			     new_raw_count) != prev_raw_count)
 		goto again;
 
-	new_raw_count &= armpmu->max_period;
-	prev_raw_count &= armpmu->max_period;
-
-	if (overflow)
-		delta = armpmu->max_period - prev_raw_count + new_raw_count + 1;
-	else
-		delta = new_raw_count - prev_raw_count;
+	delta = (new_raw_count - prev_raw_count) & armpmu->max_period;
 
 	local64_add(delta, &event->count);
 	local64_sub(delta, &hwc->period_left);
@@ -216,7 +210,7 @@ armpmu_read(struct perf_event *event)
 	if (hwc->idx < 0)
 		return;
 
-	armpmu_event_update(event, hwc, hwc->idx, 0);
+	armpmu_event_update(event, hwc, hwc->idx);
 }
 
 static void
@@ -232,7 +226,7 @@ armpmu_stop(struct perf_event *event, int flags)
 	if (!(hwc->state & PERF_HES_STOPPED)) {
 		armpmu->disable(hwc, hwc->idx);
 		barrier(); /* why? */
-		armpmu_event_update(event, hwc, hwc->idx, 0);
+		armpmu_event_update(event, hwc, hwc->idx);
 		hwc->state |= PERF_HES_STOPPED | PERF_HES_UPTODATE;
 	}
 }
@@ -518,7 +512,13 @@ __hw_perf_event_init(struct perf_event *event)
 	hwc->config_base	    |= (unsigned long)mapping;
 
 	if (!hwc->sample_period) {
-		hwc->sample_period  = armpmu->max_period;
+		/*
+		 * For non-sampling runs, limit the sample_period to half
+		 * of the counter width. That way, the new counter value
+		 * is far less likely to overtake the previous one unless
+		 * you have some serious IRQ latency issues.
+		 */
+		hwc->sample_period  = armpmu->max_period >> 1;
 		hwc->last_period    = hwc->sample_period;
 		local64_set(&hwc->period_left, hwc->sample_period);
 	}
@@ -679,6 +679,28 @@ static void __init cpu_pmu_init(struct arm_pmu *armpmu)
 	armpmu->type = ARM_PMU_DEVICE_CPU;
 }
 
+/*
+ * PMU hardware loses all context when a CPU goes offline.
+ * When a CPU is hotplugged back in, since some hardware registers are
+ * UNKNOWN at reset, the PMU must be explicitly reset to avoid reading
+ * junk values out of them.
+ */
+static int __cpuinit pmu_cpu_notify(struct notifier_block *b,
+					unsigned long action, void *hcpu)
+{
+	if ((action & ~CPU_TASKS_FROZEN) != CPU_STARTING)
+		return NOTIFY_DONE;
+
+	if (cpu_pmu && cpu_pmu->reset)
+		cpu_pmu->reset(NULL);
+
+	return NOTIFY_OK;
+}
+
+static struct notifier_block __cpuinitdata pmu_cpu_notifier = {
+	.notifier_call = pmu_cpu_notify,
+};
+
 /*
  * CPU PMU identification and registration.
  */
@@ -730,6 +752,7 @@ init_hw_perf_events(void)
 		pr_info("enabled with %s PMU driver, %d counters available\n",
 			cpu_pmu->name, cpu_pmu->num_events);
 		cpu_pmu_init(cpu_pmu);
+		register_cpu_notifier(&pmu_cpu_notifier);
 		armpmu_register(cpu_pmu, "cpu", PERF_TYPE_RAW);
 	} else {
 		pr_info("no hardware support available\n");

arch/arm/kernel/perf_event_v6.c

@@ -467,23 +467,6 @@ armv6pmu_enable_event(struct hw_perf_event *hwc,
 	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
-static int counter_is_active(unsigned long pmcr, int idx)
-{
-	unsigned long mask = 0;
-	if (idx == ARMV6_CYCLE_COUNTER)
-		mask = ARMV6_PMCR_CCOUNT_IEN;
-	else if (idx == ARMV6_COUNTER0)
-		mask = ARMV6_PMCR_COUNT0_IEN;
-	else if (idx == ARMV6_COUNTER1)
-		mask = ARMV6_PMCR_COUNT1_IEN;
-
-	if (mask)
-		return pmcr & mask;
-
-	WARN_ONCE(1, "invalid counter number (%d)\n", idx);
-	return 0;
-}
-
 static irqreturn_t
 armv6pmu_handle_irq(int irq_num,
 		    void *dev)
@@ -513,7 +496,8 @@ armv6pmu_handle_irq(int irq_num,
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
-		if (!counter_is_active(pmcr, idx))
+		/* Ignore if we don't have an event. */
+		if (!event)
 			continue;
 
 		/*
@@ -524,7 +508,7 @@ armv6pmu_handle_irq(int irq_num,
 			continue;
 
 		hwc = &event->hw;
-		armpmu_event_update(event, hwc, idx, 1);
+		armpmu_event_update(event, hwc, idx);
 		data.period = event->hw.last_period;
 		if (!armpmu_event_set_period(event, hwc, idx))
 			continue;

arch/arm/kernel/perf_event_v7.c

@@ -809,6 +809,11 @@ static inline int armv7_pmnc_disable_intens(int idx)
 
 	counter = ARMV7_IDX_TO_COUNTER(idx);
 	asm volatile("mcr p15, 0, %0, c9, c14, 2" : : "r" (BIT(counter)));
+	isb();
+	/* Clear the overflow flag in case an interrupt is pending. */
+	asm volatile("mcr p15, 0, %0, c9, c12, 3" : : "r" (BIT(counter)));
+	isb();
+
 	return idx;
 }
 
@@ -955,6 +960,10 @@ static irqreturn_t armv7pmu_handle_irq(int irq_num, void *dev)
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
+		/* Ignore if we don't have an event. */
+		if (!event)
+			continue;
+
 		/*
 		 * We have a single interrupt for all counters. Check that
 		 * each counter has overflowed before we process it.
@@ -963,7 +972,7 @@ static irqreturn_t armv7pmu_handle_irq(int irq_num, void *dev)
 			continue;
 
 		hwc = &event->hw;
-		armpmu_event_update(event, hwc, idx, 1);
+		armpmu_event_update(event, hwc, idx);
 		data.period = event->hw.last_period;
 		if (!armpmu_event_set_period(event, hwc, idx))
 			continue;

arch/arm/kernel/perf_event_xscale.c

@@ -255,11 +255,14 @@ xscale1pmu_handle_irq(int irq_num, void *dev)
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
+		if (!event)
+			continue;
+
 		if (!xscale1_pmnc_counter_has_overflowed(pmnc, idx))
 			continue;
 
 		hwc = &event->hw;
-		armpmu_event_update(event, hwc, idx, 1);
+		armpmu_event_update(event, hwc, idx);
 		data.period = event->hw.last_period;
 		if (!armpmu_event_set_period(event, hwc, idx))
 			continue;
@@ -592,11 +595,14 @@ xscale2pmu_handle_irq(int irq_num, void *dev)
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
-		if (!xscale2_pmnc_counter_has_overflowed(pmnc, idx))
+		if (!event)
+			continue;
+
+		if (!xscale2_pmnc_counter_has_overflowed(of_flags, idx))
 			continue;
 
 		hwc = &event->hw;
-		armpmu_event_update(event, hwc, idx, 1);
+		armpmu_event_update(event, hwc, idx);
 		data.period = event->hw.last_period;
 		if (!armpmu_event_set_period(event, hwc, idx))
 			continue;
@@ -663,7 +669,7 @@ xscale2pmu_enable_event(struct hw_perf_event *hwc, int idx)
 static void
 xscale2pmu_disable_event(struct hw_perf_event *hwc, int idx)
 {
-	unsigned long flags, ien, evtsel;
+	unsigned long flags, ien, evtsel, of_flags;
 	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
 	ien = xscale2pmu_read_int_enable();
@@ -672,26 +678,31 @@ xscale2pmu_disable_event(struct hw_perf_event *hwc, int idx)
 	switch (idx) {
 	case XSCALE_CYCLE_COUNTER:
 		ien &= ~XSCALE2_CCOUNT_INT_EN;
+		of_flags = XSCALE2_CCOUNT_OVERFLOW;
 		break;
 	case XSCALE_COUNTER0:
 		ien &= ~XSCALE2_COUNT0_INT_EN;
 		evtsel &= ~XSCALE2_COUNT0_EVT_MASK;
 		evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT0_EVT_SHFT;
+		of_flags = XSCALE2_COUNT0_OVERFLOW;
 		break;
 	case XSCALE_COUNTER1:
 		ien &= ~XSCALE2_COUNT1_INT_EN;
 		evtsel &= ~XSCALE2_COUNT1_EVT_MASK;
 		evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT1_EVT_SHFT;
+		of_flags = XSCALE2_COUNT1_OVERFLOW;
 		break;
 	case XSCALE_COUNTER2:
 		ien &= ~XSCALE2_COUNT2_INT_EN;
 		evtsel &= ~XSCALE2_COUNT2_EVT_MASK;
 		evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT2_EVT_SHFT;
+		of_flags = XSCALE2_COUNT2_OVERFLOW;
 		break;
 	case XSCALE_COUNTER3:
 		ien &= ~XSCALE2_COUNT3_INT_EN;
 		evtsel &= ~XSCALE2_COUNT3_EVT_MASK;
 		evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT3_EVT_SHFT;
+		of_flags = XSCALE2_COUNT3_OVERFLOW;
 		break;
 	default:
 		WARN_ONCE(1, "invalid counter number (%d)\n", idx);
@@ -701,6 +712,7 @@ xscale2pmu_disable_event(struct hw_perf_event *hwc, int idx)
 	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	xscale2pmu_write_event_select(evtsel);
 	xscale2pmu_write_int_enable(ien);
+	xscale2pmu_write_overflow_flags(of_flags);
 	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 

arch/arm/mach-at91/at91sam9g45_devices.c

@@ -38,10 +38,6 @@
 #if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE)
 static u64 hdmac_dmamask = DMA_BIT_MASK(32);
 
