Because the plane registers are different in Skylake we need to adapt
the MMIO code as well.

v2: Don't introduce yet another vfunc when the direction is do
consolidate the plane updates to use the same code path (Daniel)

v3:
  - Use enum pipe instead of int (Ville)
  - Also update PLANE_STRIDE when the tiling has changed (Ville)
  - Put intel_mark_page_flip_active() in the shared code (Damien)

v4:
  - Remove unused variable

v5:
  - Fix whitespace Vs tabs (Ville)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Put the DPLL0 state readout in skylake_get_ddi_pll(), closer to
where the PLL assignement read out is done rather than the frequency
readout function. (Daniel)

v3: Remove stray new line (Damien)
    Add Paulo's r-b tag for v1

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On pre-HSW we have two encoders per digital port: one HDMI, one DP.
However they are the same physical port in hardware and we can't enable
both at the same time. Reject the modeset if the user attempts this.

So far we've been saved by the fact that we never see both HDMI and DP
connectors as connected. But if the user decides to force a mode anyway,
all kinds of funny stuff might happen.

Unfortunately we don't seem to have any way to inform userspace that
such configurations are invalid except by returning an error from
setcrtc. possible_clones only covers real cloning situations, and
looking at the connector names doesn't work either since we don't
always register both connectors for the same port. I suppose the
only way to fix that would be to expose only a single encoder per
digital port like we do on HSW+ but that would be a fairly large
undertaking for little gain.

kms_setmode hits this since it forces modes on non-connected VGA and
HDMI connectors. Previosuly it just resulted in weirdness such as
failed link training. With this patch it will now get an error back
from the kernel and will die with an assert since it thinks that the
configuration should be fine.

v2: Deal with INTEL_OUTPUT_UNKNOWN (Paulo)

Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The GPU reset also resets the display on gen3/4. The g33 docs say we
should disable all planes before flipping the reset switch. Just
disable all the crtcs instead. That seems a nicer thing to do anyway.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On gen4 and earlier the GPU reset also resets the display, so we should
protect against concurrent modeset operations. Grab all the modeset locks
around the entire GPU reset dance, remebering first ti dislogde any
pending page flip to make sure we don't deadlock. Any pageflip coming
in between these two steps should fail anyway due to reset_in_progress,
so this should be safe.

This fixes a lot of failed asserts in the modeset code when there's a
modeset racing with the reset. Naturally the asserts aren't happy when
the expected state has disappeared.

v2: Drop UMS checks, complete pending flips after the reset (Daniel)

Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When doing a nop modeset we currently leave crtc->new_config point at
the already freed temporary pipe_config. That will anger the sanity
checks in intel_modeset_update_state() when the nop modeset gets
followed by a GPU reset on gen3/4 where the display block gets fully
reinitialized during the reset.

So leave crtc->new_config alone until we know a modeset is actually
required.

Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

During a GPU reset we need to get pending page flip cleared out
since the ring contents are gone and flip will never complete
on its own. This used to work until the mmio vs. CS flip race
detection came about. That piece of code is looking for a
specific surface address in the SURFLIVE register, but as
a flip to that address may never happen the check may never
pass. So we should just skip the SURFLIVE and flip counter
checks when the GPU gets reset.

intel_display_handle_reset() tries to effectively complete
the flip anyway by calling .update_primary_plane(). But that
may not satisfy the conditions of the mmio vs. CS race
detection since there's no guarantee that a modeset didn't
sneak in between the GPU reset and intel_display_handle_reset().
Such a modeset will not wait for pending flips due to the ongoing GPU
reset, and then the primary plane updates performed by
intel_display_handle_reset() will already use the new surface
address, and thus the surface address the flip is waiting for
might never appear in SURFLIVE. The result is that the flip
will never complete and attempts to perform further page flips
will fail with -EBUSY.

During the GPU reset intel_crtc_has_pending_flip() will return
false regardless, so the deadlock with a modeset vs. the error
work acquiring crtc->mutex was avoided. And the reset_counter
check in intel_crtc_has_pending_flip() actually made this bug
even less severe since it allowed normal modesets to go through
even though there's a pending flip.

