Merge remote-tracking branches 'regulator/topic/mt6311',...

Merge remote-tracking branches 'regulator/topic/mt6311', 'regulator/topic/ocp', 'regulator/topic/owner', 'regulator/topic/pfuze100' and 'regulator/topic/pwm' into regulator-next

Documentation/devicetree/bindings/regulator/mt6311-regulator.txt

+Mediatek MT6311 Regulator Driver
+
+Required properties:
+- compatible: "mediatek,mt6311-regulator"
+- reg: I2C slave address, usually 0x6b.
+- regulators: List of regulators provided by this controller. It is named
+  to VDVFS and VBIASN.
+  The definition for each of these nodes is defined using the standard binding
+  for regulators at Documentation/devicetree/bindings/regulator/regulator.txt.
+
+The valid names for regulators are:
+BUCK:
+  VDVFS
+LDO:
+  VBIASN
+
+Example:
+	mt6311: pmic@6b {
+		compatible = "mediatek,mt6311-regulator";
+		reg = <0x6b>;
+
+		regulators {
+			mt6311_vcpu_reg: VDVFS {
+				regulator-name = "VDVFS";
+				regulator-min-microvolt = < 600000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-ramp-delay = <10000>;
+			};
+			mt6311_ldo_reg: VBIASN {
+				regulator-name = "VBIASN";
+				regulator-min-microvolt = <200000>;
+				regulator-max-microvolt = <800000>;
+			};
+		};
+	};

Documentation/devicetree/bindings/regulator/pwm-regulator.txt

-pwm regulator bindings
+Bindings for the Generic PWM Regulator
+======================================
+
+Currently supports 2 modes of operation:
+
+Voltage Table:		When in this mode, a voltage table (See below) of
+			predefined voltage <=> duty-cycle values must be
+			provided via DT. Limitations are that the regulator can
+			only operate at the voltages supplied in the table.
+			Intermediary duty-cycle values which would normally
+			allow finer grained voltage selection are ignored and
+			rendered useless.  Although more control is given to
+			the user if the assumptions made in continuous-voltage
+			mode do not reign true.
+
+Continuous Voltage:	This mode uses the regulator's maximum and minimum
+			supplied voltages specified in the
+			regulator-{min,max}-microvolt properties to calculate
+			appropriate duty-cycle values.  This allows for a much
+			more fine grained solution when compared with
+			voltage-table mode above.  This solution does make an
+			assumption that a %50 duty-cycle value will cause the
+			regulator voltage to run at half way between the
+			supplied max_uV and min_uV values.
 
 Required properties:
-- compatible: Should be "pwm-regulator"
-- pwms: OF device-tree PWM specification (see PWM binding pwm.txt)
-- voltage-table: voltage and duty table, include 2 members in each set of
-  brackets, first one is voltage(unit: uv), the next is duty(unit: percent)
+--------------------
+- compatible:		Should be "pwm-regulator"
+
+- pwms:			PWM specification (See: ../pwm/pwm.txt)
+
+Only required for Voltage Table Mode:
+- voltage-table: 	Voltage and Duty-Cycle table consisting of 2 cells
+			    First cell is voltage in microvolts (uV)
+			    Second cell is duty-cycle in percent (%)
+
+NB: To be clear, if voltage-table is provided, then the device will be used
+in Voltage Table Mode.  If no voltage-table is provided, then the device will
+be used in Continuous Voltage Mode.
 
-Any property defined as part of the core regulator binding defined in
-regulator.txt can also be used.
+Any property defined as part of the core regulator binding can also be used.
+(See: ../regulator/regulator.txt)
 
-Example:
+Continuous Voltage Example:
 	pwm_regulator {
 		compatible = "pwm-regulator;
 		pwms = <&pwm1 0 8448 0>;
+		regulator-min-microvolt = <1016000>;
+		regulator-max-microvolt = <1114000>;
+		regulator-name = "vdd_logic";
+	};
 
