Merge branches 'ib-mfd-arm-iio-pwm-4.11', 'ib-mfd-input-4.11-1',...

Merge branches 'ib-mfd-arm-iio-pwm-4.11', 'ib-mfd-input-4.11-1', 'ib-mfd-mtd-4.11' and 'ib-mfd-power-supply-4.11' into ibs-for-mfd-merged

Documentation/mtd/intel-spi.txt

+Upgrading BIOS using intel-spi
+------------------------------
+
+Many Intel CPUs like Baytrail and Braswell include SPI serial flash host
+controller which is used to hold BIOS and other platform specific data.
+Since contents of the SPI serial flash is crucial for machine to function,
+it is typically protected by different hardware protection mechanisms to
+avoid accidental (or on purpose) overwrite of the content.
+
+Not all manufacturers protect the SPI serial flash, mainly because it
+allows upgrading the BIOS image directly from an OS.
+
+The intel-spi driver makes it possible to read and write the SPI serial
+flash, if certain protection bits are not set and locked. If it finds
+any of them set, the whole MTD device is made read-only to prevent
+partial overwrites. By default the driver exposes SPI serial flash
+contents as read-only but it can be changed from kernel command line,
+passing "intel-spi.writeable=1".
+
+Please keep in mind that overwriting the BIOS image on SPI serial flash
+might render the machine unbootable and requires special equipment like
+Dediprog to revive. You have been warned!
+
+Below are the steps how to upgrade MinnowBoard MAX BIOS directly from
+Linux.
+
+ 1) Download and extract the latest Minnowboard MAX BIOS SPI image
+    [1]. At the time writing this the latest image is v92.
+
+ 2) Install mtd-utils package [2]. We need this in order to erase the SPI
+    serial flash. Distros like Debian and Fedora have this prepackaged with
+    name "mtd-utils".
+
+ 3) Add "intel-spi.writeable=1" to the kernel command line and reboot
+    the board (you can also reload the driver passing "writeable=1" as
+    module parameter to modprobe).
+
+ 4) Once the board is up and running again, find the right MTD partition
+    (it is named as "BIOS"):
+
+    # cat /proc/mtd
+    dev:    size   erasesize  name
+    mtd0: 00800000 00001000 "BIOS"
+
+    So here it will be /dev/mtd0 but it may vary.
+
+ 5) Make backup of the existing image first:
+
+    # dd if=/dev/mtd0ro of=bios.bak
+    16384+0 records in
+    16384+0 records out
+    8388608 bytes (8.4 MB) copied, 10.0269 s, 837 kB/s
+
+ 6) Verify the backup
+
+    # sha1sum /dev/mtd0ro bios.bak
+    fdbb011920572ca6c991377c4b418a0502668b73  /dev/mtd0ro
+    fdbb011920572ca6c991377c4b418a0502668b73  bios.bak
+
+    The SHA1 sums must match. Otherwise do not continue any further!
+
+ 7) Erase the SPI serial flash. After this step, do not reboot the
+    board! Otherwise it will not start anymore.
+
+    # flash_erase /dev/mtd0 0 0
+    Erasing 4 Kibyte @ 7ff000 -- 100 % complete
+
+ 8) Once completed without errors you can write the new BIOS image:
+
+    # dd if=MNW2MAX1.X64.0092.R01.1605221712.bin of=/dev/mtd0
+
+ 9) Verify that the new content of the SPI serial flash matches the new
+    BIOS image:
+
+    # sha1sum /dev/mtd0ro MNW2MAX1.X64.0092.R01.1605221712.bin
+    9b4df9e4be2057fceec3a5529ec3d950836c87a2  /dev/mtd0ro
+    9b4df9e4be2057fceec3a5529ec3d950836c87a2 MNW2MAX1.X64.0092.R01.1605221712.bin
+
+    The SHA1 sums should match.
+
+ 10) Now you can reboot your board and observe the new BIOS starting up
+     properly.
+
+References
+----------
+
+[1] https://firmware.intel.com/sites/default/files/MinnowBoard.MAX_.X64.92.R01.zip
+[2] http://www.linux-mtd.infradead.org/

drivers/input/keyboard/cros_ec_keyb.c

@@ -34,6 +34,8 @@
 #include <linux/mfd/cros_ec.h>
 #include <linux/mfd/cros_ec_commands.h>
 
+#include <asm/unaligned.h>
+
 /*
  * @rows: Number of rows in the keypad
  * @cols: Number of columns in the keypad
@@ -43,8 +45,9 @@
  * @valid_keys: bitmap of existing keys for each matrix column
  * @old_kb_state: bitmap of keys pressed last scan
  * @dev: Device pointer
- * @idev: Input device
  * @ec: Top level ChromeOS device to use to talk to EC
+ * @idev: The input device for the matrix keys.
+ * @bs_idev: The input device for non-matrix buttons and switches (or NULL).
  * @notifier: interrupt event notifier for transport devices
  */
 struct cros_ec_keyb {
@@ -57,12 +60,64 @@ struct cros_ec_keyb {
 	uint8_t *old_kb_state;
 
 	struct device *dev;
-	struct input_dev *idev;
 	struct cros_ec_device *ec;
+
+	struct input_dev *idev;
+	struct input_dev *bs_idev;
 	struct notifier_block notifier;
 };
 
 
+/**
+ * cros_ec_bs_map - Struct mapping Linux keycodes to EC button/switch bitmap
+ * #defines
+ *
+ * @ev_type: The type of the input event to generate (e.g., EV_KEY).
+ * @code: A linux keycode
+ * @bit: A #define like EC_MKBP_POWER_BUTTON or EC_MKBP_LID_OPEN
+ * @inverted: If the #define and EV_SW have opposite meanings, this is true.
+ *            Only applicable to switches.
+ */
+struct cros_ec_bs_map {
+	unsigned int ev_type;
+	unsigned int code;
+	u8 bit;
+	bool inverted;
+};
+
+/* cros_ec_keyb_bs - Map EC button/switch #defines into kernel ones */
+static const struct cros_ec_bs_map cros_ec_keyb_bs[] = {
+	/* Buttons */
+	{
+		.ev_type	= EV_KEY,
+		.code		= KEY_POWER,
+		.bit		= EC_MKBP_POWER_BUTTON,
+	},
+	{
+		.ev_type	= EV_KEY,
+		.code		= KEY_VOLUMEUP,
+		.bit		= EC_MKBP_VOL_UP,
+	},
+	{
+		.ev_type	= EV_KEY,
+		.code		= KEY_VOLUMEDOWN,
+		.bit		= EC_MKBP_VOL_DOWN,
+	},
+
+	/* Switches */
+	{
+		.ev_type	= EV_SW,
+		.code		= SW_LID,
+		.bit		= EC_MKBP_LID_OPEN,
+		.inverted	= true,
+	},
+	{
+		.ev_type	= EV_SW,
+		.code		= SW_TABLET_MODE,
+		.bit		= EC_MKBP_TABLET_MODE,
+	},
+};
+
 /*
  * Returns true when there is at least one combination of pressed keys that
  * results in ghosting.
@@ -149,20 +204,33 @@ static void cros_ec_keyb_process(struct cros_ec_keyb *ckdev,
 	input_sync(ckdev->idev);
 }
 
-static int cros_ec_keyb_open(struct input_dev *dev)
+/**
+ * cros_ec_keyb_report_bs - Report non-matrixed buttons or switches
+ *
+ * This takes a bitmap of buttons or switches from the EC and reports events,
+ * syncing at the end.
+ *
+ * @ckdev: The keyboard device.
+ * @ev_type: The input event type (e.g., EV_KEY).
+ * @mask: A bitmap of buttons from the EC.
+ */
+static void cros_ec_keyb_report_bs(struct cros_ec_keyb *ckdev,
+				   unsigned int ev_type, u32 mask)
+
 {
-	struct cros_ec_keyb *ckdev = input_get_drvdata(dev);
+	struct input_dev *idev = ckdev->bs_idev;
+	int i;
 
-	return blocking_notifier_chain_register(&ckdev->ec->event_notifier,
-						&ckdev->notifier);
-}
+	for (i = 0; i < ARRAY_SIZE(cros_ec_keyb_bs); i++) {
+		const struct cros_ec_bs_map *map = &cros_ec_keyb_bs[i];
 
-static void cros_ec_keyb_close(struct input_dev *dev)
-{
-	struct cros_ec_keyb *ckdev = input_get_drvdata(dev);
+		if (map->ev_type != ev_type)
+			continue;
 
-	blocking_notifier_chain_unregister(&ckdev->ec->event_notifier,
-					   &ckdev->notifier);
+		input_event(idev, ev_type, map->code,
+			    !!(mask & BIT(map->bit)) ^ map->inverted);
+	}
+	input_sync(idev);
 }
 
 static int cros_ec_keyb_work(struct notifier_block *nb,
@@ -170,22 +238,54 @@ static int cros_ec_keyb_work(struct notifier_block *nb,
 {
 	struct cros_ec_keyb *ckdev = container_of(nb, struct cros_ec_keyb,
 						  notifier);
+	u32 val;
+	unsigned int ev_type;
+
+	switch (ckdev->ec->event_data.event_type) {
+	case EC_MKBP_EVENT_KEY_MATRIX:
+		/*
+		 * If EC is not the wake source, discard key state changes
+		 * during suspend.
+		 */
+		if (queued_during_suspend)
+			return NOTIFY_OK;
 
-	if (ckdev->ec->event_data.event_type != EC_MKBP_EVENT_KEY_MATRIX)
+		if (ckdev->ec->event_size != ckdev->cols) {
+			dev_err(ckdev->dev,
+				"Discarded incomplete key matrix event.\n");
+			return NOTIFY_OK;
+		}
+		cros_ec_keyb_process(ckdev,
+				     ckdev->ec->event_data.data.key_matrix,
+				     ckdev->ec->event_size);
+		break;
+
+	case EC_MKBP_EVENT_BUTTON:
+	case EC_MKBP_EVENT_SWITCH:
+		/*
+		 * If EC is not the wake source, discard key state
+		 * changes during suspend. Switches will be re-checked in
+		 * cros_ec_keyb_resume() to be sure nothing is lost.
+		 */
+		if (queued_during_suspend)
+			return NOTIFY_OK;
+
+		if (ckdev->ec->event_data.event_type == EC_MKBP_EVENT_BUTTON) {
+			val = get_unaligned_le32(
+					&ckdev->ec->event_data.data.buttons);
+			ev_type = EV_KEY;
+		} else {
+			val = get_unaligned_le32(
+					&ckdev->ec->event_data.data.switches);
+			ev_type = EV_SW;
+		}
+		cros_ec_keyb_report_bs(ckdev, ev_type, val);
+		break;
+
+	default:
 		return NOTIFY_DONE;
-	/*
-	 * If EC is not the wake source, discard key state changes during
-	 * suspend.
-	 */
-	if (queued_during_suspend)
-		return NOTIFY_OK;
-	if (ckdev->ec->event_size != ckdev->cols) {
-		dev_err(ckdev->dev,
-			"Discarded incomplete key matrix event.\n");
-		return NOTIFY_OK;
 	}
-	cros_ec_keyb_process(ckdev, ckdev->ec->event_data.data.key_matrix,
-			     ckdev->ec->event_size);
+
 	return NOTIFY_OK;
 }
 
@@ -213,22 +313,228 @@ static void cros_ec_keyb_compute_valid_keys(struct cros_ec_keyb *ckdev)
 	}
 }
 
