If no valid MAC address could be obtained from the hardware,
fall back to a randomly generated one.
Signed-off-by: NPavel Machek <pavel@denx.de>
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FW was initialized with data from wrong header, this caused TSO packets
have wrong IP csum.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MAC addresses assigned by the PF to VFs were not kept in the PF driver
admin table. As a result, displaying the VF MACs from the PF interface
to user space showed zero address where in fact the VF got non-zero
address from the PF, fix that.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a VF sense they didn't get MAC address, use random one. This will
address the case of administrator not assigning MAC to the VF through
the PF OS APIs and keep udev happy.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the PF initialization, SRIOV is enabled before the PF is fully initialized.
This allows the kernel to probe the newly-exposed VFs before the PF is ready
to handle them (nested probes).

Have the probe method return the -EPROBE_DEFER value in this situation (instead
of the VF probe method retrying its initialization in a loop, and returning -EIO
on failure). When -EPROBE_DEFER is returned by the VF probe method, the kernel
itself will retry the probe after a suitable delay.

Based upon a suggestion by Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When turning on adaptive_rx under adaptive moderation, the CQ's moderation
count wasn't updated according to rx_frames which resulted in too many
interrupts and bandwidth drop.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smatch reports the following warnings:
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:514 pcan_usb_pro_drv_loaded() error: doing dma on the stack (buffer)
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:878 pcan_usb_pro_init() error: doing dma on the stack (&fi)
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:889 pcan_usb_pro_init() error: doing dma on the stack (&bi)

See "Documentation/DMA-API-HOWTO.txt" section "What memory is DMA'able?"

Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

smatch reports the following warnings:
drivers/net/can/usb/esd_usb2.c:640 esd_usb2_start() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:846 esd_usb2_close() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:855 esd_usb2_close() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:923 esd_usb2_set_bittiming() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:1047 esd_usb2_probe() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:1053 esd_usb2_probe() error: doing dma on the stack (&msg)

See "Documentation/DMA-API-HOWTO.txt" section "What memory is DMA'able?"
Signed-off-by: NOlivier Sobrie <olivier@sobrie.be>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Unlike Kvaser Leaf light devices, some other Kvaser devices (like USBcan
Pro, USBcan R) receive CAN messages in CMD_LOG_MESSAGE frames. This
patch adds support for it.

Cc: linux-stable <stable@vger.kernel.org> # >= v3.8
Signed-off-by: NJonas Peterson <jonas.peterson@gmail.com>
Signed-off-by: NOlivier Sobrie <olivier@sobrie.be>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Since the recent addition of 8021AD, we need to set the new field vlan_proto in
sk_buff. Otherwise, it will trigger BUG() call in vlan_proto_idx().

This patch fixes the problem.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case the port list dump does not fit into one skb currently the
dump would start over again. Fix this by continue from the last dumped
port.

Introduced by commit d90f889e (team: handle sending port list in the
same way option list is sent)
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During a PCI EEH/AER error recovery flow, if the device did not successfully
restart, the error_detected() hook may be called a second time with a
"perm_failure" state. This patch skips over driver cleanup for the second
invocation of the callback.

Also, Lancer error recovery code is fixed-up to handle these changes.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HW does not compute L4 checksum for IP Fragmented packets.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently allow changing the mq flag (IFF_MULTI_QUEUE) for a persistent
device. This will result a mismatch between the number the queues in netdev and
tuntap. This is because we only allocate a 1q netdevice when IFF_MULTI_QUEUE was
not specified, so when we set the IFF_MULTI_QUEUE and try to attach more queues
later, netif_set_real_num_tx_queues() may fail which result a single queue
netdevice with multiple sockets attached.

Solve this by disallowing changing the mq flag for persistent device.