-static struct at_dma_platform_data atdma_pdata = {
-	.nr_channels	= 8,
-};
-
 static struct resource hdmac_resources[] = {
 	[0] = {
 		.start	= AT91SAM9G45_BASE_DMA,
@@ -56,12 +52,11 @@ static struct resource hdmac_resources[] = {
 };
 
 static struct platform_device at_hdmac_device = {
-	.name		= "at_hdmac",
+	.name		= "at91sam9g45_dma",
 	.id		= -1,
 	.dev		= {
 				.dma_mask		= &hdmac_dmamask,
 				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &atdma_pdata,
 	},
 	.resource	= hdmac_resources,
 	.num_resources	= ARRAY_SIZE(hdmac_resources),
@@ -69,9 +64,15 @@ static struct platform_device at_hdmac_device = {
 
 void __init at91_add_device_hdmac(void)
 {
-	dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
-	dma_cap_set(DMA_SLAVE, atdma_pdata.cap_mask);
-	platform_device_register(&at_hdmac_device);
+#if defined(CONFIG_OF)
+	struct device_node *of_node =
+		of_find_node_by_name(NULL, "dma-controller");
+
+	if (of_node)
+		of_node_put(of_node);
+	else
+#endif
+		platform_device_register(&at_hdmac_device);
 }
 #else
 void __init at91_add_device_hdmac(void) {}

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -33,10 +33,6 @@
 #if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE)
 static u64 hdmac_dmamask = DMA_BIT_MASK(32);
 
-static struct at_dma_platform_data atdma_pdata = {
-	.nr_channels	= 2,
-};
-
 static struct resource hdmac_resources[] = {
 	[0] = {
 		.start	= AT91SAM9RL_BASE_DMA,
@@ -51,12 +47,11 @@ static struct resource hdmac_resources[] = {
 };
 
 static struct platform_device at_hdmac_device = {
-	.name		= "at_hdmac",
+	.name		= "at91sam9rl_dma",
 	.id		= -1,
 	.dev		= {
 				.dma_mask		= &hdmac_dmamask,
 				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &atdma_pdata,
 	},
 	.resource	= hdmac_resources,
 	.num_resources	= ARRAY_SIZE(hdmac_resources),
@@ -64,7 +59,6 @@ static struct platform_device at_hdmac_device = {
 
 void __init at91_add_device_hdmac(void)
 {
-	dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
 	platform_device_register(&at_hdmac_device);
 }
 #else

arch/arm/mach-ep93xx/vision_ep9307.c

@@ -34,6 +34,7 @@
 #include <mach/ep93xx_spi.h>
 #include <mach/gpio-ep93xx.h>
 
+#include <asm/hardware/vic.h>
 #include <asm/mach-types.h>
 #include <asm/mach/map.h>
 #include <asm/mach/arch.h>
@@ -361,6 +362,7 @@ MACHINE_START(VISION_EP9307, "Vision Engraving Systems EP9307")
 	.atag_offset	= 0x100,
 	.map_io		= vision_map_io,
 	.init_irq	= ep93xx_init_irq,
+	.handle_irq	= vic_handle_irq,
 	.timer		= &ep93xx_timer,
 	.init_machine	= vision_init_machine,
 	.restart	= ep93xx_restart,

arch/arm/mach-exynos/mach-universal_c210.c

@@ -13,6 +13,7 @@
 #include <linux/i2c.h>
 #include <linux/gpio_keys.h>
 #include <linux/gpio.h>
+#include <linux/interrupt.h>
 #include <linux/fb.h>
 #include <linux/mfd/max8998.h>
 #include <linux/regulator/machine.h>
@@ -595,6 +596,7 @@ static struct mxt_platform_data qt602240_platform_data = {
 	.threshold	= 0x28,
 	.voltage	= 2800000,		/* 2.8V */
 	.orient		= MXT_DIAGONAL,
+	.irqflags	= IRQF_TRIGGER_FALLING,
 };
 
 static struct i2c_board_info i2c3_devs[] __initdata = {

arch/arm/mach-lpc32xx/include/mach/irqs.h

@@ -61,7 +61,7 @@
  */
 #define IRQ_LPC32XX_JTAG_COMM_TX	LPC32XX_SIC1_IRQ(1)
 #define IRQ_LPC32XX_JTAG_COMM_RX	LPC32XX_SIC1_IRQ(2)
-#define IRQ_LPC32XX_GPI_11		LPC32XX_SIC1_IRQ(4)
+#define IRQ_LPC32XX_GPI_28		LPC32XX_SIC1_IRQ(4)
 #define IRQ_LPC32XX_TS_P		LPC32XX_SIC1_IRQ(6)
 #define IRQ_LPC32XX_TS_IRQ		LPC32XX_SIC1_IRQ(7)
 #define IRQ_LPC32XX_TS_AUX		LPC32XX_SIC1_IRQ(8)

arch/arm/mach-lpc32xx/irq.c

@@ -118,6 +118,10 @@ static const struct lpc32xx_event_info lpc32xx_events[NR_IRQS] = {
 		.event_group = &lpc32xx_event_pin_regs,
 		.mask = LPC32XX_CLKPWR_EXTSRC_GPI_06_BIT,
 	},
+	[IRQ_LPC32XX_GPI_28] = {
+		.event_group = &lpc32xx_event_pin_regs,
+		.mask = LPC32XX_CLKPWR_EXTSRC_GPI_28_BIT,
+	},
 	[IRQ_LPC32XX_GPIO_00] = {
 		.event_group = &lpc32xx_event_int_regs,
 		.mask = LPC32XX_CLKPWR_INTSRC_GPIO_00_BIT,
@@ -305,9 +309,18 @@ static int lpc32xx_irq_wake(struct irq_data *d, unsigned int state)
 
 		if (state)
 			eventreg |= lpc32xx_events[d->irq].mask;
-		else
+		else {
 			eventreg &= ~lpc32xx_events[d->irq].mask;
 
+			/*
+			 * When disabling the wakeup, clear the latched
+			 * event
+			 */
+			__raw_writel(lpc32xx_events[d->irq].mask,
+				lpc32xx_events[d->irq].
+				event_group->rawstat_reg);
+		}
+
 		__raw_writel(eventreg,
 			lpc32xx_events[d->irq].event_group->enab_reg);
 
@@ -380,13 +393,15 @@ void __init lpc32xx_init_irq(void)
 
 	/* Setup SIC1 */
 	__raw_writel(0, LPC32XX_INTC_MASK(LPC32XX_SIC1_BASE));
-	__raw_writel(MIC_APR_DEFAULT, LPC32XX_INTC_POLAR(LPC32XX_SIC1_BASE));
-	__raw_writel(MIC_ATR_DEFAULT, LPC32XX_INTC_ACT_TYPE(LPC32XX_SIC1_BASE));
+	__raw_writel(SIC1_APR_DEFAULT, LPC32XX_INTC_POLAR(LPC32XX_SIC1_BASE));
+	__raw_writel(SIC1_ATR_DEFAULT,
+				LPC32XX_INTC_ACT_TYPE(LPC32XX_SIC1_BASE));
 
 	/* Setup SIC2 */
 	__raw_writel(0, LPC32XX_INTC_MASK(LPC32XX_SIC2_BASE));
-	__raw_writel(MIC_APR_DEFAULT, LPC32XX_INTC_POLAR(LPC32XX_SIC2_BASE));
-	__raw_writel(MIC_ATR_DEFAULT, LPC32XX_INTC_ACT_TYPE(LPC32XX_SIC2_BASE));
+	__raw_writel(SIC2_APR_DEFAULT, LPC32XX_INTC_POLAR(LPC32XX_SIC2_BASE));
+	__raw_writel(SIC2_ATR_DEFAULT,
+				LPC32XX_INTC_ACT_TYPE(LPC32XX_SIC2_BASE));
 
 	/* Configure supported IRQ's */
 	for (i = 0; i < NR_IRQS; i++) {

arch/arm/mach-lpc32xx/serial.c

@@ -88,6 +88,7 @@ struct uartinit {
 	char *uart_ck_name;
 	u32 ck_mode_mask;
 	void __iomem *pdiv_clk_reg;
+	resource_size_t mapbase;
 };
 
 static struct uartinit uartinit_data[] __initdata = {
@@ -97,6 +98,7 @@ static struct uartinit uartinit_data[] __initdata = {
 		.ck_mode_mask =
 			LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 5),
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART5_CLK_CTRL,
+		.mapbase = LPC32XX_UART5_BASE,
 	},
 #endif
 #ifdef CONFIG_ARCH_LPC32XX_UART3_SELECT
@@ -105,6 +107,7 @@ static struct uartinit uartinit_data[] __initdata = {
 		.ck_mode_mask =
 			LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 3),
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART3_CLK_CTRL,
+		.mapbase = LPC32XX_UART3_BASE,
 	},
 #endif
 #ifdef CONFIG_ARCH_LPC32XX_UART4_SELECT
@@ -113,6 +116,7 @@ static struct uartinit uartinit_data[] __initdata = {
 		.ck_mode_mask =
 			LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 4),
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART4_CLK_CTRL,
+		.mapbase = LPC32XX_UART4_BASE,
 	},
 #endif
 #ifdef CONFIG_ARCH_LPC32XX_UART6_SELECT
@@ -121,6 +125,7 @@ static struct uartinit uartinit_data[] __initdata = {
 		.ck_mode_mask =
 			LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 6),
 		.pdiv_clk_reg = LPC32XX_CLKPWR_UART6_CLK_CTRL,
+		.mapbase = LPC32XX_UART6_BASE,
 	},
 #endif
 };
@@ -165,11 +170,24 @@ void __init lpc32xx_serial_init(void)
 