-static int cros_ec_keyb_probe(struct platform_device *pdev)
+/**
+ * cros_ec_keyb_info - Wrap the EC command EC_CMD_MKBP_INFO
+ *
+ * This wraps the EC_CMD_MKBP_INFO, abstracting out all of the marshalling and
+ * unmarshalling and different version nonsense into something simple.
+ *
+ * @ec_dev: The EC device
+ * @info_type: Either EC_MKBP_INFO_SUPPORTED or EC_MKBP_INFO_CURRENT.
+ * @event_type: Either EC_MKBP_EVENT_BUTTON or EC_MKBP_EVENT_SWITCH.  Actually
+ *              in some cases this could be EC_MKBP_EVENT_KEY_MATRIX or
+ *              EC_MKBP_EVENT_HOST_EVENT too but we don't use in this driver.
+ * @result: Where we'll store the result; a union
+ * @result_size: The size of the result.  Expected to be the size of one of
+ *               the elements in the union.
+ *
+ * Returns 0 if no error or -error upon error.
+ */
+static int cros_ec_keyb_info(struct cros_ec_device *ec_dev,
+			     enum ec_mkbp_info_type info_type,
+			     enum ec_mkbp_event event_type,
+			     union ec_response_get_next_data *result,
+			     size_t result_size)
 {
-	struct cros_ec_device *ec = dev_get_drvdata(pdev->dev.parent);
-	struct device *dev = &pdev->dev;
-	struct cros_ec_keyb *ckdev;
+	struct ec_params_mkbp_info *params;
+	struct cros_ec_command *msg;
+	int ret;
+
+	msg = kzalloc(sizeof(*msg) + max_t(size_t, result_size,
+					   sizeof(*params)), GFP_KERNEL);
+	if (!msg)
+		return -ENOMEM;
+
+	msg->command = EC_CMD_MKBP_INFO;
+	msg->version = 1;
+	msg->outsize = sizeof(*params);
+	msg->insize = result_size;
+	params = (struct ec_params_mkbp_info *)msg->data;
+	params->info_type = info_type;
+	params->event_type = event_type;
+
+	ret = cros_ec_cmd_xfer(ec_dev, msg);
+	if (ret < 0) {
+		dev_warn(ec_dev->dev, "Transfer error %d/%d: %d\n",
+			 (int)info_type, (int)event_type, ret);
+	} else if (msg->result == EC_RES_INVALID_VERSION) {
+		/* With older ECs we just return 0 for everything */
+		memset(result, 0, result_size);
+		ret = 0;
+	} else if (msg->result != EC_RES_SUCCESS) {
+		dev_warn(ec_dev->dev, "Error getting info %d/%d: %d\n",
+			 (int)info_type, (int)event_type, msg->result);
+		ret = -EPROTO;
+	} else if (ret != result_size) {
+		dev_warn(ec_dev->dev, "Wrong size %d/%d: %d != %zu\n",
+			 (int)info_type, (int)event_type,
+			 ret, result_size);
+		ret = -EPROTO;
+	} else {
+		memcpy(result, msg->data, result_size);
+		ret = 0;
+	}
+
+	kfree(msg);
+
+	return ret;
+}
+
+/**
+ * cros_ec_keyb_query_switches - Query the state of switches and report
+ *
+ * This will ask the EC about the current state of switches and report to the
+ * kernel.  Note that we don't query for buttons because they are more
+ * transitory and we'll get an update on the next release / press.
+ *
+ * @ckdev: The keyboard device
+ *
+ * Returns 0 if no error or -error upon error.
+ */
+static int cros_ec_keyb_query_switches(struct cros_ec_keyb *ckdev)
+{
+	struct cros_ec_device *ec_dev = ckdev->ec;
+	union ec_response_get_next_data event_data = {};
+	int ret;
+
+	ret = cros_ec_keyb_info(ec_dev, EC_MKBP_INFO_CURRENT,
+				EC_MKBP_EVENT_SWITCH, &event_data,
+				sizeof(event_data.switches));
+	if (ret)
+		return ret;
+
+	cros_ec_keyb_report_bs(ckdev, EV_SW,
+			       get_unaligned_le32(&event_data.switches));
+
+	return 0;
+}
+
+/**
+ * cros_ec_keyb_resume - Resume the keyboard
+ *
+ * We use the resume notification as a chance to query the EC for switches.
+ *
+ * @dev: The keyboard device
+ *
+ * Returns 0 if no error or -error upon error.
+ */
+static __maybe_unused int cros_ec_keyb_resume(struct device *dev)
+{
+	struct cros_ec_keyb *ckdev = dev_get_drvdata(dev);
+
+	if (ckdev->bs_idev)
+		return cros_ec_keyb_query_switches(ckdev);
+
+	return 0;
+}
+
+/**
+ * cros_ec_keyb_register_bs - Register non-matrix buttons/switches
+ *
+ * Handles all the bits of the keyboard driver related to non-matrix buttons
+ * and switches, including asking the EC about which are present and telling
+ * the kernel to expect them.
+ *
+ * If this device has no support for buttons and switches we'll return no error
+ * but the ckdev->bs_idev will remain NULL when this function exits.
+ *
+ * @ckdev: The keyboard device
+ *
+ * Returns 0 if no error or -error upon error.
+ */
+static int cros_ec_keyb_register_bs(struct cros_ec_keyb *ckdev)
+{
+	struct cros_ec_device *ec_dev = ckdev->ec;
+	struct device *dev = ckdev->dev;
 	struct input_dev *idev;
-	struct device_node *np;
-	int err;
+	union ec_response_get_next_data event_data = {};
+	const char *phys;
+	u32 buttons;
+	u32 switches;
+	int ret;
+	int i;
+
+	ret = cros_ec_keyb_info(ec_dev, EC_MKBP_INFO_SUPPORTED,
+				EC_MKBP_EVENT_BUTTON, &event_data,
+				sizeof(event_data.buttons));
+	if (ret)
+		return ret;
+	buttons = get_unaligned_le32(&event_data.buttons);
+
+	ret = cros_ec_keyb_info(ec_dev, EC_MKBP_INFO_SUPPORTED,
+				EC_MKBP_EVENT_SWITCH, &event_data,
+				sizeof(event_data.switches));
+	if (ret)
+		return ret;
+	switches = get_unaligned_le32(&event_data.switches);
+
+	if (!buttons && !switches)
+		return 0;
 
-	np = pdev->dev.of_node;
-	if (!np)
-		return -ENODEV;
+	/*
+	 * We call the non-matrix buttons/switches 'input1', if present.
+	 * Allocate phys before input dev, to ensure correct tear-down
+	 * ordering.
+	 */
+	phys = devm_kasprintf(dev, GFP_KERNEL, "%s/input1", ec_dev->phys_name);
+	if (!phys)
+		return -ENOMEM;
 
-	ckdev = devm_kzalloc(dev, sizeof(*ckdev), GFP_KERNEL);
-	if (!ckdev)
+	idev = devm_input_allocate_device(dev);
+	if (!idev)
 		return -ENOMEM;
+
+	idev->name = "cros_ec_buttons";
+	idev->phys = phys;
+	__set_bit(EV_REP, idev->evbit);
+
+	idev->id.bustype = BUS_VIRTUAL;
+	idev->id.version = 1;
+	idev->id.product = 0;
+	idev->dev.parent = dev;
+
+	input_set_drvdata(idev, ckdev);
+	ckdev->bs_idev = idev;
+
+	for (i = 0; i < ARRAY_SIZE(cros_ec_keyb_bs); i++) {
+		const struct cros_ec_bs_map *map = &cros_ec_keyb_bs[i];
+
+		if (buttons & BIT(map->bit))
+			input_set_capability(idev, map->ev_type, map->code);
+	}
+
+	ret = cros_ec_keyb_query_switches(ckdev);
+	if (ret) {
+		dev_err(dev, "cannot query switches\n");
+		return ret;
+	}
+
+	ret = input_register_device(ckdev->bs_idev);
+	if (ret) {
+		dev_err(dev, "cannot register input device\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * cros_ec_keyb_register_bs - Register matrix keys
+ *
+ * Handles all the bits of the keyboard driver related to matrix keys.
+ *
+ * @ckdev: The keyboard device
+ *
+ * Returns 0 if no error or -error upon error.
+ */
+static int cros_ec_keyb_register_matrix(struct cros_ec_keyb *ckdev)
+{
+	struct cros_ec_device *ec_dev = ckdev->ec;
+	struct device *dev = ckdev->dev;
+	struct input_dev *idev;
+	const char *phys;
+	int err;
+
 	err = matrix_keypad_parse_of_params(dev, &ckdev->rows, &ckdev->cols);
 	if (err)
 		return err;
@@ -241,27 +547,28 @@ static int cros_ec_keyb_probe(struct platform_device *pdev)
 	if (!ckdev->old_kb_state)
 		return -ENOMEM;
 
+	/*
+	 * We call the keyboard matrix 'input0'. Allocate phys before input
+	 * dev, to ensure correct tear-down ordering.
+	 */
+	phys = devm_kasprintf(dev, GFP_KERNEL, "%s/input0", ec_dev->phys_name);
+	if (!phys)
+		return -ENOMEM;
+
 	idev = devm_input_allocate_device(dev);
 	if (!idev)
 		return -ENOMEM;
 
-	ckdev->ec = ec;
-	ckdev->notifier.notifier_call = cros_ec_keyb_work;
-	ckdev->dev = dev;
-	dev_set_drvdata(dev, ckdev);
-
 	idev->name = CROS_EC_DEV_NAME;
-	idev->phys = ec->phys_name;
+	idev->phys = phys;
 	__set_bit(EV_REP, idev->evbit);
 
 	idev->id.bustype = BUS_VIRTUAL;
 	idev->id.version = 1;
 	idev->id.product = 0;
 	idev->dev.parent = dev;
-	idev->open = cros_ec_keyb_open;
-	idev->close = cros_ec_keyb_close;
 
-	ckdev->ghost_filter = of_property_read_bool(np,
+	ckdev->ghost_filter = of_property_read_bool(dev->of_node,
 					"google,needs-ghost-filter");
 
 	err = matrix_keypad_build_keymap(NULL, NULL, ckdev->rows, ckdev->cols,
@@ -287,6 +594,57 @@ static int cros_ec_keyb_probe(struct platform_device *pdev)
 	return 0;
 }
 
+static int cros_ec_keyb_probe(struct platform_device *pdev)
+{
+	struct cros_ec_device *ec = dev_get_drvdata(pdev->dev.parent);
+	struct device *dev = &pdev->dev;
+	struct cros_ec_keyb *ckdev;
+	int err;
+
+	if (!dev->of_node)
+		return -ENODEV;
+
+	ckdev = devm_kzalloc(dev, sizeof(*ckdev), GFP_KERNEL);
+	if (!ckdev)
+		return -ENOMEM;
+
+	ckdev->ec = ec;
+	ckdev->dev = dev;
+	dev_set_drvdata(dev, ckdev);
+
+	err = cros_ec_keyb_register_matrix(ckdev);
+	if (err) {
+		dev_err(dev, "cannot register matrix inputs: %d\n", err);
+		return err;
+	}
+
+	err = cros_ec_keyb_register_bs(ckdev);
+	if (err) {
+		dev_err(dev, "cannot register non-matrix inputs: %d\n", err);
+		return err;
+	}
+
+	ckdev->notifier.notifier_call = cros_ec_keyb_work;
+	err = blocking_notifier_chain_register(&ckdev->ec->event_notifier,
+					       &ckdev->notifier);
+	if (err) {
+		dev_err(dev, "cannot register notifier: %d\n", err);
+		return err;
+	}
+
+	return 0;
+}
+
+static int cros_ec_keyb_remove(struct platform_device *pdev)
+{
+	struct cros_ec_keyb *ckdev = dev_get_drvdata(&pdev->dev);
+
+	blocking_notifier_chain_unregister(&ckdev->ec->event_notifier,
+					   &ckdev->notifier);
+
+	return 0;
+}
+
 #ifdef CONFIG_OF
 static const struct of_device_id cros_ec_keyb_of_match[] = {
 	{ .compatible = "google,cros-ec-keyb" },
@@ -295,11 +653,15 @@ static const struct of_device_id cros_ec_keyb_of_match[] = {
 MODULE_DEVICE_TABLE(of, cros_ec_keyb_of_match);
 #endif
 
+static const SIMPLE_DEV_PM_OPS(cros_ec_keyb_pm_ops, NULL, cros_ec_keyb_resume);
+
 static struct platform_driver cros_ec_keyb_driver = {
 	.probe = cros_ec_keyb_probe,
+	.remove = cros_ec_keyb_remove,
 	.driver = {
 		.name = "cros-ec-keyb",
 		.of_match_table = of_match_ptr(cros_ec_keyb_of_match),
+		.pm = &cros_ec_keyb_pm_ops,
 	},
 };
 

drivers/mfd/lpc_ich.c

@@ -56,6 +56,7 @@
  *	document number TBD : Wildcat Point-LP
  *	document number TBD : 9 Series
  *	document number TBD : Lewisburg
+ *	document number TBD : Apollo Lake SoC
  */
 
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
@@ -83,6 +84,17 @@
 #define ACPIBASE_GCS_OFF	0x3410
 #define ACPIBASE_GCS_END	0x3414
 
+#define SPIBASE_BYT		0x54
+#define SPIBASE_BYT_SZ		512
+#define SPIBASE_BYT_EN		BIT(1)
+
+#define SPIBASE_LPT		0x3800
+#define SPIBASE_LPT_SZ		512
+#define BCR			0xdc
+#define BCR_WPD			BIT(0)
+
+#define SPIBASE_APL_SZ		4096
+
 #define GPIOBASE_ICH0		0x58
 #define GPIOCTRL_ICH0		0x5C
 #define GPIOBASE_ICH6		0x48
@@ -133,6 +145,12 @@ static struct resource gpio_ich_res[] = {
 	},
 };
 
+static struct resource intel_spi_res[] = {
+	{
+		.flags = IORESOURCE_MEM,
+	}
+};
+
 static struct mfd_cell lpc_ich_wdt_cell = {
 	.name = "iTCO_wdt",
 	.num_resources = ARRAY_SIZE(wdt_ich_res),
@@ -147,6 +165,14 @@ static struct mfd_cell lpc_ich_gpio_cell = {
 	.ignore_resource_conflicts = true,
 };
 
