Skip to content

K
kernel_linux

OpenHarmony / kernel_linux
上一次同步 大约 4 年

通知 14
Star 8
Fork 2
K
kernel_linux
“49a7fba8485c71d0da32a31bb56ef88035a7832f”上不存在“...fluid/tests/git@gitcode.net:Crayonxin2000/Paddle.git”
提交 16b4d60b 编写于 作者: A Adrian Bunk 提交者： David S. Miller
浏览文件
操作

[IrDA]: Irport removal - part 2 

Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 e9888f54
隐藏空白更改
内联 并排
Showing with 0 addition and 2328 deletion
drivers/net/irda/act200l.c 已删除 100644 → 0
浏览文件 @ e9888f54
/*********************************************************************
*
* Filename: act200l.c
* Version: 0.8
* Description: Implementation for the ACTiSYS ACT-IR200L dongle
* Status: Experimental.
* Author: SHIMIZU Takuya <tshimizu@ga2.so-net.ne.jp>
* Created at: Fri Aug 3 17:35:42 2001
* Modified at: Fri Aug 17 10:22:40 2001
* Modified by: SHIMIZU Takuya <tshimizu@ga2.so-net.ne.jp>
*
* Copyright (c) 2001 SHIMIZU Takuya, All Rights Reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
********************************************************************/
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/tty.h>
#include <linux/init.h>
#include <net/irda/irda.h>
#include <net/irda/irda_device.h>
static int act200l_reset(struct irda_task *task);
static void act200l_open(dongle_t *self, struct qos_info *qos);
static void act200l_close(dongle_t *self);
static int act200l_change_speed(struct irda_task *task);
/* Regsiter 0: Control register #1 */
#define ACT200L_REG0 0x00
#define ACT200L_TXEN 0x01 /* Enable transmitter */
#define ACT200L_RXEN 0x02 /* Enable receiver */
/* Register 1: Control register #2 */
#define ACT200L_REG1 0x10
#define ACT200L_LODB 0x01 /* Load new baud rate count value */
#define ACT200L_WIDE 0x04 /* Expand the maximum allowable pulse */
/* Register 4: Output Power register */
#define ACT200L_REG4 0x40
#define ACT200L_OP0 0x01 /* Enable LED1C output */
#define ACT200L_OP1 0x02 /* Enable LED2C output */
#define ACT200L_BLKR 0x04
/* Register 5: Receive Mode register */
#define ACT200L_REG5 0x50
#define ACT200L_RWIDL 0x01 /* fixed 1.6us pulse mode */
/* Register 6: Receive Sensitivity register #1 */
#define ACT200L_REG6 0x60
#define ACT200L_RS0 0x01 /* receive threshold bit 0 */
#define ACT200L_RS1 0x02 /* receive threshold bit 1 */
/* Register 7: Receive Sensitivity register #2 */
#define ACT200L_REG7 0x70
#define ACT200L_ENPOS 0x04 /* Ignore the falling edge */
/* Register 8,9: Baud Rate Dvider register #1,#2 */
#define ACT200L_REG8 0x80
#define ACT200L_REG9 0x90
#define ACT200L_2400 0x5f
#define ACT200L_9600 0x17
#define ACT200L_19200 0x0b
#define ACT200L_38400 0x05
#define ACT200L_57600 0x03
#define ACT200L_115200 0x01
/* Register 13: Control register #3 */
#define ACT200L_REG13 0xd0
#define ACT200L_SHDW 0x01 /* Enable access to shadow registers */
/* Register 15: Status register */
#define ACT200L_REG15 0xf0
/* Register 21: Control register #4 */
#define ACT200L_REG21 0x50
#define ACT200L_EXCK 0x02 /* Disable clock output driver */
#define ACT200L_OSCL 0x04 /* oscillator in low power, medium accuracy mode */
static struct dongle_reg dongle = {
.type = IRDA_ACT200L_DONGLE,
.open = act200l_open,
.close = act200l_close,
.reset = act200l_reset,
.change_speed = act200l_change_speed,
.owner = THIS_MODULE,
};
static int __init act200l_init(void)
{
return irda_device_register_dongle(&dongle);
}
static void __exit act200l_cleanup(void)
{
irda_device_unregister_dongle(&dongle);
}
static void act200l_open(dongle_t *self, struct qos_info *qos)
{
IRDA_DEBUG(2, "%s()\n", __FUNCTION__ );
/* Power on the dongle */
self->set_dtr_rts(self->dev, TRUE, TRUE);
/* Set the speeds we can accept */
qos->baud_rate.bits &= IR_9600|IR_19200|IR_38400|IR_57600|IR_115200;
qos->min_turn_time.bits = 0x03;
}
static void act200l_close(dongle_t *self)
{
IRDA_DEBUG(2, "%s()\n", __FUNCTION__ );
/* Power off the dongle */
self->set_dtr_rts(self->dev, FALSE, FALSE);
}
/*
* Function act200l_change_speed (dev, speed)
*
* Set the speed for the ACTiSYS ACT-IR200L type dongle.
*
*/
static int act200l_change_speed(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
__u32 speed = (__u32) task->param;
__u8 control[3];
int ret = 0;
IRDA_DEBUG(2, "%s()\n", __FUNCTION__ );
self->speed_task = task;
switch (task->state) {
case IRDA_TASK_INIT:
if (irda_task_execute(self, act200l_reset, NULL, task,
(void *) speed))
{
/* Dongle need more time to reset */
irda_task_next_state(task, IRDA_TASK_CHILD_WAIT);
/* Give reset 1 sec to finish */
ret = msecs_to_jiffies(1000);
}
break;
case IRDA_TASK_CHILD_WAIT:
IRDA_WARNING("%s(), resetting dongle timed out!\n",
__FUNCTION__);
ret = -1;
break;
case IRDA_TASK_CHILD_DONE:
/* Clear DTR and set RTS to enter command mode */
self->set_dtr_rts(self->dev, FALSE, TRUE);
switch (speed) {
case 9600:
default:
control[0] = ACT200L_REG8 | (ACT200L_9600 & 0x0f);
control[1] = ACT200L_REG9 | ((ACT200L_9600 >> 4) & 0x0f);
break;
case 19200:
control[0] = ACT200L_REG8 | (ACT200L_19200 & 0x0f);
control[1] = ACT200L_REG9 | ((ACT200L_19200 >> 4) & 0x0f);
break;
case 38400:
control[0] = ACT200L_REG8 | (ACT200L_38400 & 0x0f);
control[1] = ACT200L_REG9 | ((ACT200L_38400 >> 4) & 0x0f);
break;
case 57600:
control[0] = ACT200L_REG8 | (ACT200L_57600 & 0x0f);
control[1] = ACT200L_REG9 | ((ACT200L_57600 >> 4) & 0x0f);
break;
case 115200:
control[0] = ACT200L_REG8 | (ACT200L_115200 & 0x0f);
control[1] = ACT200L_REG9 | ((ACT200L_115200 >> 4) & 0x0f);
break;
}
control[2] = ACT200L_REG1 | ACT200L_LODB | ACT200L_WIDE;
/* Write control bytes */
self->write(self->dev, control, 3);
irda_task_next_state(task, IRDA_TASK_WAIT);
ret = msecs_to_jiffies(5);
break;
case IRDA_TASK_WAIT:
/* Go back to normal mode */
self->set_dtr_rts(self->dev, TRUE, TRUE);
irda_task_next_state(task, IRDA_TASK_DONE);
self->speed_task = NULL;
break;
default:
IRDA_ERROR("%s(), unknown state %d\n",
__FUNCTION__, task->state);
irda_task_next_state(task, IRDA_TASK_DONE);
self->speed_task = NULL;
ret = -1;
break;
}
return ret;
}
/*
* Function act200l_reset (driver)
*
* Reset the ACTiSYS ACT-IR200L type dongle.
