This patch enables software (and phy device) transmit time stamping
in the "Dave ethernet interface." Compile tested only.

Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@conan.davemloft.net>

This patch enables software (and phy device) transmit time stamping
for the TIGON3 driver. Compile tested only.

Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@conan.davemloft.net>

This patch enables software (and phy device) transmit time stamping
for the DaVinci EMAC driver. Tested together with the dp83640 PHY.

Cc: Anant Gole <anantgole@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@conan.davemloft.net>

The DaVinci EMAC driver does not implement any ioctls, but still it can
pass them through to the phy device. This makes it possible for a phy
to offer PHC capabilities.

Cc: Anant Gole <anantgole@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@conan.davemloft.net>

This patch has been tested on the Freescale M5234BCC, which includes the
National Semiconductor DP83640 with IEEE 1588 support.

Cc: Greg Ungerer <gerg@uclinux.org>
Cc: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>
Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@conan.davemloft.net>

The network stack provides the function, skb_clone_tx_timestamp().
Ethernet MAC drivers can call this via the transmit time stamping
hook, skb_tx_timestamp(). This commit exports the clone function so
that drivers using it can be compiled as modules.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@conan.davemloft.net>

SNMP mibs use two percpu arrays, one used in BH context, another in USER
context. With increasing number of cpus in machines, and fact that ipv6
uses per network device ipstats_mib, this is consuming a lot of memory
if many network devices are registered.

commit be281e55 (ipv6: reduce per device ICMP mib sizes) shrinked
percpu needs for ipv6, but we can reduce memory use a bit more.

With recent percpu infrastructure (irqsafe_cpu_inc() ...), we no longer
need this BH/USER separation since we can update counters in a single
x86 instruction, regardless of the BH/USER context.

Other arches than x86 might need to disable irq in their
irqsafe_cpu_inc() implementation : If this happens to be a problem, we
can make SNMP_ARRAY_SZ arch dependent, but a previous poll
( https://lkml.org/lkml/2011/3/17/174 ) to arch maintainers did not
raise strong opposition.

Only on 32bit arches, we need to disable BH for 64bit counters updates
done from USER context (currently used for IP MIB)

This also reduces vmlinux size :

1) x86_64 build
$ size vmlinux.before vmlinux.after
   text	   data	    bss	    dec	    hex	filename
7853650	1293772	1896448	11043870	 a8841e	vmlinux.before
7850578	1293772	1896448	11040798	 a8781e	vmlinux.after

2) i386  build
$ size vmlinux.before vmlinux.afterpatch
   text	   data	    bss	    dec	    hex	filename
6039335	 635076	3670016	10344427	 9dd7eb	vmlinux.before
6037342	 635076	3670016	10342434	 9dd022	vmlinux.afterpatch
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Andi Kleen <andi@firstfloor.org>
CC: Ingo Molnar <mingo@elte.hu>
CC: Tejun Heo <tj@kernel.org>
CC: Christoph Lameter <cl@linux-foundation.org>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org
CC: linux-arch@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) the setting of NETIF_F_VLAN_CHALLENGED in bond_del_vlan() is
useless since commit b2a103e6 because bond_fix_features() now
sets NETIF_F_VLAN_CHALLENGED whenever the last slave is being
removed.

2) the code never triggers anyway as vlan_list is never empty
since ad1afb00.
Signed-off-by: NJiri Bohac <jbohac@suse.cz>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NETIF_F_TSO6 for VLAN packets was not enabled for BE adapters.
Enabling it.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's no need for the guest to validate the checksum if it have been
validated by host nics. So this patch introduces a new flag -
VIRTIO_NET_HDR_F_DATA_VALID which is used to bypass the checksum
examing in guest. The backend (tap/macvtap) may set this flag when
met skbs with CHECKSUM_UNNECESSARY to save cpu utilization.

No feature negotiation is needed as old driver just ignore this flag.