+
+static struct mfd_cell lpc_ich_spi_cell = {
+	.name = "intel-spi",
+	.num_resources = ARRAY_SIZE(intel_spi_res),
+	.resources = intel_spi_res,
+	.ignore_resource_conflicts = true,
+};
+
 /* chipset related info */
 enum lpc_chipsets {
 	LPC_ICH = 0,	/* ICH */
@@ -216,6 +242,7 @@ enum lpc_chipsets {
 	LPC_BRASWELL,	/* Braswell SoC */
 	LPC_LEWISBURG,	/* Lewisburg */
 	LPC_9S,		/* 9 Series */
+	LPC_APL,	/* Apollo Lake SoC */
 };
 
 static struct lpc_ich_info lpc_chipset_info[] = {
@@ -494,10 +521,12 @@ static struct lpc_ich_info lpc_chipset_info[] = {
 		.name = "Lynx Point",
 		.iTCO_version = 2,
 		.gpio_version = ICH_V5_GPIO,
+		.spi_type = INTEL_SPI_LPT,
 	},
 	[LPC_LPT_LP] = {
 		.name = "Lynx Point_LP",
 		.iTCO_version = 2,
+		.spi_type = INTEL_SPI_LPT,
 	},
 	[LPC_WBG] = {
 		.name = "Wellsburg",
@@ -511,6 +540,7 @@ static struct lpc_ich_info lpc_chipset_info[] = {
 	[LPC_BAYTRAIL] = {
 		.name = "Bay Trail SoC",
 		.iTCO_version = 3,
+		.spi_type = INTEL_SPI_BYT,
 	},
 	[LPC_COLETO] = {
 		.name = "Coleto Creek",
@@ -519,10 +549,12 @@ static struct lpc_ich_info lpc_chipset_info[] = {
 	[LPC_WPT_LP] = {
 		.name = "Wildcat Point_LP",
 		.iTCO_version = 2,
+		.spi_type = INTEL_SPI_LPT,
 	},
 	[LPC_BRASWELL] = {
 		.name = "Braswell SoC",
 		.iTCO_version = 3,
+		.spi_type = INTEL_SPI_BYT,
 	},
 	[LPC_LEWISBURG] = {
 		.name = "Lewisburg",
@@ -533,6 +565,10 @@ static struct lpc_ich_info lpc_chipset_info[] = {
 		.iTCO_version = 2,
 		.gpio_version = ICH_V5_GPIO,
 	},
+	[LPC_APL] = {
+		.name = "Apollo Lake SoC",
+		.spi_type = INTEL_SPI_BXT,
+	},
 };
 
 /*
@@ -681,6 +717,7 @@ static const struct pci_device_id lpc_ich_ids[] = {
 	{ PCI_VDEVICE(INTEL, 0x3b14), LPC_3420},
 	{ PCI_VDEVICE(INTEL, 0x3b16), LPC_3450},
 	{ PCI_VDEVICE(INTEL, 0x5031), LPC_EP80579},
+	{ PCI_VDEVICE(INTEL, 0x5ae8), LPC_APL},
 	{ PCI_VDEVICE(INTEL, 0x8c40), LPC_LPT},
 	{ PCI_VDEVICE(INTEL, 0x8c41), LPC_LPT},
 	{ PCI_VDEVICE(INTEL, 0x8c42), LPC_LPT},
@@ -1056,6 +1093,94 @@ static int lpc_ich_init_wdt(struct pci_dev *dev)
 	return ret;
 }
 
+static int lpc_ich_init_spi(struct pci_dev *dev)
+{
+	struct lpc_ich_priv *priv = pci_get_drvdata(dev);
+	struct resource *res = &intel_spi_res[0];
+	struct intel_spi_boardinfo *info;
+	u32 spi_base, rcba, bcr;
+
+	info = devm_kzalloc(&dev->dev, sizeof(*info), GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	info->type = lpc_chipset_info[priv->chipset].spi_type;
+
+	switch (info->type) {
+	case INTEL_SPI_BYT:
+		pci_read_config_dword(dev, SPIBASE_BYT, &spi_base);
+		if (spi_base & SPIBASE_BYT_EN) {
+			res->start = spi_base & ~(SPIBASE_BYT_SZ - 1);
+			res->end = res->start + SPIBASE_BYT_SZ - 1;
+		}
+		break;
+
+	case INTEL_SPI_LPT:
+		pci_read_config_dword(dev, RCBABASE, &rcba);
+		if (rcba & 1) {
+			spi_base = round_down(rcba, SPIBASE_LPT_SZ);
+			res->start = spi_base + SPIBASE_LPT;
+			res->end = res->start + SPIBASE_LPT_SZ - 1;
+
+			/*
+			 * Try to make the flash chip writeable now by
+			 * setting BCR_WPD. It it fails we tell the driver
+			 * that it can only read the chip.
+			 */
+			pci_read_config_dword(dev, BCR, &bcr);
+			if (!(bcr & BCR_WPD)) {
+				bcr |= BCR_WPD;
+				pci_write_config_dword(dev, BCR, bcr);
+				pci_read_config_dword(dev, BCR, &bcr);
+			}
+			info->writeable = !!(bcr & BCR_WPD);
+		}
+		break;
+
+	case INTEL_SPI_BXT: {
+		unsigned int p2sb = PCI_DEVFN(13, 0);
+		unsigned int spi = PCI_DEVFN(13, 2);
+		struct pci_bus *bus = dev->bus;
+
+		/*
+		 * The P2SB is hidden by BIOS and we need to unhide it in
+		 * order to read BAR of the SPI flash device. Once that is
+		 * done we hide it again.
+		 */
+		pci_bus_write_config_byte(bus, p2sb, 0xe1, 0x0);
+		pci_bus_read_config_dword(bus, spi, PCI_BASE_ADDRESS_0,
+					  &spi_base);
+		if (spi_base != ~0) {
+			res->start = spi_base & 0xfffffff0;
+			res->end = res->start + SPIBASE_APL_SZ - 1;
+
+			pci_bus_read_config_dword(bus, spi, BCR, &bcr);
+			if (!(bcr & BCR_WPD)) {
+				bcr |= BCR_WPD;
+				pci_bus_write_config_dword(bus, spi, BCR, bcr);
+				pci_bus_read_config_dword(bus, spi, BCR, &bcr);
+			}
+			info->writeable = !!(bcr & BCR_WPD);
+		}
+
+		pci_bus_write_config_byte(bus, p2sb, 0xe1, 0x1);
+		break;
+	}
+
+	default:
+		return -EINVAL;
+	}
+
+	if (!res->start)
+		return -ENODEV;
+
+	lpc_ich_spi_cell.platform_data = info;
+	lpc_ich_spi_cell.pdata_size = sizeof(*info);
+
+	return mfd_add_devices(&dev->dev, PLATFORM_DEVID_NONE,
+			       &lpc_ich_spi_cell, 1, NULL, 0, NULL);
+}
+
 static int lpc_ich_probe(struct pci_dev *dev,
 				const struct pci_device_id *id)
 {
@@ -1099,6 +1224,12 @@ static int lpc_ich_probe(struct pci_dev *dev,
 			cell_added = true;
 	}
 
+	if (lpc_chipset_info[priv->chipset].spi_type) {
+		ret = lpc_ich_init_spi(dev);
+		if (!ret)
+			cell_added = true;
+	}
+
 	/*
 	 * We only care if at least one or none of the cells registered
 	 * successfully.

drivers/mtd/spi-nor/Kconfig

@@ -76,4 +76,24 @@ config SPI_NXP_SPIFI
 	  Flash. Enable this option if you have a device with a SPIFI
 	  controller and want to access the Flash as a mtd device.
 
+config SPI_INTEL_SPI
+	tristate
+
+config SPI_INTEL_SPI_PLATFORM
+	tristate "Intel PCH/PCU SPI flash platform driver" if EXPERT
+	depends on X86
+	select SPI_INTEL_SPI
+	help
+	  This enables platform support for the Intel PCH/PCU SPI
+	  controller in master mode. This controller is present in modern
+	  Intel hardware and is used to hold BIOS and other persistent
+	  settings. Using this driver it is possible to upgrade BIOS
+	  directly from Linux.
+
+	  Say N here unless you know what you are doing. Overwriting the
+	  SPI flash may render the system unbootable.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called intel-spi-platform.
+
 endif # MTD_SPI_NOR

drivers/mtd/spi-nor/Makefile

@@ -5,3 +5,5 @@ obj-$(CONFIG_SPI_FSL_QUADSPI)	+= fsl-quadspi.o
 obj-$(CONFIG_SPI_HISI_SFC)	+= hisi-sfc.o
 obj-$(CONFIG_MTD_MT81xx_NOR)    += mtk-quadspi.o
 obj-$(CONFIG_SPI_NXP_SPIFI)	+= nxp-spifi.o
+obj-$(CONFIG_SPI_INTEL_SPI)	+= intel-spi.o
+obj-$(CONFIG_SPI_INTEL_SPI_PLATFORM)	+= intel-spi-platform.o

drivers/mtd/spi-nor/intel-spi-platform.c

+/*
+ * Intel PCH/PCU SPI flash platform driver.
+ *
+ * Copyright (C) 2016, Intel Corporation
+ * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/ioport.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include "intel-spi.h"
+
+static int intel_spi_platform_probe(struct platform_device *pdev)
+{
+	struct intel_spi_boardinfo *info;
+	struct intel_spi *ispi;
+	struct resource *mem;
+
+	info = dev_get_platdata(&pdev->dev);
+	if (!info)
+		return -EINVAL;
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	ispi = intel_spi_probe(&pdev->dev, mem, info);
+	if (IS_ERR(ispi))
+		return PTR_ERR(ispi);
+
+	platform_set_drvdata(pdev, ispi);
+	return 0;
+}
+
+static int intel_spi_platform_remove(struct platform_device *pdev)
+{
+	struct intel_spi *ispi = platform_get_drvdata(pdev);
+
+	return intel_spi_remove(ispi);
+}
+
+static struct platform_driver intel_spi_platform_driver = {
+	.probe = intel_spi_platform_probe,
+	.remove = intel_spi_platform_remove,
+	.driver = {
+		.name = "intel-spi",
+	},
+};
+
+module_platform_driver(intel_spi_platform_driver);
+
+MODULE_DESCRIPTION("Intel PCH/PCU SPI flash platform driver");
+MODULE_AUTHOR("Mika Westerberg <mika.westerberg@linux.intel.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:intel-spi");

