IXP4xx: support for Goramo MultiLink router platform.

Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>

arch/arm/mach-ixp4xx/Kconfig

@@ -78,6 +78,12 @@ config MACH_IXDP465
 	  IXDP465 Development Platform (Also known as BMP).
 	  For more information on this platform, see <file:Documentation/arm/IXP4xx>.
 
+config MACH_GORAMO_MLR
+	bool "GORAMO Multi Link Router"
+	help
+	  Say 'Y' here if you want your kernel to support GORAMO
+	  MultiLink router.
+
 config MACH_KIXRP435
 	bool "KIXRP435"
 	help

arch/arm/mach-ixp4xx/Makefile

@@ -30,6 +30,7 @@ obj-$(CONFIG_MACH_DSMG600)      += dsmg600-setup.o
 obj-$(CONFIG_MACH_GATEWAY7001)	+= gateway7001-setup.o
 obj-$(CONFIG_MACH_WG302V2)	+= wg302v2-setup.o
 obj-$(CONFIG_MACH_FSG)		+= fsg-setup.o
+obj-$(CONFIG_MACH_GORAMO_MLR)	+= goramo_mlr.o
 
 obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
 obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o

arch/arm/mach-ixp4xx/goramo_mlr.c

+/*
+ * Goramo MultiLink router platform code
+ * Copyright (C) 2006-2009 Krzysztof Halasa <khc@pm.waw.pl>
+ */
+
+#include <linux/delay.h>
+#include <linux/hdlc.h>
+#include <linux/i2c-gpio.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/serial_8250.h>
+#include <asm/mach-types.h>
+#include <asm/system.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+#include <asm/mach/pci.h>
+
+#define xgpio_irq(n)		(IRQ_IXP4XX_GPIO ## n)
+#define gpio_irq(n)		xgpio_irq(n)
+
+#define SLOT_ETHA		0x0B	/* IDSEL = AD21 */
+#define SLOT_ETHB		0x0C	/* IDSEL = AD20 */
+#define SLOT_MPCI		0x0D	/* IDSEL = AD19 */
+#define SLOT_NEC		0x0E	/* IDSEL = AD18 */
+
+#define IRQ_ETHA		IRQ_IXP4XX_GPIO4
+#define IRQ_ETHB		IRQ_IXP4XX_GPIO5
+#define IRQ_NEC			IRQ_IXP4XX_GPIO3
+#define IRQ_MPCI		IRQ_IXP4XX_GPIO12
+
+/* GPIO lines */
+#define GPIO_SCL		0
+#define GPIO_SDA		1
+#define GPIO_STR		2
+#define GPIO_HSS0_DCD_N		6
+#define GPIO_HSS1_DCD_N		7
+#define GPIO_HSS0_CTS_N		10
+#define GPIO_HSS1_CTS_N		11
+#define GPIO_HSS1_RTS_N		13
+#define GPIO_HSS0_RTS_N		14
+
+/* Control outputs from 74HC4094 */
+#define CONTROL_HSS0_CLK_INT	0
+#define CONTROL_HSS1_CLK_INT	1
+#define CONTROL_HSS0_DTR_N	2
+#define CONTROL_HSS1_DTR_N	3
+#define CONTROL_EXT		4
+#define CONTROL_AUTO_RESET	5
+#define CONTROL_PCI_RESET_N	6
+#define CONTROL_EEPROM_WC_N	7
+
+/* offsets from start of flash ROM = 0x50000000 */
+#define CFG_ETH0_ADDRESS	0x40 /* 6 bytes */
+#define CFG_ETH1_ADDRESS	0x46 /* 6 bytes */
+#define CFG_REV			0x4C /* u32 */
+#define CFG_SDRAM_SIZE		0x50 /* u32 */
+#define CFG_SDRAM_CONF		0x54 /* u32 */
+#define CFG_SDRAM_MODE		0x58 /* u32 */
+#define CFG_SDRAM_REFRESH	0x5C /* u32 */
+
+#define CFG_HW_BITS		0x60 /* u32 */