*/
static int act200l_reset(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
__u8 control[9] = {
ACT200L_REG15,
ACT200L_REG13 | ACT200L_SHDW,
ACT200L_REG21 | ACT200L_EXCK | ACT200L_OSCL,
ACT200L_REG13,
ACT200L_REG7 | ACT200L_ENPOS,
ACT200L_REG6 | ACT200L_RS0 | ACT200L_RS1,
ACT200L_REG5 | ACT200L_RWIDL,
ACT200L_REG4 | ACT200L_OP0 | ACT200L_OP1 | ACT200L_BLKR,
ACT200L_REG0 | ACT200L_TXEN | ACT200L_RXEN
};
int ret = 0;
IRDA_DEBUG(2, "%s()\n", __FUNCTION__ );
self->reset_task = task;
switch (task->state) {
case IRDA_TASK_INIT:
/* Power on the dongle */
self->set_dtr_rts(self->dev, TRUE, TRUE);
irda_task_next_state(task, IRDA_TASK_WAIT1);
ret = msecs_to_jiffies(50);
break;
case IRDA_TASK_WAIT1:
/* Reset the dongle : set RTS low for 25 ms */
self->set_dtr_rts(self->dev, TRUE, FALSE);
irda_task_next_state(task, IRDA_TASK_WAIT2);
ret = msecs_to_jiffies(50);
break;
case IRDA_TASK_WAIT2:
/* Clear DTR and set RTS to enter command mode */
self->set_dtr_rts(self->dev, FALSE, TRUE);
/* Write control bytes */
self->write(self->dev, control, 9);
irda_task_next_state(task, IRDA_TASK_WAIT3);
ret = msecs_to_jiffies(15);
break;
case IRDA_TASK_WAIT3:
/* Go back to normal mode */
self->set_dtr_rts(self->dev, TRUE, TRUE);
irda_task_next_state(task, IRDA_TASK_DONE);
self->reset_task = NULL;
break;
default:
IRDA_ERROR("%s(), unknown state %d\n",
__FUNCTION__, task->state);
irda_task_next_state(task, IRDA_TASK_DONE);
self->reset_task = NULL;
ret = -1;
break;
}
return ret;
}
MODULE_AUTHOR("SHIMIZU Takuya <tshimizu@ga2.so-net.ne.jp>");
MODULE_DESCRIPTION("ACTiSYS ACT-IR200L dongle driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("irda-dongle-10"); /* IRDA_ACT200L_DONGLE */
/*
* Function init_module (void)
*
* Initialize ACTiSYS ACT-IR200L module
*
*/
module_init(act200l_init);
/*
* Function cleanup_module (void)
*
* Cleanup ACTiSYS ACT-IR200L module
*
*/
module_exit(act200l_cleanup);
drivers/net/irda/actisys.c 已删除 100644 → 0
浏览文件 @ e9888f54
/*********************************************************************
*
* Filename: actisys.c
* Version: 1.0
* Description: Implementation for the ACTiSYS IR-220L and IR-220L+
* dongles
* Status: Beta.
* Authors: Dag Brattli <dagb@cs.uit.no> (initially)
* Jean Tourrilhes <jt@hpl.hp.com> (new version)
* Created at: Wed Oct 21 20:02:35 1998
* Modified at: Fri Dec 17 09:10:43 1999
* Modified by: Dag Brattli <dagb@cs.uit.no>
*
* Copyright (c) 1998-1999 Dag Brattli, All Rights Reserved.
* Copyright (c) 1999 Jean Tourrilhes
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* Neither Dag Brattli nor University of Tromsø admit liability nor
* provide warranty for any of this software. This material is
* provided "AS-IS" and at no charge.
*
********************************************************************/
/*
* Changelog
*
* 0.8 -> 0.9999 - Jean
* o New initialisation procedure : much safer and correct
* o New procedure the change speed : much faster and simpler
* o Other cleanups & comments
* Thanks to Lichen Wang @ Actisys for his excellent help...
*/
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/tty.h>
#include <linux/init.h>
#include <net/irda/irda.h>
#include <net/irda/irda_device.h>
/*
* Define the timing of the pulses we send to the dongle (to reset it, and
* to toggle speeds). Basically, the limit here is the propagation speed of
* the signals through the serial port, the dongle being much faster. Any
* serial port support 115 kb/s, so we are sure that pulses 8.5 us wide can
* go through cleanly . If you are on the wild side, you can try to lower
* this value (Actisys recommended me 2 us, and 0 us work for me on a P233!)
*/
#define MIN_DELAY 10 /* 10 us to be on the conservative side */
static int actisys_change_speed(struct irda_task *task);
static int actisys_reset(struct irda_task *task);
static void actisys_open(dongle_t *self, struct qos_info *qos);
static void actisys_close(dongle_t *self);
/* These are the baudrates supported, in the order available */
/* Note : the 220L doesn't support 38400, but we will fix that below */
static __u32 baud_rates[] = { 9600, 19200, 57600, 115200, 38400 };
#define MAX_SPEEDS 5
static struct dongle_reg dongle = {
.type = IRDA_ACTISYS_DONGLE,
.open = actisys_open,
.close = actisys_close,
.reset = actisys_reset,
.change_speed = actisys_change_speed,
.owner = THIS_MODULE,
};
static struct dongle_reg dongle_plus = {
.type = IRDA_ACTISYS_PLUS_DONGLE,
.open = actisys_open,
.close = actisys_close,
.reset = actisys_reset,
.change_speed = actisys_change_speed,
.owner = THIS_MODULE,
};
/*
* Function actisys_change_speed (task)
*
* There is two model of Actisys dongle we are dealing with,
* the 220L and 220L+. At this point, only irattach knows with
* kind the user has requested (it was an argument on irattach
* command line).
* So, we register a dongle of each sort and let irattach
* pick the right one...
*/
static int __init actisys_init(void)
{
int ret;
/* First, register an Actisys 220L dongle */
ret = irda_device_register_dongle(&dongle);
if (ret < 0)
return ret;
/* Now, register an Actisys 220L+ dongle */
ret = irda_device_register_dongle(&dongle_plus);
if (ret < 0) {
irda_device_unregister_dongle(&dongle);
return ret;
}
return 0;
}
static void __exit actisys_cleanup(void)
{
/* We have to remove both dongles */
irda_device_unregister_dongle(&dongle);
irda_device_unregister_dongle(&dongle_plus);
}
static void actisys_open(dongle_t *self, struct qos_info *qos)
{
/* Power on the dongle */
self->set_dtr_rts(self->dev, TRUE, TRUE);
/* Set the speeds we can accept */
qos->baud_rate.bits &= IR_9600|IR_19200|IR_38400|IR_57600|IR_115200;
/* Remove support for 38400 if this is not a 220L+ dongle */
if (self->issue->type == IRDA_ACTISYS_DONGLE)
qos->baud_rate.bits &= ~IR_38400;
qos->min_turn_time.bits = 0x7f; /* Needs 0.01 ms */
}
static void actisys_close(dongle_t *self)
{
/* Power off the dongle */
self->set_dtr_rts(self->dev, FALSE, FALSE);
}
/*
* Function actisys_change_speed (task)
*
* Change speed of the ACTiSYS IR-220L and IR-220L+ type IrDA dongles.
* To cycle through the available baud rates, pulse RTS low for a few us.
*
* First, we reset the dongle to always start from a known state.
* Then, we cycle through the speeds by pulsing RTS low and then up.
* The dongle allow us to pulse quite fast, se we can set speed in one go,
* which is must faster ( < 100 us) and less complex than what is found
* in some other dongle drivers...
* Note that even if the new speed is the same as the current speed,
* we reassert the speed. This make sure that things are all right,
* and it's fast anyway...
* By the way, this function will work for both type of dongles,
* because the additional speed is at the end of the sequence...
*/
static int actisys_change_speed(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
__u32 speed = (__u32) task->param; /* Target speed */
int ret = 0;
int i = 0;
IRDA_DEBUG(4, "%s(), speed=%d (was %d)\n", __FUNCTION__, speed,
self->speed);
/* Go to a known state by reseting the dongle */
/* Reset the dongle : set DTR low for 10 us */
self->set_dtr_rts(self->dev, FALSE, TRUE);
udelay(MIN_DELAY);
/* Go back to normal mode (we are now at 9600 b/s) */
self->set_dtr_rts(self->dev, TRUE, TRUE);
/*
* Now, we can set the speed requested. Send RTS pulses until we
* reach the target speed
*/
for (i=0; i<MAX_SPEEDS; i++) {
if (speed == baud_rates[i]) {
self->speed = baud_rates[i];
break;
}
/* Make sure previous pulse is finished */
udelay(MIN_DELAY);
/* Set RTS low for 10 us */
self->set_dtr_rts(self->dev, TRUE, FALSE);
udelay(MIN_DELAY);
/* Set RTS high for 10 us */
self->set_dtr_rts(self->dev, TRUE, TRUE);
}
/* Check if life is sweet... */
if (i >= MAX_SPEEDS)
ret = -1; /* This should not happen */
/* Basta lavoro, on se casse d'ici... */
irda_task_next_state(task, IRDA_TASK_DONE);
return ret;
}
/*
* Function actisys_reset (task)
*
* Reset the Actisys type dongle. Warning, this function must only be
* called with a process context!