drivers/mtd/spi-nor/intel-spi.c

+/*
+ * Intel PCH/PCU SPI flash driver.
+ *
+ * Copyright (C) 2016, Intel Corporation
+ * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/sched.h>
+#include <linux/sizes.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/spi-nor.h>
+#include <linux/platform_data/intel-spi.h>
+
+#include "intel-spi.h"
+
+/* Offsets are from @ispi->base */
+#define BFPREG				0x00
+
+#define HSFSTS_CTL			0x04
+#define HSFSTS_CTL_FSMIE		BIT(31)
+#define HSFSTS_CTL_FDBC_SHIFT		24
+#define HSFSTS_CTL_FDBC_MASK		(0x3f << HSFSTS_CTL_FDBC_SHIFT)
+
+#define HSFSTS_CTL_FCYCLE_SHIFT		17
+#define HSFSTS_CTL_FCYCLE_MASK		(0x0f << HSFSTS_CTL_FCYCLE_SHIFT)
+/* HW sequencer opcodes */
+#define HSFSTS_CTL_FCYCLE_READ		(0x00 << HSFSTS_CTL_FCYCLE_SHIFT)
+#define HSFSTS_CTL_FCYCLE_WRITE		(0x02 << HSFSTS_CTL_FCYCLE_SHIFT)
+#define HSFSTS_CTL_FCYCLE_ERASE		(0x03 << HSFSTS_CTL_FCYCLE_SHIFT)
+#define HSFSTS_CTL_FCYCLE_ERASE_64K	(0x04 << HSFSTS_CTL_FCYCLE_SHIFT)
+#define HSFSTS_CTL_FCYCLE_RDID		(0x06 << HSFSTS_CTL_FCYCLE_SHIFT)
+#define HSFSTS_CTL_FCYCLE_WRSR		(0x07 << HSFSTS_CTL_FCYCLE_SHIFT)
+#define HSFSTS_CTL_FCYCLE_RDSR		(0x08 << HSFSTS_CTL_FCYCLE_SHIFT)
+
+#define HSFSTS_CTL_FGO			BIT(16)
+#define HSFSTS_CTL_FLOCKDN		BIT(15)
+#define HSFSTS_CTL_FDV			BIT(14)
+#define HSFSTS_CTL_SCIP			BIT(5)
+#define HSFSTS_CTL_AEL			BIT(2)
+#define HSFSTS_CTL_FCERR		BIT(1)
+#define HSFSTS_CTL_FDONE		BIT(0)
+
+#define FADDR				0x08
+#define DLOCK				0x0c
+#define FDATA(n)			(0x10 + ((n) * 4))
+
+#define FRACC				0x50
+
+#define FREG(n)				(0x54 + ((n) * 4))
+#define FREG_BASE_MASK			0x3fff
+#define FREG_LIMIT_SHIFT		16
+#define FREG_LIMIT_MASK			(0x03fff << FREG_LIMIT_SHIFT)
+
+/* Offset is from @ispi->pregs */
+#define PR(n)				((n) * 4)
+#define PR_WPE				BIT(31)
+#define PR_LIMIT_SHIFT			16
+#define PR_LIMIT_MASK			(0x3fff << PR_LIMIT_SHIFT)
+#define PR_RPE				BIT(15)
+#define PR_BASE_MASK			0x3fff
+/* Last PR is GPR0 */
+#define PR_NUM				(5 + 1)
+
+/* Offsets are from @ispi->sregs */
+#define SSFSTS_CTL			0x00
+#define SSFSTS_CTL_FSMIE		BIT(23)
+#define SSFSTS_CTL_DS			BIT(22)
+#define SSFSTS_CTL_DBC_SHIFT		16
+#define SSFSTS_CTL_SPOP			BIT(11)
+#define SSFSTS_CTL_ACS			BIT(10)
+#define SSFSTS_CTL_SCGO			BIT(9)
+#define SSFSTS_CTL_COP_SHIFT		12
+#define SSFSTS_CTL_FRS			BIT(7)
+#define SSFSTS_CTL_DOFRS		BIT(6)
+#define SSFSTS_CTL_AEL			BIT(4)
+#define SSFSTS_CTL_FCERR		BIT(3)
+#define SSFSTS_CTL_FDONE		BIT(2)
+#define SSFSTS_CTL_SCIP			BIT(0)
+
+#define PREOP_OPTYPE			0x04
+#define OPMENU0				0x08
+#define OPMENU1				0x0c
+
+/* CPU specifics */
+#define BYT_PR				0x74
+#define BYT_SSFSTS_CTL			0x90
+#define BYT_BCR				0xfc
+#define BYT_BCR_WPD			BIT(0)
+#define BYT_FREG_NUM			5
+
+#define LPT_PR				0x74
+#define LPT_SSFSTS_CTL			0x90
+#define LPT_FREG_NUM			5
+
+#define BXT_PR				0x84
+#define BXT_SSFSTS_CTL			0xa0
+#define BXT_FREG_NUM			12
+
+#define INTEL_SPI_TIMEOUT		5000 /* ms */
+#define INTEL_SPI_FIFO_SZ		64
+
+/**
+ * struct intel_spi - Driver private data
+ * @dev: Device pointer
+ * @info: Pointer to board specific info
+ * @nor: SPI NOR layer structure
+ * @base: Beginning of MMIO space
+ * @pregs: Start of protection registers
+ * @sregs: Start of software sequencer registers
+ * @nregions: Maximum number of regions
+ * @writeable: Is the chip writeable
+ * @swseq: Use SW sequencer in register reads/writes
+ * @erase_64k: 64k erase supported
+ * @opcodes: Opcodes which are supported. This are programmed by BIOS
+ *           before it locks down the controller.
+ * @preopcodes: Preopcodes which are supported.
+ */
+struct intel_spi {
+	struct device *dev;
+	const struct intel_spi_boardinfo *info;
+	struct spi_nor nor;
+	void __iomem *base;
+	void __iomem *pregs;
+	void __iomem *sregs;
+	size_t nregions;
+	bool writeable;
+	bool swseq;
+	bool erase_64k;
+	u8 opcodes[8];
+	u8 preopcodes[2];
+};
+
+static bool writeable;
+module_param(writeable, bool, 0);
+MODULE_PARM_DESC(writeable, "Enable write access to SPI flash chip (default=0)");
+
+static void intel_spi_dump_regs(struct intel_spi *ispi)
+{
+	u32 value;
+	int i;
+
+	dev_dbg(ispi->dev, "BFPREG=0x%08x\n", readl(ispi->base + BFPREG));
+
+	value = readl(ispi->base + HSFSTS_CTL);
+	dev_dbg(ispi->dev, "HSFSTS_CTL=0x%08x\n", value);
+	if (value & HSFSTS_CTL_FLOCKDN)
+		dev_dbg(ispi->dev, "-> Locked\n");
+
+	dev_dbg(ispi->dev, "FADDR=0x%08x\n", readl(ispi->base + FADDR));
+	dev_dbg(ispi->dev, "DLOCK=0x%08x\n", readl(ispi->base + DLOCK));
+
+	for (i = 0; i < 16; i++)
+		dev_dbg(ispi->dev, "FDATA(%d)=0x%08x\n",
+			i, readl(ispi->base + FDATA(i)));
+
+	dev_dbg(ispi->dev, "FRACC=0x%08x\n", readl(ispi->base + FRACC));
+
+	for (i = 0; i < ispi->nregions; i++)
+		dev_dbg(ispi->dev, "FREG(%d)=0x%08x\n", i,
+			readl(ispi->base + FREG(i)));
+	for (i = 0; i < PR_NUM; i++)
+		dev_dbg(ispi->dev, "PR(%d)=0x%08x\n", i,
+			readl(ispi->pregs + PR(i)));
+
+	value = readl(ispi->sregs + SSFSTS_CTL);
+	dev_dbg(ispi->dev, "SSFSTS_CTL=0x%08x\n", value);
+	dev_dbg(ispi->dev, "PREOP_OPTYPE=0x%08x\n",
+		readl(ispi->sregs + PREOP_OPTYPE));
+	dev_dbg(ispi->dev, "OPMENU0=0x%08x\n", readl(ispi->sregs + OPMENU0));
+	dev_dbg(ispi->dev, "OPMENU1=0x%08x\n", readl(ispi->sregs + OPMENU1));
+
+	if (ispi->info->type == INTEL_SPI_BYT)
+		dev_dbg(ispi->dev, "BCR=0x%08x\n", readl(ispi->base + BYT_BCR));
+
+	dev_dbg(ispi->dev, "Protected regions:\n");
+	for (i = 0; i < PR_NUM; i++) {
+		u32 base, limit;
+
+		value = readl(ispi->pregs + PR(i));
+		if (!(value & (PR_WPE | PR_RPE)))
+			continue;
+
+		limit = (value & PR_LIMIT_MASK) >> PR_LIMIT_SHIFT;
+		base = value & PR_BASE_MASK;
+
+		dev_dbg(ispi->dev, " %02d base: 0x%08x limit: 0x%08x [%c%c]\n",
+			 i, base << 12, (limit << 12) | 0xfff,
+			 value & PR_WPE ? 'W' : '.',
+			 value & PR_RPE ? 'R' : '.');
+	}
+
+	dev_dbg(ispi->dev, "Flash regions:\n");
+	for (i = 0; i < ispi->nregions; i++) {
+		u32 region, base, limit;
+
+		region = readl(ispi->base + FREG(i));
+		base = region & FREG_BASE_MASK;
+		limit = (region & FREG_LIMIT_MASK) >> FREG_LIMIT_SHIFT;
+
+		if (base >= limit || (i > 0 && limit == 0))
+			dev_dbg(ispi->dev, " %02d disabled\n", i);
+		else
+			dev_dbg(ispi->dev, " %02d base: 0x%08x limit: 0x%08x\n",
+				 i, base << 12, (limit << 12) | 0xfff);
+	}
+
+	dev_dbg(ispi->dev, "Using %cW sequencer for register access\n",
+		ispi->swseq ? 'S' : 'H');
+}
+
+/* Reads max INTEL_SPI_FIFO_SZ bytes from the device fifo */
+static int intel_spi_read_block(struct intel_spi *ispi, void *buf, size_t size)
+{
+	size_t bytes;
+	int i = 0;
+
+	if (size > INTEL_SPI_FIFO_SZ)
+		return -EINVAL;
+
+	while (size > 0) {
+		bytes = min_t(size_t, size, 4);
+		memcpy_fromio(buf, ispi->base + FDATA(i), bytes);
+		size -= bytes;
+		buf += bytes;
+		i++;
+	}
+
+	return 0;
+}
+
+/* Writes max INTEL_SPI_FIFO_SZ bytes to the device fifo */
+static int intel_spi_write_block(struct intel_spi *ispi, const void *buf,
+				 size_t size)
+{
+	size_t bytes;
+	int i = 0;
+
+	if (size > INTEL_SPI_FIFO_SZ)
+		return -EINVAL;
+
+	while (size > 0) {
+		bytes = min_t(size_t, size, 4);
+		memcpy_toio(ispi->base + FDATA(i), buf, bytes);
+		size -= bytes;
+		buf += bytes;
+		i++;
+	}
+
+	return 0;
+}
+
+static int intel_spi_wait_hw_busy(struct intel_spi *ispi)
+{
+	u32 val;
+
+	return readl_poll_timeout(ispi->base + HSFSTS_CTL, val,
+				  !(val & HSFSTS_CTL_SCIP), 0,
+				  INTEL_SPI_TIMEOUT * 1000);
+}
+
+static int intel_spi_wait_sw_busy(struct intel_spi *ispi)
+{
+	u32 val;
+
+	return readl_poll_timeout(ispi->sregs + SSFSTS_CTL, val,
+				  !(val & SSFSTS_CTL_SCIP), 0,
+				  INTEL_SPI_TIMEOUT * 1000);
+}
+
+static int intel_spi_init(struct intel_spi *ispi)
+{
+	u32 opmenu0, opmenu1, val;
+	int i;
+
+	switch (ispi->info->type) {
+	case INTEL_SPI_BYT:
+		ispi->sregs = ispi->base + BYT_SSFSTS_CTL;
+		ispi->pregs = ispi->base + BYT_PR;
+		ispi->nregions = BYT_FREG_NUM;
+
+		if (writeable) {
+			/* Disable write protection */
+			val = readl(ispi->base + BYT_BCR);
+			if (!(val & BYT_BCR_WPD)) {
+				val |= BYT_BCR_WPD;
+				writel(val, ispi->base + BYT_BCR);
+				val = readl(ispi->base + BYT_BCR);
+			}
+
+			ispi->writeable = !!(val & BYT_BCR_WPD);
+		}
+
+		break;
+
+	case INTEL_SPI_LPT:
+		ispi->sregs = ispi->base + LPT_SSFSTS_CTL;
+		ispi->pregs = ispi->base + LPT_PR;
+		ispi->nregions = LPT_FREG_NUM;
+		break;
+
+	case INTEL_SPI_BXT:
+		ispi->sregs = ispi->base + BXT_SSFSTS_CTL;
+		ispi->pregs = ispi->base + BXT_PR;
+		ispi->nregions = BXT_FREG_NUM;
+		ispi->erase_64k = true;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	/* Disable #SMI generation */
+	val = readl(ispi->base + HSFSTS_CTL);
+	val &= ~HSFSTS_CTL_FSMIE;
+	writel(val, ispi->base + HSFSTS_CTL);
+
+	/*
+	 * BIOS programs allowed opcodes and then locks down the register.
+	 * So read back what opcodes it decided to support. That's the set
+	 * we are going to support as well.
+	 */
+	opmenu0 = readl(ispi->sregs + OPMENU0);
+	opmenu1 = readl(ispi->sregs + OPMENU1);
+
+	/*
+	 * Some controllers can only do basic operations using hardware
+	 * sequencer. All other operations are supposed to be carried out
+	 * using software sequencer. If we find that BIOS has programmed
+	 * opcodes for the software sequencer we use that over the hardware
+	 * sequencer.
+	 */
+	if (opmenu0 && opmenu1) {
+		for (i = 0; i < ARRAY_SIZE(ispi->opcodes) / 2; i++) {
+			ispi->opcodes[i] = opmenu0 >> i * 8;
+			ispi->opcodes[i + 4] = opmenu1 >> i * 8;
+		}
+
+		val = readl(ispi->sregs + PREOP_OPTYPE);
+		ispi->preopcodes[0] = val;
+		ispi->preopcodes[1] = val >> 8;
+
+		/* Disable #SMI generation from SW sequencer */
+		val = readl(ispi->sregs + SSFSTS_CTL);
+		val &= ~SSFSTS_CTL_FSMIE;
+		writel(val, ispi->sregs + SSFSTS_CTL);
+
+		ispi->swseq = true;
+	}
+
+	intel_spi_dump_regs(ispi);
+
+	return 0;