+#define  CFG_HW_USB_PORTS	0x00000007 /* 0 = no NEC chip, 1-5 = ports # */
+#define  CFG_HW_HAS_PCI_SLOT	0x00000008
+#define  CFG_HW_HAS_ETH0	0x00000010
+#define  CFG_HW_HAS_ETH1	0x00000020
+#define  CFG_HW_HAS_HSS0	0x00000040
+#define  CFG_HW_HAS_HSS1	0x00000080
+#define  CFG_HW_HAS_UART0	0x00000100
+#define  CFG_HW_HAS_UART1	0x00000200
+#define  CFG_HW_HAS_EEPROM	0x00000400
+
+#define FLASH_CMD_READ_ARRAY	0xFF
+#define FLASH_CMD_READ_ID	0x90
+#define FLASH_SER_OFF		0x102 /* 0x81 in 16-bit mode */
+
+static u32 hw_bits = 0xFFFFFFFD;    /* assume all hardware present */;
+static u8 control_value;
+
+static void set_scl(u8 value)
+{
+	gpio_line_set(GPIO_SCL, !!value);
+	udelay(3);
+}
+
+static void set_sda(u8 value)
+{
+	gpio_line_set(GPIO_SDA, !!value);
+	udelay(3);
+}
+
+static void set_str(u8 value)
+{
+	gpio_line_set(GPIO_STR, !!value);
+	udelay(3);
+}
+
+static inline void set_control(int line, int value)
+{
+	if (value)
+		control_value |=  (1 << line);
+	else
+		control_value &= ~(1 << line);
+}
+
+
+static void output_control(void)
+{
+	int i;
+
+	gpio_line_config(GPIO_SCL, IXP4XX_GPIO_OUT);
+	gpio_line_config(GPIO_SDA, IXP4XX_GPIO_OUT);
+
+	for (i = 0; i < 8; i++) {
+		set_scl(0);
+		set_sda(control_value & (0x80 >> i)); /* MSB first */
+		set_scl(1);	/* active edge */
+	}
+
+	set_str(1);
+	set_str(0);
+
+	set_scl(0);
+	set_sda(1);		/* Be ready for START */
+	set_scl(1);
+}
+
+
+static void (*set_carrier_cb_tab[2])(void *pdev, int carrier);
+
+static int hss_set_clock(int port, unsigned int clock_type)
+{
+	int ctrl_int = port ? CONTROL_HSS1_CLK_INT : CONTROL_HSS0_CLK_INT;
+
+	switch (clock_type) {
+	case CLOCK_DEFAULT:
+	case CLOCK_EXT:
+		set_control(ctrl_int, 0);
+		output_control();
+		return CLOCK_EXT;
+
+	case CLOCK_INT:
+		set_control(ctrl_int, 1);
+		output_control();
+		return CLOCK_INT;
+
+	default:
+		return -EINVAL;
+	}
+}
+
+static irqreturn_t hss_dcd_irq(int irq, void *pdev)
+{
+	int i, port = (irq == gpio_irq(GPIO_HSS1_DCD_N));
+	gpio_line_get(port ? GPIO_HSS1_DCD_N : GPIO_HSS0_DCD_N, &i);
+	set_carrier_cb_tab[port](pdev, !i);
+	return IRQ_HANDLED;
+}
+
+
+static int hss_open(int port, void *pdev,
+		    void (*set_carrier_cb)(void *pdev, int carrier))
+{
+	int i, irq;
+
+	if (!port)
+		irq = gpio_irq(GPIO_HSS0_DCD_N);
+	else
+		irq = gpio_irq(GPIO_HSS1_DCD_N);
+
+	gpio_line_get(port ? GPIO_HSS1_DCD_N : GPIO_HSS0_DCD_N, &i);
+	set_carrier_cb(pdev, !i);
+
+	set_carrier_cb_tab[!!port] = set_carrier_cb;
+
+	if ((i = request_irq(irq, hss_dcd_irq, 0, "IXP4xx HSS", pdev)) != 0) {
+		printk(KERN_ERR "ixp4xx_hss: failed to request IRQ%i (%i)\n",
+		       irq, i);
+		return i;
+	}
+
+	set_control(port ? CONTROL_HSS1_DTR_N : CONTROL_HSS0_DTR_N, 0);
+	output_control();