This is a regression introduced by me here:
 commit 75f7f3ec
 Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
 Date:   Tue Apr 15 21:41:34 2014 +0300

    drm/i915: Fix mmio vs. CS flip race on ILK+

Testcase: igt/kms_flip/flip-vs-panning-vs-hang
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Currently after doing DPMS-OFF on all outputs CDCLK won't be set to its
minimum value as it should. A subsequent modeset to turn off all outputs
will thus run with all power domains disabled, and notice that it needs
to change CDCLK to its minimum value. Since the power domains are
disabled this will emit a register-access-while-suspended WARN and fail
to set the minimum freq.

The proper solution for this is to set the minimum frequency during
DPMS-OFF. That needs a bigger rework that would take into account the
user DPMS setting too during the calculation of the new modesetting
configuration. Until that's done this stop-gap solution gets the PIPE-A
power domain during setting the CDCLK; this domain covers the HW blocks
needed for this.

Idea to use PIPE-A domain from Ville.

Testcase: igt/pm_rpm
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Makes it easier to debug infoframe mismatches.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

With the deprecation of UMS, and by association DRI1, we have a tough
choice when updating the ring access routines. We either rewrite the
DRI1 routines blindly without testing (so likely to be broken) or take
the liberty of declaring them no longer supported and remove them
entirely. This takes the latter approach.

v2: Also remove the DRI1 sarea updates
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: Fix rebase conflicts.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

After the previous patch RPS disabling doesn't depend any more on the
first level interrupts being disabled, so we can move it everywhere
earlier. Doing so let's us think about the uninitialization steps
afterwards independently of any asynchronous RPS events that can happen
atm. It also makes the system/runtime suspend time RPS disabling more
uniform. Finally this gets rid of the WARN in
intel_suspend_gt_powersave(), which we can hit if a final RPS work runs
after we disabled the first level interrupts.

Testcase: igt/pm_rpm
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When using the universal plane interface, the source rectangle
coordinates define the panning offset for the primary plane, which needs
to be stored in crtc->{x,y}.  The original universal plane code
negelected to set these panning offset fields, which was partially
remedied in:

        commit ccc759dc
        Author: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
        Date:   Wed Sep 24 14:20:22 2014 -0300

            drm/i915: Merge of visible and !visible paths for primary planes

However the plane source coordinates are provided in 16.16 fixed point
format and the above commit forgot to convert back to integer
coordinates before saving the values.  When we replace
intel_pipe_set_base() with plane->funcs->update_plane() in a future
patch, this bug becomes visible via the set_config entrypoint as well as
update_plane.

Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Testcase: igt/kms_plane
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When invalid cloning configurations were detected during modeset, we
never copied the error code into the return value variable, leading us
to return 0 (success) to userspace.

This regression has been introduced in

commit 50f52756
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Fri Nov 7 13:11:00 2014 -0800

    drm/i915: use compute_config in set_config v4

Testcase: igt/kms_setmode
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86226Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

No functional changes. Just cleaning and reorganizing it.

v2: Rebase it puting it to begin of psr rework. This helps to blame easily
at least latest changes.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When reading out a DDI config that uses a PLL that is not part of the
shared_dpll scheme (DPLL0), it's totally normal to end up in the
default: case of that switch.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This moved around on SKL, so we need to make sure we read/write the
correct regs.

v2: fixup WIN_POS offsets (Paulo)
    zero out WIN_POS reg at disable time (Paulo)
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuougseek.org>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A few bits have changed in MI_DISPLAY_FLIP to accomodate the new planes.
DE_RRMR seems to have kept its plane flip bits backward compatible.

v2: Rebase on top of nightly
v3: Rebase on top of nightly (minor conflict in i915_reg.h)
v4: Remove code that is now part of intel_crtc_page_flip()
    Don't use BUG() in default:
    Use intel_crtc->unpin_work->gtt_offset
    (Paulo)
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: rebase on top of the hw state flattening.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Modify the implementation to query DPLL attached to a SKL port.

v2: Rebase on top of the run-time PM on DPMS series (Damien)

v3: Modified as per review comments from Paulo
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NSatheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some machines may have a broken VBT or no VBT at all, but we still want
to use SSC there.  So check for it and keep it enabled if we see it
already on.  Based on an earlier fix from Kristian.

v2: honor modparam if set too (Daniel)
    read out at init time and store for panel_use_ssc() use (Jesse)
v3: trust BIOS configuration over VBT like we do for DP (Jani)
Reported-by: NKristian Høgsberg <hoegsberg@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This only affects the fastboot path as-is.  In that case, we simply need
to make sure that we update the pipe size at the first mode set.  Rather
than putting it off until we decide to flip (if indeed we do end up
flipping), update the pipe size as appropriate a bit earlier in the
set_config call.