+Voltage Table Example:
+	pwm_regulator {
+		compatible = "pwm-regulator;
+		pwms = <&pwm1 0 8448 0>;
+		regulator-min-microvolt = <1016000>;
+		regulator-max-microvolt = <1114000>;
+		regulator-name = "vdd_logic";
+
+			      /* Voltage Duty-Cycle */
 		voltage-table = <1114000 0>,
 				<1095000 10>,
 				<1076000 20>,
 				<1056000 30>,
 				<1036000 40>,
 				<1016000 50>;
-
-		regulator-min-microvolt = <1016000>;
-		regulator-max-microvolt = <1114000>;
-		regulator-name = "vdd_logic";
 	};

Documentation/devicetree/bindings/regulator/regulator.txt

@@ -42,6 +42,7 @@ Optional properties:
 - regulator-system-load: Load in uA present on regulator that is not captured by
   any consumer request.
 - regulator-pull-down: Enable pull down resistor when the regulator is disabled.
+- regulator-over-current-protection: Enable over current protection.
 
 Deprecated properties:
 - regulator-compatible: If a regulator chip contains multiple

drivers/regulator/Kconfig

@@ -443,6 +443,15 @@ config REGULATOR_MC13892
 	  Say y here to support the regulators found on the Freescale MC13892
 	  PMIC.
 
+config REGULATOR_MT6311
+	tristate "MediaTek MT6311 PMIC"
+	depends on I2C
+	help
+	  Say y here to select this option to enable the power regulator of
+	  MediaTek MT6311 PMIC.
+	  This driver supports the control of different power rails of device
+	  through regulator interface.
+
 config REGULATOR_MT6397
 	tristate "MediaTek MT6397 PMIC"
 	depends on MFD_MT6397

drivers/regulator/Makefile

@@ -59,6 +59,7 @@ obj-$(CONFIG_REGULATOR_MAX77802) += max77802.o
 obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o
 obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
 obj-$(CONFIG_REGULATOR_MC13XXX_CORE) +=  mc13xxx-regulator-core.o
+obj-$(CONFIG_REGULATOR_MT6311) += mt6311-regulator.o
 obj-$(CONFIG_REGULATOR_MT6397)	+= mt6397-regulator.o
 obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o
 obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o

drivers/regulator/act8865-regulator.c

@@ -530,7 +530,6 @@ MODULE_DEVICE_TABLE(i2c, act8865_ids);
 static struct i2c_driver act8865_pmic_driver = {
 	.driver	= {
 		.name	= "act8865",
-		.owner	= THIS_MODULE,
 	},
 	.probe		= act8865_pmic_probe,
 	.id_table	= act8865_ids,

drivers/regulator/core.c

@@ -1091,6 +1091,15 @@ static int set_machine_constraints(struct regulator_dev *rdev,
 		}
 	}
 
+	if (rdev->constraints->over_current_protection
+		&& ops->set_over_current_protection) {
+		ret = ops->set_over_current_protection(rdev);
+		if (ret < 0) {
+			rdev_err(rdev, "failed to set over current protection\n");
+			goto out;
+		}
+	}
+
 	print_constraints(rdev);
 	return 0;
 out:

drivers/regulator/da9210-regulator.c

@@ -259,7 +259,6 @@ MODULE_DEVICE_TABLE(i2c, da9210_i2c_id);
 static struct i2c_driver da9210_regulator_driver = {
 	.driver = {
 		.name = "da9210",
-		.owner = THIS_MODULE,
 	},
 	.probe = da9210_i2c_probe,
 	.id_table = da9210_i2c_id,

drivers/regulator/da9211-regulator.c

@@ -512,7 +512,6 @@ MODULE_DEVICE_TABLE(of, da9211_dt_ids);
 static struct i2c_driver da9211_regulator_driver = {
 	.driver = {
 		.name = "da9211",
-		.owner = THIS_MODULE,
 		.of_match_table = of_match_ptr(da9211_dt_ids),
 	},
 	.probe = da9211_i2c_probe,