+}
+
+static int intel_spi_opcode_index(struct intel_spi *ispi, u8 opcode)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(ispi->opcodes); i++)
+		if (ispi->opcodes[i] == opcode)
+			return i;
+	return -EINVAL;
+}
+
+static int intel_spi_hw_cycle(struct intel_spi *ispi, u8 opcode, u8 *buf,
+			      int len)
+{
+	u32 val, status;
+	int ret;
+
+	val = readl(ispi->base + HSFSTS_CTL);
+	val &= ~(HSFSTS_CTL_FCYCLE_MASK | HSFSTS_CTL_FDBC_MASK);
+
+	switch (opcode) {
+	case SPINOR_OP_RDID:
+		val |= HSFSTS_CTL_FCYCLE_RDID;
+		break;
+	case SPINOR_OP_WRSR:
+		val |= HSFSTS_CTL_FCYCLE_WRSR;
+		break;
+	case SPINOR_OP_RDSR:
+		val |= HSFSTS_CTL_FCYCLE_RDSR;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	val |= (len - 1) << HSFSTS_CTL_FDBC_SHIFT;
+	val |= HSFSTS_CTL_FCERR | HSFSTS_CTL_FDONE;
+	val |= HSFSTS_CTL_FGO;
+	writel(val, ispi->base + HSFSTS_CTL);
+
+	ret = intel_spi_wait_hw_busy(ispi);
+	if (ret)
+		return ret;
+
+	status = readl(ispi->base + HSFSTS_CTL);
+	if (status & HSFSTS_CTL_FCERR)
+		return -EIO;
+	else if (status & HSFSTS_CTL_AEL)
+		return -EACCES;
+
+	return 0;
+}
+
+static int intel_spi_sw_cycle(struct intel_spi *ispi, u8 opcode, u8 *buf,
+			      int len)
+{
+	u32 val, status;
+	int ret;
+
+	ret = intel_spi_opcode_index(ispi, opcode);
+	if (ret < 0)
+		return ret;
+
+	val = (len << SSFSTS_CTL_DBC_SHIFT) | SSFSTS_CTL_DS;
+	val |= ret << SSFSTS_CTL_COP_SHIFT;
+	val |= SSFSTS_CTL_FCERR | SSFSTS_CTL_FDONE;
+	val |= SSFSTS_CTL_SCGO;
+	writel(val, ispi->sregs + SSFSTS_CTL);
+
+	ret = intel_spi_wait_sw_busy(ispi);
+	if (ret)
+		return ret;
+
+	status = readl(ispi->base + SSFSTS_CTL);
+	if (status & SSFSTS_CTL_FCERR)
+		return -EIO;
+	else if (status & SSFSTS_CTL_AEL)
+		return -EACCES;
+
+	return 0;
+}
+
+static int intel_spi_read_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
+{
+	struct intel_spi *ispi = nor->priv;
+	int ret;
+
+	/* Address of the first chip */
+	writel(0, ispi->base + FADDR);
+
+	if (ispi->swseq)
+		ret = intel_spi_sw_cycle(ispi, opcode, buf, len);
+	else
+		ret = intel_spi_hw_cycle(ispi, opcode, buf, len);
+
+	if (ret)
+		return ret;
+
+	return intel_spi_read_block(ispi, buf, len);
+}
+
+static int intel_spi_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
+{
+	struct intel_spi *ispi = nor->priv;
+	int ret;
+
+	/*
+	 * This is handled with atomic operation and preop code in Intel
+	 * controller so skip it here now.
+	 */
+	if (opcode == SPINOR_OP_WREN)
+		return 0;
+
+	writel(0, ispi->base + FADDR);
+
+	/* Write the value beforehand */
+	ret = intel_spi_write_block(ispi, buf, len);
+	if (ret)
+		return ret;
+
+	if (ispi->swseq)
+		return intel_spi_sw_cycle(ispi, opcode, buf, len);
+	return intel_spi_hw_cycle(ispi, opcode, buf, len);
+}
+
+static ssize_t intel_spi_read(struct spi_nor *nor, loff_t from, size_t len,
+			      u_char *read_buf)
+{
+	struct intel_spi *ispi = nor->priv;
+	size_t block_size, retlen = 0;
+	u32 val, status;
+	ssize_t ret;
+
+	switch (nor->read_opcode) {
+	case SPINOR_OP_READ:
+	case SPINOR_OP_READ_FAST:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	while (len > 0) {
+		block_size = min_t(size_t, len, INTEL_SPI_FIFO_SZ);
+
+		writel(from, ispi->base + FADDR);
+
+		val = readl(ispi->base + HSFSTS_CTL);
+		val &= ~(HSFSTS_CTL_FDBC_MASK | HSFSTS_CTL_FCYCLE_MASK);
+		val |= HSFSTS_CTL_AEL | HSFSTS_CTL_FCERR | HSFSTS_CTL_FDONE;
+		val |= (block_size - 1) << HSFSTS_CTL_FDBC_SHIFT;
+		val |= HSFSTS_CTL_FCYCLE_READ;
+		val |= HSFSTS_CTL_FGO;
+		writel(val, ispi->base + HSFSTS_CTL);
+
+		ret = intel_spi_wait_hw_busy(ispi);
+		if (ret)
+			return ret;
+
+		status = readl(ispi->base + HSFSTS_CTL);
+		if (status & HSFSTS_CTL_FCERR)
+			ret = -EIO;
+		else if (status & HSFSTS_CTL_AEL)
+			ret = -EACCES;
+
+		if (ret < 0) {
+			dev_err(ispi->dev, "read error: %llx: %#x\n", from,
+				status);
+			return ret;
+		}
+
+		ret = intel_spi_read_block(ispi, read_buf, block_size);
+		if (ret)
+			return ret;
+
+		len -= block_size;
+		from += block_size;
+		retlen += block_size;
+		read_buf += block_size;
+	}
+
+	return retlen;
+}
+
+static ssize_t intel_spi_write(struct spi_nor *nor, loff_t to, size_t len,
+			       const u_char *write_buf)
+{
+	struct intel_spi *ispi = nor->priv;
+	size_t block_size, retlen = 0;
+	u32 val, status;
+	ssize_t ret;
+
+	while (len > 0) {
+		block_size = min_t(size_t, len, INTEL_SPI_FIFO_SZ);
+
+		writel(to, ispi->base + FADDR);
+
+		val = readl(ispi->base + HSFSTS_CTL);
+		val &= ~(HSFSTS_CTL_FDBC_MASK | HSFSTS_CTL_FCYCLE_MASK);
+		val |= HSFSTS_CTL_AEL | HSFSTS_CTL_FCERR | HSFSTS_CTL_FDONE;
+		val |= (block_size - 1) << HSFSTS_CTL_FDBC_SHIFT;
+		val |= HSFSTS_CTL_FCYCLE_WRITE;
+
+		/* Write enable */
+		if (ispi->preopcodes[1] == SPINOR_OP_WREN)
+			val |= SSFSTS_CTL_SPOP;
+		val |= SSFSTS_CTL_ACS;
+		writel(val, ispi->base + HSFSTS_CTL);
+
+		ret = intel_spi_write_block(ispi, write_buf, block_size);
+		if (ret) {
+			dev_err(ispi->dev, "failed to write block\n");
+			return ret;
+		}
+
+		/* Start the write now */
+		val = readl(ispi->base + HSFSTS_CTL);
+		writel(val | HSFSTS_CTL_FGO, ispi->base + HSFSTS_CTL);
+
+		ret = intel_spi_wait_hw_busy(ispi);
+		if (ret) {
+			dev_err(ispi->dev, "timeout\n");
+			return ret;
+		}
+
+		status = readl(ispi->base + HSFSTS_CTL);
+		if (status & HSFSTS_CTL_FCERR)
+			ret = -EIO;
+		else if (status & HSFSTS_CTL_AEL)
+			ret = -EACCES;
+
+		if (ret < 0) {
+			dev_err(ispi->dev, "write error: %llx: %#x\n", to,
+				status);
+			return ret;
+		}
+
+		len -= block_size;
+		to += block_size;
+		retlen += block_size;
+		write_buf += block_size;
+	}
+
+	return retlen;
+}
+
+static int intel_spi_erase(struct spi_nor *nor, loff_t offs)
+{
+	size_t erase_size, len = nor->mtd.erasesize;
+	struct intel_spi *ispi = nor->priv;
+	u32 val, status, cmd;
+	int ret;
+
+	/* If the hardware can do 64k erase use that when possible */
+	if (len >= SZ_64K && ispi->erase_64k) {
+		cmd = HSFSTS_CTL_FCYCLE_ERASE_64K;
+		erase_size = SZ_64K;
+	} else {
+		cmd = HSFSTS_CTL_FCYCLE_ERASE;
+		erase_size = SZ_4K;
+	}
+
+	while (len > 0) {
+		writel(offs, ispi->base + FADDR);
+
+		val = readl(ispi->base + HSFSTS_CTL);
+		val &= ~(HSFSTS_CTL_FDBC_MASK | HSFSTS_CTL_FCYCLE_MASK);
+		val |= HSFSTS_CTL_AEL | HSFSTS_CTL_FCERR | HSFSTS_CTL_FDONE;
+		val |= cmd;
+		val |= HSFSTS_CTL_FGO;
+		writel(val, ispi->base + HSFSTS_CTL);
+
+		ret = intel_spi_wait_hw_busy(ispi);
+		if (ret)
+			return ret;
+
+		status = readl(ispi->base + HSFSTS_CTL);
+		if (status & HSFSTS_CTL_FCERR)
+			return -EIO;
+		else if (status & HSFSTS_CTL_AEL)
+			return -EACCES;
+
+		offs += erase_size;
+		len -= erase_size;
+	}
+
+	return 0;
+}
+
+static bool intel_spi_is_protected(const struct intel_spi *ispi,
+				   unsigned int base, unsigned int limit)
+{
+	int i;
+
+	for (i = 0; i < PR_NUM; i++) {
+		u32 pr_base, pr_limit, pr_value;
+
+		pr_value = readl(ispi->pregs + PR(i));
+		if (!(pr_value & (PR_WPE | PR_RPE)))
+			continue;
+
+		pr_limit = (pr_value & PR_LIMIT_MASK) >> PR_LIMIT_SHIFT;
+		pr_base = pr_value & PR_BASE_MASK;
+
+		if (pr_base >= base && pr_limit <= limit)
+			return true;
+	}
+
+	return false;
+}
+
+/*
+ * There will be a single partition holding all enabled flash regions. We
+ * call this "BIOS".
+ */
+static void intel_spi_fill_partition(struct intel_spi *ispi,
+				     struct mtd_partition *part)
+{
+	u64 end;
+	int i;
+
+	memset(part, 0, sizeof(*part));
+
+	/* Start from the mandatory descriptor region */
+	part->size = 4096;
+	part->name = "BIOS";
+
+	/*
+	 * Now try to find where this partition ends based on the flash
+	 * region registers.
+	 */
+	for (i = 1; i < ispi->nregions; i++) {
+		u32 region, base, limit;
+
+		region = readl(ispi->base + FREG(i));
+		base = region & FREG_BASE_MASK;
+		limit = (region & FREG_LIMIT_MASK) >> FREG_LIMIT_SHIFT;
+
+		if (base >= limit || limit == 0)
+			continue;
+
+		/*
+		 * If any of the regions have protection bits set, make the
+		 * whole partition read-only to be on the safe side.
+		 */
+		if (intel_spi_is_protected(ispi, base, limit))
+			ispi->writeable = 0;
+
+		end = (limit << 12) + 4096;
+		if (end > part->size)
+			part->size = end;
+	}
+}
+
+struct intel_spi *intel_spi_probe(struct device *dev,
+	struct resource *mem, const struct intel_spi_boardinfo *info)
+{
+	struct mtd_partition part;
+	struct intel_spi *ispi;
+	int ret;
+
+	if (!info || !mem)
+		return ERR_PTR(-EINVAL);
+
+	ispi = devm_kzalloc(dev, sizeof(*ispi), GFP_KERNEL);
+	if (!ispi)
+		return ERR_PTR(-ENOMEM);
+
+	ispi->base = devm_ioremap_resource(dev, mem);
+	if (IS_ERR(ispi->base))
+		return ispi->base;
+
+	ispi->dev = dev;
+	ispi->info = info;
+	ispi->writeable = info->writeable;
+
+	ret = intel_spi_init(ispi);
+	if (ret)
+		return ERR_PTR(ret);
+
+	ispi->nor.dev = ispi->dev;
+	ispi->nor.priv = ispi;
+	ispi->nor.read_reg = intel_spi_read_reg;
+	ispi->nor.write_reg = intel_spi_write_reg;
+	ispi->nor.read = intel_spi_read;
+	ispi->nor.write = intel_spi_write;
+	ispi->nor.erase = intel_spi_erase;
+
+	ret = spi_nor_scan(&ispi->nor, NULL, SPI_NOR_NORMAL);
+	if (ret) {
+		dev_info(dev, "failed to locate the chip\n");
+		return ERR_PTR(ret);
+	}
+
+	intel_spi_fill_partition(ispi, &part);
+
+	/* Prevent writes if not explicitly enabled */
+	if (!ispi->writeable || !writeable)
+		ispi->nor.mtd.flags &= ~MTD_WRITEABLE;
+
+	ret = mtd_device_parse_register(&ispi->nor.mtd, NULL, NULL, &part, 1);
+	if (ret)
+		return ERR_PTR(ret);
+
+	return ispi;
+}
+EXPORT_SYMBOL_GPL(intel_spi_probe);
+
+int intel_spi_remove(struct intel_spi *ispi)
+{
+	return mtd_device_unregister(&ispi->nor.mtd);
+}
+EXPORT_SYMBOL_GPL(intel_spi_remove);
+
+MODULE_DESCRIPTION("Intel PCH/PCU SPI flash core driver");
+MODULE_AUTHOR("Mika Westerberg <mika.westerberg@linux.intel.com>");
+MODULE_LICENSE("GPL v2");

