ARM: dts: omap3-igep: OneNAND support

Add OneNAND node for IGEP and leave it disabled by default. It is up
to bootloader to enable proper node. Timing just works, but values are
copied over from N900 as I was unable to find chip datasheet.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

arch/arm/boot/dts/omap3-igep.dtsi

@@ -37,6 +37,13 @@
 };
 
 &omap3_pmx_core {
+	gpmc_pins: pinmux_gpmc_pins {
+		pinctrl-single,pins = <
+			/* OneNAND seems to require PIN_INPUT on clock. */
+                        OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0)        /* gpmc_clk.gpmc_clk */
+		>;
+	};
+
 	uart1_pins: pinmux_uart1_pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE0)	/* uart1_rx.uart1_rx */
@@ -98,6 +105,9 @@
 };
 
 &gpmc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmc_pins>;
+
 	nand@0,0 {
 		compatible = "ti,omap2-nand";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
@@ -126,6 +136,48 @@
 
 		#address-cells = <1>;
 		#size-cells = <1>;
+
+		status = "okay";
+	};
+
+	onenand@0,0 {
+		compatible = "ti,omap2-onenand";
+		reg = <0 0 0x20000>;	/* CS0, offset 0, IO size 128K */
+
+		gpmc,sync-read;
+		gpmc,sync-write;
+		gpmc,burst-length = <16>;
+		gpmc,burst-read;
+		gpmc,burst-wrap;
+		gpmc,burst-write;
+		gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */
+		gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <87>;
+		gpmc,cs-wr-off-ns = <87>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <10>;
+		gpmc,adv-wr-off-ns = <10>;
+		gpmc,oe-on-ns = <15>;
+		gpmc,oe-off-ns = <87>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <87>;
+		gpmc,rd-cycle-ns = <112>;
+		gpmc,wr-cycle-ns = <112>;
+		gpmc,access-ns = <81>;
+		gpmc,page-burst-access-ns = <15>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,clk-activation-ns = <5>;
+		gpmc,wr-data-mux-bus-ns = <30>;
+		gpmc,wr-access-ns = <81>;
+		gpmc,sync-clk-ps = <15000>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		status = "disabled";
 	};
 };