*
* We need to do two things in this function :
* o first make sure that the dongle is in a state where it can operate
* o second put the dongle in a know state
*
* The dongle is powered of the RTS and DTR lines. In the dongle, there
* is a big capacitor to accommodate the current spikes. This capacitor
* takes a least 50 ms to be charged. In theory, the Bios set those lines
* up, so by the time we arrive here we should be set. It doesn't hurt
* to be on the conservative side, so we will wait...
* Then, we set the speed to 9600 b/s to get in a known state (see in
* change_speed for details). It is needed because the IrDA stack
* has tried to set the speed immediately after our first return,
* so before we can be sure the dongle is up and running.
*/
static int actisys_reset(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
int ret = 0;
IRDA_ASSERT(task != NULL, return -1;);
self->reset_task = task;
switch (task->state) {
case IRDA_TASK_INIT:
/* Set both DTR & RTS to power up the dongle */
/* In theory redundant with power up in actisys_open() */
self->set_dtr_rts(self->dev, TRUE, TRUE);
/* Sleep 50 ms to make sure capacitor is charged */
ret = msecs_to_jiffies(50);
irda_task_next_state(task, IRDA_TASK_WAIT);
break;
case IRDA_TASK_WAIT:
/* Reset the dongle : set DTR low for 10 us */
self->set_dtr_rts(self->dev, FALSE, TRUE);
udelay(MIN_DELAY);
/* Go back to normal mode */
self->set_dtr_rts(self->dev, TRUE, TRUE);
irda_task_next_state(task, IRDA_TASK_DONE);
self->reset_task = NULL;
self->speed = 9600; /* That's the default */
break;
default:
IRDA_ERROR("%s(), unknown state %d\n",
__FUNCTION__, task->state);
irda_task_next_state(task, IRDA_TASK_DONE);
self->reset_task = NULL;
ret = -1;
break;
}
return ret;
}
MODULE_AUTHOR("Dag Brattli <dagb@cs.uit.no> - Jean Tourrilhes <jt@hpl.hp.com>");
MODULE_DESCRIPTION("ACTiSYS IR-220L and IR-220L+ dongle driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("irda-dongle-2"); /* IRDA_ACTISYS_DONGLE */
MODULE_ALIAS("irda-dongle-3"); /* IRDA_ACTISYS_PLUS_DONGLE */
/*
* Function init_module (void)
*
* Initialize Actisys module
*
*/
module_init(actisys_init);
/*
* Function cleanup_module (void)
*
* Cleanup Actisys module
*
*/
module_exit(actisys_cleanup);
drivers/net/irda/ep7211_ir.c 已删除 100644 → 0
浏览文件 @ e9888f54
/*
* IR port driver for the Cirrus Logic EP7211 processor.
*
* Copyright 2001, Blue Mug Inc. All rights reserved.
*/
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/tty.h>
#include <linux/init.h>
#include <linux/spinlock.h>
#include <net/irda/irda.h>
#include <net/irda/irda_device.h>
#include <asm/io.h>
#include <asm/hardware.h>
#define MIN_DELAY 25 /* 15 us, but wait a little more to be sure */
#define MAX_DELAY 10000 /* 1 ms */
static void ep7211_ir_open(dongle_t *self, struct qos_info *qos);
static void ep7211_ir_close(dongle_t *self);
static int ep7211_ir_change_speed(struct irda_task *task);
static int ep7211_ir_reset(struct irda_task *task);
static DEFINE_SPINLOCK(ep7211_lock);
static struct dongle_reg dongle = {
.type = IRDA_EP7211_IR,
.open = ep7211_ir_open,
.close = ep7211_ir_close,
.reset = ep7211_ir_reset,
.change_speed = ep7211_ir_change_speed,
.owner = THIS_MODULE,
};
static void ep7211_ir_open(dongle_t *self, struct qos_info *qos)
{
unsigned int syscon1, flags;
spin_lock_irqsave(&ep7211_lock, flags);
/* Turn on the SIR encoder. */
syscon1 = clps_readl(SYSCON1);
syscon1 |= SYSCON1_SIREN;
clps_writel(syscon1, SYSCON1);
/* XXX: We should disable modem status interrupts on the first
UART (interrupt #14). */
spin_unlock_irqrestore(&ep7211_lock, flags);
}
static void ep7211_ir_close(dongle_t *self)
{
unsigned int syscon1, flags;
spin_lock_irqsave(&ep7211_lock, flags);
/* Turn off the SIR encoder. */
syscon1 = clps_readl(SYSCON1);
syscon1 &= ~SYSCON1_SIREN;
clps_writel(syscon1, SYSCON1);
/* XXX: If we've disabled the modem status interrupts, we should
reset them back to their original state. */
spin_unlock_irqrestore(&ep7211_lock, flags);
}
/*
* Function ep7211_ir_change_speed (task)
*
* Change speed of the EP7211 I/R port. We don't really have to do anything
* for the EP7211 as long as the rate is being changed at the serial port
* level.
*/
static int ep7211_ir_change_speed(struct irda_task *task)
{
irda_task_next_state(task, IRDA_TASK_DONE);
return 0;
}
/*
* Function ep7211_ir_reset (task)
*
* Reset the EP7211 I/R. We don't really have to do anything.
*
*/
static int ep7211_ir_reset(struct irda_task *task)
{
irda_task_next_state(task, IRDA_TASK_DONE);
return 0;
}
/*
* Function ep7211_ir_init(void)
*
* Initialize EP7211 I/R module
*
*/
static int __init ep7211_ir_init(void)
{
return irda_device_register_dongle(&dongle);
}
/*
* Function ep7211_ir_cleanup(void)
*
* Cleanup EP7211 I/R module
*
*/
static void __exit ep7211_ir_cleanup(void)
{
irda_device_unregister_dongle(&dongle);
}
MODULE_AUTHOR("Jon McClintock <jonm@bluemug.com>");
MODULE_DESCRIPTION("EP7211 I/R driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("irda-dongle-8"); /* IRDA_EP7211_IR */
module_init(ep7211_ir_init);
module_exit(ep7211_ir_cleanup);
drivers/net/irda/esi.c 已删除 100644 → 0
浏览文件 @ e9888f54
/*********************************************************************
*
* Filename: esi.c
* Version: 1.5
* Description: Driver for the Extended Systems JetEye PC dongle
* Status: Experimental.