drivers/mtd/spi-nor/intel-spi.h

+/*
+ * Intel PCH/PCU SPI flash driver.
+ *
+ * Copyright (C) 2016, Intel Corporation
+ * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef INTEL_SPI_H
+#define INTEL_SPI_H
+
+#include <linux/platform_data/intel-spi.h>
+
+struct intel_spi;
+struct resource;
+
+struct intel_spi *intel_spi_probe(struct device *dev,
+	struct resource *mem, const struct intel_spi_boardinfo *info);
+int intel_spi_remove(struct intel_spi *ispi);
+
+#endif /* INTEL_SPI_H */

drivers/power/supply/axp288_charger.c

@@ -143,7 +143,6 @@ enum {
 
 struct axp288_chrg_info {
 	struct platform_device *pdev;
-	struct axp20x_chrg_pdata *pdata;
 	struct regmap *regmap;
 	struct regmap_irq_chip_data *regmap_irqc;
 	int irq[CHRG_INTR_END];
@@ -701,110 +700,112 @@ static int axp288_charger_handle_otg_evt(struct notifier_block *nb,
 	return NOTIFY_OK;
 }
 
-static void charger_init_hw_regs(struct axp288_chrg_info *info)
+static int charger_init_hw_regs(struct axp288_chrg_info *info)
 {
 	int ret, cc, cv;
 	unsigned int val;
 
 	/* Program temperature thresholds */
 	ret = regmap_write(info->regmap, AXP20X_V_LTF_CHRG, CHRG_VLTFC_0C);
-	if (ret < 0)
-		dev_warn(&info->pdev->dev, "register(%x) write error(%d)\n",
+	if (ret < 0) {
+		dev_err(&info->pdev->dev, "register(%x) write error(%d)\n",
 							AXP20X_V_LTF_CHRG, ret);
+		return ret;
+	}
 
 	ret = regmap_write(info->regmap, AXP20X_V_HTF_CHRG, CHRG_VHTFC_45C);
-	if (ret < 0)
-		dev_warn(&info->pdev->dev, "register(%x) write error(%d)\n",
+	if (ret < 0) {
+		dev_err(&info->pdev->dev, "register(%x) write error(%d)\n",
 							AXP20X_V_HTF_CHRG, ret);
+		return ret;
+	}
 
 	/* Do not turn-off charger o/p after charge cycle ends */
 	ret = regmap_update_bits(info->regmap,
 				AXP20X_CHRG_CTRL2,
 				CNTL2_CHG_OUT_TURNON, 1);
-	if (ret < 0)
-		dev_warn(&info->pdev->dev, "register(%x) write error(%d)\n",
+	if (ret < 0) {
+		dev_err(&info->pdev->dev, "register(%x) write error(%d)\n",
 						AXP20X_CHRG_CTRL2, ret);
+		return ret;
+	}
 
 	/* Enable interrupts */
 	ret = regmap_update_bits(info->regmap,
 				AXP20X_IRQ2_EN,
 				BAT_IRQ_CFG_BAT_MASK, 1);
-	if (ret < 0)
-		dev_warn(&info->pdev->dev, "register(%x) write error(%d)\n",
+	if (ret < 0) {
+		dev_err(&info->pdev->dev, "register(%x) write error(%d)\n",
 						AXP20X_IRQ2_EN, ret);
+		return ret;
+	}
 
 	ret = regmap_update_bits(info->regmap, AXP20X_IRQ3_EN,
 				TEMP_IRQ_CFG_MASK, 1);
-	if (ret < 0)
-		dev_warn(&info->pdev->dev, "register(%x) write error(%d)\n",
+	if (ret < 0) {
+		dev_err(&info->pdev->dev, "register(%x) write error(%d)\n",
 						AXP20X_IRQ3_EN, ret);
+		return ret;
+	}
 
 	/* Setup ending condition for charging to be 10% of I(chrg) */
 	ret = regmap_update_bits(info->regmap,
 				AXP20X_CHRG_CTRL1,
 				CHRG_CCCV_ITERM_20P, 0);
-	if (ret < 0)
-		dev_warn(&info->pdev->dev, "register(%x) write error(%d)\n",
+	if (ret < 0) {
+		dev_err(&info->pdev->dev, "register(%x) write error(%d)\n",
 						AXP20X_CHRG_CTRL1, ret);
+		return ret;
+	}
 
 	/* Disable OCV-SOC curve calibration */
 	ret = regmap_update_bits(info->regmap,
 				AXP20X_CC_CTRL,
 				FG_CNTL_OCV_ADJ_EN, 0);
-	if (ret < 0)
-		dev_warn(&info->pdev->dev, "register(%x) write error(%d)\n",
+	if (ret < 0) {
+		dev_err(&info->pdev->dev, "register(%x) write error(%d)\n",
 						AXP20X_CC_CTRL, ret);
-
-	/* Init charging current and voltage */
-	info->max_cc = info->pdata->max_cc;
-	info->max_cv = info->pdata->max_cv;
+		return ret;
+	}
 
 	/* Read current charge voltage and current limit */
 	ret = regmap_read(info->regmap, AXP20X_CHRG_CTRL1, &val);
 	if (ret < 0) {
-		/* Assume default if cannot read */
-		info->cc = info->pdata->def_cc;
-		info->cv = info->pdata->def_cv;
-	} else {
-		/* Determine charge voltage */
-		cv = (val & CHRG_CCCV_CV_MASK) >> CHRG_CCCV_CV_BIT_POS;
-		switch (cv) {
-		case CHRG_CCCV_CV_4100MV:
-			info->cv = CV_4100MV;
-			break;
-		case CHRG_CCCV_CV_4150MV:
-			info->cv = CV_4150MV;
-			break;
-		case CHRG_CCCV_CV_4200MV:
-			info->cv = CV_4200MV;
-			break;
-		case CHRG_CCCV_CV_4350MV:
-			info->cv = CV_4350MV;
-			break;
-		default:
-			info->cv = INT_MAX;
-			break;
-		}
+		dev_err(&info->pdev->dev, "register(%x) read error(%d)\n",
+			AXP20X_CHRG_CTRL1, ret);
+		return ret;
+	}
 
-		/* Determine charge current limit */
-		cc = (ret & CHRG_CCCV_CC_MASK) >> CHRG_CCCV_CC_BIT_POS;
-		cc = (cc * CHRG_CCCV_CC_LSB_RES) + CHRG_CCCV_CC_OFFSET;
-		info->cc = cc;
+	/* Determine charge voltage */
+	cv = (val & CHRG_CCCV_CV_MASK) >> CHRG_CCCV_CV_BIT_POS;
+	switch (cv) {
+	case CHRG_CCCV_CV_4100MV:
+		info->cv = CV_4100MV;
+		break;
+	case CHRG_CCCV_CV_4150MV:
+		info->cv = CV_4150MV;
+		break;
+	case CHRG_CCCV_CV_4200MV:
+		info->cv = CV_4200MV;
+		break;
+	case CHRG_CCCV_CV_4350MV:
+		info->cv = CV_4350MV;
+		break;
+	}
 
-		/* Program default charging voltage and current */
-		cc = min(info->pdata->def_cc, info->max_cc);
-		cv = min(info->pdata->def_cv, info->max_cv);
+	/* Determine charge current limit */
+	cc = (ret & CHRG_CCCV_CC_MASK) >> CHRG_CCCV_CC_BIT_POS;
+	cc = (cc * CHRG_CCCV_CC_LSB_RES) + CHRG_CCCV_CC_OFFSET;
+	info->cc = cc;
 
-		ret = axp288_charger_set_cc(info, cc);
-		if (ret < 0)
-			dev_warn(&info->pdev->dev,
-					"error(%d) in setting CC\n", ret);
+	/*
+	 * Do not allow the user to configure higher settings then those
+	 * set by the firmware
+	 */
+	info->max_cv = info->cv;
+	info->max_cc = info->cc;
 
-		ret = axp288_charger_set_cv(info, cv);
-		if (ret < 0)
-			dev_warn(&info->pdev->dev,
-					"error(%d) in setting CV\n", ret);
-	}
+	return 0;
 }
 
 static int axp288_charger_probe(struct platform_device *pdev)
@@ -821,15 +822,6 @@ static int axp288_charger_probe(struct platform_device *pdev)
 	info->pdev = pdev;
 	info->regmap = axp20x->regmap;
 	info->regmap_irqc = axp20x->regmap_irqc;
-	info->pdata = pdev->dev.platform_data;
-
-	if (!info->pdata) {
-		/* Try ACPI provided pdata via device properties */
-		if (!device_property_present(&pdev->dev,
-						"axp288_charger_data\n"))
-			dev_err(&pdev->dev, "failed to get platform data\n");
-		return -ENODEV;
-	}
 
 	info->cable.edev = extcon_get_extcon_dev(AXP288_EXTCON_DEV_NAME);
 	if (info->cable.edev == NULL) {
@@ -916,7 +908,9 @@ static int axp288_charger_probe(struct platform_device *pdev)
 		}
 	}
 
-	charger_init_hw_regs(info);
+	ret = charger_init_hw_regs(info);
+	if (ret)
+		goto intr_reg_failed;
 
 	return 0;
 

drivers/power/supply/axp288_fuel_gauge.c

@@ -49,11 +49,6 @@
 #define CHRG_CCCV_CV_4350MV			0x3     /* 4.35V */
 #define CHRG_CCCV_CHG_EN			(1 << 7)
 
-#define CV_4100						4100    /* 4100mV */
-#define CV_4150						4150    /* 4150mV */
-#define CV_4200						4200    /* 4200mV */
-#define CV_4350						4350    /* 4350mV */
-
 #define TEMP_IRQ_CFG_QWBTU			(1 << 0)
 #define TEMP_IRQ_CFG_WBTU			(1 << 1)
 #define TEMP_IRQ_CFG_QWBTO			(1 << 2)
@@ -104,9 +99,7 @@
 
 /* 1.1mV per LSB expressed in uV */
 #define VOLTAGE_FROM_ADC(a)			((a * 11) / 10)
-/* properties converted to tenths of degrees, uV, uA, uW */
-#define PROP_TEMP(a)		((a) * 10)
-#define UNPROP_TEMP(a)		((a) / 10)
+/* properties converted to uV, uA */
 #define PROP_VOLT(a)		((a) * 1000)
 #define PROP_CURR(a)		((a) * 1000)
 
@@ -122,13 +115,13 @@ enum {
 
 struct axp288_fg_info {
 	struct platform_device *pdev;
-	struct axp20x_fg_pdata *pdata;
 	struct regmap *regmap;
 	struct regmap_irq_chip_data *regmap_irqc;
 	int irq[AXP288_FG_INTR_NUM];
 	struct power_supply *bat;
 	struct mutex lock;
 	int status;
+	int max_volt;
 	struct delayed_work status_monitor;
 	struct dentry *debug_file;
 };
@@ -138,22 +131,14 @@ static enum power_supply_property fuel_gauge_props[] = {
 	POWER_SUPPLY_PROP_PRESENT,
 	POWER_SUPPLY_PROP_HEALTH,
 	POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
-	POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
 	POWER_SUPPLY_PROP_VOLTAGE_NOW,
 	POWER_SUPPLY_PROP_VOLTAGE_OCV,
 	POWER_SUPPLY_PROP_CURRENT_NOW,
 	POWER_SUPPLY_PROP_CAPACITY,
 	POWER_SUPPLY_PROP_CAPACITY_ALERT_MIN,
-	POWER_SUPPLY_PROP_TEMP,
-	POWER_SUPPLY_PROP_TEMP_MAX,
-	POWER_SUPPLY_PROP_TEMP_MIN,
-	POWER_SUPPLY_PROP_TEMP_ALERT_MIN,
-	POWER_SUPPLY_PROP_TEMP_ALERT_MAX,
 	POWER_SUPPLY_PROP_TECHNOLOGY,
 	POWER_SUPPLY_PROP_CHARGE_FULL,
 	POWER_SUPPLY_PROP_CHARGE_NOW,
-	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
-	POWER_SUPPLY_PROP_MODEL_NAME,
 };
 
 static int fuel_gauge_reg_readb(struct axp288_fg_info *info, int reg)
@@ -417,102 +402,6 @@ static int fuel_gauge_get_current(struct axp288_fg_info *info, int *cur)
 	return ret;
 }
 