Iperf shows 12%-30% performance improvement for UDP traffic. For TCP,
when gro is on no difference as it produces skb with partial
checksum. But when gro is disabled, 20% or even higher improvement
could be measured by netperf.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Given many versions of ethtool's reluctance to do anything other than
byte accesses to the EEPROM interface, it is easier to update the driver
to support byte accesses so that all the ethtool versions that have been
observed in Debian can write the EEPROM.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichio Honda <micchie@sfc.wide.ad.jp>
Acked-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FTGMAC100 Ethernet Media Access Controller supports 10/100/1000 Mbps
and MII/GMII.  This driver has been working on some ARM/NDS32 SoC's
including Faraday A369 and Andes AG102.
Signed-off-by: NPo-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

arch/m68k/emu/nfeth.c: In function ‘nfeth_init’:
arch/m68k/emu/nfeth.c:243: error: implicit declaration of function ‘request_irq’
arch/m68k/emu/nfeth.c:243: error: ‘IRQF_SHARED’ undeclared (first use in this function)
arch/m68k/emu/nfeth.c:243: error: (Each undeclared identifier is reported only once
arch/m68k/emu/nfeth.c:243: error: for each function it appears in.)
arch/m68k/emu/nfeth.c: In function ‘nfeth_cleanup’:
arch/m68k/emu/nfeth.c:266: error: implicit declaration of function ‘free_irq’
drivers/net/apne.c: In function ‘apne_probe’:
drivers/net/apne.c:189: error: implicit declaration of function ‘free_irq’
drivers/net/apne.c: In function ‘apne_probe1’:
drivers/net/apne.c:317: error: implicit declaration of function ‘request_irq’
drivers/net/apne.c:317: error: ‘IRQF_SHARED’ undeclared (first use in this function)
drivers/net/apne.c:317: error: (Each undeclared identifier is reported only once
drivers/net/apne.c:317: error: for each function it appears in.)

Introduced by commit a6b7a407 ("net: remove interrupt.h inclusion from
netdevice.h").

Include <linux/interrupt.h> in the individual drivers to fix the build.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The message size allocated for rtnl ifinfo dumps was limited to
a single page.  This is not enough for additional interface info
available with devices that support SR-IOV and caused a bug in
which VF info would not be displayed if more than approximately
40 VFs were created per interface.

Implement a new function pointer for the rtnl_register service that will
calculate the amount of data required for the ifinfo dump and allocate
enough data to satisfy the request.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes the way versioning is done for igb in the kernel by
removing the number after the "k."  It has been determined that just the
"k" is sufficient to identify a kernel version and the following number
was used in an inconsistent manner.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update the version number to match version conventions. Bump the major
version to indicate that new hardware support (i350) has been added.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 5d03078a added a redundant 'select
CRC32'; remove it.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Host Wakeup Active bit in the PHY Port General Configuration register
(page 769 register 17) must be cleared after every PHY reset to prevent an
unexpected wake signal from the PHY. Originally, this was accomplished by
simply reading the PHY Wakeup Control register on page 800 which clears the
Host Wakeup Active bit as a side-effect. Unfortunately, a hardware bug on
the 82577 and 82578 PHY can cause unexpected behavior when registers on
page 800 are accessed while in gigabit mode.

This patch changes the remaining instances when the Host Wakeup Active bit
needs to be cleared while possibly in gigabit mode by accessing the Port
General Configuration register directly instead of accessing any register
on page 800.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Doing a PHY page select can take a long time, relatively speaking. This
can cause a significant delay when updating a number of PHY registers on
the same page by unnecessarily setting the page for each PHY access. For
example when going to Sx, all the PHY wakeup registers (WUC, RAR[], MTA[],
SHRAR[], IP4AT[], IP6AT[], etc.) on 82577/8/9 need to be updated which
takes a long time which can cause issues when suspending.

This patch introduces new PHY ops function pointers to allow callers to
set the page directly and do any number of PHY accesses on that page.
This feature is currently only implemented for 82577, 82578 and 82579
PHYs for both the normally addressed registers as well as the special-
case addressing of the PHY wakeup registers on page 800. For the latter
registers, the existing function for accessing the wakeup registers has
been divided up into three- 1) enable access to the wakeup register page,
2) perform the register access and 3) disable access to the wakeup register
page. The two functions that enable/disable access to the wakeup register
page are necessarily available to the caller so that the caller can restore
the value of the Port Control (a.k.a. Wakeup Enable) register after the
wakeup register accesses are done.

All instances of writing to multiple PHY registers on the same page are
updated to use this new method and to acquire any PHY locking mechanism
before setting the page and performing the register accesses, and release
the locking mechanism afterward.

Some affiliated magic number cleanup is done as well.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Start the Tx queue when the interface is brought up in e1000e_up() but do
not schedule the queue until link is up as detected in the watchdog task
which sets netif_carrier_on.