drivers/regulator/isl6271a-regulator.c

@@ -156,7 +156,6 @@ MODULE_DEVICE_TABLE(i2c, isl6271a_id);
 static struct i2c_driver isl6271a_i2c_driver = {
 	.driver = {
 		.name = "isl6271a",
-		.owner = THIS_MODULE,
 	},
 	.probe = isl6271a_probe,
 	.id_table = isl6271a_id,

drivers/regulator/isl9305.c

@@ -196,7 +196,6 @@ MODULE_DEVICE_TABLE(i2c, isl9305_i2c_id);
 static struct i2c_driver isl9305_regulator_driver = {
 	.driver = {
 		.name = "isl9305",
-		.owner = THIS_MODULE,
 		.of_match_table	= of_match_ptr(isl9305_dt_ids),
 	},
 	.probe = isl9305_i2c_probe,

drivers/regulator/lp3971.c

@@ -452,7 +452,6 @@ MODULE_DEVICE_TABLE(i2c, lp3971_i2c_id);
 static struct i2c_driver lp3971_i2c_driver = {
 	.driver = {
 		.name = "LP3971",
-		.owner = THIS_MODULE,
 	},
 	.probe    = lp3971_i2c_probe,
 	.id_table = lp3971_i2c_id,

drivers/regulator/lp3972.c

@@ -550,7 +550,6 @@ MODULE_DEVICE_TABLE(i2c, lp3972_i2c_id);
 static struct i2c_driver lp3972_i2c_driver = {
 	.driver = {
 		.name = "lp3972",
-		.owner = THIS_MODULE,
 	},
 	.probe    = lp3972_i2c_probe,
 	.id_table = lp3972_i2c_id,

drivers/regulator/lp872x.c

@@ -961,7 +961,6 @@ MODULE_DEVICE_TABLE(i2c, lp872x_ids);
 static struct i2c_driver lp872x_driver = {
 	.driver = {
 		.name = "lp872x",
-		.owner = THIS_MODULE,
 		.of_match_table = of_match_ptr(lp872x_dt_ids),
 	},
 	.probe = lp872x_probe,

drivers/regulator/ltc3589.c

@@ -542,7 +542,6 @@ MODULE_DEVICE_TABLE(i2c, ltc3589_i2c_id);
 static struct i2c_driver ltc3589_driver = {
 	.driver = {
 		.name = DRIVER_NAME,
-		.owner = THIS_MODULE,
 	},
 	.probe = ltc3589_probe,
 	.id_table = ltc3589_i2c_id,

drivers/regulator/max1586.c

@@ -304,7 +304,6 @@ static struct i2c_driver max1586_pmic_driver = {
 	.probe = max1586_pmic_probe,
 	.driver		= {
 		.name	= "max1586",
-		.owner	= THIS_MODULE,
 		.of_match_table = of_match_ptr(max1586_of_match),
 	},
 	.id_table	= max1586_id,

drivers/regulator/max8660.c

@@ -518,7 +518,6 @@ static struct i2c_driver max8660_driver = {
 	.probe = max8660_probe,
 	.driver		= {
 		.name	= "max8660",
-		.owner	= THIS_MODULE,
 	},
 	.id_table	= max8660_id,
 };

drivers/regulator/max8973-regulator.c

@@ -732,7 +732,6 @@ static struct i2c_driver max8973_i2c_driver = {
 	.driver = {
 		.name = "max8973",
 		.of_match_table = of_max8973_match_tbl,
-		.owner = THIS_MODULE,
 	},
 	.probe = max8973_probe,
 	.id_table = max8973_id,