-static int temp_to_adc(struct axp288_fg_info *info, int tval)
-{
-	int rntc = 0, i, ret, adc_val;
-	int rmin, rmax, tmin, tmax;
-	int tcsz = info->pdata->tcsz;
-
-	/* get the Rntc resitance value for this temp */
-	if (tval > info->pdata->thermistor_curve[0][1]) {
-		rntc = info->pdata->thermistor_curve[0][0];
-	} else if (tval <= info->pdata->thermistor_curve[tcsz-1][1]) {
-		rntc = info->pdata->thermistor_curve[tcsz-1][0];
-	} else {
-		for (i = 1; i < tcsz; i++) {
-			if (tval > info->pdata->thermistor_curve[i][1]) {
-				rmin = info->pdata->thermistor_curve[i-1][0];
-				rmax = info->pdata->thermistor_curve[i][0];
-				tmin = info->pdata->thermistor_curve[i-1][1];
-				tmax = info->pdata->thermistor_curve[i][1];
-				rntc = rmin + ((rmax - rmin) *
-					(tval - tmin) / (tmax - tmin));
-				break;
-			}
-		}
-	}
-
-	/* we need the current to calculate the proper adc voltage */
-	ret = fuel_gauge_reg_readb(info, AXP20X_ADC_RATE);
-	if (ret < 0) {
-		dev_err(&info->pdev->dev, "%s:read err:%d\n", __func__, ret);
-		ret = 0x30;
-	}
-
-	/*
-	 * temperature is proportional to NTS thermistor resistance
-	 * ADC_RATE[5-4] determines current, 00=20uA,01=40uA,10=60uA,11=80uA
-	 * [12-bit ADC VAL] = R_NTC(Ω) * current / 800
-	 */
-	adc_val = rntc * (20 + (20 * ((ret >> 4) & 0x3))) / 800;
-
-	return adc_val;
-}
-
-static int adc_to_temp(struct axp288_fg_info *info, int adc_val)
-{
-	int ret, r, i, tval = 0;
-	int rmin, rmax, tmin, tmax;
-	int tcsz = info->pdata->tcsz;
-
-	ret = fuel_gauge_reg_readb(info, AXP20X_ADC_RATE);
-	if (ret < 0) {
-		dev_err(&info->pdev->dev, "%s:read err:%d\n", __func__, ret);
-		ret = 0x30;
-	}
-
-	/*
-	 * temperature is proportional to NTS thermistor resistance
-	 * ADC_RATE[5-4] determines current, 00=20uA,01=40uA,10=60uA,11=80uA
-	 * R_NTC(Ω) = [12-bit ADC VAL] * 800 / current
-	 */
-	r = adc_val * 800 / (20 + (20 * ((ret >> 4) & 0x3)));
-
-	if (r < info->pdata->thermistor_curve[0][0]) {
-		tval = info->pdata->thermistor_curve[0][1];
-	} else if (r >= info->pdata->thermistor_curve[tcsz-1][0]) {
-		tval = info->pdata->thermistor_curve[tcsz-1][1];
-	} else {
-		for (i = 1; i < tcsz; i++) {
-			if (r < info->pdata->thermistor_curve[i][0]) {
-				rmin = info->pdata->thermistor_curve[i-1][0];
-				rmax = info->pdata->thermistor_curve[i][0];
-				tmin = info->pdata->thermistor_curve[i-1][1];
-				tmax = info->pdata->thermistor_curve[i][1];
-				tval = tmin + ((tmax - tmin) *
-					(r - rmin) / (rmax - rmin));
-				break;
-			}
-		}
-	}
-
-	return tval;
-}
-
-static int fuel_gauge_get_btemp(struct axp288_fg_info *info, int *btemp)
-{
-	int ret, raw_val = 0;
-
-	ret = pmic_read_adc_val("axp288-batt-temp", &raw_val, info);
-	if (ret < 0)
-		goto temp_read_fail;
-
-	*btemp = adc_to_temp(info, raw_val);
-
-temp_read_fail:
-	return ret;
-}
-
 static int fuel_gauge_get_vocv(struct axp288_fg_info *info, int *vocv)
 {
 	int ret, value;
@@ -535,25 +424,14 @@ static int fuel_gauge_get_vocv(struct axp288_fg_info *info, int *vocv)
 
 static int fuel_gauge_battery_health(struct axp288_fg_info *info)
 {
-	int temp, vocv;
-	int ret, health = POWER_SUPPLY_HEALTH_UNKNOWN;
-
-	ret = fuel_gauge_get_btemp(info, &temp);
-	if (ret < 0)
-		goto health_read_fail;
+	int ret, vocv, health = POWER_SUPPLY_HEALTH_UNKNOWN;
 
 	ret = fuel_gauge_get_vocv(info, &vocv);
 	if (ret < 0)
 		goto health_read_fail;
 
-	if (vocv > info->pdata->max_volt)
+	if (vocv > info->max_volt)
 		health = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
-	else if (temp > info->pdata->max_temp)
-		health = POWER_SUPPLY_HEALTH_OVERHEAT;
-	else if (temp < info->pdata->min_temp)
-		health = POWER_SUPPLY_HEALTH_COLD;
-	else if (vocv < info->pdata->min_volt)
-		health = POWER_SUPPLY_HEALTH_DEAD;
 	else
 		health = POWER_SUPPLY_HEALTH_GOOD;
 
@@ -561,28 +439,6 @@ static int fuel_gauge_battery_health(struct axp288_fg_info *info)
 	return health;
 }
 
-static int fuel_gauge_set_high_btemp_alert(struct axp288_fg_info *info)
-{
-	int ret, adc_val;
-
-	/* program temperature threshold as 1/16 ADC value */
-	adc_val = temp_to_adc(info, info->pdata->max_temp);
-	ret = fuel_gauge_reg_writeb(info, AXP20X_V_HTF_DISCHRG, adc_val >> 4);
-
-	return ret;
-}
-
-static int fuel_gauge_set_low_btemp_alert(struct axp288_fg_info *info)
-{
-	int ret, adc_val;
-
-	/* program temperature threshold as 1/16 ADC value */
-	adc_val = temp_to_adc(info, info->pdata->min_temp);
-	ret = fuel_gauge_reg_writeb(info, AXP20X_V_LTF_DISCHRG, adc_val >> 4);
-
-	return ret;
-}
-
 static int fuel_gauge_get_property(struct power_supply *ps,
 		enum power_supply_property prop,
 		union power_supply_propval *val)
@@ -643,20 +499,6 @@ static int fuel_gauge_get_property(struct power_supply *ps,
 			goto fuel_gauge_read_err;
 		val->intval = (ret & 0x0f);
 		break;
-	case POWER_SUPPLY_PROP_TEMP:
-		ret = fuel_gauge_get_btemp(info, &value);
-		if (ret < 0)
-			goto fuel_gauge_read_err;
-		val->intval = PROP_TEMP(value);
-		break;
-	case POWER_SUPPLY_PROP_TEMP_MAX:
-	case POWER_SUPPLY_PROP_TEMP_ALERT_MAX:
-		val->intval = PROP_TEMP(info->pdata->max_temp);
-		break;
-	case POWER_SUPPLY_PROP_TEMP_MIN:
-	case POWER_SUPPLY_PROP_TEMP_ALERT_MIN:
-		val->intval = PROP_TEMP(info->pdata->min_temp);
-		break;
 	case POWER_SUPPLY_PROP_TECHNOLOGY:
 		val->intval = POWER_SUPPLY_TECHNOLOGY_LION;
 		break;
@@ -684,17 +526,8 @@ static int fuel_gauge_get_property(struct power_supply *ps,
 		value |= (ret & FG_DES_CAP0_VAL_MASK);
 		val->intval = value * FG_DES_CAP_RES_LSB;
 		break;
-	case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN:
-		val->intval = PROP_CURR(info->pdata->design_cap);
-		break;
 	case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
-		val->intval = PROP_VOLT(info->pdata->max_volt);
-		break;
-	case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
-		val->intval = PROP_VOLT(info->pdata->min_volt);
-		break;
-	case POWER_SUPPLY_PROP_MODEL_NAME:
-		val->strval = info->pdata->battid;
+		val->intval = PROP_VOLT(info->max_volt);
 		break;
 	default:
 		mutex_unlock(&info->lock);
@@ -718,35 +551,6 @@ static int fuel_gauge_set_property(struct power_supply *ps,
 
 	mutex_lock(&info->lock);
 	switch (prop) {
-	case POWER_SUPPLY_PROP_STATUS:
-		info->status = val->intval;
-		break;
-	case POWER_SUPPLY_PROP_TEMP_MIN:
-	case POWER_SUPPLY_PROP_TEMP_ALERT_MIN:
-		if ((val->intval < PD_DEF_MIN_TEMP) ||
-			(val->intval > PD_DEF_MAX_TEMP)) {
-			ret = -EINVAL;
-			break;
-		}
-		info->pdata->min_temp = UNPROP_TEMP(val->intval);
-		ret = fuel_gauge_set_low_btemp_alert(info);
-		if (ret < 0)
-			dev_err(&info->pdev->dev,
-				"temp alert min set fail:%d\n", ret);
-		break;
-	case POWER_SUPPLY_PROP_TEMP_MAX:
-	case POWER_SUPPLY_PROP_TEMP_ALERT_MAX:
-		if ((val->intval < PD_DEF_MIN_TEMP) ||
-			(val->intval > PD_DEF_MAX_TEMP)) {
-			ret = -EINVAL;
-			break;
-		}
-		info->pdata->max_temp = UNPROP_TEMP(val->intval);
-		ret = fuel_gauge_set_high_btemp_alert(info);
-		if (ret < 0)
-			dev_err(&info->pdev->dev,
-				"temp alert max set fail:%d\n", ret);
-		break;
 	case POWER_SUPPLY_PROP_CAPACITY_ALERT_MIN:
 		if ((val->intval < 0) || (val->intval > 15)) {
 			ret = -EINVAL;
@@ -774,11 +578,6 @@ static int fuel_gauge_property_is_writeable(struct power_supply *psy,
 	int ret;
 
 	switch (psp) {
-	case POWER_SUPPLY_PROP_STATUS:
-	case POWER_SUPPLY_PROP_TEMP_MIN:
-	case POWER_SUPPLY_PROP_TEMP_ALERT_MIN:
-	case POWER_SUPPLY_PROP_TEMP_MAX:
-	case POWER_SUPPLY_PROP_TEMP_ALERT_MAX:
 	case POWER_SUPPLY_PROP_CAPACITY_ALERT_MIN:
 		ret = 1;
 		break;
@@ -863,158 +662,6 @@ static const struct power_supply_desc fuel_gauge_desc = {
 	.external_power_changed	= fuel_gauge_external_power_changed,
 };
 
