Merge tag 'renesas-dt-for-v4.15' of...

Merge tag 'renesas-dt-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc Pull "Renesas ARM Based SoC DT Updates for v4.15" from Simon Horman: * r7s72100 (RZ/A1) Peach board - Add pin groups for SCIF2 serial debug interface and Ethernet This avoids relying on bootloader settings - Support control of LED1 using gpio-leds * r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs - Add MSIOF[012] support and define aliases for spi[0123] * r8a7743 (RZ/G1M) SoC - Add I2C and IIC core nodes * r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven development platform - Enable SDHI1 SD controller supporting high-speed and SDR50 transfers - Add chosen node to allow correct selection of serial console and the kernel command line - Enable RTC support - Enable USB2.0 host support This includes enabling USB PHY and internal PCI * r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven and r8a7745 (RZ/G1E) iW-RainboW-G22M-SM SoMs - Enable Add SPI NOR support This devices is used to boot up the system to the SoM DT * r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven SoM - Enable SDHI0 SD controller supporting high-speed transfers * r8a7745 (RZ/G1E) iW-RainboW-G22D development platform - Add pnctl support for scif4 This avoids reling on boot loader settings - Add EtherAVB support * r8a7745 (RZ/G1E) iW-RainboW-G22M-SM SoM - Add basic SoM support - Enable MMCIF eMMC support - Enable RTC support - Enable SDHI1 SD controller supporting high-speed transfers * r8a779[0-4] R-Car Gen2 SoCs - Add reset control properties Geert Uytterhoeven says: This patch series describes the reset topology on all R-Car Gen2 Socs, like was done before for R-Car Gen3 and RZ/G1. Resets usually match the corresponding module clocks. Exceptions are: - The audio module has resets for the Serial Sound Interfaces only, - The display module has only a single reset for all DU channels, but adding reset properties for the display is postponed upon request from Laurent. - Convert to new CPG/MSSR bindings Geert Uytterhoven says: Currently Renesas R-Car Gen2 SoCs use the common clk-rcar-gen2, clk-mstp, and clk-div6 drivers, which depend on most clocks being described in DT. Especially the module (MSTP) clocks are cumbersome and error prone, due to 3 arrays (clocks, clock-indices, and clock-output-names) to be kept in sync. In addition, the clk-mstp driver cannot be extended easily to also support module resets, which are provided by the same hardware module. Hence when developing support for R-Car Gen3 SoCs, another approach was chosen, which led to the CPG/MSSR driver core, and SoC-specific subdrivers (initially for R-Car Gen3, but later also for RZ/G1). This series converts the various R-Car Gen2 DTSes to migrate to the new CPG/MSSR drivers that were added in v4.13-rc1. * r8a779[0,1,3,4] R-Car Gen2 SoCs - Stop grouping clocks under a "clocks" subnode Geert Uytterhoeven says: The current practice is to not group clocks under a "clocks" subnode, but just put them together with the other on-SoC devices. Hence this patch series implements this for the various R-Car Gen2 DTSes that still need this (r8a7792.dtsi is OK). * r8a7794 (E2) Alt board - Correct inverted sense of SD wip pins * tag 'renesas-dt-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (48 commits) ARM: dts: r8a7743: Add MSIOF[012] support ARM: dts: r8a7745: Add MSIOF[012] support ARM: dts: iwg22d: Enable SDHI0 controller ARM: dts: iwg22m: Add SPI NOR support ARM: dts: r8a7745: Add QSPI support ARM: dts: iwg20m: Add SPI NOR support ARM: dts: r8a7743: Add QSPI support ARM: dts: iwg22m: Enable SDHI1 controller ARM: dts: r8a7745: Add SDHI controllers ARM: dts: r8a7794: Add reset control properties ARM: dts: r8a7793: Add reset control properties ARM: dts: r8a7792: Add reset control properties ARM: dts: r8a7791: Add reset control properties ARM: dts: r8a7790: Add reset control properties ARM: dts: r8a7743: Add IIC cores to dtsi ARM: dts: alt: use correct logic for SD WP pins ARM: dts: iwg20d-q7: Enable USB PHY ARM: dts: iwg20d-q7: Enable internal PCI ARM: dts: r8a7743: Link PCI USB devices to USB PHY ARM: dts: r8a7743: Add USB PHY DT support ...

Merge tag 'renesas-dt-for-v4.15' of...