* Author: Dag Brattli <dagb@cs.uit.no>
* Created at: Sat Feb 21 18:54:38 1998
* Modified at: Fri Dec 17 09:14:04 1999
* Modified by: Dag Brattli <dagb@cs.uit.no>
*
* Copyright (c) 1999 Dag Brattli, <dagb@cs.uit.no>,
* Copyright (c) 1998 Thomas Davis, <ratbert@radiks.net>,
* All Rights Reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*
********************************************************************/
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/tty.h>
#include <linux/init.h>
#include <net/irda/irda.h>
#include <net/irda/irda_device.h>
static void esi_open(dongle_t *self, struct qos_info *qos);
static void esi_close(dongle_t *self);
static int esi_change_speed(struct irda_task *task);
static int esi_reset(struct irda_task *task);
static struct dongle_reg dongle = {
.type = IRDA_ESI_DONGLE,
.open = esi_open,
.close = esi_close,
.reset = esi_reset,
.change_speed = esi_change_speed,
.owner = THIS_MODULE,
};
static int __init esi_init(void)
{
return irda_device_register_dongle(&dongle);
}
static void __exit esi_cleanup(void)
{
irda_device_unregister_dongle(&dongle);
}
static void esi_open(dongle_t *self, struct qos_info *qos)
{
qos->baud_rate.bits &= IR_9600|IR_19200|IR_115200;
qos->min_turn_time.bits = 0x01; /* Needs at least 10 ms */
}
static void esi_close(dongle_t *dongle)
{
/* Power off dongle */
dongle->set_dtr_rts(dongle->dev, FALSE, FALSE);
}
/*
* Function esi_change_speed (task)
*
* Set the speed for the Extended Systems JetEye PC ESI-9680 type dongle
*
*/
static int esi_change_speed(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
__u32 speed = (__u32) task->param;
int dtr, rts;
switch (speed) {
case 19200:
dtr = TRUE;
rts = FALSE;
break;
case 115200:
dtr = rts = TRUE;
break;
case 9600:
default:
dtr = FALSE;
rts = TRUE;
break;
}
/* Change speed of dongle */
self->set_dtr_rts(self->dev, dtr, rts);
self->speed = speed;
irda_task_next_state(task, IRDA_TASK_DONE);
return 0;
}
/*
* Function esi_reset (task)
*
* Reset dongle;
*
*/
static int esi_reset(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
self->set_dtr_rts(self->dev, FALSE, FALSE);
irda_task_next_state(task, IRDA_TASK_DONE);
return 0;
}
MODULE_AUTHOR("Dag Brattli <dagb@cs.uit.no>");
MODULE_DESCRIPTION("Extended Systems JetEye PC dongle driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("irda-dongle-1"); /* IRDA_ESI_DONGLE */
/*
* Function init_module (void)
*
* Initialize ESI module
*
*/
module_init(esi_init);
/*
* Function cleanup_module (void)
*
* Cleanup ESI module
*
*/
module_exit(esi_cleanup);
drivers/net/irda/girbil.c 已删除 100644 → 0
浏览文件 @ e9888f54
/*********************************************************************
*
* Filename: girbil.c
* Version: 1.2
* Description: Implementation for the Greenwich GIrBIL dongle
* Status: Experimental.
* Author: Dag Brattli <dagb@cs.uit.no>
* Created at: Sat Feb 6 21:02:33 1999
* Modified at: Fri Dec 17 09:13:20 1999
* Modified by: Dag Brattli <dagb@cs.uit.no>
*
* Copyright (c) 1999 Dag Brattli, All Rights Reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* Neither Dag Brattli nor University of Tromsø admit liability nor
* provide warranty for any of this software. This material is
* provided "AS-IS" and at no charge.
*
********************************************************************/
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/tty.h>
#include <linux/init.h>
#include <net/irda/irda.h>
#include <net/irda/irda_device.h>
static int girbil_reset(struct irda_task *task);
static void girbil_open(dongle_t *self, struct qos_info *qos);
static void girbil_close(dongle_t *self);
static int girbil_change_speed(struct irda_task *task);
/* Control register 1 */
#define GIRBIL_TXEN 0x01 /* Enable transmitter */
#define GIRBIL_RXEN 0x02 /* Enable receiver */
#define GIRBIL_ECAN 0x04 /* Cancel self emmited data */
#define GIRBIL_ECHO 0x08 /* Echo control characters */
/* LED Current Register (0x2) */
#define GIRBIL_HIGH 0x20
#define GIRBIL_MEDIUM 0x21
#define GIRBIL_LOW 0x22
/* Baud register (0x3) */
#define GIRBIL_2400 0x30
#define GIRBIL_4800 0x31
#define GIRBIL_9600 0x32
#define GIRBIL_19200 0x33
#define GIRBIL_38400 0x34
#define GIRBIL_57600 0x35
#define GIRBIL_115200 0x36
/* Mode register (0x4) */
#define GIRBIL_IRDA 0x40
#define GIRBIL_ASK 0x41
/* Control register 2 (0x5) */
#define GIRBIL_LOAD 0x51 /* Load the new baud rate value */
static struct dongle_reg dongle = {
.type = IRDA_GIRBIL_DONGLE,
.open = girbil_open,
.close = girbil_close,
.reset = girbil_reset,
.change_speed = girbil_change_speed,
.owner = THIS_MODULE,
};
static int __init girbil_init(void)
{
return irda_device_register_dongle(&dongle);
}
static void __exit girbil_cleanup(void)
{
irda_device_unregister_dongle(&dongle);
}
static void girbil_open(dongle_t *self, struct qos_info *qos)
{
qos->baud_rate.bits &= IR_9600|IR_19200|IR_38400|IR_57600|IR_115200;
qos->min_turn_time.bits = 0x03;
}
static void girbil_close(dongle_t *self)
{
/* Power off dongle */
self->set_dtr_rts(self->dev, FALSE, FALSE);
}
/*
* Function girbil_change_speed (dev, speed)
*
* Set the speed for the Girbil type dongle.
*
*/
static int girbil_change_speed(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
__u32 speed = (__u32) task->param;
__u8 control[2];
int ret = 0;
self->speed_task = task;
switch (task->state) {
case IRDA_TASK_INIT:
/* Need to reset the dongle and go to 9600 bps before
programming */
if (irda_task_execute(self, girbil_reset, NULL, task,
(void *) speed))
{
/* Dongle need more time to reset */
irda_task_next_state(task, IRDA_TASK_CHILD_WAIT);
/* Give reset 1 sec to finish */
ret = msecs_to_jiffies(1000);
}
break;
case IRDA_TASK_CHILD_WAIT:
IRDA_WARNING("%s(), resetting dongle timed out!\n",
__FUNCTION__);
ret = -1;
break;
case IRDA_TASK_CHILD_DONE:
/* Set DTR and Clear RTS to enter command mode */
self->set_dtr_rts(self->dev, FALSE, TRUE);
switch (speed) {
case 9600:
default:
control[0] = GIRBIL_9600;
break;
case 19200:
control[0] = GIRBIL_19200;
break;
case 34800:
control[0] = GIRBIL_38400;
break;
case 57600:
control[0] = GIRBIL_57600;
break;
case 115200:
control[0] = GIRBIL_115200;
break;
}
control[1] = GIRBIL_LOAD;
/* Write control bytes */
self->write(self->dev, control, 2);
irda_task_next_state(task, IRDA_TASK_WAIT);
ret = msecs_to_jiffies(100);
break;
case IRDA_TASK_WAIT:
/* Go back to normal mode */
self->set_dtr_rts(self->dev, TRUE, TRUE);
irda_task_next_state(task, IRDA_TASK_DONE);
self->speed_task = NULL;
break;
default:
IRDA_ERROR("%s(), unknown state %d\n",
__FUNCTION__, task->state);
irda_task_next_state(task, IRDA_TASK_DONE);
self->speed_task = NULL;
ret = -1;
break;
}
return ret;
}
/*
* Function girbil_reset (driver)
*
* This function resets the girbil dongle.