drivers/regulator/mt6311-regulator.c

+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Henry Chen <henryc.chen@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/regulator/mt6311.h>
+#include <linux/slab.h>
+#include "mt6311-regulator.h"
+
+static const struct regmap_config mt6311_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = MT6311_FQMTR_CON4,
+};
+
+/* Default limits measured in millivolts and milliamps */
+#define MT6311_MIN_UV		600000
+#define MT6311_MAX_UV		1393750
+#define MT6311_STEP_UV		6250
+
+static const struct regulator_linear_range buck_volt_range[] = {
+	REGULATOR_LINEAR_RANGE(MT6311_MIN_UV, 0, 0x7f, MT6311_STEP_UV),
+};
+
+static const struct regulator_ops mt6311_buck_ops = {
+	.list_voltage = regulator_list_voltage_linear_range,
+	.map_voltage = regulator_map_voltage_linear_range,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+};
+
+static const struct regulator_ops mt6311_ldo_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+};
+
+#define MT6311_BUCK(_id) \
+{\
+	.name = #_id,\
+	.ops = &mt6311_buck_ops,\
+	.of_match = of_match_ptr(#_id),\
+	.regulators_node = of_match_ptr("regulators"),\
+	.type = REGULATOR_VOLTAGE,\
+	.id = MT6311_ID_##_id,\
+	.n_voltages = (MT6311_MAX_UV - MT6311_MIN_UV) / MT6311_STEP_UV + 1,\
+	.min_uV = MT6311_MIN_UV,\
+	.uV_step = MT6311_STEP_UV,\
+	.owner = THIS_MODULE,\
+	.linear_ranges = buck_volt_range, \
+	.n_linear_ranges = ARRAY_SIZE(buck_volt_range), \
+	.enable_reg = MT6311_VDVFS11_CON9,\
+	.enable_mask = MT6311_PMIC_VDVFS11_EN_MASK,\
+	.vsel_reg = MT6311_VDVFS11_CON12,\
+	.vsel_mask = MT6311_PMIC_VDVFS11_VOSEL_MASK,\
+}
+
+#define MT6311_LDO(_id) \
+{\
+	.name = #_id,\
+	.ops = &mt6311_ldo_ops,\
+	.of_match = of_match_ptr(#_id),\
+	.regulators_node = of_match_ptr("regulators"),\
+	.type = REGULATOR_VOLTAGE,\
+	.id = MT6311_ID_##_id,\
+	.owner = THIS_MODULE,\
+	.enable_reg = MT6311_LDO_CON3,\
+	.enable_mask = MT6311_PMIC_RG_VBIASN_EN_MASK,\
+}
+
+static const struct regulator_desc mt6311_regulators[] = {
+	MT6311_BUCK(VDVFS),
+	MT6311_LDO(VBIASN),
+};
+
+/*
+ * I2C driver interface functions
+ */
+static int mt6311_i2c_probe(struct i2c_client *i2c,
+		const struct i2c_device_id *id)
+{
+	struct regulator_config config = { };
+	struct regulator_dev *rdev;
+	struct regmap *regmap;
+	int i, ret;
+	unsigned int data;
+
+	regmap = devm_regmap_init_i2c(i2c, &mt6311_regmap_config);
+	if (IS_ERR(regmap)) {
+		ret = PTR_ERR(regmap);
+		dev_err(&i2c->dev, "Failed to allocate register map: %d\n",
+			ret);
+		return ret;
+	}
+
+	ret = regmap_read(regmap, MT6311_SWCID, &data);
+	if (ret < 0) {
+		dev_err(&i2c->dev, "Failed to read DEVICE_ID reg: %d\n", ret);
+		return ret;
+	}
+
+	switch (data) {
+	case MT6311_E1_CID_CODE:
+	case MT6311_E2_CID_CODE:
+	case MT6311_E3_CID_CODE:
+		break;
+	default:
+		dev_err(&i2c->dev, "Unsupported device id = 0x%x.\n", data);
+		return -ENODEV;
+	}
+
+	for (i = 0; i < MT6311_MAX_REGULATORS; i++) {
+		config.dev = &i2c->dev;
+		config.regmap = regmap;
+
+		rdev = devm_regulator_register(&i2c->dev,
+			&mt6311_regulators[i], &config);
+		if (IS_ERR(rdev)) {
+			dev_err(&i2c->dev,
+				"Failed to register MT6311 regulator\n");
+			return PTR_ERR(rdev);
+		}
+	}
+
+	return 0;
+}
+
+static const struct i2c_device_id mt6311_i2c_id[] = {
+	{"mt6311", 0},
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, mt6311_i2c_id);
+
+#ifdef CONFIG_OF
+static const struct of_device_id mt6311_dt_ids[] = {
+	{ .compatible = "mediatek,mt6311-regulator",
+	  .data = &mt6311_i2c_id[0] },
+	{},
+};
+MODULE_DEVICE_TABLE(of, mt6311_dt_ids);
+#endif
+
+static struct i2c_driver mt6311_regulator_driver = {
+	.driver = {
+		.name = "mt6311",
+		.of_match_table = of_match_ptr(mt6311_dt_ids),
+	},
+	.probe = mt6311_i2c_probe,
+	.id_table = mt6311_i2c_id,
+};
+
+module_i2c_driver(mt6311_regulator_driver);
+
+MODULE_AUTHOR("Henry Chen <henryc.chen@mediatek.com>");
+MODULE_DESCRIPTION("Regulator device driver for Mediatek MT6311");
+MODULE_LICENSE("GPL v2");