Bug was introduced by commit edfb6a14
(tuntap: reduce memory using of queues).
Reported-by: NSriram Narasimhan <sriram.narasimhan@hp.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Accessing the OTP memory on AR9950 causes a data bus
like this:

  Data bus error, epc == 801f7774, ra == 801f7774
  Oops[#1]:
  CPU: 0 PID: 1 Comm: swapper Not tainted 3.10.0-rc3 #592
  task: 87c28000 ti: 87c22000 task.ti: 87c22000
  $ 0   : 00000000 00000061 deadc0de 00000000
  $ 4   : b8115f18 00015f18 00000007 00000004
  $ 8   : 00000001 7c7c3c7c 7c7c7c7c 7c7c7c7c
  $12   : 7c7c3c7c 80320a68 00000000 7c7c7c3c
  $16   : 87cd8010 00015f18 00000007 00000000
  $20   : 00000064 00000004 87c23c7c 8035210c
  $24   : 00000000 801f3674
  $28   : 87c22000 87c23b48 00000001 801f7774
  Hi    : 00000000
  Lo    : 00000064
  epc   : 801f7774 ath9k_hw_wait+0x58/0xb0
      Not tainted
  ra    : 801f7774 ath9k_hw_wait+0x58/0xb0
  Status: 1000cc03 KERNEL EXL IE
  Cause : 4080801c
  PrId  : 00019750 (MIPS 74Kc)
  Modules linked in:
  Process swapper (pid: 1, threadinfo=87c22000, task=87c28000, ts=00000000)
  Stack : 0000000f 00000061 00002710 8006240c 00000001 87cd8010 87c23bb0 87cd8010
          00000000 00000004 00000003 80210c7c 000000b3 67fa8000 0000032a 000006fe
          000003e8 00000002 00000028 87c23bf0 000003ff 80210d24 803e5630 80210e28
          00000000 00000007 87cd8010 00007044 00000004 00000061 000003ff 000001ff
          87c26000 87cd8010 00000220 87cd8bb8 80210000 8020fcf4 87c22000 87c23c08
          ...
  Call Trace:
  [<801f7774>] ath9k_hw_wait+0x58/0xb0
  [<80210c7c>] ar9300_otp_read_word+0x80/0xd4
  [<80210d24>] ar9300_read_otp+0x54/0xb0
  [<8020fcf4>] ar9300_check_eeprom_header+0x1c/0x40
  [<80210fe4>] ath9k_hw_ar9300_fill_eeprom+0x118/0x39c
  [<80206650>] ath9k_hw_eeprom_init+0x74/0xb4
  [<801f96d0>] ath9k_hw_init+0x7ec/0x96c
  [<801e65ec>] ath9k_init_device+0x340/0x758
  [<801f35d0>] ath_ahb_probe+0x21c/0x2c0
  [<801c041c>] driver_probe_device+0xc0/0x1e4
  [<801c05ac>] __driver_attach+0x6c/0xa4
  [<801bea08>] bus_for_each_dev+0x64/0xa8
  [<801bfa40>] bus_add_driver+0xcc/0x24c
  [<801c0954>] driver_register+0xbc/0x17c
  [<803f8fc0>] ath9k_init+0x5c/0x88
  [<800608fc>] do_one_initcall+0xec/0x1a0
  [<803e6a68>] kernel_init_freeable+0x13c/0x200
  [<80309cdc>] kernel_init+0x1c/0xe4
  [<80062450>] ret_from_kernel_thread+0x10/0x18

On the AR9550, the OTP registers are located at
the same address as on the AR9340. Use the correct
values to avoid the error.

Cc: stable@vger.kernel.org  # 3.6+
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For p2p client mode powersave mode should be kept disabled. It is
working but inefficient. In general p2p links do no benefit from this
mode, because these links are setup temporarily to transfer data.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Multi channel support was disabled. This patch will enable it and
configure the P2P GO on the correct frequency when multi channel
is used.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Upon deleting a P2P_CLIENT/GO interface the vif and consequently
the wdev is freed before the net_device is actually being unregistered
but cfg80211 still needs to access the wdev. Using destructor field
to free the net_device and vif.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When registration fails the net device is no longer needed. Free
the net device and remove reference to private data from the
driver.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Pass the struct brcmf_cfg80211_info instance instead of obtaining
through vif itself using vif->wdev. This is needed as the netdev
associated with this vif is already unregistered.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware requires that on p2p setup when net interfaces
are created or updated that they start initially with the same
channel as the channel in use for the current connection
(if any). If none exists take default channel 11.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ARP offloading should only be used in STA or P2P client mode. It
is currently configured once at init. When being configured for AP
ARP offloading should be turned off and when AP mode is left it can
be turned back on.