+	gpio_line_set(port ? GPIO_HSS1_RTS_N : GPIO_HSS0_RTS_N, 0);
+	return 0;
+}
+
+static void hss_close(int port, void *pdev)
+{
+	free_irq(port ? gpio_irq(GPIO_HSS1_DCD_N) : gpio_irq(GPIO_HSS0_DCD_N),
+		 pdev);
+	set_carrier_cb_tab[!!port] = NULL; /* catch bugs */
+
+	set_control(port ? CONTROL_HSS1_DTR_N : CONTROL_HSS0_DTR_N, 1);
+	output_control();
+	gpio_line_set(port ? GPIO_HSS1_RTS_N : GPIO_HSS0_RTS_N, 1);
+}
+
+
+/* Flash memory */
+static struct flash_platform_data flash_data = {
+	.map_name	= "cfi_probe",
+	.width		= 2,
+};
+
+static struct resource flash_resource = {
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device device_flash = {
+	.name		= "IXP4XX-Flash",
+	.id		= 0,
+	.dev		= { .platform_data = &flash_data },
+	.num_resources	= 1,
+	.resource	= &flash_resource,
+};
+
+
+/* I^2C interface */
+static struct i2c_gpio_platform_data i2c_data = {
+	.sda_pin	= GPIO_SDA,
+	.scl_pin	= GPIO_SCL,
+};
+
+static struct platform_device device_i2c = {
+	.name		= "i2c-gpio",
+	.id		= 0,
+	.dev		= { .platform_data = &i2c_data },
+};
+
+
+/* IXP425 2 UART ports */
+static struct resource uart_resources[] = {
+	{
+		.start		= IXP4XX_UART1_BASE_PHYS,
+		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= IXP4XX_UART2_BASE_PHYS,
+		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
+		.flags		= IORESOURCE_MEM,
+	}
+};
+
+static struct plat_serial8250_port uart_data[] = {
+	{
+		.mapbase	= IXP4XX_UART1_BASE_PHYS,
+		.membase	= (char __iomem *)IXP4XX_UART1_BASE_VIRT +
+			REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART1,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{
+		.mapbase	= IXP4XX_UART2_BASE_PHYS,
+		.membase	= (char __iomem *)IXP4XX_UART2_BASE_VIRT +
+			REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART2,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{ },
+};
+
+static struct platform_device device_uarts = {
+	.name			= "serial8250",
+	.id			= PLAT8250_DEV_PLATFORM,
+	.dev.platform_data	= uart_data,
+	.num_resources		= 2,
+	.resource		= uart_resources,
+};
+
+
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info eth_plat[] = {
+	{
+		.phy		= 0,
+		.rxq		= 3,
+		.txreadyq	= 32,
+	}, {
+		.phy		= 1,
+		.rxq		= 4,
+		.txreadyq	= 33,
+	}
+};
+
+static struct platform_device device_eth_tab[] = {
+	{
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEB,
+		.dev.platform_data	= eth_plat,
+	}, {
+		.name			= "ixp4xx_eth",
+		.id			= IXP4XX_ETH_NPEC,
+		.dev.platform_data	= eth_plat + 1,
+	}
+};
+
+
+/* IXP425 2 synchronous serial ports */
+static struct hss_plat_info hss_plat[] = {
+	{
+		.set_clock	= hss_set_clock,
+		.open		= hss_open,
+		.close		= hss_close,
+		.txreadyq	= 34,
+	}, {