drivers/regulator/mt6311-regulator.h

+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Henry Chen <henryc.chen@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __MT6311_REGULATOR_H__
+#define __MT6311_REGULATOR_H__
+
+#define MT6311_SWCID              0x01
+
+#define MT6311_TOP_INT_CON        0x18
+#define MT6311_TOP_INT_MON        0x19
+
+#define MT6311_VDVFS11_CON0       0x87
+#define MT6311_VDVFS11_CON7       0x88
+#define MT6311_VDVFS11_CON8       0x89
+#define MT6311_VDVFS11_CON9       0x8A
+#define MT6311_VDVFS11_CON10      0x8B
+#define MT6311_VDVFS11_CON11      0x8C
+#define MT6311_VDVFS11_CON12      0x8D
+#define MT6311_VDVFS11_CON13      0x8E
+#define MT6311_VDVFS11_CON14      0x8F
+#define MT6311_VDVFS11_CON15      0x90
+#define MT6311_VDVFS11_CON16      0x91
+#define MT6311_VDVFS11_CON17      0x92
+#define MT6311_VDVFS11_CON18      0x93
+#define MT6311_VDVFS11_CON19      0x94
+
+#define MT6311_LDO_CON0           0xCC
+#define MT6311_LDO_OCFB0          0xCD
+#define MT6311_LDO_CON2           0xCE
+#define MT6311_LDO_CON3           0xCF
+#define MT6311_LDO_CON4           0xD0
+#define MT6311_FQMTR_CON0         0xD1
+#define MT6311_FQMTR_CON1         0xD2
+#define MT6311_FQMTR_CON2         0xD3
+#define MT6311_FQMTR_CON3         0xD4
+#define MT6311_FQMTR_CON4         0xD5
+
+#define MT6311_PMIC_RG_INT_POL_MASK                      0x1
+#define MT6311_PMIC_RG_INT_EN_MASK                       0x2
+#define MT6311_PMIC_RG_BUCK_OC_INT_STATUS_MASK           0x10
+
+#define MT6311_PMIC_VDVFS11_EN_CTRL_MASK                 0x1
+#define MT6311_PMIC_VDVFS11_VOSEL_CTRL_MASK              0x2
+#define MT6311_PMIC_VDVFS11_EN_SEL_MASK                  0x3
+#define MT6311_PMIC_VDVFS11_VOSEL_SEL_MASK               0xc
+#define MT6311_PMIC_VDVFS11_EN_MASK                      0x1
+#define MT6311_PMIC_VDVFS11_VOSEL_MASK                   0x7F
+#define MT6311_PMIC_VDVFS11_VOSEL_ON_MASK                0x7F
+#define MT6311_PMIC_VDVFS11_VOSEL_SLEEP_MASK             0x7F
+#define MT6311_PMIC_NI_VDVFS11_VOSEL_MASK                0x7F
+
+#define MT6311_PMIC_RG_VBIASN_EN_MASK                    0x1
+
+#endif

drivers/regulator/of_regulator.c

@@ -107,6 +107,9 @@ static void of_get_regulation_constraints(struct device_node *np,
 	if (!of_property_read_u32(np, "regulator-system-load", &pval))
 		constraints->system_load = pval;
 
