Eliminate 90 of these warnings:

Warning(..//include/net/mac80211.h:1682): No description found for parameter 'drv_priv[0]'
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

As the next patch will require the IE splitting utility functions
in cfg80211, move them there from mac80211.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows drivers to request per-vif and per-sta-tid queues from which
they can pull frames. This makes it easier to keep the hardware queues
short, and to improve fairness between clients and vifs.

The task of scheduling packet transmission is left up to the driver -
queueing is controlled by mac80211. Drivers can only dequeue packets by
calling ieee80211_tx_dequeue. This makes it possible to add active queue
management later without changing drivers using this code.

This can also be used as a starting point to implement A-MSDU
aggregation in a way that does not add artificially induced latency.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
[resolved minor context conflict, minor changes, endian annotations]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Indicating just the peer's capability is fairly pointless
if the local device doesn't support it. Make the variable
track both combined, and remove the 'local support' check
in the TX path.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This can allow the driver to take action based on the reason
of the deauth.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This can allow the driver to take action based on the
success / failure of the association.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This can allow the driver to take action based on the
success / failure of the authentication.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We will be able to add more events, such as MLME events and
others. The low level driver may be interested in knowing
about these events to dump firmware data upon failures, or
to change parameters in case connection attempts fail etc...
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This will allow mac80211 drivers to call cfg80211 APIs with
the right handle.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some device drivers offload part of aggregation including AddBA/DelBA
negotiations to firmware. In such scenario, the PMF configuration of
the station needs to be provided to driver to enable encryption of
AddBA/DelBA action frames.
Signed-off-by: NSenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
[fix commit log, documentation]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Sometimes the driver might want to modify private data in interfaces
that are down. One possible use-case is cleaning up interface state
after HW recovery. Some interfaces that were up before the recovery took
place might be down now, but they might still be "dirty".

Introduce a new iterate_interfaces() API and a new ACTIVE iterator flag.
This way the internal implementation of the both active and inactive
APIs remains the same.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Beacon's timestamp, device system time associated with this beacon and
DTIM count parameters are not updated in the associated vif context
if the latest beacon's content is identical to the previously received.
It make sense to update these changing parameters on every beacon so the
driver can get most updated values. This may be necessary, for example,
to avoid either beacons' drift effect or device time stamp overrun.
IMPORTANT: Three sync_* parameters - sync_ts, sync_device_ts and
sync_dtim_count would possibly be out of sync by the time the driver will
use them. The synchronized view is currently guaranteed only in certain
callbacks.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows mac80211 to configure BIP-GMAC-128 and BIP-GMAC-256 to the
driver and also use software-implementation within mac80211 when the
driver does not support this with hardware accelaration.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows mac80211 to configure GCMP and GCMP-256 to the driver and
also use software-implementation within mac80211 when the driver does
not support this with hardware accelaration.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
[remove a spurious newline]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Control per packet Transmit Power Control (TPC) in lower drivers
according to TX power settings configured by the user. In particular TPC is
enabled if value passed in enum nl80211_tx_power_setting is
NL80211_TX_POWER_LIMITED (allow using less than specified from userspace),
whereas TPC is disabled if nl80211_tx_power_setting is set to
NL80211_TX_POWER_FIXED (use value configured from userspace)
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some drivers unfortunately cannot support software crypto, but
mac80211 currently assumes that they do.

This has the issue that if the hardware enabling fails for some
reason, the software fallback is used, which won't work. This
clearly isn't desirable, the error should be reported and the
key setting refused.

Support this in mac80211 by allowing drivers to set a new HW
flag IEEE80211_HW_SW_CRYPTO_CONTROL, in which case mac80211 will
only allow software fallback if the set_key() method returns 1.
The driver will also need to advertise supported cipher suites
so that mac80211 doesn't advertise any (future) software ciphers
that the driver can't actually do.

While at it, to make it easier to support this, refactor the
ieee80211_init_cipher_suites() code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

These rates are treated the same as 160 MHz in the spec,
so it makes no sense to distinguish them. As no driver
uses them yet, this is also not a problem, just remove
them.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In many cases, drivers can filter things like beacons that will
skew statistics reported by mac80211. To get correct statistics
in these cases, call drivers to obtain statistics and let them
override all values, filling values from mac80211 if the driver
didn't provide them. Not all of them make sense for the driver
to fill, so some are still always done by mac80211.

Note that this doesn't currently allow a driver to say "I know
this value is wrong, don't report it at all", or to sum it up
with a mac80211 value (as could be useful for "dropped misc"),
that can be added if it turns out to be needed.

This also gets rid of the get_rssi() method as is can now be
implemented using sta_statistics().
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When hw acceleration is enabled, the GENERATE_IV or PUT_IV_SPACE flags
only require headroom space. Therefore, the tailroom-needed counter can
safely be decremented for most drivers.