*
* Algorithm:
* 0. set RTS, and wait at least 5 ms
* 1. clear RTS
*/
static int girbil_reset(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
__u8 control = GIRBIL_TXEN | GIRBIL_RXEN;
int ret = 0;
self->reset_task = task;
switch (task->state) {
case IRDA_TASK_INIT:
/* Reset dongle */
self->set_dtr_rts(self->dev, TRUE, FALSE);
irda_task_next_state(task, IRDA_TASK_WAIT1);
/* Sleep at least 5 ms */
ret = msecs_to_jiffies(20);
break;
case IRDA_TASK_WAIT1:
/* Set DTR and clear RTS to enter command mode */
self->set_dtr_rts(self->dev, FALSE, TRUE);
irda_task_next_state(task, IRDA_TASK_WAIT2);
ret = msecs_to_jiffies(20);
break;
case IRDA_TASK_WAIT2:
/* Write control byte */
self->write(self->dev, &control, 1);
irda_task_next_state(task, IRDA_TASK_WAIT3);
ret = msecs_to_jiffies(20);
break;
case IRDA_TASK_WAIT3:
/* Go back to normal mode */
self->set_dtr_rts(self->dev, TRUE, TRUE);
irda_task_next_state(task, IRDA_TASK_DONE);
self->reset_task = NULL;
break;
default:
IRDA_ERROR("%s(), unknown state %d\n",
__FUNCTION__, task->state);
irda_task_next_state(task, IRDA_TASK_DONE);
self->reset_task = NULL;
ret = -1;
break;
}
return ret;
}
MODULE_AUTHOR("Dag Brattli <dagb@cs.uit.no>");
MODULE_DESCRIPTION("Greenwich GIrBIL dongle driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("irda-dongle-4"); /* IRDA_GIRBIL_DONGLE */
/*
* Function init_module (void)
*
* Initialize Girbil module
*
*/
module_init(girbil_init);
/*
* Function cleanup_module (void)
*
* Cleanup Girbil module
*
*/
module_exit(girbil_cleanup);
drivers/net/irda/litelink.c 已删除 100644 → 0
浏览文件 @ e9888f54
/*********************************************************************
*
* Filename: litelink.c
* Version: 1.1
* Description: Driver for the Parallax LiteLink dongle
* Status: Stable
* Author: Dag Brattli <dagb@cs.uit.no>
* Created at: Fri May 7 12:50:33 1999
* Modified at: Fri Dec 17 09:14:23 1999
* Modified by: Dag Brattli <dagb@cs.uit.no>
*
* Copyright (c) 1999 Dag Brattli, All Rights Reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*
********************************************************************/
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/tty.h>
#include <linux/init.h>
#include <net/irda/irda.h>
#include <net/irda/irda_device.h>
#define MIN_DELAY 25 /* 15 us, but wait a little more to be sure */
#define MAX_DELAY 10000 /* 1 ms */
static void litelink_open(dongle_t *self, struct qos_info *qos);
static void litelink_close(dongle_t *self);
static int litelink_change_speed(struct irda_task *task);
static int litelink_reset(struct irda_task *task);
/* These are the baudrates supported */
static __u32 baud_rates[] = { 115200, 57600, 38400, 19200, 9600 };
static struct dongle_reg dongle = {
.type = IRDA_LITELINK_DONGLE,
.open = litelink_open,
.close = litelink_close,
.reset = litelink_reset,
.change_speed = litelink_change_speed,
.owner = THIS_MODULE,
};
static int __init litelink_init(void)
{
return irda_device_register_dongle(&dongle);
}
static void __exit litelink_cleanup(void)
{
irda_device_unregister_dongle(&dongle);
}
static void litelink_open(dongle_t *self, struct qos_info *qos)
{
qos->baud_rate.bits &= IR_9600|IR_19200|IR_38400|IR_57600|IR_115200;
qos->min_turn_time.bits = 0x7f; /* Needs 0.01 ms */
}
static void litelink_close(dongle_t *self)
{
/* Power off dongle */
self->set_dtr_rts(self->dev, FALSE, FALSE);
}
/*
* Function litelink_change_speed (task)
*
* Change speed of the Litelink dongle. To cycle through the available
* baud rates, pulse RTS low for a few ms.
*/
static int litelink_change_speed(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
__u32 speed = (__u32) task->param;
int i;
/* Clear RTS to reset dongle */
self->set_dtr_rts(self->dev, TRUE, FALSE);
/* Sleep a minimum of 15 us */
udelay(MIN_DELAY);
/* Go back to normal mode */
self->set_dtr_rts(self->dev, TRUE, TRUE);
/* Sleep a minimum of 15 us */
udelay(MIN_DELAY);
/* Cycle through avaiable baudrates until we reach the correct one */
for (i=0; i<5 && baud_rates[i] != speed; i++) {
/* Set DTR, clear RTS */
self->set_dtr_rts(self->dev, FALSE, TRUE);
/* Sleep a minimum of 15 us */
udelay(MIN_DELAY);
/* Set DTR, Set RTS */
self->set_dtr_rts(self->dev, TRUE, TRUE);
/* Sleep a minimum of 15 us */
udelay(MIN_DELAY);
}
irda_task_next_state(task, IRDA_TASK_DONE);
return 0;
}
/*
* Function litelink_reset (task)
*
* Reset the Litelink type dongle.
*
*/
static int litelink_reset(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
/* Power on dongle */
self->set_dtr_rts(self->dev, TRUE, TRUE);
/* Sleep a minimum of 15 us */
udelay(MIN_DELAY);
/* Clear RTS to reset dongle */
self->set_dtr_rts(self->dev, TRUE, FALSE);
/* Sleep a minimum of 15 us */
udelay(MIN_DELAY);
/* Go back to normal mode */
self->set_dtr_rts(self->dev, TRUE, TRUE);
/* Sleep a minimum of 15 us */
udelay(MIN_DELAY);
/* This dongles speed defaults to 115200 bps */
self->speed = 115200;
irda_task_next_state(task, IRDA_TASK_DONE);
return 0;
}
MODULE_AUTHOR("Dag Brattli <dagb@cs.uit.no>");
MODULE_DESCRIPTION("Parallax Litelink dongle driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("irda-dongle-5"); /* IRDA_LITELINK_DONGLE */
/*
* Function init_module (void)
*
* Initialize Litelink module
*
*/
module_init(litelink_init);
/*
* Function cleanup_module (void)
*
* Cleanup Litelink module
*
*/
module_exit(litelink_cleanup);
drivers/net/irda/ma600.c 已删除 100644 → 0
浏览文件 @ e9888f54
/*********************************************************************
*
* Filename: ma600.c
* Version: 0.1
* Description: Implementation of the MA600 dongle
* Status: Experimental.
* Author: Leung <95Etwl@alumni.ee.ust.hk> http://www.engsvr.ust/~eetwl95
* Created at: Sat Jun 10 20:02:35 2000
* Modified at:
* Modified by:
*
* Note: very thanks to Mr. Maru Wang <maru@mobileaction.com.tw> for providing
* information on the MA600 dongle
*
* Copyright (c) 2000 Leung, All Rights Reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*
********************************************************************/
/* define this macro for release version */
//#define NDEBUG
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/tty.h>
#include <linux/init.h>
#include <net/irda/irda.h>
#include <net/irda/irda_device.h>
#ifndef NDEBUG
#undef IRDA_DEBUG
#define IRDA_DEBUG(n, args...) (printk(KERN_DEBUG args))
#undef ASSERT
#define ASSERT(expr, func) \
if(!(expr)) { \
printk( "Assertion failed! %s,%s,%s,line=%d\n",\
#expr,__FILE__,__FUNCTION__,__LINE__); \
func}
#endif
/* convert hex value to ascii hex */
static const char hexTbl[] = "0123456789ABCDEF";
static void ma600_open(dongle_t *self, struct qos_info *qos);
static void ma600_close(dongle_t *self);
static int ma600_change_speed(struct irda_task *task);
static int ma600_reset(struct irda_task *task);
/* control byte for MA600 */
#define MA600_9600 0x00
#define MA600_19200 0x01
#define MA600_38400 0x02
#define MA600_57600 0x03
#define MA600_115200 0x04
#define MA600_DEV_ID1 0x05
#define MA600_DEV_ID2 0x06
#define MA600_2400 0x08
static struct dongle_reg dongle = {
.type = IRDA_MA600_DONGLE,
.open = ma600_open,
.close = ma600_close,
.reset = ma600_reset,
.change_speed = ma600_change_speed,
.owner = THIS_MODULE,
};
static int __init ma600_init(void)
{
IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
return irda_device_register_dongle(&dongle);
}
static void __exit ma600_cleanup(void)
{
IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
irda_device_unregister_dongle(&dongle);
}
/*
Power on:
(0) Clear RTS and DTR for 1 second
(1) Set RTS and DTR for 1 second
(2) 9600 bps now
Note: assume RTS, DTR are clear before
*/
static void ma600_open(dongle_t *self, struct qos_info *qos)
{
IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
qos->baud_rate.bits &= IR_2400|IR_9600|IR_19200|IR_38400
|IR_57600|IR_115200;
qos->min_turn_time.bits = 0x01; /* Needs at least 1 ms */
irda_qos_bits_to_value(qos);
//self->set_dtr_rts(self->dev, FALSE, FALSE);
// should wait 1 second
self->set_dtr_rts(self->dev, TRUE, TRUE);
// should wait 1 second
}
static void ma600_close(dongle_t *self)
{
IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
/* Power off dongle */
self->set_dtr_rts(self->dev, FALSE, FALSE);
}
static __u8 get_control_byte(__u32 speed)
{
__u8 byte;
switch (speed) {
default:
case 115200:
byte = MA600_115200;
break;
case 57600:
byte = MA600_57600;
break;
case 38400:
byte = MA600_38400;
break;
case 19200:
byte = MA600_19200;
break;
case 9600:
byte = MA600_9600;
break;
case 2400:
byte = MA600_2400;
break;
}
return byte;
}
/*
* Function ma600_change_speed (dev, state, speed)
*
* Set the speed for the MA600 type dongle. Warning, this
* function must be called with a process context!