+	constraints->over_current_protection = of_property_read_bool(np,
+					"regulator-over-current-protection");
+
 	for (i = 0; i < ARRAY_SIZE(regulator_states); i++) {
 		switch (i) {
 		case PM_SUSPEND_MEM:

drivers/regulator/pfuze100-regulator.c

@@ -643,7 +643,6 @@ static struct i2c_driver pfuze_driver = {
 	.id_table = pfuze_device_id,
 	.driver = {
 		.name = "pfuze100-regulator",
-		.owner = THIS_MODULE,
 		.of_match_table = pfuze_dt_ids,
 	},
 	.probe = pfuze100_regulator_probe,
@@ -653,4 +652,3 @@ module_i2c_driver(pfuze_driver);
 MODULE_AUTHOR("Robin Gong <b38343@freescale.com>");
 MODULE_DESCRIPTION("Regulator Driver for Freescale PFUZE100/PFUZE200 PMIC");
 MODULE_LICENSE("GPL v2");
-MODULE_ALIAS("i2c:pfuze100-regulator");

drivers/regulator/pwm-regulator.c

@@ -10,6 +10,7 @@
  * published by the Free Software Foundation.
  */
 
+#include <linux/delay.h>
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/err.h>
@@ -21,9 +22,15 @@
 #include <linux/pwm.h>
 
 struct pwm_regulator_data {
-	struct pwm_voltages *duty_cycle_table;
+	/*  Shared */
 	struct pwm_device *pwm;
+
+	/* Voltage table */
+	struct pwm_voltages *duty_cycle_table;
 	int state;
+
+	/* Continuous voltage */
+	int volt_uV;
 };
 
 struct pwm_voltages {
@@ -31,6 +38,9 @@ struct pwm_voltages {
 	unsigned int dutycycle;
 };
 
+/**
+ * Voltage table call-backs
+ */
 static int pwm_regulator_get_voltage_sel(struct regulator_dev *rdev)
 {
 	struct pwm_regulator_data *drvdata = rdev_get_drvdata(rdev);
@@ -79,29 +89,129 @@ static int pwm_regulator_list_voltage(struct regulator_dev *rdev,
 	return drvdata->duty_cycle_table[selector].uV;
 }
 
-static struct regulator_ops pwm_regulator_voltage_ops = {
+/**
+ * Continuous voltage call-backs
+ */
+static int pwm_voltage_to_duty_cycle_percentage(struct regulator_dev *rdev, int req_uV)
+{
+	int min_uV = rdev->constraints->min_uV;
+	int max_uV = rdev->constraints->max_uV;
+	int diff = max_uV - min_uV;
+
+	return 100 - (((req_uV * 100) - (min_uV * 100)) / diff);
+}
+
+static int pwm_regulator_get_voltage(struct regulator_dev *rdev)
+{
+	struct pwm_regulator_data *drvdata = rdev_get_drvdata(rdev);
+
+	return drvdata->volt_uV;
+}
+
+static int pwm_regulator_set_voltage(struct regulator_dev *rdev,
+					int min_uV, int max_uV,
+					unsigned *selector)
+{
+	struct pwm_regulator_data *drvdata = rdev_get_drvdata(rdev);
+	unsigned int ramp_delay = rdev->constraints->ramp_delay;
+	unsigned int period = pwm_get_period(drvdata->pwm);
+	int duty_cycle;
+	int ret;
+
+	duty_cycle = pwm_voltage_to_duty_cycle_percentage(rdev, min_uV);
+
+	ret = pwm_config(drvdata->pwm, (period / 100) * duty_cycle, period);
+	if (ret) {
+		dev_err(&rdev->dev, "Failed to configure PWM\n");
+		return ret;
+	}
+
+	ret = pwm_enable(drvdata->pwm);
+	if (ret) {
+		dev_err(&rdev->dev, "Failed to enable PWM\n");
+		return ret;
+	}
+	drvdata->volt_uV = min_uV;
+
+	/* Delay required by PWM regulator to settle to the new voltage */
+	usleep_range(ramp_delay, ramp_delay + 1000);
+
+	return 0;
+}
+
+static struct regulator_ops pwm_regulator_voltage_table_ops = {
 	.set_voltage_sel = pwm_regulator_set_voltage_sel,
 	.get_voltage_sel = pwm_regulator_get_voltage_sel,
 	.list_voltage    = pwm_regulator_list_voltage,
 	.map_voltage     = regulator_map_voltage_iterate,
 };
 