 		/* pre-UART clock divider set to 1 */
 		__raw_writel(0x0101, uartinit_data[i].pdiv_clk_reg);
+
+		/*
+		 * Force a flush of the RX FIFOs to work around a
+		 * HW bug
+		 */
+		puart = uartinit_data[i].mapbase;
+		__raw_writel(0xC1, LPC32XX_UART_IIR_FCR(puart));
+		__raw_writel(0x00, LPC32XX_UART_DLL_FIFO(puart));
+		j = LPC32XX_SUART_FIFO_SIZE;
+		while (j--)
+			tmp = __raw_readl(
+				LPC32XX_UART_DLL_FIFO(puart));
+		__raw_writel(0, LPC32XX_UART_IIR_FCR(puart));
 	}
 
 	/* This needs to be done after all UART clocks are setup */
 	__raw_writel(clkmodes, LPC32XX_UARTCTL_CLKMODE);
-	for (i = 0; i < ARRAY_SIZE(uartinit_data) - 1; i++) {
+	for (i = 0; i < ARRAY_SIZE(uartinit_data); i++) {
 		/* Force a flush of the RX FIFOs to work around a HW bug */
 		puart = serial_std_platform_data[i].mapbase;
 		__raw_writel(0xC1, LPC32XX_UART_IIR_FCR(puart));

arch/arm/mach-mmp/aspenite.c

@@ -17,7 +17,6 @@
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/nand.h>
 #include <linux/interrupt.h>
-#include <linux/gpio.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>

arch/arm/mach-mmp/pxa168.c

@@ -24,7 +24,6 @@
 #include <mach/dma.h>
 #include <mach/devices.h>
 #include <mach/mfp.h>
-#include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
 #include <mach/pxa168.h>
 

arch/arm/mach-mmp/tavorevb.c

@@ -12,7 +12,6 @@
 #include <linux/kernel.h>
 #include <linux/platform_device.h>
 #include <linux/smc91x.h>
-#include <linux/gpio.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>

arch/arm/mach-omap1/board-innovator.c

@@ -416,13 +416,13 @@ static void __init innovator_init(void)
 #ifdef CONFIG_ARCH_OMAP15XX
 	if (cpu_is_omap1510()) {
 		omap1_usb_init(&innovator1510_usb_config);
-		innovator_config[1].data = &innovator1510_lcd_config;
+		innovator_config[0].data = &innovator1510_lcd_config;
 	}
 #endif
 #ifdef CONFIG_ARCH_OMAP16XX
 	if (cpu_is_omap1610()) {
 		omap1_usb_init(&h2_usb_config);
-		innovator_config[1].data = &innovator1610_lcd_config;
+		innovator_config[0].data = &innovator1610_lcd_config;
 	}
 #endif
 	omap_board_config = innovator_config;

arch/arm/mach-omap2/Kconfig

@@ -364,8 +364,8 @@ config OMAP3_SDRC_AC_TIMING
 	  going on could result in system crashes;
 
 config OMAP4_ERRATA_I688
-	bool "OMAP4 errata: Async Bridge Corruption (BROKEN)"
-	depends on ARCH_OMAP4 && BROKEN
+	bool "OMAP4 errata: Async Bridge Corruption"
+	depends on ARCH_OMAP4
 	select ARCH_HAS_BARRIERS
 	help
 	  If a data is stalled inside asynchronous bridge because of back

arch/arm/mach-omap2/board-n8x0.c

@@ -371,7 +371,11 @@ static void n8x0_mmc_callback(void *data, u8 card_mask)
 	else
 		*openp = 0;
 
+#ifdef CONFIG_MMC_OMAP
 	omap_mmc_notify_cover_event(mmc_device, index, *openp);
+#else
+	pr_warn("MMC: notify cover event not available\n");
+#endif
 }
 
 static int n8x0_mmc_late_init(struct device *dev)

arch/arm/mach-omap2/board-omap3evm.c

@@ -381,7 +381,7 @@ static int omap3evm_twl_gpio_setup(struct device *dev,
 	gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
 
 	/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
-	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
+	gpio_leds[0].gpio = gpio + TWL4030_GPIO_MAX + 1;
 
 	platform_device_register(&leds_gpio);
 

arch/arm/mach-omap2/common.h

@@ -132,6 +132,7 @@ void omap3_map_io(void);
 void am33xx_map_io(void);
 void omap4_map_io(void);
 void ti81xx_map_io(void);
+void omap_barriers_init(void);
 
 /**
  * omap_test_timeout - busy-loop, testing a condition

arch/arm/mach-omap2/cpuidle44xx.c

@@ -65,7 +65,6 @@ static int omap4_enter_idle(struct cpuidle_device *dev,
 	struct timespec ts_preidle, ts_postidle, ts_idle;
 	u32 cpu1_state;
 	int idle_time;
-	int new_state_idx;
 	int cpu_id = smp_processor_id();
 
 	/* Used to keep track of the total time in idle */
@@ -84,8 +83,8 @@ static int omap4_enter_idle(struct cpuidle_device *dev,
 	 */
 	cpu1_state = pwrdm_read_pwrst(cpu1_pd);
 	if (cpu1_state != PWRDM_POWER_OFF) {
-		new_state_idx = drv->safe_state_index;
-		cx = cpuidle_get_statedata(&dev->states_usage[new_state_idx]);
+		index = drv->safe_state_index;
+		cx = cpuidle_get_statedata(&dev->states_usage[index]);
 	}
 
 	if (index > 0)

arch/arm/mach-omap2/gpmc-smsc911x.c

@@ -19,6 +19,8 @@
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/smsc911x.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 
 #include <plat/board.h>
 #include <plat/gpmc.h>
@@ -42,6 +44,50 @@ static struct smsc911x_platform_config gpmc_smsc911x_config = {
 	.flags		= SMSC911X_USE_16BIT,
 };
 
+static struct regulator_consumer_supply gpmc_smsc911x_supply[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
+};
+
+/* Generic regulator definition to satisfy smsc911x */
+static struct regulator_init_data gpmc_smsc911x_reg_init_data = {
+	.constraints = {
+		.min_uV			= 3300000,
+		.max_uV			= 3300000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= ARRAY_SIZE(gpmc_smsc911x_supply),
+	.consumer_supplies	= gpmc_smsc911x_supply,
+};
+
+static struct fixed_voltage_config gpmc_smsc911x_fixed_reg_data = {
+	.supply_name		= "gpmc_smsc911x",
+	.microvolts		= 3300000,
+	.gpio			= -EINVAL,
+	.startup_delay		= 0,
+	.enable_high		= 0,
+	.enabled_at_boot	= 1,
+	.init_data		= &gpmc_smsc911x_reg_init_data,
+};
+
+/*
+ * Platform device id of 42 is a temporary fix to avoid conflicts
+ * with other reg-fixed-voltage devices. The real fix should
+ * involve the driver core providing a way of dynamically
+ * assigning a unique id on registration for platform devices
+ * in the same name space.
+ */
+static struct platform_device gpmc_smsc911x_regulator = {
+	.name		= "reg-fixed-voltage",
+	.id		= 42,
+	.dev = {
+		.platform_data	= &gpmc_smsc911x_fixed_reg_data,
+	},
+};
+
 /*
  * Initialize smsc911x device connected to the GPMC. Note that we
  * assume that pin multiplexing is done in the board-*.c file,
@@ -55,6 +101,12 @@ void __init gpmc_smsc911x_init(struct omap_smsc911x_platform_data *board_data)
 
 	gpmc_cfg = board_data;
 
+	ret = platform_device_register(&gpmc_smsc911x_regulator);
+	if (ret < 0) {
+		pr_err("Unable to register smsc911x regulators: %d\n", ret);
+		return;
+	}
+
 	if (gpmc_cs_request(gpmc_cfg->cs, SZ_16M, &cs_mem_base) < 0) {
 		pr_err("Failed to request GPMC mem region\n");
 		return;

arch/arm/mach-omap2/hsmmc.c

@@ -428,6 +428,7 @@ static int omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c,
 	return 0;
 }
 
+static int omap_hsmmc_done;
 #define MAX_OMAP_MMC_HWMOD_NAME_LEN		16
 
 void omap_init_hsmmc(struct omap2_hsmmc_info *hsmmcinfo, int ctrl_nr)
@@ -491,6 +492,11 @@ void omap2_hsmmc_init(struct omap2_hsmmc_info *controllers)
 {
 	u32 reg;
 