Also flush the descriptors and clean the Tx and Rx rings before resetting
the hardware when bringing the interface down otherwise there is a small
window where the watchdog task can be triggered with netif_carrier_off
and the Tx ring not yet empty which causes an additional and unnecessary
reset.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since EXTCNF_CTRL.SWFLAG (used in the ownership arbitration of shared
resources, e.g. the PHY shared between the s/w, f/w, and h/w clients)
can be cleared by any of those clients, log a debug message when
software attempts to clear it and it is already cleared unexpectedly.
And since the swflag is cleared by a hardware reset, the driver does
not need to do that, but the mutex acquired when the bit is set must
still be cleared.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When repeatedly cycling Sx->S0 states with the network cable unplugged,
the 82579 PHY may not initialize as expected and may require a full power
cycle to recover functionality to the device.  Workaround this by testing
access of the PHY registers after resuming; if that returns unexpected
results toggle the LANPHYPC signal to power cycle the PHY.

This is implemented in the new function e1000_resume_workarounds_pchlan()
which calls another new function, e1000_toggle_lanphypc_value_ich8lan(),
which has been created to reduce code duplication (same functionality
required by a previous workaround).  Also, e1000e_disable_gig_wol_ich8lan
is now e1000_suspend_workarounds_ich8lan to better reflect what it does.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ESB2 LAN includes a debug feature that enables far-end loopback (FELB)
of the SerDes/Kumeran interface.  This feature is activated when receiving
a sequence of symbols that includes a reserved codeword.  On a perfect
link, FELB would never be activated.  In the presence of bit errors, there
is a very small, but non-zero, probability of FELB being activated.

If the FELB is activated, the SerDes link becomes non-functional and must
be reset.  It could also corrupt the switching tables in the switch since
the ESB2 is transmitting packets with a different source MAC address.

This patch disables the FELB feature.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now all received packets are handled by bond_handle_frame,
and arp_mon_pt isn't used any more.
Reviewed-by: NWANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: NWeiping Pan <panweiping3@gmail.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now we use agg_select_timer and ad_work.
Reviewed-by: NWANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: NWeiping Pan <panweiping3@gmail.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bond_params->ad_select and ad_bond_info->agg_select_mode have the same
meaning, they are duplicate and need extra synchronization.

__get_agg_selection_mode() get ad_select from bond_params directly.
Signed-off-by: NWeiping Pan <panweiping3@gmail.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These is also a bug, that if you modify lacp_rate via sysfs,
and add new slaves in bonding, new slaves won't use the latest lacp_rate,
since ad_bond_info->lacp_fast is initialized only once,
in bond_3ad_initialize().

Since both struct bond_params and ad_bond_info have lacp_fast,
they are duplicate and need extra synchronization.

bond_3ad_bind_slave() can use bond_params->lacp_fast to initialize port.
So we can just remove lacp_fast from struct ad_bond_info.
Signed-off-by: NWeiping Pan <panweiping3@gmail.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is bug that when you modify lacp_rate via sysfs,
802.3ad won't use the new value of lacp_rate to transmit packets.
This is because port->actor_oper_port_state isn't changed.
Signed-off-by: NWeiping Pan <panweiping3@gmail.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NDanny Guo <dannguo@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid Wang <dwang2@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of deriving the index of a transmit/receive interrupt resource
from the transmit/receive queue index, always save and retrieve it
using an additional variable.
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NDanny Guo <dannguo@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid Wang <dwang2@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NDanny Guo <dannguo@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid Wang <dwang2@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

enic driver currently passes 802.1p bits to the upper layers for packets
tagged with non-zero vlan ids only. This patch extends such behaviour to
zero vlan tagged packets also.

The patch is dependant on the following kernel patches:

1) vlan_dev: VLAN 0 should be treated as "no vlan tag" (802.1p packet)
   - net-next-2.6 git commit: ad1afb00
   - Available 2.6.36 and later
2) vlan: Centralize handling of hardware acceleration.
  - net-next-2.6 git commit: 3701e513
  - Available 2.6.37 and later
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NDanny Guo <dannguo@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid Wang <dwang2@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The definition NO_FLAGS was introduced to make the code more
readable and shall be used to initialize flag fields.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

CodingStyle "Chapter 12: Macros, Enums and RTL" recommends to use enums
for several related constants. Internal states can be used without
defining the actual value, but all values which are visible to the
outside must be defined as before. Normal values are assigned as usual
and flags are defined by shifts of a bit.
Signed-off-by: NSven Eckelmann <sven@narfation.org>

CodingStyle "Chapter 12: Macros, Enums and RTL" highly recommends to use
functions instead of macros were possible. This ensures type safety and
prevents shadowing of other variables.
Signed-off-by: NSven Eckelmann <sven@narfation.org>