+static struct regulator_ops pwm_regulator_voltage_continuous_ops = {
+	.get_voltage = pwm_regulator_get_voltage,
+	.set_voltage = pwm_regulator_set_voltage,
+};
+
 static struct regulator_desc pwm_regulator_desc = {
 	.name		= "pwm-regulator",
-	.ops		= &pwm_regulator_voltage_ops,
 	.type		= REGULATOR_VOLTAGE,
 	.owner		= THIS_MODULE,
 	.supply_name    = "pwm",
 };
 
+static int pwm_regulator_init_table(struct platform_device *pdev,
+				    struct pwm_regulator_data *drvdata)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct pwm_voltages *duty_cycle_table;
+	unsigned int length = 0;
+	int ret;
+
+	of_find_property(np, "voltage-table", &length);
+
+	if ((length < sizeof(*duty_cycle_table)) ||
+	    (length % sizeof(*duty_cycle_table))) {
+		dev_err(&pdev->dev,
+			"voltage-table length(%d) is invalid\n",
+			length);
+		return -EINVAL;
+	}
+
+	duty_cycle_table = devm_kzalloc(&pdev->dev, length, GFP_KERNEL);
+	if (!duty_cycle_table)
+		return -ENOMEM;
+
+	ret = of_property_read_u32_array(np, "voltage-table",
+					 (u32 *)duty_cycle_table,
+					 length / sizeof(u32));
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to read voltage-table\n");
+		return ret;
+	}
+
+	drvdata->duty_cycle_table	= duty_cycle_table;
+	pwm_regulator_desc.ops		= &pwm_regulator_voltage_table_ops;
+	pwm_regulator_desc.n_voltages	= length / sizeof(*duty_cycle_table);
+
+	return 0;
+}
+
+static int pwm_regulator_init_continuous(struct platform_device *pdev,
+					 struct pwm_regulator_data *drvdata)
+{
+	pwm_regulator_desc.ops = &pwm_regulator_voltage_continuous_ops;
+	pwm_regulator_desc.continuous_voltage_range = true;
+
+	return 0;
+}
+
 static int pwm_regulator_probe(struct platform_device *pdev)
 {
+	const struct regulator_init_data *init_data;
 	struct pwm_regulator_data *drvdata;
-	struct property *prop;
 	struct regulator_dev *regulator;
 	struct regulator_config config = { };
 	struct device_node *np = pdev->dev.of_node;
-	int length, ret;
+	int ret;
 
 	if (!np) {
 		dev_err(&pdev->dev, "Device Tree node missing\n");
@@ -112,44 +222,22 @@ static int pwm_regulator_probe(struct platform_device *pdev)
 	if (!drvdata)
 		return -ENOMEM;
 