*
* Algorithm
* 1. Reset
* 2. clear RTS, set DTR and wait for 1ms
* 3. send Control Byte to the MA600 through TXD to set new baud rate
* wait until the stop bit of Control Byte is sent (for 9600 baud rate,
* it takes about 10 msec)
* 4. set RTS, set DTR (return to NORMAL Operation)
* 5. wait at least 10 ms, new setting (baud rate, etc) takes effect here
* after
*/
static int ma600_change_speed(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
__u32 speed = (__u32) task->param;
static __u8 byte;
__u8 byte_echo;
int ret = 0;
IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
ASSERT(task != NULL, return -1;);
if (self->speed_task && self->speed_task != task) {
IRDA_DEBUG(0, "%s(), busy!\n", __FUNCTION__);
return msecs_to_jiffies(10);
} else {
self->speed_task = task;
}
switch (task->state) {
case IRDA_TASK_INIT:
case IRDA_TASK_CHILD_INIT:
/*
* Need to reset the dongle and go to 9600 bps before
* programming
*/
if (irda_task_execute(self, ma600_reset, NULL, task,
(void *) speed)) {
/* Dongle need more time to reset */
irda_task_next_state(task, IRDA_TASK_CHILD_WAIT);
/* give 1 second to finish */
ret = msecs_to_jiffies(1000);
} else {
irda_task_next_state(task, IRDA_TASK_CHILD_DONE);
}
break;
case IRDA_TASK_CHILD_WAIT:
IRDA_WARNING("%s(), resetting dongle timed out!\n",
__FUNCTION__);
ret = -1;
break;
case IRDA_TASK_CHILD_DONE:
/* Set DTR, Clear RTS */
self->set_dtr_rts(self->dev, TRUE, FALSE);
ret = msecs_to_jiffies(1); /* Sleep 1 ms */
irda_task_next_state(task, IRDA_TASK_WAIT);
break;
case IRDA_TASK_WAIT:
speed = (__u32) task->param;
byte = get_control_byte(speed);
/* Write control byte */
self->write(self->dev, &byte, sizeof(byte));
irda_task_next_state(task, IRDA_TASK_WAIT1);
/* Wait at least 10 ms */
ret = msecs_to_jiffies(15);
break;
case IRDA_TASK_WAIT1:
/* Read control byte echo */
self->read(self->dev, &byte_echo, sizeof(byte_echo));
if(byte != byte_echo) {
/* if control byte != echo, I don't know what to do */
printk(KERN_WARNING "%s() control byte written != read!\n", __FUNCTION__);
printk(KERN_WARNING "control byte = 0x%c%c\n",
hexTbl[(byte>>4)&0x0f], hexTbl[byte&0x0f]);
printk(KERN_WARNING "byte echo = 0x%c%c\n",
hexTbl[(byte_echo>>4) & 0x0f],
hexTbl[byte_echo & 0x0f]);
#ifndef NDEBUG
} else {
IRDA_DEBUG(2, "%s() control byte write read OK\n", __FUNCTION__);
#endif
}
/* Set DTR, Set RTS */
self->set_dtr_rts(self->dev, TRUE, TRUE);
irda_task_next_state(task, IRDA_TASK_WAIT2);
/* Wait at least 10 ms */
ret = msecs_to_jiffies(10);
break;
case IRDA_TASK_WAIT2:
irda_task_next_state(task, IRDA_TASK_DONE);
self->speed_task = NULL;
break;
default:
IRDA_ERROR("%s(), unknown state %d\n",
__FUNCTION__, task->state);
irda_task_next_state(task, IRDA_TASK_DONE);
self->speed_task = NULL;
ret = -1;
break;
}
return ret;
}
/*
* Function ma600_reset (driver)
*
* This function resets the ma600 dongle. Warning, this function
* must be called with a process context!!
*
* Algorithm:
* 0. DTR=0, RTS=1 and wait 10 ms
* 1. DTR=1, RTS=1 and wait 10 ms
* 2. 9600 bps now
*/
int ma600_reset(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
int ret = 0;
IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
ASSERT(task != NULL, return -1;);
if (self->reset_task && self->reset_task != task) {
IRDA_DEBUG(0, "%s(), busy!\n", __FUNCTION__);
return msecs_to_jiffies(10);
} else
self->reset_task = task;
switch (task->state) {
case IRDA_TASK_INIT:
/* Clear DTR and Set RTS */
self->set_dtr_rts(self->dev, FALSE, TRUE);
irda_task_next_state(task, IRDA_TASK_WAIT1);
ret = msecs_to_jiffies(10); /* Sleep 10 ms */
break;
case IRDA_TASK_WAIT1:
/* Set DTR and RTS */
self->set_dtr_rts(self->dev, TRUE, TRUE);
irda_task_next_state(task, IRDA_TASK_WAIT2);
ret = msecs_to_jiffies(10); /* Sleep 10 ms */
break;
case IRDA_TASK_WAIT2:
irda_task_next_state(task, IRDA_TASK_DONE);
self->reset_task = NULL;
break;
default:
IRDA_ERROR("%s(), unknown state %d\n",
__FUNCTION__, task->state);
irda_task_next_state(task, IRDA_TASK_DONE);
self->reset_task = NULL;
ret = -1;
}
return ret;
}
MODULE_AUTHOR("Leung <95Etwl@alumni.ee.ust.hk> http://www.engsvr.ust/~eetwl95");
MODULE_DESCRIPTION("MA600 dongle driver version 0.1");
MODULE_LICENSE("GPL");
MODULE_ALIAS("irda-dongle-11"); /* IRDA_MA600_DONGLE */
/*
* Function init_module (void)
*
* Initialize MA600 module
*
*/
module_init(ma600_init);
/*
* Function cleanup_module (void)
*
* Cleanup MA600 module
*
*/
module_exit(ma600_cleanup);
drivers/net/irda/mcp2120.c 已删除 100644 → 0
浏览文件 @ e9888f54
/*********************************************************************
*
*
* Filename: mcp2120.c
* Version: 1.0
* Description: Implementation for the MCP2120 (Microchip)
* Status: Experimental.
* Author: Felix Tang (tangf@eyetap.org)
* Created at: Sun Mar 31 19:32:12 EST 2002
* Based on code by: Dag Brattli <dagb@cs.uit.no>
*
* Copyright (c) 2002 Felix Tang, All Rights Reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
********************************************************************/
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/tty.h>
#include <linux/init.h>
#include <net/irda/irda.h>
#include <net/irda/irda_device.h>
static int mcp2120_reset(struct irda_task *task);
static void mcp2120_open(dongle_t *self, struct qos_info *qos);
static void mcp2120_close(dongle_t *self);
static int mcp2120_change_speed(struct irda_task *task);
#define MCP2120_9600 0x87
#define MCP2120_19200 0x8B
#define MCP2120_38400 0x85
#define MCP2120_57600 0x83
#define MCP2120_115200 0x81
#define MCP2120_COMMIT 0x11
static struct dongle_reg dongle = {
.type = IRDA_MCP2120_DONGLE,
.open = mcp2120_open,
.close = mcp2120_close,
.reset = mcp2120_reset,
.change_speed = mcp2120_change_speed,
.owner = THIS_MODULE,
};
static int __init mcp2120_init(void)
{
return irda_device_register_dongle(&dongle);
}
static void __exit mcp2120_cleanup(void)
{
irda_device_unregister_dongle(&dongle);
}
static void mcp2120_open(dongle_t *self, struct qos_info *qos)
{
qos->baud_rate.bits &= IR_9600|IR_19200|IR_38400|IR_57600|IR_115200;
qos->min_turn_time.bits = 0x01;
}
static void mcp2120_close(dongle_t *self)
{
/* Power off dongle */
/* reset and inhibit mcp2120 */
self->set_dtr_rts(self->dev, TRUE, TRUE);
//self->set_dtr_rts(self->dev, FALSE, FALSE);
}
/*
* Function mcp2120_change_speed (dev, speed)
*
* Set the speed for the MCP2120.