Merge tag 'renesas-dt-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc Pull "Renesas ARM Based SoC DT Updates for v4.15" from Simon Horman: * r7s72100 (RZ/A1) Peach board - Add pin groups for SCIF2 serial debug interface and Ethernet This avoids relying on bootloader settings - Support control of LED1 using gpio-leds * r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs - Add MSIOF[012] support and define aliases for spi[0123] * r8a7743 (RZ/G1M) SoC - Add I2C and IIC core nodes * r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven development platform - Enable SDHI1 SD controller supporting high-speed and SDR50 transfers - Add chosen node to allow correct selection of serial console and the kernel command line - Enable RTC support - Enable USB2.0 host support This includes enabling USB PHY and internal PCI * r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven and r8a7745 (RZ/G1E) iW-RainboW-G22M-SM SoMs - Enable Add SPI NOR support This devices is used to boot up the system to the SoM DT * r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven SoM - Enable SDHI0 SD controller supporting high-speed transfers * r8a7745 (RZ/G1E) iW-RainboW-G22D development platform - Add pnctl support for scif4 This avoids reling on boot loader settings - Add EtherAVB support * r8a7745 (RZ/G1E) iW-RainboW-G22M-SM SoM - Add basic SoM support - Enable MMCIF eMMC support - Enable RTC support - Enable SDHI1 SD controller supporting high-speed transfers * r8a779[0-4] R-Car Gen2 SoCs - Add reset control properties Geert Uytterhoeven says: This patch series describes the reset topology on all R-Car Gen2 Socs, like was done before for R-Car Gen3 and RZ/G1. Resets usually match the corresponding module clocks. Exceptions are: - The audio module has resets for the Serial Sound Interfaces only, - The display module has only a single reset for all DU channels, but adding reset properties for the display is postponed upon request from Laurent. - Convert to new CPG/MSSR bindings Geert Uytterhoven says: Currently Renesas R-Car Gen2 SoCs use the common clk-rcar-gen2, clk-mstp, and clk-div6 drivers, which depend on most clocks being described in DT. Especially the module (MSTP) clocks are cumbersome and error prone, due to 3 arrays (clocks, clock-indices, and clock-output-names) to be kept in sync. In addition, the clk-mstp driver cannot be extended easily to also support module resets, which are provided by the same hardware module. Hence when developing support for R-Car Gen3 SoCs, another approach was chosen, which led to the CPG/MSSR driver core, and SoC-specific subdrivers (initially for R-Car Gen3, but later also for RZ/G1). This series converts the various R-Car Gen2 DTSes to migrate to the new CPG/MSSR drivers that were added in v4.13-rc1. * r8a779[0,1,3,4] R-Car Gen2 SoCs - Stop grouping clocks under a "clocks" subnode Geert Uytterhoeven says: The current practice is to not group clocks under a "clocks" subnode, but just put them together with the other on-SoC devices. Hence this patch series implements this for the various R-Car Gen2 DTSes that still need this (r8a7792.dtsi is OK). * r8a7794 (E2) Alt board - Correct inverted sense of SD wip pins * tag 'renesas-dt-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (48 commits) ARM: dts: r8a7743: Add MSIOF[012] support ARM: dts: r8a7745: Add MSIOF[012] support ARM: dts: iwg22d: Enable SDHI0 controller ARM: dts: iwg22m: Add SPI NOR support ARM: dts: r8a7745: Add QSPI support ARM: dts: iwg20m: Add SPI NOR support ARM: dts: r8a7743: Add QSPI support ARM: dts: iwg22m: Enable SDHI1 controller ARM: dts: r8a7745: Add SDHI controllers ARM: dts: r8a7794: Add reset control properties ARM: dts: r8a7793: Add reset control properties ARM: dts: r8a7792: Add reset control properties ARM: dts: r8a7791: Add reset control properties ARM: dts: r8a7790: Add reset control properties ARM: dts: r8a7743: Add IIC cores to dtsi ARM: dts: alt: use correct logic for SD WP pins ARM: dts: iwg20d-q7: Enable USB PHY ARM: dts: iwg20d-q7: Enable internal PCI ARM: dts: r8a7743: Link PCI USB devices to USB PHY ARM: dts: r8a7743: Add USB PHY DT support ...