-static int fuel_gauge_set_lowbatt_thresholds(struct axp288_fg_info *info)
-{
-	int ret;
-	u8 reg_val;
-
-	ret = fuel_gauge_reg_readb(info, AXP20X_FG_RES);
-	if (ret < 0) {
-		dev_err(&info->pdev->dev, "%s:read err:%d\n", __func__, ret);
-		return ret;
-	}
-	ret = (ret & FG_REP_CAP_VAL_MASK);
-
-	if (ret > FG_LOW_CAP_WARN_THR)
-		reg_val = FG_LOW_CAP_WARN_THR;
-	else if (ret > FG_LOW_CAP_CRIT_THR)
-		reg_val = FG_LOW_CAP_CRIT_THR;
-	else
-		reg_val = FG_LOW_CAP_SHDN_THR;
-
-	reg_val |= FG_LOW_CAP_THR1_VAL;
-	ret = fuel_gauge_reg_writeb(info, AXP288_FG_LOW_CAP_REG, reg_val);
-	if (ret < 0)
-		dev_err(&info->pdev->dev, "%s:write err:%d\n", __func__, ret);
-
-	return ret;
-}
-
-static int fuel_gauge_program_vbatt_full(struct axp288_fg_info *info)
-{
-	int ret;
-	u8 val;
-
-	ret = fuel_gauge_reg_readb(info, AXP20X_CHRG_CTRL1);
-	if (ret < 0)
-		goto fg_prog_ocv_fail;
-	else
-		val = (ret & ~CHRG_CCCV_CV_MASK);
-
-	switch (info->pdata->max_volt) {
-	case CV_4100:
-		val |= (CHRG_CCCV_CV_4100MV << CHRG_CCCV_CV_BIT_POS);
-		break;
-	case CV_4150:
-		val |= (CHRG_CCCV_CV_4150MV << CHRG_CCCV_CV_BIT_POS);
-		break;
-	case CV_4200:
-		val |= (CHRG_CCCV_CV_4200MV << CHRG_CCCV_CV_BIT_POS);
-		break;
-	case CV_4350:
-		val |= (CHRG_CCCV_CV_4350MV << CHRG_CCCV_CV_BIT_POS);
-		break;
-	default:
-		val |= (CHRG_CCCV_CV_4200MV << CHRG_CCCV_CV_BIT_POS);
-		break;
-	}
-
-	ret = fuel_gauge_reg_writeb(info, AXP20X_CHRG_CTRL1, val);
-fg_prog_ocv_fail:
-	return ret;
-}
-
-static int fuel_gauge_program_design_cap(struct axp288_fg_info *info)
-{
-	int ret;
-
-	ret = fuel_gauge_reg_writeb(info,
-		AXP288_FG_DES_CAP1_REG, info->pdata->cap1);
-	if (ret < 0)
-		goto fg_prog_descap_fail;
-
-	ret = fuel_gauge_reg_writeb(info,
-		AXP288_FG_DES_CAP0_REG, info->pdata->cap0);
-
-fg_prog_descap_fail:
-	return ret;
-}
-
-static int fuel_gauge_program_ocv_curve(struct axp288_fg_info *info)
-{
-	int ret = 0, i;
-
-	for (i = 0; i < OCV_CURVE_SIZE; i++) {
-		ret = fuel_gauge_reg_writeb(info,
-			AXP288_FG_OCV_CURVE_REG + i, info->pdata->ocv_curve[i]);
-		if (ret < 0)
-			goto fg_prog_ocv_fail;
-	}
-
-fg_prog_ocv_fail:
-	return ret;
-}
-
-static int fuel_gauge_program_rdc_vals(struct axp288_fg_info *info)
-{
-	int ret;
-
-	ret = fuel_gauge_reg_writeb(info,
-		AXP288_FG_RDC1_REG, info->pdata->rdc1);
-	if (ret < 0)
-		goto fg_prog_ocv_fail;
-
-	ret = fuel_gauge_reg_writeb(info,
-		AXP288_FG_RDC0_REG, info->pdata->rdc0);
-
-fg_prog_ocv_fail:
-	return ret;
-}
-
-static void fuel_gauge_init_config_regs(struct axp288_fg_info *info)
-{
-	int ret;
-
-	/*
-	 * check if the config data is already
-	 * programmed and if so just return.
-	 */
-
-	ret = fuel_gauge_reg_readb(info, AXP288_FG_DES_CAP1_REG);
-	if (ret < 0) {
-		dev_warn(&info->pdev->dev, "CAP1 reg read err!!\n");
-	} else if (!(ret & FG_DES_CAP1_VALID)) {
-		dev_info(&info->pdev->dev, "FG data needs to be initialized\n");
-	} else {
-		dev_info(&info->pdev->dev, "FG data is already initialized\n");
-		return;
-	}
-
-	ret = fuel_gauge_program_vbatt_full(info);
-	if (ret < 0)
-		dev_err(&info->pdev->dev, "set vbatt full fail:%d\n", ret);
-
-	ret = fuel_gauge_program_design_cap(info);
-	if (ret < 0)
-		dev_err(&info->pdev->dev, "set design cap fail:%d\n", ret);
-
-	ret = fuel_gauge_program_rdc_vals(info);
-	if (ret < 0)
-		dev_err(&info->pdev->dev, "set rdc fail:%d\n", ret);
-
-	ret = fuel_gauge_program_ocv_curve(info);
-	if (ret < 0)
-		dev_err(&info->pdev->dev, "set ocv curve fail:%d\n", ret);
-
-	ret = fuel_gauge_set_lowbatt_thresholds(info);
-	if (ret < 0)
-		dev_err(&info->pdev->dev, "lowbatt thr set fail:%d\n", ret);
-
-	ret = fuel_gauge_reg_writeb(info, AXP20X_CC_CTRL, 0xef);
-	if (ret < 0)
-		dev_err(&info->pdev->dev, "gauge cntl set fail:%d\n", ret);
-}
-
 static void fuel_gauge_init_irq(struct axp288_fg_info *info)
 {
 	int ret, i, pirq;
@@ -1054,17 +701,8 @@ static void fuel_gauge_init_irq(struct axp288_fg_info *info)
 
 static void fuel_gauge_init_hw_regs(struct axp288_fg_info *info)
 {
-	int ret;
 	unsigned int val;
 
-	ret = fuel_gauge_set_high_btemp_alert(info);
-	if (ret < 0)
-		dev_err(&info->pdev->dev, "high batt temp set fail:%d\n", ret);
-
-	ret = fuel_gauge_set_low_btemp_alert(info);
-	if (ret < 0)
-		dev_err(&info->pdev->dev, "low batt temp set fail:%d\n", ret);
-
 	/* enable interrupts */
 	val = fuel_gauge_reg_readb(info, AXP20X_IRQ3_EN);
 	val |= TEMP_IRQ_CFG_MASK;
@@ -1090,15 +728,39 @@ static int axp288_fuel_gauge_probe(struct platform_device *pdev)
 	info->regmap = axp20x->regmap;
 	info->regmap_irqc = axp20x->regmap_irqc;
 	info->status = POWER_SUPPLY_STATUS_UNKNOWN;
-	info->pdata = pdev->dev.platform_data;
-	if (!info->pdata)
-		return -ENODEV;
 
 	platform_set_drvdata(pdev, info);
 
 	mutex_init(&info->lock);
 	INIT_DELAYED_WORK(&info->status_monitor, fuel_gauge_status_monitor);
 
+	ret = fuel_gauge_reg_readb(info, AXP288_FG_DES_CAP1_REG);
+	if (ret < 0)
+		return ret;
+
+	if (!(ret & FG_DES_CAP1_VALID)) {
+		dev_err(&pdev->dev, "axp288 not configured by firmware\n");
+		return -ENODEV;
+	}
+
+	ret = fuel_gauge_reg_readb(info, AXP20X_CHRG_CTRL1);
+	if (ret < 0)
+		return ret;
+	switch ((ret & CHRG_CCCV_CV_MASK) >> CHRG_CCCV_CV_BIT_POS) {
+	case CHRG_CCCV_CV_4100MV:
+		info->max_volt = 4100;
+		break;
+	case CHRG_CCCV_CV_4150MV:
+		info->max_volt = 4150;
+		break;
+	case CHRG_CCCV_CV_4200MV:
+		info->max_volt = 4200;
+		break;
+	case CHRG_CCCV_CV_4350MV:
+		info->max_volt = 4350;
+		break;
+	}
+
 	psy_cfg.drv_data = info;
 	info->bat = power_supply_register(&pdev->dev, &fuel_gauge_desc, &psy_cfg);
 	if (IS_ERR(info->bat)) {
@@ -1108,12 +770,11 @@ static int axp288_fuel_gauge_probe(struct platform_device *pdev)
 	}
 
 	fuel_gauge_create_debugfs(info);
-	fuel_gauge_init_config_regs(info);
 	fuel_gauge_init_irq(info);
 	fuel_gauge_init_hw_regs(info);
 	schedule_delayed_work(&info->status_monitor, STATUS_MON_DELAY_JIFFIES);
 
-	return ret;
+	return 0;
 }
 
 static const struct platform_device_id axp288_fg_id_table[] = {

include/linux/mfd/axp20x.h

@@ -532,35 +532,6 @@ struct axp20x_dev {
 	const struct regmap_irq_chip	*regmap_irq_chip;
 };
 
-#define BATTID_LEN				64
-#define OCV_CURVE_SIZE			32
-#define MAX_THERM_CURVE_SIZE	25
-#define PD_DEF_MIN_TEMP			0
-#define PD_DEF_MAX_TEMP			55
-
-struct axp20x_fg_pdata {
-	char battid[BATTID_LEN + 1];
-	int design_cap;
-	int min_volt;
-	int max_volt;
-	int max_temp;
-	int min_temp;
-	int cap1;
-	int cap0;
-	int rdc1;
-	int rdc0;
-	int ocv_curve[OCV_CURVE_SIZE];
-	int tcsz;
-	int thermistor_curve[MAX_THERM_CURVE_SIZE][2];
-};
-
-struct axp20x_chrg_pdata {
-	int max_cc;
-	int max_cv;
-	int def_cc;
-	int def_cv;
-};
-
 struct axp288_extcon_pdata {
 	/* GPIO pin control to switch D+/D- lines b/w PMIC and SOC */
 	struct gpio_desc *gpio_mux_cntl;

include/linux/mfd/cros_ec_commands.h

@@ -1839,18 +1839,69 @@ struct ec_response_tmp006_get_raw {
  *
  * Returns raw data for keyboard cols; see ec_response_mkbp_info.cols for
  * expected response size.
+ *
+ * NOTE: This has been superseded by EC_CMD_MKBP_GET_NEXT_EVENT.  If you wish
+ * to obtain the instantaneous state, use EC_CMD_MKBP_INFO with the type
+ * EC_MKBP_INFO_CURRENT and event EC_MKBP_EVENT_KEY_MATRIX.
  */
 #define EC_CMD_MKBP_STATE 0x60
 
-/* Provide information about the matrix : number of rows and columns */
+/*
+ * Provide information about various MKBP things.  See enum ec_mkbp_info_type.
+ */
 #define EC_CMD_MKBP_INFO 0x61
 
 struct ec_response_mkbp_info {
 	uint32_t rows;
 	uint32_t cols;
-	uint8_t switches;
+	/* Formerly "switches", which was 0. */
+	uint8_t reserved;
 } __packed;
 
+struct ec_params_mkbp_info {
+	uint8_t info_type;
+	uint8_t event_type;
+} __packed;
+
+enum ec_mkbp_info_type {
+	/*
+	 * Info about the keyboard matrix: number of rows and columns.
+	 *
+	 * Returns struct ec_response_mkbp_info.
+	 */
+	EC_MKBP_INFO_KBD = 0,
+
+	/*
+	 * For buttons and switches, info about which specifically are
+	 * supported.  event_type must be set to one of the values in enum
+	 * ec_mkbp_event.
+	 *
+	 * For EC_MKBP_EVENT_BUTTON and EC_MKBP_EVENT_SWITCH, returns a 4 byte
+	 * bitmask indicating which buttons or switches are present.  See the
+	 * bit inidices below.
+	 */
+	EC_MKBP_INFO_SUPPORTED = 1,
+
+	/*
+	 * Instantaneous state of buttons and switches.
+	 *
+	 * event_type must be set to one of the values in enum ec_mkbp_event.
+	 *
+	 * For EC_MKBP_EVENT_KEY_MATRIX, returns uint8_t key_matrix[13]
+	 * indicating the current state of the keyboard matrix.
+	 *
+	 * For EC_MKBP_EVENT_HOST_EVENT, return uint32_t host_event, the raw
+	 * event state.
+	 *
+	 * For EC_MKBP_EVENT_BUTTON, returns uint32_t buttons, indicating the
+	 * state of supported buttons.
+	 *
+	 * For EC_MKBP_EVENT_SWITCH, returns uint32_t switches, indicating the
+	 * state of supported switches.
+	 */
+	EC_MKBP_INFO_CURRENT = 2,
+};
+
 /* Simulate key press */
 #define EC_CMD_MKBP_SIMULATE_KEY 0x62
 
@@ -1983,6 +2034,12 @@ enum ec_mkbp_event {
 	/* New Sensor FIFO data. The event data is fifo_info structure. */
 	EC_MKBP_EVENT_SENSOR_FIFO = 2,
 
+	/* The state of the non-matrixed buttons have changed. */
+	EC_MKBP_EVENT_BUTTON = 3,
+
+	/* The state of the switches have changed. */
+	EC_MKBP_EVENT_SWITCH = 4,
+
 	/* Number of MKBP events */
 	EC_MKBP_EVENT_COUNT,
 };
@@ -1992,6 +2049,9 @@ union ec_response_get_next_data {
 
 	/* Unaligned */
 	uint32_t  host_event;
+
+	uint32_t   buttons;
+	uint32_t   switches;
 } __packed;
 
 struct ec_response_get_next_event {
@@ -2000,6 +2060,16 @@ struct ec_response_get_next_event {
 	union ec_response_get_next_data data;
 } __packed;
 
+/* Bit indices for buttons and switches.*/
+/* Buttons */
+#define EC_MKBP_POWER_BUTTON	0
+#define EC_MKBP_VOL_UP		1
+#define EC_MKBP_VOL_DOWN	2
+
+/* Switches */
+#define EC_MKBP_LID_OPEN	0
+#define EC_MKBP_TABLET_MODE	1
+
 /*****************************************************************************/
 /* Temperature sensor commands */
 

include/linux/mfd/lpc_ich.h

@@ -20,6 +20,8 @@
 #ifndef LPC_ICH_H
 #define LPC_ICH_H
 
+#include <linux/platform_data/intel-spi.h>
+
 /* GPIO resources */
 #define ICH_RES_GPIO	0
 #define ICH_RES_GPE0	1
@@ -40,6 +42,7 @@ struct lpc_ich_info {
 	char name[32];
 	unsigned int iTCO_version;
 	unsigned int gpio_version;
+	enum intel_spi_type spi_type;
 	u8 use_gpio;
 };
 

include/linux/platform_data/intel-spi.h

+/*
+ * Intel PCH/PCU SPI flash driver.
+ *
+ * Copyright (C) 2016, Intel Corporation
+ * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef INTEL_SPI_PDATA_H
+#define INTEL_SPI_PDATA_H
+
+enum intel_spi_type {
+	INTEL_SPI_BYT = 1,
+	INTEL_SPI_LPT,
+	INTEL_SPI_BXT,
+};
+
+/**
+ * struct intel_spi_boardinfo - Board specific data for Intel SPI driver
+ * @type: Type which this controller is compatible with
+ * @writeable: The chip is writeable
+ */
+struct intel_spi_boardinfo {
+	enum intel_spi_type type;
+	bool writeable;
+};
+
+#endif /* INTEL_SPI_PDATA_H */