+		.set_clock	= hss_set_clock,
+		.open		= hss_open,
+		.close		= hss_close,
+		.txreadyq	= 35,
+	}
+};
+
+static struct platform_device device_hss_tab[] = {
+	{
+		.name			= "ixp4xx_hss",
+		.id			= 0,
+		.dev.platform_data	= hss_plat,
+	}, {
+		.name			= "ixp4xx_hss",
+		.id			= 1,
+		.dev.platform_data	= hss_plat + 1,
+	}
+};
+
+
+static struct platform_device *device_tab[6] __initdata = {
+	&device_flash,		/* index 0 */
+};
+
+static inline u8 __init flash_readb(u8 __iomem *flash, u32 addr)
+{
+#ifdef __ARMEB__
+	return __raw_readb(flash + addr);
+#else
+	return __raw_readb(flash + (addr ^ 3));
+#endif
+}
+
+static inline u16 __init flash_readw(u8 __iomem *flash, u32 addr)
+{
+#ifdef __ARMEB__
+	return __raw_readw(flash + addr);
+#else
+	return __raw_readw(flash + (addr ^ 2));
+#endif
+}
+
+static void __init gmlr_init(void)
+{
+	u8 __iomem *flash;
+	int i, devices = 1; /* flash */
+
+	ixp4xx_sys_init();
+
+	if ((flash = ioremap(IXP4XX_EXP_BUS_BASE_PHYS, 0x80)) == NULL)
+		printk(KERN_ERR "goramo-mlr: unable to access system"
+		       " configuration data\n");
+	else {
+		system_rev = __raw_readl(flash + CFG_REV);
+		hw_bits = __raw_readl(flash + CFG_HW_BITS);
+
+		for (i = 0; i < ETH_ALEN; i++) {
+			eth_plat[0].hwaddr[i] =
+				flash_readb(flash, CFG_ETH0_ADDRESS + i);
+			eth_plat[1].hwaddr[i] =
+				flash_readb(flash, CFG_ETH1_ADDRESS + i);
+		}
+
+		__raw_writew(FLASH_CMD_READ_ID, flash);
+		system_serial_high = flash_readw(flash, FLASH_SER_OFF);
+		system_serial_high <<= 16;
+		system_serial_high |= flash_readw(flash, FLASH_SER_OFF + 2);
+		system_serial_low = flash_readw(flash, FLASH_SER_OFF + 4);
+		system_serial_low <<= 16;
+		system_serial_low |= flash_readw(flash, FLASH_SER_OFF + 6);
+		__raw_writew(FLASH_CMD_READ_ARRAY, flash);
+
+		iounmap(flash);
+	}
+
+	switch (hw_bits & (CFG_HW_HAS_UART0 | CFG_HW_HAS_UART1)) {
+	case CFG_HW_HAS_UART0:
+		memset(&uart_data[1], 0, sizeof(uart_data[1]));
+		device_uarts.num_resources = 1;
+		break;
+
+	case CFG_HW_HAS_UART1:
+		device_uarts.dev.platform_data = &uart_data[1];
+		device_uarts.resource = &uart_resources[1];
+		device_uarts.num_resources = 1;
+		break;
+	}
+	if (hw_bits & (CFG_HW_HAS_UART0 | CFG_HW_HAS_UART1))
+		device_tab[devices++] = &device_uarts; /* max index 1 */
+
+	if (hw_bits & CFG_HW_HAS_ETH0)
+		device_tab[devices++] = &device_eth_tab[0]; /* max index 2 */
+	if (hw_bits & CFG_HW_HAS_ETH1)
+		device_tab[devices++] = &device_eth_tab[1]; /* max index 3 */
+
+	if (hw_bits & CFG_HW_HAS_HSS0)
+		device_tab[devices++] = &device_hss_tab[0]; /* max index 4 */
+	if (hw_bits & CFG_HW_HAS_HSS1)
+		device_tab[devices++] = &device_hss_tab[1]; /* max index 5 */
+
+	if (hw_bits & CFG_HW_HAS_EEPROM)