063f7c82 · Arnd Bergmann · c305cf33 · 7031a219 · 063f7c82 · 063f7c82
21 changed file
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -725,6 +725,7 @@ dtb-$(CONFIG_ARCH_RENESAS) += \
 	r8a7740-armadillo800eva.dtb \
 	r8a7743-iwg20d-q7.dtb \
 	r8a7743-sk-rzg1m.dtb \
+	r8a7745-iwg22d-sodimm.dtb \
 	r8a7745-sk-rzg1e.dtb \
 	r8a7778-bockw.dtb \
 	r8a7779-marzen.dtb \

--- a/arch/arm/boot/dts/r7s72100-gr-peach.dts
+++ b/arch/arm/boot/dts/r7s72100-gr-peach.dts
@@ -11,6 +11,8 @@
 /dts-v1/;
 #include "r7s72100.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/r7s72100-pinctrl.h>
 / {
 	model = "GR-Peach";
@@ -28,7 +30,6 @@
 	memory@20000000 {
 		device_type = "memory";
 		reg = <0x20000000 0x00a00000>;
 	};
 	lbsc {
@@ -51,6 +52,22 @@
 			reg = <0x00600000 0x00200000>;
 		};
 	};
+leds {
+		status = "okay";
+		compatible = "gpio-leds";
+		led1 {
+			gpios = <&port6 12 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+&pinctrl {
+	scif2_pins: serial2 {
+		/* P6_2 as RxD2; P6_3 as TxD2 */
+		pinmux = <RZA1_PINMUX(6, 2, 7)>, <RZA1_PINMUX(6, 3, 7)>;
+	};
 };
 &extal_clk {
@@ -62,5 +79,8 @@
 };
 &scif2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&scif2_pins>;
 	status = "okay";
 };
--- a/arch/arm/boot/dts/r8a7743-iwg20d-q7.dts
+++ b/arch/arm/boot/dts/r8a7743-iwg20d-q7.dts
@@ -19,9 +19,42 @@
 		serial0 = &scif0;
 		ethernet0 = &avb;
 	};
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
+		stdout-path = "serial0:115200n8";
+	};
+	vcc_sdhi1: regulator-vcc-sdhi1 {
+		compatible = "regulator-fixed";
+		regulator-name = "SDHI1 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 16 GPIO_ACTIVE_LOW>;
+	};
+	vccq_sdhi1: regulator-vccq-sdhi1 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHI1 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
+		gpios-states = <1>;
+		states = <3300000 1
+			  1800000 0>;
+	};
 };
 &pfc {
+	i2c2_pins: i2c2 {
+		groups = "i2c2";
+		function = "i2c2";
+	};
 	scif0_pins: scif0 {
 		groups = "scif0_data_d";
 		function = "scif0";
@@ -31,6 +64,28 @@
 		groups = "avb_mdio", "avb_gmii";
 		function = "avb";
 	};
+	sdhi1_pins: sd1 {
+		groups = "sdhi1_data4", "sdhi1_ctrl";
+		function = "sdhi1";
+		power-source = <3300>;
+	};
+	sdhi1_pins_uhs: sd1_uhs {
+		groups = "sdhi1_data4", "sdhi1_ctrl";
+		function = "sdhi1";
+		power-source = <1800>;
+	};
+	usb0_pins: usb0 {
+		groups = "usb0";
+		function = "usb0";
+	};
+	usb1_pins: usb1 {
+		groups = "usb1";
+		function = "usb1";
+	};
 };
 &scif0 {
@@ -54,3 +109,45 @@
 		micrel,led-mode = <1>;
 	};
 };
+&sdhi1 {
+	pinctrl-0 = <&sdhi1_pins>;
+	pinctrl-1 = <&sdhi1_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+	vmmc-supply = <&vcc_sdhi1>;
+	vqmmc-supply = <&vccq_sdhi1>;
+	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+	sd-uhs-sdr50;
+	status = "okay";
+};
+&i2c2 {
+	pinctrl-0 = <&i2c2_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	clock-frequency = <400000>;
+	rtc@68 {
+		compatible = "ti,bq32000";
+		reg = <0x68>;
+	};
+};
+&pci0 {
+	status = "okay";
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+};
+&pci1 {
+	status = "okay";
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+};
+&usbphy {
+	status = "okay";
+};
--- a/arch/arm/boot/dts/r8a7743-iwg20m.dtsi
+++ b/arch/arm/boot/dts/r8a7743-iwg20m.dtsi
@@ -9,6 +9,7 @@
 */
 #include "r8a7743.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 / {
 	compatible = "iwave,g20m", "renesas,r8a7743";
@@ -42,6 +43,17 @@
 		groups = "mmc_data8_b", "mmc_ctrl";
 		function = "mmc";
 	};
+	qspi_pins: qspi {
+		groups = "qspi_ctrl", "qspi_data2";
+		function = "qspi";
+	};
+	sdhi0_pins: sd0 {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <3300>;
+	};
 };
 &mmcif0 {
@@ -53,3 +65,34 @@
 	non-removable;
 	status = "okay";
 };
+&qspi {
+	pinctrl-0 = <&qspi_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	/* WARNING - This device contains the bootloader. Handle with care. */
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "sst,sst25vf016b", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <1>;
+		m25p,fast-read;
+		spi-cpol;
+		spi-cpha;
+	};
+};
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_3p3v>;
+	cd-gpios = <&gpio7 11 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
--- a/arch/arm/boot/dts/r8a7743.dtsi