+	if (omap_hsmmc_done)
+		return;
+
+	omap_hsmmc_done = 1;
+
 	if (!cpu_is_omap44xx()) {
 		if (cpu_is_omap2430()) {
 			control_pbias_offset = OMAP243X_CONTROL_PBIAS_LITE;

arch/arm/mach-omap2/id.c

@@ -343,6 +343,7 @@ static void __init omap3_check_revision(const char **cpu_rev)
 	case 0xb944:
 		omap_revision = AM335X_REV_ES1_0;
 		*cpu_rev = "1.0";
+		break;
 	case 0xb8f2:
 		switch (rev) {
 		case 0:

arch/arm/mach-omap2/io.c

@@ -307,6 +307,7 @@ void __init omapam33xx_map_common_io(void)
 void __init omap44xx_map_common_io(void)
 {
 	iotable_init(omap44xx_io_desc, ARRAY_SIZE(omap44xx_io_desc));
+	omap_barriers_init();
 }
 #endif
 

arch/arm/mach-omap2/mailbox.c

@@ -281,8 +281,16 @@ static struct omap_mbox mbox_iva_info = {
 	.ops	= &omap2_mbox_ops,
 	.priv	= &omap2_mbox_iva_priv,
 };
+#endif
 
-struct omap_mbox *omap2_mboxes[] = { &mbox_dsp_info, &mbox_iva_info, NULL };
+#ifdef CONFIG_ARCH_OMAP2
+struct omap_mbox *omap2_mboxes[] = {
+	&mbox_dsp_info,
+#ifdef CONFIG_SOC_OMAP2420
+	&mbox_iva_info,
+#endif
+	NULL
+};
 #endif
 
 #if defined(CONFIG_ARCH_OMAP4)
@@ -412,8 +420,7 @@ static void __exit omap2_mbox_exit(void)
 	platform_driver_unregister(&omap2_mbox_driver);
 }
 
-/* must be ready before omap3isp is probed */
-subsys_initcall(omap2_mbox_init);
+module_init(omap2_mbox_init);
 module_exit(omap2_mbox_exit);
 
 MODULE_LICENSE("GPL v2");

arch/arm/mach-omap2/mux.c

@@ -218,7 +218,7 @@ static int _omap_mux_get_by_name(struct omap_mux_partition *partition,
 	return -ENODEV;
 }
 
-static int __init
+static int
 omap_mux_get_by_name(const char *muxname,
 			struct omap_mux_partition **found_partition,
 			struct omap_mux **found_mux)

arch/arm/mach-omap2/omap-iommu.c

@@ -150,7 +150,8 @@ static int __init omap_iommu_init(void)
 		platform_device_put(omap_iommu_pdev[i]);
 	return err;
 }
-module_init(omap_iommu_init);
+/* must be ready before omap3isp is probed */
+subsys_initcall(omap_iommu_init);
 
 static void __exit omap_iommu_exit(void)
 {

arch/arm/mach-omap2/omap4-common.c

@@ -24,12 +24,14 @@
 
 #include <plat/irqs.h>
 #include <plat/sram.h>
+#include <plat/omap-secure.h>
 
 #include <mach/hardware.h>
 #include <mach/omap-wakeupgen.h>
 
 #include "common.h"
 #include "omap4-sar-layout.h"
+#include <linux/export.h>
 
 #ifdef CONFIG_CACHE_L2X0
 static void __iomem *l2cache_base;
@@ -43,6 +45,9 @@ static void __iomem *sar_ram_base;
 
 void __iomem *dram_sync, *sram_sync;
 
+static phys_addr_t paddr;
+static u32 size;
+
 void omap_bus_sync(void)
 {
 	if (dram_sync && sram_sync) {
@@ -51,19 +56,22 @@ void omap_bus_sync(void)
 		isb();
 	}
 }
+EXPORT_SYMBOL(omap_bus_sync);
 
-static int __init omap_barriers_init(void)
+/* Steal one page physical memory for barrier implementation */
+int __init omap_barrier_reserve_memblock(void)
 {
-	struct map_desc dram_io_desc[1];
-	phys_addr_t paddr;
-	u32 size;
-
-	if (!cpu_is_omap44xx())
-		return -ENODEV;
 
 	size = ALIGN(PAGE_SIZE, SZ_1M);
 	paddr = arm_memblock_steal(size, SZ_1M);
 
+	return 0;
+}
+
+void __init omap_barriers_init(void)
+{
+	struct map_desc dram_io_desc[1];
+
 	dram_io_desc[0].virtual = OMAP4_DRAM_BARRIER_VA;
 	dram_io_desc[0].pfn = __phys_to_pfn(paddr);
 	dram_io_desc[0].length = size;
@@ -75,9 +83,10 @@ static int __init omap_barriers_init(void)
 	pr_info("OMAP4: Map 0x%08llx to 0x%08lx for dram barrier\n",
 		(long long) paddr, dram_io_desc[0].virtual);
 
-	return 0;
 }
-core_initcall(omap_barriers_init);
+#else
+void __init omap_barriers_init(void)
+{}
 #endif
 
 void __init gic_init_irq(void)

arch/arm/mach-omap2/pm.c

@@ -174,14 +174,17 @@ static int __init omap2_set_init_voltage(char *vdd_name, char *clk_name,
 	freq = clk->rate;
 	clk_put(clk);
 
+	rcu_read_lock();
 	opp = opp_find_freq_ceil(dev, &freq);
 	if (IS_ERR(opp)) {
+		rcu_read_unlock();
 		pr_err("%s: unable to find boot up OPP for vdd_%s\n",
 			__func__, vdd_name);
 		goto exit;
 	}
 
 	bootup_volt = opp_get_voltage(opp);
+	rcu_read_unlock();
 	if (!bootup_volt) {
 		pr_err("%s: unable to find voltage corresponding "
 			"to the bootup OPP for vdd_%s\n", __func__, vdd_name);

arch/arm/mach-omap2/twl-common.c

@@ -270,7 +270,6 @@ static struct regulator_init_data omap4_vusb_idata = {
 	.constraints = {
 		.min_uV			= 3300000,
 		.max_uV			= 3300000,
-		.apply_uV		= true,
 		.valid_modes_mask	= REGULATOR_MODE_NORMAL
 					| REGULATOR_MODE_STANDBY,
 		.valid_ops_mask		= REGULATOR_CHANGE_MODE

arch/arm/mach-omap2/usb-host.c

@@ -486,7 +486,7 @@ static void setup_4430ohci_io_mux(const enum usbhs_omap_port_mode *port_mode)
 void __init usbhs_init(const struct usbhs_omap_board_data *pdata)
 {
 	struct omap_hwmod	*oh[2];
-	struct omap_device	*od;
+	struct platform_device	*pdev;
 	int			bus_id = -1;
 	int			i;
 
@@ -522,11 +522,11 @@ void __init usbhs_init(const struct usbhs_omap_board_data *pdata)
 		return;
 	}
 
-	od = omap_device_build_ss(OMAP_USBHS_DEVICE, bus_id, oh, 2,
+	pdev = omap_device_build_ss(OMAP_USBHS_DEVICE, bus_id, oh, 2,
 				(void *)&usbhs_data, sizeof(usbhs_data),
 				omap_uhhtll_latency,
 				ARRAY_SIZE(omap_uhhtll_latency), false);
-	if (IS_ERR(od)) {
+	if (IS_ERR(pdev)) {
 		pr_err("Could not build hwmod devices %s,%s\n",
 			USBHS_UHH_HWMODNAME, USBHS_TLL_HWMODNAME);
 		return;

arch/arm/mach-pxa/generic.h

@@ -49,7 +49,6 @@ extern unsigned pxa3xx_get_clk_frequency_khz(int);
 #endif
 
 extern struct syscore_ops pxa_irq_syscore_ops;
-extern struct syscore_ops pxa_gpio_syscore_ops;
 extern struct syscore_ops pxa2xx_mfp_syscore_ops;
 extern struct syscore_ops pxa3xx_mfp_syscore_ops;
 

arch/arm/mach-pxa/hx4700.c

@@ -45,6 +45,7 @@
 #include <mach/hx4700.h>
 #include <mach/irda.h>
 
+#include <sound/ak4641.h>
 #include <video/platform_lcd.h>
 #include <video/w100fb.h>
 
@@ -764,6 +765,28 @@ static struct i2c_board_info __initdata pi2c_board_info[] = {
 	},
 };
 
+/*
+ * Asahi Kasei AK4641 on I2C
+ */
+
+static struct ak4641_platform_data ak4641_info = {
+	.gpio_power = GPIO27_HX4700_CODEC_ON,
+	.gpio_npdn  = GPIO109_HX4700_CODEC_nPDN,
+};
+
+static struct i2c_board_info i2c_board_info[] __initdata = {
+	{
+		I2C_BOARD_INFO("ak4641", 0x12),
+		.platform_data = &ak4641_info,
+	},
+};
+
+static struct platform_device audio = {
+	.name	= "hx4700-audio",
+	.id	= -1,
+};
+
+
 /*
  * PCMCIA
  */
@@ -790,6 +813,7 @@ static struct platform_device *devices[] __initdata = {
 	&gpio_vbus,
 	&power_supply,
 	&strataflash,
+	&audio,
 	&pcmcia,
 };
 