-	/* determine the number of voltage-table */
-	prop = of_find_property(np, "voltage-table", &length);
-	if (!prop) {
-		dev_err(&pdev->dev, "No voltage-table\n");
-		return -EINVAL;
-	}
-
-	if ((length < sizeof(*drvdata->duty_cycle_table)) ||
-	    (length % sizeof(*drvdata->duty_cycle_table))) {
-		dev_err(&pdev->dev, "voltage-table length(%d) is invalid\n",
-			length);
-		return -EINVAL;
-	}
-
-	pwm_regulator_desc.n_voltages = length / sizeof(*drvdata->duty_cycle_table);
-
-	drvdata->duty_cycle_table = devm_kzalloc(&pdev->dev,
-						 length, GFP_KERNEL);
-	if (!drvdata->duty_cycle_table)
-		return -ENOMEM;
-
-	/* read voltage table from DT property */
-	ret = of_property_read_u32_array(np, "voltage-table",
-					 (u32 *)drvdata->duty_cycle_table,
-					 length / sizeof(u32));
-	if (ret < 0) {
-		dev_err(&pdev->dev, "read voltage-table failed\n");
+	if (of_find_property(np, "voltage-table", NULL))
+		ret = pwm_regulator_init_table(pdev, drvdata);
+	else
+		ret = pwm_regulator_init_continuous(pdev, drvdata);
+	if (ret)
 		return ret;
-	}
 
-	config.init_data = of_get_regulator_init_data(&pdev->dev, np,
-						      &pwm_regulator_desc);
-	if (!config.init_data)
+	init_data = of_get_regulator_init_data(&pdev->dev, np,
+					       &pwm_regulator_desc);
+	if (!init_data)
 		return -ENOMEM;
 
 	config.of_node = np;
 	config.dev = &pdev->dev;
 	config.driver_data = drvdata;
+	config.init_data = init_data;
 
 	drvdata->pwm = devm_pwm_get(&pdev->dev, NULL);
 	if (IS_ERR(drvdata->pwm)) {

drivers/regulator/tps51632-regulator.c

@@ -362,7 +362,6 @@ MODULE_DEVICE_TABLE(i2c, tps51632_id);
 static struct i2c_driver tps51632_i2c_driver = {
 	.driver = {
 		.name = "tps51632",
-		.owner = THIS_MODULE,
 		.of_match_table = of_match_ptr(tps51632_of_match),
 	},
 	.probe = tps51632_probe,

drivers/regulator/tps62360-regulator.c

@@ -515,7 +515,6 @@ MODULE_DEVICE_TABLE(i2c, tps62360_id);
 static struct i2c_driver tps62360_i2c_driver = {
 	.driver = {
 		.name = "tps62360",
-		.owner = THIS_MODULE,
 		.of_match_table = of_match_ptr(tps62360_of_match),
 	},
 	.probe = tps62360_probe,

drivers/regulator/tps65023-regulator.c

@@ -410,7 +410,6 @@ MODULE_DEVICE_TABLE(i2c, tps_65023_id);
 static struct i2c_driver tps_65023_i2c_driver = {
 	.driver = {
 		.name = "tps65023",
-		.owner = THIS_MODULE,
 	},
 	.probe = tps_65023_probe,
 	.id_table = tps_65023_id,

include/linux/regulator/driver.h

@@ -148,6 +148,7 @@ struct regulator_ops {
 	int (*get_current_limit) (struct regulator_dev *);
 
 	int (*set_input_current_limit) (struct regulator_dev *, int lim_uA);
+	int (*set_over_current_protection) (struct regulator_dev *);
 
 	/* enable/disable regulator */
 	int (*enable) (struct regulator_dev *);

include/linux/regulator/machine.h

@@ -147,6 +147,7 @@ struct regulation_constraints {
 	unsigned ramp_disable:1; /* disable ramp delay */
 	unsigned soft_start:1;	/* ramp voltage slowly */
 	unsigned pull_down:1;	/* pull down resistor when regulator off */
+	unsigned over_current_protection:1; /* auto disable on over current */
 };
 
 /**

include/linux/regulator/mt6311.h

+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Henry Chen <henryc.chen@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __LINUX_REGULATOR_MT6311_H
+#define __LINUX_REGULATOR_MT6311_H
+
+#define MT6311_MAX_REGULATORS	2
+
+enum {
+	MT6311_ID_VDVFS = 0,
+	MT6311_ID_VBIASN,
+};
+
+#define MT6311_E1_CID_CODE    0x10
+#define MT6311_E2_CID_CODE    0x20
+#define MT6311_E3_CID_CODE    0x30
+
+#endif /* __LINUX_REGULATOR_MT6311_H */