Cc: stable@vger.kernel.org
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The phy_init_eee has to exit with an error when the
local device and its link partner both do not support EEE.
So this patch fixes a problem when verify this.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In 63b77bf4

	iwlwifi: dvm: don't send zeroed LQ cmd

I tried to avoid to send zeroed LQ cmd, but I made a (very)
stupid mistake in the memcmp.
Since this patch has been ported to stable, the fix should
go to stable too.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58341

Cc: stable@vger.kernel.org
Reported-by: NHinnerk van Bruinehsen <h.v.bruinehsen@fu-berlin.de>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add the missing free_netdev() before return from function
qlge_probe() in the error handling case.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

AR934x v1.3 no longer needs the DCU backoff reduction workaround for
preventing rx overruns, but in turn needs the number of usable Tx
buffers to be reduced slightly.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a local bus timeout has been detected, the host interface needs to be
reset to clear the errors. AR934x uses a different synchronous interrupt
bit to indicate this, so the check needs to be fixed.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do not subtract spur power from noise floor on this chip, as it can lead
to packet loss and other connectivity issues.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In function be_get_nic_desc(), it will go through the descriptor array
returned from f/w. By comparing the desc_type field, it determines whether
there is a nic descriptor in the array or not. In the case of no nic
descriptor, this function should return NULL.

The code may return an invalide descriptor, when there is no nic descriptor
in the array and the desc_count is less than MAX_RESOURCE_DESC. In this case,
even there is no nic descriptor, it will still return the lase descriptor
since the i doesn't equal to MAX_RESOURCE_DESC.

This patch fix this issue by returning the descriptor when find it and return
NULL for other cases.
Signed-off-by: NWei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: NXiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Acked-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commits:

c573972c
1a590434
da2e2c21

They were meant for net-next not net.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 55257d72 (virtio-net: fill only rx
queues which are being used) only does the napi enabling during open for
curr_queue_pairs. This will break multiqueue receiving since napi of new queues
were still disabled after changing the number of queues.

This patch fixes this by enabling napi for all possible queues during open.

Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit bfd428da ("net: ethernet: sun: initialize variables directly")
dropped the only loop that was using i but did not remove the actual
variable, therefore causing a warning when building. This patch drops
the now redundant line.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit e998fd41 ("net: ethernet: korina: initialize variables directly")
dropped the only loop that was using i but did not remove the actual
variable, therefore causing a warning when building. This patch drops
the now redundant line.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 3b0aaef8 ("net: ethernet: apple: initialize variables directly")
dropped the only loop that was using i but did not remove the actual
variable, therefore causing a warning when building. This patch drops
the now redundant line.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for Cinterion's PLxx WWAN Interface by adding QMI_FIXED_INTF with
Cinterion's Vendor ID as well as Product ID and WWAN Interface Number.
Signed-off-by: NHans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
Signed-off-by: NChristian Schmiedl <christian.schmiedl@gemalto.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MVF is a family while MVF600 is a particular SoC in the family.  We
generally prefer to use SoC rather than family name in compatible string
to define a particular type of fec device.  And this is how fec_dt_ids
works for all those IMX fec variants.  Let's change mvf to mvf600 to
have it work in the same way.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o After change in EPORT features of 82xx adapter, netdev->features needs to
  be updated to reflect EPORT feature updates but driver was manipulating
  netdev->features at wrong place.
o This patch uses netdev_update_features() and .ndo_fix_features() to
  update netdev->features properly.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Code is removed because netdev->trans_start updates made by the driver
will be ignored by the kernel.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix error paths in probe to assign proper error codes to probe return value.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>