This sets us up for better pipe tracking in later patches.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If these change (e.g. after a modeset following a fastboot), we need to
do a full mode set.

v2:
  - put under pipe_config check so we don't deref a null state (Jesse)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is useful for checking things later.

v2:
  - fix hsw infoframe enabled check (Ander)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Add the missing PIPE_CONF_CHECK_I(has_infoframe); line to the
hw state cross-checker.]
[danet: Squash in fixup from Jesse to correctly compute has_infoframe
in the hdmi compute_config function.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This will allow us to consult more info before deciding whether to flip
or do a full mode set.

v2:
  - don't use uninitialized or incorrect pipe masks in set_config
    failure path (Ander)
v3:
  - fixup for pipe_config changes in compute_config (Jesse)
v4:
  - drop spurious hunk in force restore path (Ander)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This allows us to calculate the full pipe config before we do any mode
setting work.

v2:
  - clarify comments about global vs. per-crtc mode set (Ander)
  - clean up unnecessary pipe_config = NULL setting (Ander)
v3:
  - fix pipe_config handling (alloc in compute_config, free in set_mode) (Jesse)
  - fix arg order in set_mode (Jesse)
  - fix failure path of set_config (Ander)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently we register the backlight device as soon as we register the
connector. That means we can get backlight requests from userspace
already before reading out the current modeset hardware state.

That means we don't yet know the current crtc->encoder->connector mapping,
which causes problems for VLV/CHV which need to know the current pipe in
order to figure out which BLC registers to poke. Currently we just
ignore such requests fairly deep in the backlight code which means the
backlight device brightness property will get out of sync with our
backlight.level and the actual hardware state.

Fix the problem by delaying the backlight device registration until the
entire modeset init has been performed. And we also move the
backlight unregisteration to happen as the first thing during the
modeset cleanup so that we also won't be bothered with userspace
backlight requested during teardown.

This is a real world problem on machines using systemd, because systemd,
for some reason, wants to restore the backlight to the level it used last
time. And that happens as soon as it sees the backlight device appearing
in the system. Sometimes the userspace access makes it through before
the modeset init, sometimes not.

v2: Do not lie to the user in the debug prints (Jani)
    Include connector name in the prints (Jani)
    Fix a typo in the commit message (Jani)
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If the connector would have an encoder but the encoder didn't have a
crtc we might dereference a NULL crtc here. I suppose that should never
happen due to intel_sanitize_encoder(), but let's be a bit paranoid
print a warning if we ever hit this and return INVALID_PIPE to the
caller.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since a8bb6818 __intel_framebuffer_create() is called
with struct_mutex held, so it should use drm_gem_object_unreference()
instead of drm_gem_object_unreference_unlocked().

Found by Linux Driver Verification project (linuxtesting.org).

This regression has been introduced in

commit a8bb6818
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Mon Feb 10 18:00:39 2014 +0100

    drm/i915: Fix error path leak in fbdev fb allocation
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Use the new pipe config values to calculate the updated pll dividers.

This regression was introduced in

commit 0dbdf89f27b17ae1eceed6782c2917f74cbb5d59
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date:   Wed Oct 29 11:32:33 2014 +0200

    drm/i915: Add infrastructure for choosing DPLLs before disabling crtcs

	and

	commit 00d958817dd3daaa452c221387ddaf23d1e4c06f
	Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
	Date:   Wed Oct 29 11:32:36 2014 +0200

	    drm/i915: Covert remaining platforms to choose DPLLS before disabling CRTCs

v2: Use intel_pipe_will_have_type() to look at new configuration - Ander
Signed-off-by: NBob Paauwe <bob.j.paauwe@intel.com>
CC: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Tested-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The cleanup path would reset pll->new_config to NULL but wouldn't free
the allocated memory.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Turned out to be much simpler on top of my latest atomic stuff than
what I've feared. Some details:

- Drop the modeset_lock_all snakeoil in drm_plane_init. Same
  justification as for the equivalent change in drm_crtc_init done in

	commit d0fa1af4
	Author: Daniel Vetter <daniel.vetter@ffwll.ch>
	Date:   Mon Sep 8 09:02:49 2014 +0200

	    drm: Drop modeset locking from crtc init function

  Without these the drm_modeset_lock_init would fall over the exact
  same way.