@@ -827,6 +851,7 @@ static void __init hx4700_init(void)
 	pxa_set_ficp_info(&ficp_info);
 	pxa27x_set_i2c_power_info(NULL);
 	pxa_set_i2c_info(NULL);
+	i2c_register_board_info(0, ARRAY_AND_SIZE(i2c_board_info));
 	i2c_register_board_info(1, ARRAY_AND_SIZE(pi2c_board_info));
 	pxa2xx_set_spi_info(2, &pxa_ssp2_master_info);
 	spi_register_board_info(ARRAY_AND_SIZE(tsc2046_board_info));

arch/arm/mach-pxa/mfp-pxa2xx.c

@@ -226,6 +226,12 @@ static void __init pxa25x_mfp_init(void)
 {
 	int i;
 
+	/* running before pxa_gpio_probe() */
+#ifdef CONFIG_CPU_PXA26x
+	pxa_last_gpio = 89;
+#else
+	pxa_last_gpio = 84;
+#endif
 	for (i = 0; i <= pxa_last_gpio; i++)
 		gpio_desc[i].valid = 1;
 
@@ -295,6 +301,7 @@ static void __init pxa27x_mfp_init(void)
 {
 	int i, gpio;
 
+	pxa_last_gpio = 120;	/* running before pxa_gpio_probe() */
 	for (i = 0; i <= pxa_last_gpio; i++) {
 		/* skip GPIO2, 5, 6, 7, 8, they are not
 		 * valid pins allow configuration

arch/arm/mach-pxa/pxa25x.c

@@ -25,7 +25,6 @@
 #include <linux/suspend.h>
 #include <linux/syscore_ops.h>
 #include <linux/irq.h>
-#include <linux/gpio.h>
 
 #include <asm/mach/map.h>
 #include <asm/suspend.h>
@@ -209,6 +208,7 @@ static struct clk_lookup pxa25x_clkregs[] = {
 	INIT_CLKREG(&clk_pxa25x_gpio11, NULL, "GPIO11_CLK"),
 	INIT_CLKREG(&clk_pxa25x_gpio12, NULL, "GPIO12_CLK"),
 	INIT_CLKREG(&clk_pxa25x_mem, "pxa2xx-pcmcia", NULL),
+	INIT_CLKREG(&clk_dummy, "pxa-gpio", NULL),
 };
 
 static struct clk_lookup pxa25x_hwuart_clkreg =
@@ -368,7 +368,6 @@ static int __init pxa25x_init(void)
 
 		register_syscore_ops(&pxa_irq_syscore_ops);
 		register_syscore_ops(&pxa2xx_mfp_syscore_ops);
-		register_syscore_ops(&pxa_gpio_syscore_ops);
 		register_syscore_ops(&pxa2xx_clock_syscore_ops);
 
 		ret = platform_add_devices(pxa25x_devices,

arch/arm/mach-pxa/pxa27x.c

@@ -22,7 +22,6 @@
 #include <linux/io.h>
 #include <linux/irq.h>
 #include <linux/i2c/pxa-i2c.h>
-#include <linux/gpio.h>
 
 #include <asm/mach/map.h>
 #include <mach/hardware.h>
@@ -230,6 +229,7 @@ static struct clk_lookup pxa27x_clkregs[] = {
 	INIT_CLKREG(&clk_pxa27x_im, NULL, "IMCLK"),
 	INIT_CLKREG(&clk_pxa27x_memc, NULL, "MEMCLK"),
 	INIT_CLKREG(&clk_pxa27x_mem, "pxa2xx-pcmcia", NULL),
+	INIT_CLKREG(&clk_dummy, "pxa-gpio", NULL),
 };
 
 #ifdef CONFIG_PM
@@ -456,7 +456,6 @@ static int __init pxa27x_init(void)
 
 		register_syscore_ops(&pxa_irq_syscore_ops);
 		register_syscore_ops(&pxa2xx_mfp_syscore_ops);
-		register_syscore_ops(&pxa_gpio_syscore_ops);
 		register_syscore_ops(&pxa2xx_clock_syscore_ops);
 
 		ret = platform_add_devices(devices, ARRAY_SIZE(devices));

arch/arm/mach-pxa/pxa3xx.c

@@ -462,7 +462,6 @@ static int __init pxa3xx_init(void)
 
 		register_syscore_ops(&pxa_irq_syscore_ops);
 		register_syscore_ops(&pxa3xx_mfp_syscore_ops);
-		register_syscore_ops(&pxa_gpio_syscore_ops);
 		register_syscore_ops(&pxa3xx_clock_syscore_ops);
 
 		ret = platform_add_devices(devices, ARRAY_SIZE(devices));

arch/arm/mach-pxa/pxa95x.c

@@ -283,7 +283,6 @@ static int __init pxa95x_init(void)
 			return ret;
 
 		register_syscore_ops(&pxa_irq_syscore_ops);
-		register_syscore_ops(&pxa_gpio_syscore_ops);
 		register_syscore_ops(&pxa3xx_clock_syscore_ops);
 
 		ret = platform_add_devices(devices, ARRAY_SIZE(devices));

arch/arm/mach-pxa/saarb.c

@@ -15,7 +15,6 @@
 #include <linux/i2c.h>
 #include <linux/i2c/pxa-i2c.h>
 #include <linux/mfd/88pm860x.h>
-#include <linux/gpio.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>

arch/arm/mach-pxa/sharpsl_pm.c

@@ -168,6 +168,7 @@ struct battery_thresh sharpsl_battery_levels_noac[] = {
 #define MAXCTRL_SEL_SH   4
 #define MAXCTRL_STR      (1u << 7)
 
+extern int max1111_read_channel(int);
 /*
  * Read MAX1111 ADC
  */
@@ -177,8 +178,6 @@ int sharpsl_pm_pxa_read_max1111(int channel)
 	if (machine_is_tosa())
 	    return 0;
 
-	extern int max1111_read_channel(int);
-
 	/* max1111 accepts channels from 0-3, however,
 	 * it is encoded from 0-7 here in the code.
 	 */

arch/arm/mach-pxa/spitz_pm.c

@@ -172,10 +172,9 @@ static int spitz_should_wakeup(unsigned int resume_on_alarm)
 static unsigned long spitz_charger_wakeup(void)
 {
 	unsigned long ret;
-	ret = (!gpio_get_value(SPITZ_GPIO_KEY_INT)
+	ret = ((!gpio_get_value(SPITZ_GPIO_KEY_INT)
 		<< GPIO_bit(SPITZ_GPIO_KEY_INT))
-		| (!gpio_get_value(SPITZ_GPIO_SYNC)
-		<< GPIO_bit(SPITZ_GPIO_SYNC));
+		| gpio_get_value(SPITZ_GPIO_SYNC));
 	return ret;
 }
 

arch/arm/mach-s3c2440/common.h

@@ -12,6 +12,6 @@
 #ifndef __ARCH_ARM_MACH_S3C2440_COMMON_H
 #define __ARCH_ARM_MACH_S3C2440_COMMON_H
 
-void s3c2440_restart(char mode, const char *cmd);
+void s3c244x_restart(char mode, const char *cmd);
 
 #endif /* __ARCH_ARM_MACH_S3C2440_COMMON_H */

arch/arm/mach-s3c2440/mach-anubis.c

@@ -487,5 +487,5 @@ MACHINE_START(ANUBIS, "Simtec-Anubis")
 	.init_machine	= anubis_init,
 	.init_irq	= s3c24xx_init_irq,
 	.timer		= &s3c24xx_timer,
-	.restart	= s3c2440_restart,
+	.restart	= s3c244x_restart,
 MACHINE_END

arch/arm/mach-s3c2440/mach-at2440evb.c

@@ -222,5 +222,5 @@ MACHINE_START(AT2440EVB, "AT2440EVB")
 	.init_machine	= at2440evb_init,
 	.init_irq	= s3c24xx_init_irq,
 	.timer		= &s3c24xx_timer,
-	.restart	= s3c2440_restart,
+	.restart	= s3c244x_restart,
 MACHINE_END

arch/arm/mach-s3c2440/mach-gta02.c

@@ -601,5 +601,5 @@ MACHINE_START(NEO1973_GTA02, "GTA02")
 	.init_irq	= s3c24xx_init_irq,
 	.init_machine	= gta02_machine_init,
 	.timer		= &s3c24xx_timer,
-	.restart	= s3c2440_restart,
+	.restart	= s3c244x_restart,
 MACHINE_END

arch/arm/mach-s3c2440/mach-mini2440.c

@@ -701,5 +701,5 @@ MACHINE_START(MINI2440, "MINI2440")
 	.init_machine	= mini2440_init,
 	.init_irq	= s3c24xx_init_irq,
 	.timer		= &s3c24xx_timer,
-	.restart	= s3c2440_restart,
+	.restart	= s3c244x_restart,
 MACHINE_END

arch/arm/mach-s3c2440/mach-nexcoder.c

@@ -158,5 +158,5 @@ MACHINE_START(NEXCODER_2440, "NexVision - Nexcoder 2440")
 	.init_machine	= nexcoder_init,
 	.init_irq	= s3c24xx_init_irq,
 	.timer		= &s3c24xx_timer,
-	.restart	= s3c2440_restart,
+	.restart	= s3c244x_restart,
 MACHINE_END

arch/arm/mach-s3c2440/mach-osiris.c

@@ -436,5 +436,5 @@ MACHINE_START(OSIRIS, "Simtec-OSIRIS")
 	.init_irq	= s3c24xx_init_irq,
 	.init_machine	= osiris_init,
 	.timer		= &s3c24xx_timer,
-	.restart	= s3c2440_restart,
+	.restart	= s3c244x_restart,
 MACHINE_END