+++ b/arch/arm/boot/dts/r8a7743.dtsi
@@ -25,6 +25,13 @@
 		i2c3 = &i2c3;
 		i2c4 = &i2c4;
 		i2c5 = &i2c5;
+		i2c6 = &iic0;
+		i2c7 = &iic1;
+		i2c8 = &iic3;
+		spi0 = &qspi;
+		spi1 = &msiof0;
+		spi2 = &msiof1;
+		spi3 = &msiof2;
 	};
 	cpus {
@@ -436,6 +443,58 @@
 			status = "disabled";
 		};
+		iic0: i2c@e6500000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,iic-r8a7743",
+				     "renesas,rcar-gen2-iic",
+				     "renesas,rmobile-iic";
+			reg = <0 0xe6500000 0 0x425>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 318>;
+			dmas = <&dmac0 0x61>, <&dmac0 0x62>,
+			       <&dmac1 0x61>, <&dmac1 0x62>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
+			resets = <&cpg 318>;
+			status = "disabled";
+		};
+		iic1: i2c@e6510000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,iic-r8a7743",
+				     "renesas,rcar-gen2-iic",
+				     "renesas,rmobile-iic";
+			reg = <0 0xe6510000 0 0x425>;
+			interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 323>;
+			dmas = <&dmac0 0x65>, <&dmac0 0x66>,
+			       <&dmac1 0x65>, <&dmac1 0x66>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
+			resets = <&cpg 323>;
+			status = "disabled";
+		};
+		iic3: i2c@e60b0000 {
+			/* doesn't need pinmux */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,iic-r8a7743",
+				     "renesas,rcar-gen2-iic",
+				     "renesas,rmobile-iic";
+			reg = <0 0xe60b0000 0 0x425>;
+			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 926>;
+			dmas = <&dmac0 0x77>, <&dmac0 0x78>,
+			       <&dmac1 0x77>, <&dmac1 0x78>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
+			resets = <&cpg 926>;
+			status = "disabled";
+		};
 		scifa0: serial@e6c40000 {
 			compatible = "renesas,scifa-r8a7743",
 				     "renesas,rcar-gen2-scifa", "renesas,scifa";
@@ -779,6 +838,204 @@
 			max-frequency = <97500000>;
 			status = "disabled";
 		};
+		qspi: spi@e6b10000 {
+			compatible = "renesas,qspi-r8a7743", "renesas,qspi";
+			reg = <0 0xe6b10000 0 0x2c>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 917>;
+			dmas = <&dmac0 0x17>, <&dmac0 0x18>,
+			       <&dmac1 0x17>, <&dmac1 0x18>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&cpg 917>;
+			status = "disabled";
+		};
+		msiof0: spi@e6e20000 {
+			compatible = "renesas,msiof-r8a7743",
+				     "renesas,rcar-gen2-msiof";
+			reg = <0 0xe6e20000 0 0x0064>;
+			interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 000>;
+			dmas = <&dmac0 0x51>, <&dmac0 0x52>,
+			       <&dmac1 0x51>, <&dmac1 0x52>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&cpg 000>;
+			status = "disabled";
+		};
+		msiof1: spi@e6e10000 {
+			compatible = "renesas,msiof-r8a7743",
+				     "renesas,rcar-gen2-msiof";
+			reg = <0 0xe6e10000 0 0x0064>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 208>;
+			dmas = <&dmac0 0x55>, <&dmac0 0x56>,
+			       <&dmac1 0x55>, <&dmac1 0x56>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&cpg 208>;
+			status = "disabled";
+		};
+		msiof2: spi@e6e00000 {
+			compatible = "renesas,msiof-r8a7743",
+				     "renesas,rcar-gen2-msiof";
+			reg = <0 0xe6e00000 0 0x0064>;
+			interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 205>;
+			dmas = <&dmac0 0x41>, <&dmac0 0x42>,
+			       <&dmac1 0x41>, <&dmac1 0x42>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&cpg 205>;
+			status = "disabled";
+		};
+		sdhi0: sd@ee100000 {
+			compatible = "renesas,sdhi-r8a7743";
+			reg = <0 0xee100000 0 0x328>;
+			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 314>;
+			dmas = <&dmac0 0xcd>, <&dmac0 0xce>,
+			       <&dmac1 0xcd>, <&dmac1 0xce>;
+			dma-names = "tx", "rx", "tx", "rx";
+			max-frequency = <195000000>;
+			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
+			resets = <&cpg 314>;
+			status = "disabled";
+		};
+		sdhi1: sd@ee140000 {
+			compatible = "renesas,sdhi-r8a7743";
+			reg = <0 0xee140000 0 0x100>;
+			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 312>;
+			dmas = <&dmac0 0xc1>, <&dmac0 0xc2>,
+			       <&dmac1 0xc1>, <&dmac1 0xc2>;
+			dma-names = "tx", "rx", "tx", "rx";
+			max-frequency = <97500000>;
+			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
+			resets = <&cpg 312>;
+			status = "disabled";
+		};
+		sdhi2: sd@ee160000 {