- Since the atomic core code wraps the locking switching it to
  per-plane locks was a one-line change.

- For the legacy ioctls add a plane argument to the locking helper so
  that we can grab the right plane lock (cursor or primary). Since the
  universal cursor plane might not be there, or someone really crazy
  might forgoe the primary plane even accept NULL.

- Add some locking WARN_ON to the atomic helpers for good paranoid
  measure and to check that it all works out.

Tested on my exynos atomic hackfest with full lockdep checks and ww
backoff injection.

v2: I've forgotten about the load-detect code in i915.

v3: Thierry reported that in latest 3.18-rc vmwgfx doesn't compile any
more due to

commit 21e88620
Author: Rob Clark <robdclark@gmail.com>
Date:   Thu Oct 30 13:39:04 2014 -0400

    drm/vmwgfx: fix lock breakage

Rebased and fix this up.

Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We need the HPLL frequency when calculating cdclk. Currently we read
that out from the hardware every single time, which isn't going to fly
very well if the device is runtime suspended. So cache the HPLL
frequency in dev_priv and use the cached value.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This simplifies the code quite a bit compared to iterating over all
rings during the ring interrupt.

Also, it allows us to drop the mmio_flip spinlock, since the mmio_flip
struct is only accessed in two places. The first is when the flip is
queued and the other when the mmio writes are done. Since a flip cannot
be queued while there is a pending flip, the two paths shouldn't ever
run in parallel. We might need to revisit that if support for replacing
flips is implemented though.

v2: Don't hold dev->struct_mutext while waiting (Chris)

v3: Make the wait uninterruptable (Chris)
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We may need to access various hardware bits in the .global_resources()
hook, so move the call to occur after enabling all the newly required
power wells, but before disabling all the now unneeded wells. This
should guarantee that we have all the sufficient hardware resources
available during the .global_resources() call. And if not, any additional
resources must be explicitly acquired by the .global_resorces() hook.

For instance on VLV/CHV we need to access the gunit mailbox so that we
can talk to punit/cck over sideband. In addition some PFI credit
reprogramming may need to be addes as well, which may require the disp2d
well.

This should also make the power domain refcounts consistent on platforms
which don't have a .global_resource() hook since now they too will
call modeset_update_crtc_power_domains() which will drop the init power.
Previously init power was just left enabled for such platforms.

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Don't check DDB on pre-SKL platforms
    Don't check DDB state on disabled pipes

v3: Squash "Expose skl_ddb_get_hw_state()"
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch provides the implementation for reading the pipe wm HW
state.

v2: Incorporated Damien's review comments and also made modifications
    to incorporate the plane/cursor split.

v3: No need to ident a line that was fitting 80 chars
    Return early instead of indenting the remaining of a function
    (Damien)

v4: Rebase on top of nightly (minor conflict in intel_drv.h)
v5: Rebase on top of nightly (minor conflict in intel_drv.h)
v6: Rebase on top of nightly (minor conflict in intel_drv.h)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NPradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently we program just DPSCNTR and DSPSTRIDE directly from the ring
interrupt handler, which is fine since the hardware guarantees that
those are update atomically. When we have atomic page flips we'll want
to be able to update also the offset registers, and then we need to use
the vblank evade mechanism to guarantee atomicity. Since that mechanism
introduces a wait, we need to do the actual register write from a work
when it is triggered by the ring interrupt.

v2: Explain the need for mmio_flip.work in the commit message (Paulo)
    Initialize the mmio_flip work in intel_crtc_init() (Paulo)
    Prevent new flips the previous flip work finishes (Paulo)
    Don't acquire modeset locks for mmio flip work

Note: Paulo had reservations about the work item leaking over a plane
disable. But insofar as we do lack these checks that issue is already
present with the existing code.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It will help future code if this function knows something about of the context
of the display setup object is being pinned for.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As Paulo said when introducing the enum, having more types is really
good to document what should go where (int foo(int, int, bool, bool).

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's really part of the "push all new_* state into current state
pointers" done in that function. So let's move it there to make this
clear.

Also, with the conversion done the num_shared_dpll check the function
does in it's loop is enough, so we can drop the check for the dpll
compute callback, too.

Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>