arch/arm/mach-s3c2440/mach-rx1950.c

@@ -822,5 +822,5 @@ MACHINE_START(RX1950, "HP iPAQ RX1950")
 	.init_irq = s3c24xx_init_irq,
 	.init_machine = rx1950_init_machine,
 	.timer = &s3c24xx_timer,
-	.restart	= s3c2440_restart,
+	.restart	= s3c244x_restart,
 MACHINE_END

arch/arm/mach-s3c2440/mach-rx3715.c

@@ -213,5 +213,5 @@ MACHINE_START(RX3715, "IPAQ-RX3715")
 	.init_irq	= rx3715_init_irq,
 	.init_machine	= rx3715_init_machine,
 	.timer		= &s3c24xx_timer,
-	.restart	= s3c2440_restart,
+	.restart	= s3c244x_restart,
 MACHINE_END

arch/arm/mach-s3c2440/mach-smdk2440.c

@@ -183,5 +183,5 @@ MACHINE_START(S3C2440, "SMDK2440")
 	.map_io		= smdk2440_map_io,
 	.init_machine	= smdk2440_machine_init,
 	.timer		= &s3c24xx_timer,
-	.restart	= s3c2440_restart,
+	.restart	= s3c244x_restart,
 MACHINE_END

arch/arm/mach-s3c2440/s3c2440.c

@@ -35,7 +35,6 @@
 #include <plat/cpu.h>
 #include <plat/s3c244x.h>
 #include <plat/pm.h>
-#include <plat/watchdog-reset.h>
 
 #include <plat/gpio-core.h>
 #include <plat/gpio-cfg.h>
@@ -74,15 +73,3 @@ void __init s3c2440_map_io(void)
 	s3c24xx_gpiocfg_default.set_pull = s3c24xx_gpio_setpull_1up;
 	s3c24xx_gpiocfg_default.get_pull = s3c24xx_gpio_getpull_1up;
 }
-
-void s3c2440_restart(char mode, const char *cmd)
-{
-	if (mode == 's') {
-		soft_restart(0);
-	}
-
-	arch_wdt_reset();
-
-	/* we'll take a jump through zero as a poor second */
-	soft_restart(0);
-}

arch/arm/mach-s3c2440/s3c244x.c

@@ -46,6 +46,7 @@
 #include <plat/pm.h>
 #include <plat/pll.h>
 #include <plat/nand-core.h>
+#include <plat/watchdog-reset.h>
 
 static struct map_desc s3c244x_iodesc[] __initdata = {
 	IODESC_ENT(CLKPWR),
@@ -196,3 +197,14 @@ struct syscore_ops s3c244x_pm_syscore_ops = {
 	.suspend	= s3c244x_suspend,
 	.resume		= s3c244x_resume,
 };
+
+void s3c244x_restart(char mode, const char *cmd)
+{
+	if (mode == 's')
+		soft_restart(0);
+
+	arch_wdt_reset();
+
+	/* we'll take a jump through zero as a poor second */
+	soft_restart(0);
+}

arch/arm/mach-ux500/Kconfig

@@ -5,7 +5,7 @@ config UX500_SOC_COMMON
 	default y
 	select ARM_GIC
 	select HAS_MTU
-	select ARM_ERRATA_753970
+	select PL310_ERRATA_753970
 	select ARM_ERRATA_754322
 	select ARM_ERRATA_764369
 

arch/arm/mach-vexpress/Kconfig

@@ -7,7 +7,7 @@ config ARCH_VEXPRESS_CA9X4
 	select ARM_GIC
 	select ARM_ERRATA_720789
 	select ARM_ERRATA_751472
-	select ARM_ERRATA_753970
+	select PL310_ERRATA_753970
 	select HAVE_SMP
 	select MIGHT_HAVE_CACHE_L2X0
 

arch/arm/mm/proc-v7.S

@@ -230,9 +230,7 @@ __v7_setup:
 	mcreq	p15, 0, r10, c15, c0, 1		@ write diagnostic register
 #endif
 #ifdef CONFIG_ARM_ERRATA_743622
-	teq	r6, #0x20			@ present in r2p0
-	teqne	r6, #0x21			@ present in r2p1
-	teqne	r6, #0x22			@ present in r2p2
+	teq	r5, #0x00200000			@ only present in r2p*
 	mrceq	p15, 0, r10, c15, c0, 1		@ read diagnostic register
 	orreq	r10, r10, #1 << 6		@ set bit #6
 	mcreq	p15, 0, r10, c15, c0, 1		@ write diagnostic register

arch/arm/plat-omap/common.c

@@ -69,6 +69,7 @@ void __init omap_reserve(void)
 	omap_vram_reserve_sdram_memblock();
 	omap_dsp_reserve_sdram_memblock();
 	omap_secure_ram_reserve_memblock();
+	omap_barrier_reserve_memblock();
 }
 
 void __init omap_init_consistent_dma_size(void)

arch/arm/plat-omap/include/plat/irqs.h

@@ -428,8 +428,16 @@
 #define OMAP_GPMC_NR_IRQS	8
 #define OMAP_GPMC_IRQ_END	(OMAP_GPMC_IRQ_BASE + OMAP_GPMC_NR_IRQS)
 
+/* PRCM IRQ handler */
+#ifdef CONFIG_ARCH_OMAP2PLUS
+#define OMAP_PRCM_IRQ_BASE	(OMAP_GPMC_IRQ_END)
+#define OMAP_PRCM_NR_IRQS	64
+#define OMAP_PRCM_IRQ_END	(OMAP_PRCM_IRQ_BASE + OMAP_PRCM_NR_IRQS)
+#else
+#define OMAP_PRCM_IRQ_END	OMAP_GPMC_IRQ_END
+#endif
 
-#define NR_IRQS			OMAP_GPMC_IRQ_END
+#define NR_IRQS			OMAP_PRCM_IRQ_END
 
 #define OMAP_IRQ_BIT(irq)	(1 << ((irq) % 32))
 

arch/arm/plat-omap/include/plat/omap-secure.h

@@ -10,4 +10,10 @@ static inline void omap_secure_ram_reserve_memblock(void)
 { }
 #endif
 
+#ifdef CONFIG_OMAP4_ERRATA_I688
+extern int omap_barrier_reserve_memblock(void);
+#else
+static inline void omap_barrier_reserve_memblock(void)
+{ }
+#endif
 #endif /* __OMAP_SECURE_H__ */

arch/arm/plat-s3c24xx/dma.c

@@ -1249,7 +1249,7 @@ static void s3c2410_dma_resume(void)
 	struct s3c2410_dma_chan *cp = s3c2410_chans + dma_channels - 1;
 	int channel;
 
-	for (channel = dma_channels - 1; channel >= 0; cp++, channel--)
+	for (channel = dma_channels - 1; channel >= 0; cp--, channel--)
 		s3c2410_dma_resume_chan(cp);
 }
 

arch/arm/plat-samsung/devs.c

@@ -1409,7 +1409,7 @@ void __init s5p_ehci_set_platdata(struct s5p_ehci_platdata *pd)
 
 #ifdef CONFIG_S3C_DEV_USB_HSOTG
 static struct resource s3c_usb_hsotg_resources[] = {
-	[0] = DEFINE_RES_MEM(S3C_PA_USB_HSOTG, SZ_16K),
+	[0] = DEFINE_RES_MEM(S3C_PA_USB_HSOTG, SZ_128K),
 	[1] = DEFINE_RES_IRQ(IRQ_OTG),
 };
 

arch/arm/plat-spear/time.c

@@ -145,11 +145,13 @@ static void clockevent_set_mode(enum clock_event_mode mode,
 static int clockevent_next_event(unsigned long cycles,
 				 struct clock_event_device *clk_event_dev)
 {
-	u16 val;
+	u16 val = readw(gpt_base + CR(CLKEVT));
+
+	if (val & CTRL_ENABLE)
+		writew(val & ~CTRL_ENABLE, gpt_base + CR(CLKEVT));
 
 	writew(cycles, gpt_base + LOAD(CLKEVT));
 
-	val = readw(gpt_base + CR(CLKEVT));
 	val |= CTRL_ENABLE | CTRL_INT_ENABLE;
 	writew(val, gpt_base + CR(CLKEVT));
 

arch/c6x/include/asm/processor.h

@@ -122,8 +122,8 @@ extern int kernel_thread(int (*fn)(void *), void * arg, unsigned long flags);
 
 extern unsigned long get_wchan(struct task_struct *p);
 
-#define KSTK_EIP(tsk)	(task_pt_regs(task)->pc)
-#define	KSTK_ESP(tsk)	(task_pt_regs(task)->sp)
+#define KSTK_EIP(task)	(task_pt_regs(task)->pc)
+#define KSTK_ESP(task)	(task_pt_regs(task)->sp)
 