+		device_tab[devices++] = &device_i2c; /* max index 6 */
+
+	gpio_line_config(GPIO_SCL, IXP4XX_GPIO_OUT);
+	gpio_line_config(GPIO_SDA, IXP4XX_GPIO_OUT);
+	gpio_line_config(GPIO_STR, IXP4XX_GPIO_OUT);
+	gpio_line_config(GPIO_HSS0_RTS_N, IXP4XX_GPIO_OUT);
+	gpio_line_config(GPIO_HSS1_RTS_N, IXP4XX_GPIO_OUT);
+	gpio_line_config(GPIO_HSS0_DCD_N, IXP4XX_GPIO_IN);
+	gpio_line_config(GPIO_HSS1_DCD_N, IXP4XX_GPIO_IN);
+	set_irq_type(gpio_irq(GPIO_HSS0_DCD_N), IRQ_TYPE_EDGE_BOTH);
+	set_irq_type(gpio_irq(GPIO_HSS1_DCD_N), IRQ_TYPE_EDGE_BOTH);
+
+	set_control(CONTROL_HSS0_DTR_N, 1);
+	set_control(CONTROL_HSS1_DTR_N, 1);
+	set_control(CONTROL_EEPROM_WC_N, 1);
+	set_control(CONTROL_PCI_RESET_N, 1);
+	output_control();
+
+	msleep(1);	      /* Wait for PCI devices to initialize */
+
+	flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+	flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
+
+	platform_add_devices(device_tab, devices);
+}
+
+
+#ifdef CONFIG_PCI
+static void __init gmlr_pci_preinit(void)
+{
+	set_irq_type(IRQ_ETHA, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_ETHB, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_NEC, IRQ_TYPE_LEVEL_LOW);
+	set_irq_type(IRQ_MPCI, IRQ_TYPE_LEVEL_LOW);
+	ixp4xx_pci_preinit();
+}
+
+static void __init gmlr_pci_postinit(void)
+{
+	if ((hw_bits & CFG_HW_USB_PORTS) >= 2 &&
+	    (hw_bits & CFG_HW_USB_PORTS) < 5) {
+		/* need to adjust number of USB ports on NEC chip */
+		u32 value, addr = BIT(32 - SLOT_NEC) | 0xE0;
+		if (!ixp4xx_pci_read(addr, NP_CMD_CONFIGREAD, &value)) {
+			value &= ~7;
+			value |= (hw_bits & CFG_HW_USB_PORTS);
+			ixp4xx_pci_write(addr, NP_CMD_CONFIGWRITE, value);
+		}
+	}
+}
+
+static int __init gmlr_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	switch(slot) {
+	case SLOT_ETHA:	return IRQ_ETHA;
+	case SLOT_ETHB:	return IRQ_ETHB;
+	case SLOT_NEC:	return IRQ_NEC;
+	default:	return IRQ_MPCI;
+	}
+}
+
+static struct hw_pci gmlr_hw_pci __initdata = {
+	.nr_controllers = 1,
+	.preinit	= gmlr_pci_preinit,
+	.postinit	= gmlr_pci_postinit,
+	.swizzle	= pci_std_swizzle,
+	.setup		= ixp4xx_setup,
+	.scan		= ixp4xx_scan_bus,
+	.map_irq	= gmlr_map_irq,
+};
+
+static int __init gmlr_pci_init(void)
+{
+	if (machine_is_goramo_mlr() &&
+	    (hw_bits & (CFG_HW_USB_PORTS | CFG_HW_HAS_PCI_SLOT)))
+		pci_common_init(&gmlr_hw_pci);
+	return 0;
+}
+
+subsys_initcall(gmlr_pci_init);
+#endif /* CONFIG_PCI */
+
+
+MACHINE_START(GORAMO_MLR, "MultiLink")
+	/* Maintainer: Krzysztof Halasa */
+	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC,
+	.map_io		= ixp4xx_map_io,
+	.init_irq	= ixp4xx_init_irq,
+	.timer		= &ixp4xx_timer,
+	.boot_params	= 0x0100,
+	.init_machine	= gmlr_init,
+MACHINE_END