+			compatible = "renesas,sdhi-r8a7743";
+			reg = <0 0xee160000 0 0x100>;
+			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 311>;
+			dmas = <&dmac0 0xd3>, <&dmac0 0xd4>,
+			       <&dmac1 0xd3>, <&dmac1 0xd4>;
+			dma-names = "tx", "rx", "tx", "rx";
+			max-frequency = <97500000>;
+			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
+			resets = <&cpg 311>;
+			status = "disabled";
+		};
+		usbphy: usb-phy@e6590100 {
+			compatible = "renesas,usb-phy-r8a7743",
+				     "renesas,rcar-gen2-usb-phy";
+			reg = <0 0xe6590100 0 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&cpg CPG_MOD 704>;
+			clock-names = "usbhs";
+			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
+			resets = <&cpg 704>;
+			status = "disabled";
+			usb0: usb-channel@0 {
+				reg = <0>;
+				#phy-cells = <1>;
+			};
+			usb2: usb-channel@2 {
+				reg = <2>;
+				#phy-cells = <1>;
+			};
+		};
+		pci0: pci@ee090000 {
+			compatible = "renesas,pci-r8a7743",
+				     "renesas,pci-rcar-gen2";
+			device_type = "pci";
+			reg = <0 0xee090000 0 0xc00>,
+			      <0 0xee080000 0 0x1100>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 703>;
+			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
+			resets = <&cpg 703>;
+			status = "disabled";
+			bus-range = <0 0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			ranges = <0x02000000 0 0xee080000 0 0xee080000 0 0x00010000>;
+			interrupt-map-mask = <0xff00 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH
+					 0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH
+					 0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			usb@1,0 {
+				reg = <0x800 0 0 0 0>;
+				phys = <&usb0 0>;
+				phy-names = "usb";
+			};
+			usb@2,0 {
+				reg = <0x1000 0 0 0 0>;
+				phys = <&usb0 0>;
+				phy-names = "usb";
+			};
+		};
+		pci1: pci@ee0d0000 {
+			compatible = "renesas,pci-r8a7743",
+				     "renesas,pci-rcar-gen2";
+			device_type = "pci";
+			reg = <0 0xee0d0000 0 0xc00>,
+			      <0 0xee0c0000 0 0x1100>;
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 703>;
+			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
+			resets = <&cpg 703>;
+			status = "disabled";
+			bus-range = <1 1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			ranges = <0x02000000 0 0xee0c0000 0 0xee0c0000 0 0x00010000>;
+			interrupt-map-mask = <0xff00 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
+					 0x0800 0 0 1 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
+					 0x1000 0 0 2 &gic GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			usb@1,0 {
+				reg = <0x10800 0 0 0 0>;
+				phys = <&usb2 0>;
+				phy-names = "usb";
+			};
+			usb@2,0 {
+				reg = <0x11000 0 0 0 0>;
+				phys = <&usb2 0>;
+				phy-names = "usb";
+			};
+		};
 	};
 	/* External root clock */

--- a/arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts
+++ b/arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts
+/*
+ * Device Tree Source for the iWave-RZG1E SODIMM carrier board
+ *
+ * Copyright (C) 2017 Renesas Electronics Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+/dts-v1/;
+#include "r8a7745-iwg22m.dtsi"
+/ {
+	model = "iWave Systems RainboW-G22D-SODIMM board based on RZ/G1E";
+	compatible = "iwave,g22d", "iwave,g22m", "renesas,r8a7745";
+	aliases {
+		serial0 = &scif4;
+		ethernet0 = &avb;
+	};
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
+		stdout-path = "serial0:115200n8";
+	};
+	vccq_sdhi0: regulator-vccq-sdhi0 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+		gpios-states = <1>;
+		states = <3300000 1
+			  1800000 0>;
+	};
+};
+&pfc {
+	scif4_pins: scif4 {
+		groups = "scif4_data_b";
+		function = "scif4";
+	};
+	avb_pins: avb {
+		groups = "avb_mdio", "avb_gmii";
+		function = "avb";
+	};
+	sdhi0_pins: sd0 {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <3300>;
+	};
+};
+&scif4 {
+	pinctrl-0 = <&scif4_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+&avb {
+	pinctrl-0 = <&avb_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&phy3>;
+	phy-mode = "gmii";
+	renesas,no-ether-link;
+	status = "okay";
+	phy3: ethernet-phy@3 {
+	/*
+	 * On some older versions of the platform (before R4.0) the phy address
+	 * may be 1 or 3. The address is fixed to 3 for R4.0 onwards.