 #define cpu_relax()		do { } while (0)
 

arch/mips/alchemy/common/time.c

@@ -146,7 +146,7 @@ static int __init alchemy_time_init(unsigned int m2int)
 	cd->shift = 32;
 	cd->mult = div_sc(32768, NSEC_PER_SEC, cd->shift);
 	cd->max_delta_ns = clockevent_delta2ns(0xffffffff, cd);
-	cd->min_delta_ns = clockevent_delta2ns(8, cd);	/* ~0.25ms */
+	cd->min_delta_ns = clockevent_delta2ns(9, cd);	/* ~0.28ms */
 	clockevents_register_device(cd);
 	setup_irq(m2int, &au1x_rtcmatch2_irqaction);
 

arch/mips/ath79/dev-wmac.c

@@ -96,7 +96,7 @@ void __init ath79_register_wmac(u8 *cal_data)
 {
 	if (soc_is_ar913x())
 		ar913x_wmac_setup();
-	if (soc_is_ar933x())
+	else if (soc_is_ar933x())
 		ar933x_wmac_setup();
 	else
 		BUG();

arch/mips/configs/nlm_xlp_defconfig

@@ -8,7 +8,7 @@ CONFIG_HIGH_RES_TIMERS=y
 # CONFIG_SECCOMP is not set
 CONFIG_USE_OF=y
 CONFIG_EXPERIMENTAL=y
-CONFIG_CROSS_COMPILE="mips-linux-gnu-"
+CONFIG_CROSS_COMPILE=""
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
@@ -22,7 +22,7 @@ CONFIG_AUDIT=y
 CONFIG_CGROUPS=y
 CONFIG_NAMESPACES=y
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_INITRAMFS_SOURCE="usr/dev_file_list usr/rootfs.xlp"
+CONFIG_INITRAMFS_SOURCE=""
 CONFIG_RD_BZIP2=y
 CONFIG_RD_LZMA=y
 CONFIG_INITRAMFS_COMPRESSION_LZMA=y

arch/mips/configs/nlm_xlr_defconfig

@@ -8,7 +8,7 @@ CONFIG_HIGH_RES_TIMERS=y
 CONFIG_PREEMPT_VOLUNTARY=y
 CONFIG_KEXEC=y
 CONFIG_EXPERIMENTAL=y
-CONFIG_CROSS_COMPILE="mips-linux-gnu-"
+CONFIG_CROSS_COMPILE=""
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
@@ -22,7 +22,7 @@ CONFIG_AUDIT=y
 CONFIG_NAMESPACES=y
 CONFIG_SCHED_AUTOGROUP=y
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_INITRAMFS_SOURCE="usr/dev_file_list usr/rootfs.xlr"
+CONFIG_INITRAMFS_SOURCE=""
 CONFIG_RD_BZIP2=y
 CONFIG_RD_LZMA=y
 CONFIG_INITRAMFS_COMPRESSION_GZIP=y

arch/mips/configs/powertv_defconfig

@@ -6,7 +6,7 @@ CONFIG_HZ_1000=y
 CONFIG_PREEMPT=y
 # CONFIG_SECCOMP is not set
 CONFIG_EXPERIMENTAL=y
-CONFIG_CROSS_COMPILE="mips-linux-"
+CONFIG_CROSS_COMPILE=""
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=16

arch/mips/include/asm/mach-au1x00/gpio-au1300.h

@@ -11,6 +11,9 @@
 #include <asm/io.h>
 #include <asm/mach-au1x00/au1000.h>
 
+struct gpio;
+struct gpio_chip;
+
 /* with the current GPIC design, up to 128 GPIOs are possible.
  * The only implementation so far is in the Au1300, which has 75 externally
  * available GPIOs.
@@ -203,7 +206,22 @@ static inline int gpio_request(unsigned int gpio, const char *label)
 	return 0;
 }
 
-static inline void gpio_free(unsigned int gpio)
+static inline int gpio_request_one(unsigned gpio,
+					unsigned long flags, const char *label)
+{
+	return 0;
+}
+
+static inline int gpio_request_array(struct gpio *array, size_t num)
+{
+	return 0;
+}
+
+static inline void gpio_free(unsigned gpio)
+{
+}
+
+static inline void gpio_free_array(struct gpio *array, size_t num)
 {
 }
 

arch/mips/include/asm/page.h

@@ -39,9 +39,6 @@
 #define HPAGE_MASK	(~(HPAGE_SIZE - 1))
 #define HUGETLB_PAGE_ORDER	(HPAGE_SHIFT - PAGE_SHIFT)
 #else /* !CONFIG_HUGETLB_PAGE */
-# ifndef BUILD_BUG
-#  define BUILD_BUG() do { extern void __build_bug(void); __build_bug(); } while (0)
-# endif
 #define HPAGE_SHIFT	({BUILD_BUG(); 0; })
 #define HPAGE_SIZE	({BUILD_BUG(); 0; })
 #define HPAGE_MASK	({BUILD_BUG(); 0; })

arch/mips/kernel/smp-bmips.c

@@ -8,7 +8,6 @@
  * SMP support for BMIPS
  */
 
-#include <linux/version.h>
 #include <linux/init.h>
 #include <linux/sched.h>
 #include <linux/mm.h>

arch/mips/kernel/traps.c

@@ -1135,7 +1135,7 @@ asmlinkage void do_mt(struct pt_regs *regs)
 		printk(KERN_DEBUG "YIELD Scheduler Exception\n");
 		break;
 	case 5:
-		printk(KERN_DEBUG "Gating Storage Schedulier Exception\n");
+		printk(KERN_DEBUG "Gating Storage Scheduler Exception\n");
 		break;
 	default:
 		printk(KERN_DEBUG "*** UNKNOWN THREAD EXCEPTION %d ***\n",

arch/mips/kernel/vmlinux.lds.S

@@ -69,7 +69,6 @@ SECTIONS
 	RODATA
 
 	/* writeable */
-	_sdata = .;				/* Start of data section */
 	.data : {	/* Data */
 		. = . + DATAOFFSET;		/* for CONFIG_MAPPED_KERNEL */
 

arch/mips/mm/fault.c

@@ -42,6 +42,8 @@ asmlinkage void __kprobes do_page_fault(struct pt_regs *regs, unsigned long writ
 	const int field = sizeof(unsigned long) * 2;
 	siginfo_t info;
 	int fault;
+	unsigned int flags = FAULT_FLAG_ALLOW_RETRY | FAULT_FLAG_KILLABLE |
+						 (write ? FAULT_FLAG_WRITE : 0);
 
 #if 0
 	printk("Cpu%d[%s:%d:%0*lx:%ld:%0*lx]\n", raw_smp_processor_id(),
@@ -91,6 +93,7 @@ asmlinkage void __kprobes do_page_fault(struct pt_regs *regs, unsigned long writ
 	if (in_atomic() || !mm)
 		goto bad_area_nosemaphore;
 
+retry:
 	down_read(&mm->mmap_sem);
 	vma = find_vma(mm, address);
 	if (!vma)
@@ -144,7 +147,11 @@ asmlinkage void __kprobes do_page_fault(struct pt_regs *regs, unsigned long writ
 	 * make sure we exit gracefully rather than endlessly redo
 	 * the fault.
 	 */
-	fault = handle_mm_fault(mm, vma, address, write ? FAULT_FLAG_WRITE : 0);
+	fault = handle_mm_fault(mm, vma, address, flags);
+
+	if ((fault & VM_FAULT_RETRY) && fatal_signal_pending(current))
+		return;
+
 	perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS, 1, regs, address);
 	if (unlikely(fault & VM_FAULT_ERROR)) {
 		if (fault & VM_FAULT_OOM)
@@ -153,12 +160,27 @@ asmlinkage void __kprobes do_page_fault(struct pt_regs *regs, unsigned long writ
 			goto do_sigbus;
 		BUG();
 	}
-	if (fault & VM_FAULT_MAJOR) {
-		perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS_MAJ, 1, regs, address);
-		tsk->maj_flt++;
-	} else {
-		perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS_MIN, 1, regs, address);
-		tsk->min_flt++;
+	if (flags & FAULT_FLAG_ALLOW_RETRY) {
+		if (fault & VM_FAULT_MAJOR) {
+			perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS_MAJ, 1,
+						  regs, address);
+			tsk->maj_flt++;
+		} else {
+			perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS_MIN, 1,
+						  regs, address);
+			tsk->min_flt++;
+		}
+		if (fault & VM_FAULT_RETRY) {
+			flags &= ~FAULT_FLAG_ALLOW_RETRY;
+
+			/*
+			 * No need to up_read(&mm->mmap_sem) as we would
+			 * have already released it in __lock_page_or_retry
+			 * in mm/filemap.c.
+			 */
+
+			goto retry;
+		}
 	}
 
 	up_read(&mm->mmap_sem);

arch/mips/pci/pci.c

@@ -279,7 +279,6 @@ void __devinit pcibios_fixup_bus(struct pci_bus *bus)
 {
 	/* Propagate hose info into the subordinate devices.  */
 
-	struct list_head *ln;
 	struct pci_dev *dev = bus->self;
 
 	if (pci_probe_only && dev &&
@@ -288,9 +287,7 @@ void __devinit pcibios_fixup_bus(struct pci_bus *bus)
 		pcibios_fixup_device_resources(dev, bus);
 	}
 