*
*/
static int mcp2120_change_speed(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
__u32 speed = (__u32) task->param;
__u8 control[2];
int ret = 0;
self->speed_task = task;
switch (task->state) {
case IRDA_TASK_INIT:
/* Need to reset the dongle and go to 9600 bps before
programming */
//printk("Dmcp2120_change_speed irda_task_init\n");
if (irda_task_execute(self, mcp2120_reset, NULL, task,
(void *) speed))
{
/* Dongle need more time to reset */
irda_task_next_state(task, IRDA_TASK_CHILD_WAIT);
/* Give reset 1 sec to finish */
ret = msecs_to_jiffies(1000);
}
break;
case IRDA_TASK_CHILD_WAIT:
IRDA_WARNING("%s(), resetting dongle timed out!\n",
__FUNCTION__);
ret = -1;
break;
case IRDA_TASK_CHILD_DONE:
/* Set DTR to enter command mode */
self->set_dtr_rts(self->dev, TRUE, FALSE);
udelay(500);
switch (speed) {
case 9600:
default:
control[0] = MCP2120_9600;
//printk("mcp2120 9600\n");
break;
case 19200:
control[0] = MCP2120_19200;
//printk("mcp2120 19200\n");
break;
case 34800:
control[0] = MCP2120_38400;
//printk("mcp2120 38400\n");
break;
case 57600:
control[0] = MCP2120_57600;
//printk("mcp2120 57600\n");
break;
case 115200:
control[0] = MCP2120_115200;
//printk("mcp2120 115200\n");
break;
}
control[1] = MCP2120_COMMIT;
/* Write control bytes */
self->write(self->dev, control, 2);
irda_task_next_state(task, IRDA_TASK_WAIT);
ret = msecs_to_jiffies(100);
//printk("mcp2120_change_speed irda_child_done\n");
break;
case IRDA_TASK_WAIT:
/* Go back to normal mode */
self->set_dtr_rts(self->dev, FALSE, FALSE);
irda_task_next_state(task, IRDA_TASK_DONE);
self->speed_task = NULL;
//printk("mcp2120_change_speed irda_task_wait\n");
break;
default:
IRDA_ERROR("%s(), unknown state %d\n",
__FUNCTION__, task->state);
irda_task_next_state(task, IRDA_TASK_DONE);
self->speed_task = NULL;
ret = -1;
break;
}
return ret;
}
/*
* Function mcp2120_reset (driver)
*
* This function resets the mcp2120 dongle.
*
* Info: -set RTS to reset mcp2120
* -set DTR to set mcp2120 software command mode
* -mcp2120 defaults to 9600 baud after reset
*
* Algorithm:
* 0. Set RTS to reset mcp2120.
* 1. Clear RTS and wait for device reset timer of 30 ms (max).
*
*/
static int mcp2120_reset(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
int ret = 0;
self->reset_task = task;
switch (task->state) {
case IRDA_TASK_INIT:
//printk("mcp2120_reset irda_task_init\n");
/* Reset dongle by setting RTS*/
self->set_dtr_rts(self->dev, TRUE, TRUE);
irda_task_next_state(task, IRDA_TASK_WAIT1);
ret = msecs_to_jiffies(50);
break;
case IRDA_TASK_WAIT1:
//printk("mcp2120_reset irda_task_wait1\n");
/* clear RTS and wait for at least 30 ms. */
self->set_dtr_rts(self->dev, FALSE, FALSE);
irda_task_next_state(task, IRDA_TASK_WAIT2);
ret = msecs_to_jiffies(50);
break;
case IRDA_TASK_WAIT2:
//printk("mcp2120_reset irda_task_wait2\n");
/* Go back to normal mode */
self->set_dtr_rts(self->dev, FALSE, FALSE);
irda_task_next_state(task, IRDA_TASK_DONE);
self->reset_task = NULL;
break;
default:
IRDA_ERROR("%s(), unknown state %d\n",
__FUNCTION__, task->state);
irda_task_next_state(task, IRDA_TASK_DONE);
self->reset_task = NULL;
ret = -1;
break;
}
return ret;
}
MODULE_AUTHOR("Felix Tang <tangf@eyetap.org>");
MODULE_DESCRIPTION("Microchip MCP2120");
MODULE_LICENSE("GPL");
MODULE_ALIAS("irda-dongle-9"); /* IRDA_MCP2120_DONGLE */
/*
* Function init_module (void)
*
* Initialize MCP2120 module
*
*/
module_init(mcp2120_init);
/*
* Function cleanup_module (void)
*
* Cleanup MCP2120 module
*
*/
module_exit(mcp2120_cleanup);
drivers/net/irda/old_belkin.c 已删除 100644 → 0
浏览文件 @ e9888f54
/*********************************************************************
*
* Filename: old_belkin.c
* Version: 1.1
* Description: Driver for the Belkin (old) SmartBeam dongle
* Status: Experimental...
* Author: Jean Tourrilhes <jt@hpl.hp.com>
* Created at: 22/11/99
* Modified at: Fri Dec 17 09:13:32 1999
* Modified by: Dag Brattli <dagb@cs.uit.no>
*
* Copyright (c) 1999 Jean Tourrilhes, All Rights Reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*
********************************************************************/
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/tty.h>
#include <linux/init.h>
#include <net/irda/irda.h>
#include <net/irda/irda_device.h>
/*
* Belkin is selling a dongle called the SmartBeam.
* In fact, there is two hardware version of this dongle, of course with
* the same name and looking the exactly same (grrr...).
* I guess that I've got the old one, because inside I don't have
* a jumper for IrDA/ASK...
*
* As far as I can make it from info on their web site, the old dongle
* support only 9600 b/s, which make our life much simpler as far as
* the driver is concerned, but you might not like it very much ;-)
* The new SmartBeam does 115 kb/s, and I've not tested it...
*
* Belkin claim that the correct driver for the old dongle (in Windows)
* is the generic Parallax 9500a driver, but the Linux LiteLink driver
* fails for me (probably because Linux-IrDA doesn't rate fallback),
* so I created this really dumb driver...
*
* In fact, this driver doesn't do much. The only thing it does is to
* prevent Linux-IrDA to use any other speed than 9600 b/s ;-) This
* driver is called "old_belkin" so that when the new SmartBeam is supported
* its driver can be called "belkin" instead of "new_belkin".
*
* Note : this driver was written without any info/help from Belkin,
* so a lot of info here might be totally wrong. Blame me ;-)
*/
/* Let's guess */
#define MIN_DELAY 25 /* 15 us, but wait a little more to be sure */
static void old_belkin_open(dongle_t *self, struct qos_info *qos);
static void old_belkin_close(dongle_t *self);
static int old_belkin_change_speed(struct irda_task *task);
static int old_belkin_reset(struct irda_task *task);
/* These are the baudrates supported */
/* static __u32 baud_rates[] = { 9600 }; */
static struct dongle_reg dongle = {
.type = IRDA_OLD_BELKIN_DONGLE,
.open = old_belkin_open,
.close = old_belkin_close,
.reset = old_belkin_reset,
.change_speed = old_belkin_change_speed,
.owner = THIS_MODULE,
};
static int __init old_belkin_init(void)
{
return irda_device_register_dongle(&dongle);
}
static void __exit old_belkin_cleanup(void)
{
irda_device_unregister_dongle(&dongle);
}
static void old_belkin_open(dongle_t *self, struct qos_info *qos)
{
/* Not too fast, please... */
qos->baud_rate.bits &= IR_9600;
/* Needs at least 10 ms (totally wild guess, can do probably better) */
qos->min_turn_time.bits = 0x01;
}
static void old_belkin_close(dongle_t *self)
{
/* Power off dongle */
self->set_dtr_rts(self->dev, FALSE, FALSE);
}
/*
* Function old_belkin_change_speed (task)
*
* With only one speed available, not much to do...
*/
static int old_belkin_change_speed(struct irda_task *task)
{
irda_task_next_state(task, IRDA_TASK_DONE);
return 0;
}
/*
* Function old_belkin_reset (task)
*
* Reset the Old-Belkin type dongle.
*
*/
static int old_belkin_reset(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
/* Power on dongle */
self->set_dtr_rts(self->dev, TRUE, TRUE);
/* Sleep a minimum of 15 us */
udelay(MIN_DELAY);
/* This dongles speed "defaults" to 9600 bps ;-) */
self->speed = 9600;
irda_task_next_state(task, IRDA_TASK_DONE);
return 0;
}
MODULE_AUTHOR("Jean Tourrilhes <jt@hpl.hp.com>");
MODULE_DESCRIPTION("Belkin (old) SmartBeam dongle driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("irda-dongle-7"); /* IRDA_OLD_BELKIN_DONGLE */
/*
* Function init_module (void)
*
* Initialize Old-Belkin module
*
*/
module_init(old_belkin_init);
/*
* Function cleanup_module (void)
*
* Cleanup Old-Belkin module
*
*/
module_exit(old_belkin_cleanup);
drivers/net/irda/tekram.c 已删除 100644 → 0
浏览文件 @ e9888f54
/*********************************************************************
*
* Filename: tekram.c
* Version: 1.2
* Description: Implementation of the Tekram IrMate IR-210B dongle
* Status: Experimental.