+	 */
+		reg = <3>;
+		micrel,led-mode = <1>;
+	};
+};
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&vccq_sdhi0>;
+	cd-gpios = <&gpio6 6 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
--- a/arch/arm/boot/dts/r8a7745-iwg22m.dtsi
+++ b/arch/arm/boot/dts/r8a7745-iwg22m.dtsi
+/*
+ * Device Tree Source for the iWave-RZG1E-G22M SODIMM SOM
+ *
+ * Copyright (C) 2017 Renesas Electronics Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+#include "r8a7745.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+/ {
+	compatible = "iwave,g22m", "renesas,r8a7745";
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0x20000000>;
+	};
+	reg_3p3v: 3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+&extal_clk {
+	clock-frequency = <20000000>;
+};
+&pfc {
+	mmcif0_pins: mmc {
+		groups = "mmc_data8", "mmc_ctrl";
+		function = "mmc";
+	};
+	qspi_pins: qspi {
+		groups = "qspi_ctrl", "qspi_data2";
+		function = "qspi";
+	};
+	sdhi1_pins: sd1 {
+		groups = "sdhi1_data4", "sdhi1_ctrl";
+		function = "sdhi1";
+		power-source = <3300>;
+	};
+	i2c3_pins: i2c3 {
+		groups = "i2c3_b";
+		function = "i2c3";
+	};
+};
+&mmcif0 {
+	pinctrl-0 = <&mmcif0_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_3p3v>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+&qspi {
+	pinctrl-0 = <&qspi_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	/* WARNING - This device contains the bootloader. Handle with care. */
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "sst,sst25vf016b", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <1>;
+		m25p,fast-read;
+		spi-cpol;
+		spi-cpha;
+	};
+};
+&sdhi1 {
+	pinctrl-0 = <&sdhi1_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_3p3v>;
+	cd-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+&i2c3 {
+	pinctrl-0 = <&i2c3_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	clock-frequency = <400000>;
+	rtc@68 {
+		compatible = "ti,bq32000";
+		reg = <0x68>;
+	};
+};
--- a/arch/arm/boot/dts/r8a7745.dtsi
+++ b/arch/arm/boot/dts/r8a7745.dtsi
@@ -18,6 +18,19 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		spi0 = &qspi;
+		spi1 = &msiof0;
+		spi2 = &msiof1;
+		spi3 = &msiof2;
+	};
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -65,6 +78,111 @@
 			resets = <&cpg 408>;
 		};
+		gpio0: gpio@e6050000 {
+			compatible = "renesas,gpio-r8a7745",
+				     "renesas,rcar-gen2-gpio";
+			reg = <0 0xe6050000 0 0x50>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 0 32>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 912>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 912>;
+		};
+		gpio1: gpio@e6051000 {
+			compatible = "renesas,gpio-r8a7745",
+				     "renesas,rcar-gen2-gpio";
+			reg = <0 0xe6051000 0 0x50>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 32 26>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 911>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 911>;
+		};
+		gpio2: gpio@e6052000 {
+			compatible = "renesas,gpio-r8a7745",
+				     "renesas,rcar-gen2-gpio";
+			reg = <0 0xe6052000 0 0x50>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 64 32>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 910>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 910>;
+		};
+		gpio3: gpio@e6053000 {
+			compatible = "renesas,gpio-r8a7745",
+				     "renesas,rcar-gen2-gpio";
+			reg = <0 0xe6053000 0 0x50>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 96 32>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 909>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 909>;
+		};
+		gpio4: gpio@e6054000 {
+			compatible = "renesas,gpio-r8a7745",
+				     "renesas,rcar-gen2-gpio";
+			reg = <0 0xe6054000 0 0x50>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 128 32>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 908>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 908>;
+		};
+		gpio5: gpio@e6055000 {
+			compatible = "renesas,gpio-r8a7745",
+				     "renesas,rcar-gen2-gpio";
+			reg = <0 0xe6055000 0 0x50>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 160 28>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 907>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 907>;
+		};
+		gpio6: gpio@e6055400 {
+			compatible = "renesas,gpio-r8a7745",
+				     "renesas,rcar-gen2-gpio";
+			reg = <0 0xe6055400 0 0x50>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 192 26>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 905>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 905>;
+		};
 		irqc: interrupt-controller@e61c0000 {
 			compatible = "renesas,irqc-r8a7745", "renesas,irqc";
 			#interrupt-cells = <2>;
@@ -508,6 +626,225 @@
 			#size-cells = <0>;
 			status = "disabled";
 		};
+		avb: ethernet@e6800000 {
+			compatible = "renesas,etheravb-r8a7745",