-	for (ln = bus->devices.next; ln != &bus->devices; ln = ln->next) {
-		dev = pci_dev_b(ln);
-
+	list_for_each_entry(dev, &bus->devices, bus_list) {
 		if ((dev->class >> 8) != PCI_CLASS_BRIDGE_PCI)
 			pcibios_fixup_device_resources(dev, bus);
 	}

arch/mips/pmc-sierra/yosemite/ht-irq.c

@@ -35,16 +35,6 @@
  */
 void __init titan_ht_pcibios_fixup_bus(struct pci_bus *bus)
 {
-	struct pci_bus *current_bus = bus;
-	struct pci_dev *devices;
-	struct list_head *devices_link;
-
-	list_for_each(devices_link, &(current_bus->devices)) {
-		devices = pci_dev_b(devices_link);
-		if (devices == NULL)
-			continue;
-	}
-
 	/*
 	 * PLX and SPKT related changes go here
 	 */

arch/mips/txx9/generic/7segled.c

@@ -102,7 +102,7 @@ static int __init tx_7segled_init_sysfs(void)
 			break;
 		}
 		dev->id = i;
-		dev->dev = &tx_7segled_subsys;
+		dev->bus = &tx_7segled_subsys;
 		error = device_register(dev);
 		if (!error) {
 			device_create_file(dev, &dev_attr_ascii);

arch/openrisc/include/asm/ptrace.h

@@ -77,7 +77,6 @@ struct pt_regs {
 	long  syscallno;	/* Syscall number (used by strace) */
 	long dummy;		/* Cheap alignment fix */
 };
-#endif /* __ASSEMBLY__ */
 
 /* TODO: Rename this to REDZONE because that's what it is */
 #define STACK_FRAME_OVERHEAD  128  /* size of minimum stack frame */
@@ -87,6 +86,13 @@ struct pt_regs {
 #define user_stack_pointer(regs)	((unsigned long)(regs)->sp)
 #define profile_pc(regs)		instruction_pointer(regs)
 
+static inline long regs_return_value(struct pt_regs *regs)
+{
+	return regs->gpr[11];
+}
+
+#endif /* __ASSEMBLY__ */
+
 /*
  * Offsets used by 'ptrace' system call interface.
  */

arch/openrisc/kernel/init_task.c

@@ -17,6 +17,7 @@
 
 #include <linux/init_task.h>
 #include <linux/mqueue.h>
+#include <linux/export.h>
 
 static struct signal_struct init_signals = INIT_SIGNALS(init_signals);
 static struct sighand_struct init_sighand = INIT_SIGHAND(init_sighand);

arch/openrisc/kernel/irq.c

@@ -23,6 +23,7 @@
 #include <linux/irq.h>
 #include <linux/seq_file.h>
 #include <linux/kernel_stat.h>
+#include <linux/export.h>
 
 #include <linux/irqflags.h>
 

arch/openrisc/kernel/ptrace.c

@@ -188,11 +188,9 @@ asmlinkage long do_syscall_trace_enter(struct pt_regs *regs)
 		 */
 		ret = -1L;
 
-	/* Are these regs right??? */
-	if (unlikely(current->audit_context))
-		audit_syscall_entry(audit_arch(), regs->syscallno,
-				    regs->gpr[3], regs->gpr[4],
-				    regs->gpr[5], regs->gpr[6]);
+	audit_syscall_entry(audit_arch(), regs->syscallno,
+			    regs->gpr[3], regs->gpr[4],
+			    regs->gpr[5], regs->gpr[6]);
 
 	return ret ? : regs->syscallno;
 }
@@ -201,9 +199,7 @@ asmlinkage void do_syscall_trace_leave(struct pt_regs *regs)
 {
 	int step;
 
-	if (unlikely(current->audit_context))
-		audit_syscall_exit(AUDITSC_RESULT(regs->gpr[11]),
-				   regs->gpr[11]);
+	audit_syscall_exit(regs);
 
 	step = test_thread_flag(TIF_SINGLESTEP);
 	if (step || test_thread_flag(TIF_SYSCALL_TRACE))

arch/parisc/Makefile

@@ -31,7 +31,11 @@ ifdef CONFIG_64BIT
 UTS_MACHINE	:= parisc64
 CHECKFLAGS	+= -D__LP64__=1 -m64
 WIDTH		:= 64
+
+# FIXME: if no default set, should really try to locate dynamically
+ifeq ($(CROSS_COMPILE),)
 CROSS_COMPILE	:= hppa64-linux-gnu-
+endif
 else # 32-bit
 WIDTH		:=
 endif

arch/s390/Kconfig

@@ -227,6 +227,9 @@ config COMPAT
 config SYSVIPC_COMPAT
 	def_bool y if COMPAT && SYSVIPC
 
+config KEYS_COMPAT
+	def_bool y if COMPAT && KEYS
+
 config AUDIT_ARCH
 	def_bool y
 

arch/s390/kernel/crash_dump.c

@@ -11,7 +11,6 @@
 #include <linux/module.h>
 #include <linux/gfp.h>
 #include <linux/slab.h>
-#include <linux/crash_dump.h>
 #include <linux/bootmem.h>
 #include <linux/elf.h>
 #include <asm/ipl.h>

arch/s390/mm/init.c

@@ -223,16 +223,38 @@ void free_initrd_mem(unsigned long start, unsigned long end)
 #ifdef CONFIG_MEMORY_HOTPLUG
 int arch_add_memory(int nid, u64 start, u64 size)
 {
-	struct pglist_data *pgdat;
+	unsigned long zone_start_pfn, zone_end_pfn, nr_pages;
+	unsigned long start_pfn = PFN_DOWN(start);
+	unsigned long size_pages = PFN_DOWN(size);
 	struct zone *zone;
 	int rc;
 
-	pgdat = NODE_DATA(nid);
-	zone = pgdat->node_zones + ZONE_MOVABLE;
 	rc = vmem_add_mapping(start, size);
 	if (rc)
 		return rc;
-	rc = __add_pages(nid, zone, PFN_DOWN(start), PFN_DOWN(size));
+	for_each_zone(zone) {
+		if (zone_idx(zone) != ZONE_MOVABLE) {
+			/* Add range within existing zone limits */
+			zone_start_pfn = zone->zone_start_pfn;
+			zone_end_pfn = zone->zone_start_pfn +
+				       zone->spanned_pages;
+		} else {
+			/* Add remaining range to ZONE_MOVABLE */
+			zone_start_pfn = start_pfn;
+			zone_end_pfn = start_pfn + size_pages;
+		}
+		if (start_pfn < zone_start_pfn || start_pfn >= zone_end_pfn)
+			continue;
+		nr_pages = (start_pfn + size_pages > zone_end_pfn) ?
+			   zone_end_pfn - start_pfn : size_pages;
+		rc = __add_pages(nid, zone, start_pfn, nr_pages);
+		if (rc)
+			break;
+		start_pfn += nr_pages;
+		size_pages -= nr_pages;
+		if (!size_pages)
+			break;
+	}
 	if (rc)
 		vmem_remove_mapping(start, size);
 	return rc;

arch/x86/ia32/ia32_aout.c

@@ -315,6 +315,13 @@ static int load_aout_binary(struct linux_binprm *bprm, struct pt_regs *regs)
 	current->mm->free_area_cache = TASK_UNMAPPED_BASE;
 	current->mm->cached_hole_size = 0;
 
+	retval = setup_arg_pages(bprm, IA32_STACK_TOP, EXSTACK_DEFAULT);
+	if (retval < 0) {
+		/* Someone check-me: is this error path enough? */
+		send_sig(SIGKILL, current, 0);
+		return retval;
+	}
+
 	install_exec_creds(bprm);
 	current->flags &= ~PF_FORKNOEXEC;
 
@@ -410,13 +417,6 @@ static int load_aout_binary(struct linux_binprm *bprm, struct pt_regs *regs)
 
 	set_brk(current->mm->start_brk, current->mm->brk);
 
-	retval = setup_arg_pages(bprm, IA32_STACK_TOP, EXSTACK_DEFAULT);
-	if (retval < 0) {
-		/* Someone check-me: is this error path enough? */
-		send_sig(SIGKILL, current, 0);
-		return retval;
-	}
-
 	current->mm->start_stack =
 		(unsigned long)create_aout_tables((char __user *)bprm->p, bprm);
 	/* start thread */

arch/x86/include/asm/perf_event.h

@@ -242,4 +242,12 @@ static inline void perf_get_x86_pmu_capability(struct x86_pmu_capability *cap)
 static inline void perf_events_lapic_init(void)	{ }
 #endif
 
+#if defined(CONFIG_PERF_EVENTS) && defined(CONFIG_CPU_SUP_AMD)
+ extern void amd_pmu_enable_virt(void);
+ extern void amd_pmu_disable_virt(void);
+#else
+ static inline void amd_pmu_enable_virt(void) { }
+ static inline void amd_pmu_disable_virt(void) { }
+#endif
+
 #endif /* _ASM_X86_PERF_EVENT_H */

arch/x86/kernel/cpu/perf_event.h

@@ -147,7 +147,9 @@ struct cpu_hw_events {
 	/*
 	 * AMD specific bits
 	 */
-	struct amd_nb		*amd_nb;
+	struct amd_nb			*amd_nb;
+	/* Inverted mask of bits to clear in the perf_ctr ctrl registers */
+	u64				perf_ctr_virt_mask;
 
 	void				*kfree_on_online;
 };
@@ -417,9 +419,11 @@ void x86_pmu_disable_all(void);
 static inline void __x86_pmu_enable_event(struct hw_perf_event *hwc,
 					  u64 enable_mask)
 {
+	u64 disable_mask = __this_cpu_read(cpu_hw_events.perf_ctr_virt_mask);
+
 	if (hwc->extra_reg.reg)
 		wrmsrl(hwc->extra_reg.reg, hwc->extra_reg.config);
-	wrmsrl(hwc->config_base, hwc->config | enable_mask);
+	wrmsrl(hwc->config_base, (hwc->config | enable_mask) & ~disable_mask);
 }
 
 void x86_pmu_enable_all(int added);