* Author: Dag Brattli <dagb@cs.uit.no>
* Created at: Wed Oct 21 20:02:35 1998
* Modified at: Fri Dec 17 09:13:09 1999
* Modified by: Dag Brattli <dagb@cs.uit.no>
*
* Copyright (c) 1998-1999 Dag Brattli, All Rights Reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* Neither Dag Brattli nor University of Tromsø admit liability nor
* provide warranty for any of this software. This material is
* provided "AS-IS" and at no charge.
*
********************************************************************/
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/tty.h>
#include <linux/init.h>
#include <net/irda/irda.h>
#include <net/irda/irda_device.h>
static void tekram_open(dongle_t *self, struct qos_info *qos);
static void tekram_close(dongle_t *self);
static int tekram_change_speed(struct irda_task *task);
static int tekram_reset(struct irda_task *task);
#define TEKRAM_115200 0x00
#define TEKRAM_57600 0x01
#define TEKRAM_38400 0x02
#define TEKRAM_19200 0x03
#define TEKRAM_9600 0x04
#define TEKRAM_PW 0x10 /* Pulse select bit */
static struct dongle_reg dongle = {
.type = IRDA_TEKRAM_DONGLE,
.open = tekram_open,
.close = tekram_close,
.reset = tekram_reset,
.change_speed = tekram_change_speed,
.owner = THIS_MODULE,
};
static int __init tekram_init(void)
{
return irda_device_register_dongle(&dongle);
}
static void __exit tekram_cleanup(void)
{
irda_device_unregister_dongle(&dongle);
}
static void tekram_open(dongle_t *self, struct qos_info *qos)
{
IRDA_DEBUG(2, "%s()\n", __FUNCTION__ );
qos->baud_rate.bits &= IR_9600|IR_19200|IR_38400|IR_57600|IR_115200;
qos->min_turn_time.bits = 0x01; /* Needs at least 10 ms */
irda_qos_bits_to_value(qos);
}
static void tekram_close(dongle_t *self)
{
IRDA_DEBUG(2, "%s()\n", __FUNCTION__ );
/* Power off dongle */
self->set_dtr_rts(self->dev, FALSE, FALSE);
if (self->reset_task)
irda_task_delete(self->reset_task);
if (self->speed_task)
irda_task_delete(self->speed_task);
}
/*
* Function tekram_change_speed (dev, state, speed)
*
* Set the speed for the Tekram IRMate 210 type dongle. Warning, this
* function must be called with a process context!
*
* Algorithm
* 1. clear DTR
* 2. set RTS, and wait at least 7 us
* 3. send Control Byte to the IR-210 through TXD to set new baud rate
* wait until the stop bit of Control Byte is sent (for 9600 baud rate,
* it takes about 100 msec)
* 5. clear RTS (return to NORMAL Operation)
* 6. wait at least 50 us, new setting (baud rate, etc) takes effect here
* after
*/
static int tekram_change_speed(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
__u32 speed = (__u32) task->param;
__u8 byte;
int ret = 0;
IRDA_DEBUG(2, "%s()\n", __FUNCTION__ );
IRDA_ASSERT(task != NULL, return -1;);
if (self->speed_task && self->speed_task != task) {
IRDA_DEBUG(0, "%s(), busy!\n", __FUNCTION__ );
return msecs_to_jiffies(10);
} else
self->speed_task = task;
switch (speed) {
default:
case 9600:
byte = TEKRAM_PW|TEKRAM_9600;
break;
case 19200:
byte = TEKRAM_PW|TEKRAM_19200;
break;
case 38400:
byte = TEKRAM_PW|TEKRAM_38400;
break;
case 57600:
byte = TEKRAM_PW|TEKRAM_57600;
break;
case 115200:
byte = TEKRAM_115200;
break;
}
switch (task->state) {
case IRDA_TASK_INIT:
case IRDA_TASK_CHILD_INIT:
/*
* Need to reset the dongle and go to 9600 bps before
* programming
*/
if (irda_task_execute(self, tekram_reset, NULL, task,
(void *) speed))
{
/* Dongle need more time to reset */
irda_task_next_state(task, IRDA_TASK_CHILD_WAIT);
/* Give reset 1 sec to finish */
ret = msecs_to_jiffies(1000);
} else
irda_task_next_state(task, IRDA_TASK_CHILD_DONE);
break;
case IRDA_TASK_CHILD_WAIT:
IRDA_WARNING("%s(), resetting dongle timed out!\n",
__FUNCTION__);
ret = -1;
break;
case IRDA_TASK_CHILD_DONE:
/* Set DTR, Clear RTS */
self->set_dtr_rts(self->dev, TRUE, FALSE);
/* Wait at least 7us */
udelay(14);
/* Write control byte */
self->write(self->dev, &byte, 1);
irda_task_next_state(task, IRDA_TASK_WAIT);
/* Wait at least 100 ms */
ret = msecs_to_jiffies(150);
break;
case IRDA_TASK_WAIT:
/* Set DTR, Set RTS */
self->set_dtr_rts(self->dev, TRUE, TRUE);
irda_task_next_state(task, IRDA_TASK_DONE);
self->speed_task = NULL;
break;
default:
IRDA_ERROR("%s(), unknown state %d\n",
__FUNCTION__, task->state);
irda_task_next_state(task, IRDA_TASK_DONE);
self->speed_task = NULL;
ret = -1;
break;
}
return ret;
}
/*
* Function tekram_reset (driver)
*
* This function resets the tekram dongle. Warning, this function
* must be called with a process context!!
*
* Algorithm:
* 0. Clear RTS and DTR, and wait 50 ms (power off the IR-210 )
* 1. clear RTS
* 2. set DTR, and wait at least 1 ms
* 3. clear DTR to SPACE state, wait at least 50 us for further
* operation
*/
int tekram_reset(struct irda_task *task)
{
dongle_t *self = (dongle_t *) task->instance;
int ret = 0;
IRDA_DEBUG(2, "%s()\n", __FUNCTION__ );
IRDA_ASSERT(task != NULL, return -1;);
if (self->reset_task && self->reset_task != task) {
IRDA_DEBUG(0, "%s(), busy!\n", __FUNCTION__ );
return msecs_to_jiffies(10);
} else
self->reset_task = task;
/* Power off dongle */
//self->set_dtr_rts(self->dev, FALSE, FALSE);
self->set_dtr_rts(self->dev, TRUE, TRUE);
switch (task->state) {
case IRDA_TASK_INIT:
irda_task_next_state(task, IRDA_TASK_WAIT1);
/* Sleep 50 ms */
ret = msecs_to_jiffies(50);
break;
case IRDA_TASK_WAIT1:
/* Clear DTR, Set RTS */
self->set_dtr_rts(self->dev, FALSE, TRUE);
irda_task_next_state(task, IRDA_TASK_WAIT2);
/* Should sleep 1 ms */
ret = msecs_to_jiffies(1);
break;
case IRDA_TASK_WAIT2:
/* Set DTR, Set RTS */
self->set_dtr_rts(self->dev, TRUE, TRUE);
/* Wait at least 50 us */
udelay(75);
irda_task_next_state(task, IRDA_TASK_DONE);
self->reset_task = NULL;
break;
default:
IRDA_ERROR("%s(), unknown state %d\n",
__FUNCTION__, task->state);
irda_task_next_state(task, IRDA_TASK_DONE);
self->reset_task = NULL;
ret = -1;
}
return ret;
}
MODULE_AUTHOR("Dag Brattli <dagb@cs.uit.no>");
MODULE_DESCRIPTION("Tekram IrMate IR-210B dongle driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("irda-dongle-0"); /* IRDA_TEKRAM_DONGLE */
/*
* Function init_module (void)
*
* Initialize Tekram module
*
*/
module_init(tekram_init);
/*
* Function cleanup_module (void)
*
* Cleanup Tekram module
*
*/
module_exit(tekram_cleanup);
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或