+				     "renesas,etheravb-rcar-gen2";
+			reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
+			interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 812>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 812>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+		i2c0: i2c@e6508000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,i2c-r8a7745",
+				     "renesas,rcar-gen2-i2c";
+			reg = <0 0xe6508000 0 0x40>;
+			interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 931>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 931>;
+			i2c-scl-internal-delay-ns = <6>;
+			status = "disabled";
+		};
+		i2c1: i2c@e6518000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,i2c-r8a7745",
+				     "renesas,rcar-gen2-i2c";
+			reg = <0 0xe6518000 0 0x40>;
+			interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 930>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 930>;
+			i2c-scl-internal-delay-ns = <6>;
+			status = "disabled";
+		};
+		i2c2: i2c@e6530000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,i2c-r8a7745",
+				     "renesas,rcar-gen2-i2c";
+			reg = <0 0xe6530000 0 0x40>;
+			interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 929>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 929>;
+			i2c-scl-internal-delay-ns = <6>;
+			status = "disabled";
+		};
+		i2c3: i2c@e6540000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,i2c-r8a7745",
+				     "renesas,rcar-gen2-i2c";
+			reg = <0 0xe6540000 0 0x40>;
+			interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 928>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 928>;
+			i2c-scl-internal-delay-ns = <6>;
+			status = "disabled";
+		};
+		i2c4: i2c@e6520000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,i2c-r8a7745",
+				     "renesas,rcar-gen2-i2c";
+			reg = <0 0xe6520000 0 0x40>;
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 927>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 927>;
+			i2c-scl-internal-delay-ns = <6>;
+			status = "disabled";
+		};
+		i2c5: i2c@e6528000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,i2c-r8a7745",
+				     "renesas,rcar-gen2-i2c";
+			reg = <0 0xe6528000 0 0x40>;
+			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 925>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 925>;
+			i2c-scl-internal-delay-ns = <6>;
+			status = "disabled";
+		};
+		mmcif0: mmc@ee200000 {
+			compatible = "renesas,mmcif-r8a7745",
+				     "renesas,sh-mmcif";
+			reg = <0 0xee200000 0 0x80>;
+			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 315>;
+			dmas = <&dmac0 0xd1>, <&dmac0 0xd2>,
+			       <&dmac1 0xd1>, <&dmac1 0xd2>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 315>;
+			reg-io-width = <4>;
+			max-frequency = <97500000>;
+			status = "disabled";
+		};
+		qspi: spi@e6b10000 {
+			compatible = "renesas,qspi-r8a7745", "renesas,qspi";
+			reg = <0 0xe6b10000 0 0x2c>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 917>;
+			dmas = <&dmac0 0x17>, <&dmac0 0x18>,
+			       <&dmac1 0x17>, <&dmac1 0x18>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&cpg 917>;
+			status = "disabled";
+		};
+		msiof0: spi@e6e20000 {
+			compatible = "renesas,msiof-r8a7745",
+				     "renesas,rcar-gen2-msiof";
+			reg = <0 0xe6e20000 0 0x0064>;
+			interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 000>;
+			dmas = <&dmac0 0x51>, <&dmac0 0x52>,
+			       <&dmac1 0x51>, <&dmac1 0x52>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&cpg 000>;
+			status = "disabled";
+		};
+		msiof1: spi@e6e10000 {
+			compatible = "renesas,msiof-r8a7745",
+				     "renesas,rcar-gen2-msiof";
+			reg = <0 0xe6e10000 0 0x0064>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 208>;
+			dmas = <&dmac0 0x55>, <&dmac0 0x56>,
+			       <&dmac1 0x55>, <&dmac1 0x56>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&cpg 208>;
+			status = "disabled";
+		};
+		msiof2: spi@e6e00000 {
+			compatible = "renesas,msiof-r8a7745",
+				     "renesas,rcar-gen2-msiof";
+			reg = <0 0xe6e00000 0 0x0064>;
+			interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 205>;
+			dmas = <&dmac0 0x41>, <&dmac0 0x42>,
+			       <&dmac1 0x41>, <&dmac1 0x42>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&cpg 205>;
+			status = "disabled";
+		};
+		sdhi0: sd@ee100000 {
+			compatible = "renesas,sdhi-r8a7745";
+			reg = <0 0xee100000 0 0x328>;
+			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 314>;
+			dmas = <&dmac0 0xcd>, <&dmac0 0xce>,
+			       <&dmac1 0xcd>, <&dmac1 0xce>;
+			dma-names = "tx", "rx", "tx", "rx";
+			max-frequency = <195000000>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 314>;
+			status = "disabled";
+		};
+		sdhi1: sd@ee140000 {
+			compatible = "renesas,sdhi-r8a7745";