The older incarnation of this patch (ca34e3b5) assumed that the above
holds true for all drivers. As reported by Christopher Chavez and
researched by Christian Lamparter and Larry Finger, this isn't a valid
assumption for p54 and cw1200.

Drivers that still require tailroom for ICV/MIC even when HW encryption
is enabled can use IEEE80211_KEY_FLAG_RESERVE_TAILROOM to indicate it.
Signed-off-by: NIdo Yariv <idox.yariv@intel.com>
Cc: Christopher Chavez <chrischavez@gmx.us>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This reverts commit ca34e3b5.

It turns out that the p54 and cw2100 drivers assume that there's
tailroom even when they don't say they really need it. However,
there's currently no way for them to explicitly say they do need
it, so for now revert this.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=90331.

Cc: stable@vger.kernel.org
Fixes: ca34e3b5 ("mac80211: Fix accounting of the tailroom-needed counter")
Reported-by: NChristopher Chavez <chrischavez@gmx.us>
Bisected-by: NLarry Finger <Larry.Finger@lwfinger.net>
Debugged-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to let drivers have more dynamic U-APSD support,
move the enablement flag to the virtual interface driver
flags. This lets drivers not only set it up differently
for different interfaces, but also enable/disable on the
fly if needed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since multicast frames are marked as no-ack, using
IEEE80211_TX_STAT_ACK to check if they have been
successfully transmitted by the driver is incorrect
since a driver can choose to ignore transmission status
for no-ack frames. This results in incorrect accounting
for such frames.

To fix this issue, this patch introduces a new flag
that can be used by drivers to indicate error-free
transmission of no-ack frames.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
[add a note about not setting the flag for non-no-ack frames]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Move IEEE80211_TX_CTL_PS_RESPONSE to info->control.flags since
this is used only in the TX path (by ath9k). This frees up
a bit which can be used for other purposes.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This can be used by drivers that cannot reliably map tx status
information onto specific skbs.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This op works like .tx_status, except it does not need access to the
skb. This will be used by drivers that cannot match tx status
information to specific packets.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Having it as a sub-event for RSSI thresholds is very ugly,
but luckily no userspace actually uses the events yet.

Move the event to its own function call internally and to
its own event attribute in nl80211.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows drivers with a firmware or chip-based rate lookup table to
use the most recent default rate selection without having to get it from
per-packet data or explicit ieee80211_get_tx_rate calls
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR with software
based scanning and generate a random MAC address for them for every
scan request with the flag.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In TDLS (e.g., TDLS off-channel) there is a requirement for
some drivers to supply an unused TID between the AP and the
device to the FW, to allow sending PTI requests and to allow
the FW to aggregate on a specific TID for better throughput.

To ensure that the allocated TID is indeed unused, this patch
introduces an API for blocking the driver from TXing on that
TID.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When receiving a TDLS channel switch request or response, parse the frame
and call a new tdls_recv_channel_switch op in the low level driver with
the parsed data.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Implement the cfg80211 TDLS channel switch ops and introduce new mac80211
ones for low-level drivers.
Verify low-level driver support for the new ops when using the relevant
wiphy feature bit. Also verify the peer supports channel switching before
passing the command down.

Add a new STA flag to track the off-channel state with the TDLS peer and
make sure to cancel the channel-switch if the peer STA is unexpectedly
removed.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Radiotap vendor namespace data might still be useful, but we
reverted it because it used too much space in the RX status.
Put it back, but address the space problem by using a single
bit only and putting everything else into the skb->data.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Drivers might want to know also when mac80211 has
completed reconfiguring after resume (e.g. in order
to know when frames can be passed to mac80211).

Rename restart_complete() to a more-generic reconfig_complete(),
and add a new enum to indicate the reconfiguration type.

Update the current users with the new prototype.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch adds 802.11p OCB (Outside the Context of a BSS) mode
support.

When communicating in OCB mode a mandatory wildcard BSSID
(48 '1' bits) is used.

The EDCA parameters handling function was changed to support
802.11p specific values.

The insertion of a newly discovered STAs is done in the similar way
as in the IBSS mode -- through the deferred insertion.

The OCB mode uses a periodic 'housekeeping task' for expiration of
disconnected STAs (in the similar manner as in the MESH mode).

New Kconfig option for verbose OCB debugging outputs is added.
Signed-off-by: NRostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The configured tx power is often limited by hardware capabilities,
channel settings, antenna configuration, etc.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
[fix tracing compilation]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This will be helpful when using the mac80211_hwsim
wiphys and automated testing.  Let user create the
vifs as needed, and named as expected.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Support creating wiphy devices with an optional name.
This will be used by hwsim to have better automated control
over virtual radio creation/deletion.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Allow drivers to iterate all stations currently uploaded to them.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some drivers need to know which station is the TDLS link initiator.
Expose this value via the mac80211 ieee80211_sta structure.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Export ieee80211_ie_split function, so it can be reused by
drivers which need to insert additional elements.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>