+			reg = <0 0xee140000 0 0x100>;
+			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 312>;
+			dmas = <&dmac0 0xc1>, <&dmac0 0xc2>,
+			       <&dmac1 0xc1>, <&dmac1 0xc2>;
+			dma-names = "tx", "rx", "tx", "rx";
+			max-frequency = <97500000>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 312>;
+			status = "disabled";
+		};
+		sdhi2: sd@ee160000 {
+			compatible = "renesas,sdhi-r8a7745";
+			reg = <0 0xee160000 0 0x100>;
+			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 311>;
+			dmas = <&dmac0 0xd3>, <&dmac0 0xd4>,
+			       <&dmac1 0xd3>, <&dmac1 0xd4>;
+			dma-names = "tx", "rx", "tx", "rx";
+			max-frequency = <97500000>;
+			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
+			resets = <&cpg 311>;
+			status = "disabled";
+		};
 	};
 	/* External root clock */

--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -316,11 +316,8 @@
 	pinctrl-names = "default";
 	status = "okay";
-	clocks = <&mstp7_clks R8A7790_CLK_DU0>,
+	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
-		 <&mstp7_clks R8A7790_CLK_DU1>,
+		 <&cpg CPG_MOD 726>, <&cpg CPG_MOD 725>,
-		 <&mstp7_clks R8A7790_CLK_DU2>,
-		 <&mstp7_clks R8A7790_CLK_LVDS0>,
-		 <&mstp7_clks R8A7790_CLK_LVDS1>,
 		 <&x13_clk>, <&x2_clk>;
 	clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1",
 		      "dclkin.0", "dclkin.1";

--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -330,9 +330,7 @@
 	pinctrl-names = "default";
 	status = "okay";
-	clocks = <&mstp7_clks R8A7791_CLK_DU0>,
+	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 726>,
-		 <&mstp7_clks R8A7791_CLK_DU1>,
-		 <&mstp7_clks R8A7791_CLK_LVDS0>,
 		 <&x13_clk>, <&x2_clk>;
 	clock-names = "du.0", "du.1", "lvds.0",
 		      "dclkin.0", "dclkin.1";

--- a/arch/arm/boot/dts/r8a7791-porter.dts
+++ b/arch/arm/boot/dts/r8a7791-porter.dts
@@ -419,9 +419,7 @@
 	pinctrl-names = "default";
 	status = "okay";
-	clocks = <&mstp7_clks R8A7791_CLK_DU0>,
+	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 726>,
-		 <&mstp7_clks R8A7791_CLK_DU1>,
-		 <&mstp7_clks R8A7791_CLK_LVDS0>,
 		 <&x3_clk>, <&x16_clk>;
 	clock-names = "du.0", "du.1", "lvds.0",
 		      "dclkin.0", "dclkin.1";

--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
--- a/arch/arm/boot/dts/r8a7792-blanche.dts
+++ b/arch/arm/boot/dts/r8a7792-blanche.dts
@@ -310,8 +310,7 @@
 	pinctrl-0 = <&du0_pins &du1_pins>;
 	pinctrl-names = "default";
-	clocks = <&mstp7_clks R8A7792_CLK_DU0>, <&mstp7_clks R8A7792_CLK_DU1>,
+	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&x1_clk>, <&x2_clk>;
-		 <&x1_clk>, <&x2_clk>;
 	clock-names = "du.0", "du.1", "dclkin.0", "dclkin.1";
 	status = "okay";

--- a/arch/arm/boot/dts/r8a7792-wheat.dts
+++ b/arch/arm/boot/dts/r8a7792-wheat.dts
@@ -305,8 +305,7 @@
 	pinctrl-0 = <&du0_pins &du1_pins>;
 	pinctrl-names = "default";
-	clocks = <&mstp7_clks R8A7792_CLK_DU0>, <&mstp7_clks R8A7792_CLK_DU1>,
+	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&osc2_clk>;
-		 <&osc2_clk>;
 	clock-names = "du.0", "du.1", "dclkin.0";
 	status = "okay";

--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
--- a/arch/arm/boot/dts/r8a7793-gose.dts
+++ b/arch/arm/boot/dts/r8a7793-gose.dts
@@ -303,9 +303,7 @@
 	pinctrl-names = "default";
 	status = "okay";
-	clocks = <&mstp7_clks R8A7793_CLK_DU0>,
+	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 726>,
-		 <&mstp7_clks R8A7793_CLK_DU1>,
-		 <&mstp7_clks R8A7793_CLK_LVDS0>,
 		 <&x13_clk>, <&x2_clk>;
 	clock-names = "du.0", "du.1", "lvds.0",
 		      "dclkin.0", "dclkin.1";

--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
--- a/arch/arm/boot/dts/r8a7794-alt.dts
+++ b/arch/arm/boot/dts/r8a7794-alt.dts
@@ -167,8 +167,7 @@
 	pinctrl-names = "default";
 	status = "okay";
-	clocks = <&mstp7_clks R8A7794_CLK_DU0>,
+	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>,
-		 <&mstp7_clks R8A7794_CLK_DU1>,
 		 <&x13_clk>, <&x2_clk>;
 	clock-names = "du.0", "du.1", "dclkin.0", "dclkin.1";
@@ -305,7 +304,7 @@
 	vmmc-supply = <&vcc_sdhi0>;
 	vqmmc-supply = <&vccq_sdhi0>;
 	cd-gpios = <&gpio6 6 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
 	sd-uhs-sdr50;
 	sd-uhs-sdr104;
 	status = "okay";
@@ -319,7 +318,7 @@
 	vmmc-supply = <&vcc_sdhi1>;
 	vqmmc-supply = <&vccq_sdhi1>;
 	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>;
 	sd-uhs-sdr50;
 	status = "okay";
 };

--- a/arch/arm/boot/dts/r8a7794-silk.dts
+++ b/arch/arm/boot/dts/r8a7794-silk.dts
@@ -423,8 +423,7 @@
 	pinctrl-names = "default";
 	status = "okay";
-	clocks = <&mstp7_clks R8A7794_CLK_DU0>,
+	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>,
-		 <&mstp7_clks R8A7794_CLK_DU1>,
 		 <&x2_clk>, <&x3_clk>;
 	clock-names = "du.0", "du.1", "dclkin.0", "dclkin.1";

--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi